Results for “grid impact analysis” — Page 6

NASA NTRS1990

Influence of structural and aerodynamic modeling on optimization with flutter constraint

The influences of structural and aerodynamic modeling on multidisciplinary optimization in an aeroelastic environment are not well understood. Therefore, optimizations with flutter and frequency constraints were performed to investigate the effects these modeling factors have on various representative wings. To this end, the Automated Structural Optimization System (ASTROS) was used as a tool to minimize the weight of various fully built-up finite element wing models in subsonic and supersonic flow under given flutter and frequency constraints. First, the performance of the optimization module was tested against results from other codes on a straight and uniform wing widely used for optimization with flutter constraints. Then, fully built-up finite element models of various wings with different aspect ratios were investigated for the influence on the structural optimization for minimum weight of the following modeling factors: finite element selection, structural grid refinement; number of selected modes, retention of breathing modes; selection of reduced frequencies to be used in flutter analysis; aerodynamic panel size and placement; splining of the aerodynamic grid to the structural grid selection of extra points of the structural wing box for splining; and number of constraints to be retained. Knowledge of these influences as well as of the program behavior is important, since optimization can be made more efficient by the selection of reasonable initial models. Also, it was shown previously that modeling has an impact on the results of modal and aeroelastic analyses. Thus, if modeling errors can negatively affect the analyses, a minimum weight optimization can be jeopardized and result in an optimal design that is rather unreliable. In the following, selected results are presented and the influences of some modeling parameters on optimization are pointed out.

Striz, Alfred G.↗

NASA NTRSDate not supplied

Improved Heat Transfer Prediction for High-Speed Flows over Blunt Bodies using Adaptive Mixed-Element Unstructured Grids

Aerothermodynamic prediction is important for the design and analysis of many aerospace vehicles. Computational Fluid Dynamics (CFD) tools used for these predictions commonly rely on structured shock-aligned grids due to the strong shocks exhibited at high speeds. This work details the incorporation of an improved HLLE++ scheme for both perfect gas and thermochemical nonequilibrium flows which robustly captures shock waves on both non-shock-aligned and shock-aligned grids. The HLLE++ scheme reduces the impact of eigenvalue limiting on flow solutions which is required for Roe's scheme for high Mach number flows. An adapted grid approach is also demonstrated using mixed-element unstructured grids to improve heat prediction. Thin prismatic boundary layers are used with tetrahedra in the farfield and for capturing shock waves. Various results are presented for hypersonic flows over blunt bodies including cylinders, spheres, and capsules.

CFD↗

NASA NTRSDate not supplied

Improved Heat Transfer Prediction for High-Speed Flows over Blunt Bodies using Adaptive Mixed-Element Unstructured Grids

Aerothermodynamic prediction is important for the design and analysis of many aerospace vehicles. Computational Fluid Dynamics (CFD) tools used for these predictions commonly rely on structured shock-aligned grids due to the strong shocks exhibited at high speeds. This work details the incorporation of an improved HLLE++ scheme for both perfect gas and thermochemical nonequilibrium flows which robustly captures shock waves on both non-shock-aligned and shock-aligned grids. The HLLE++ scheme reduces the impact of eigenvalue limiting on flow solutions which is required for Roe's scheme for high Mach number flows. An adapted grid approach is also demonstrated using mixed-element unstructured grids to improve heat prediction. Thin prismatic boundary layers are used with tetrahedra in the farfield and for capturing shock waves. Various results are presented for hypersonic flows over blunt bodies including cylinders, spheres, and capsules.

CFD↗

NASA NTRS2020

Integrated Multi-satellite Evaluation for the Global Precipitation Measurement: Impact of Precipitation Types on Spaceborne Precipitation Estimation

An integrated multi-sensor assessment is proposed as a novel approach to advance satellite precipitation validation in order to provide users and algorithm developers with an assessment adequately coping with the varying performances of merged satellite precipitation estimates. Gridded precipitation rates retrieved from space sensors with quasi-global coverage feed numerous applications ranging from water budget studies to forecasting natural hazards caused by extreme events. Characterizing the error structure of satellite precipitation products is recognized as a major issue for the usefulness of these estimates. The Global Precipitation Measurement (GPM) mission aims at unifying precipitation measurements from a constellation of low-earth orbiting (LEO) sensors with various capabilities to detect, classify and quantify precipitation. They are used in combination with geostationary observations to provide gridded precipitation accumulations. The GPM Core Observatory satellite serves as a calibration reference for consistent precipitation retrieval algorithms across the constellation. The propagation of QPE uncertainty from LEO active/passive microwave (PMW) precipitation estimates to gridded QPE is addressed in this study, by focusing on the impact of precipitation typology on QPE from the Level-2 GPM Core Observatory Dual-frequency Precipitation Radar (DPR) to the Microwave Imager (GMI) to Level-3 IMERG precipitation over the Conterminous U.S. A high-resolution surface precipitation used as a consistent reference across scales is derived from the ground radar-based Multi-Radar/MultiSensor. While the error structure of the DPR, GMI and subsequent IMERG is complex because of the interaction of various error factors, systematic biases related to precipitation typology are consistently quantified across products. These biases display similar features across Level-2 and Level-3, highlighting the need to better resolve precipitation typology from space and the room for improvement in globalscale precipitation estimates. The integrated analysis and framework proposed herein applies more generally to precipitation estimates from sensors and error sources affecting low-earth orbiting satellites and derived gridded products.

Pierre-Emmanuel Kirstette↗

NASA NTRS2014

Numerical Analysis of a Rotating Detonation Engine in the Relative Reference Frame

A two-dimensional, computational fluid dynamic (CFD) simulation of a semi-idealized rotating detonation engine (RDE) is described. The simulation operates in the detonation frame of reference and utilizes a relatively coarse grid such that only the essential primary flow field structure is captured. This construction yields rapidly converging, steady solutions. Results from the simulation are compared to those from a more complex and refined code, and found to be in reasonable agreement. The performance impacts of several RDE design parameters are then examined. Finally, for a particular RDE configuration, it is found that direct performance comparison can be made with a straight-tube pulse detonation engine (PDE). Results show that they are essentially equivalent.

pulse detonation engines↗

NASA NTRS2014

Numerical Analysis of a Rotating Detonation Engine in the Relative Reference Frame

A two-dimensional, computational fluid dynamic (CFD) simulation of a semi-idealized rotating detonation engine (RDE) is described. The simulation operates in the detonation frame of reference and utilizes a relatively coarse grid such that only the essential primary flow field structure is captured. This construction yields rapidly converging, steady solutions. Results from the simulation are compared to those from a more complex and refined code, and found to be in reasonable agreement. The performance impacts of several RDE design parameters are then examined. Finally, for a particular RDE configuration, it is found that direct performance comparison can be made with a straight-tube pulse detonation engine (PDE). Results show that they are essentially equivalent.

propulsion↗

NASA NTRS2019

Integrated Multi-Satellite Evaluation for the Global Precipitation Measurement: Impact of Precipitation Types on Spaceborne Precipitation Estimation

Integrated multi-sensor assessment is proposed as a novel approach to advance satellite precipitation validation in order to provide users and algorithm developers with an assessment adequately coping with the varying performances of merged satellite precipitation estimates. Gridded precipitation rates retrieved from space sensors with quasi-global coverage feed numerous applications ranging from water budget studies to forecasting natural hazards caused by extreme events. Characterizing the error structure of satellite precipitation products is recognized as a major issue for the usefulness of these estimates. The Global Precipitation Measurement (GPM) mission aims at unifying precipitation measurements from a constellation of low-earth orbiting (LEO) sensors with various capabilities to detect, classify and quantify precipitation. They are used in combination with geostationary observations to provide gridded precipitation accumulations. The GPM Core Observatory satellite serves as a calibration reference for consistent precipitation retrieval algorithms across the constellation. The propagation of QPE uncertainty from LEO active/passive microwave (PMW) precipitation estimates to gridded QPE is addressed in this study, by focusing on the impact of precipitation typology on QPE from the Level-2 GPM Core Observatory Dual-frequency Precipitation Radar (DPR) to the Microwave Imager (GMI) to Level-3 IMERG precipitation over the Conterminous U.S. A high-resolution surface precipitation used as a consistent reference across scales is derived from the ground radar-based Multi-Radar/Multi-Sensor. While the error structure of the DPR, GMI and subsequent IMERG is complex because of the interaction of various error factors, systematic biases related to precipitation typology are consistently quantified across products. These biases display similar features across Level-2 and Level-3, highlighting the need to better resolve precipitation typology from space and the room for improvement in global-scale precipitation estimates. The integrated analysis and framework proposed herein applies more generally to precipitation estimates from sensors and error sources affecting low-earth orbiting satellites and derived gridded products.

Rainfall↗

NASA NTRSDate not supplied

Uncertainty Quantification of CFD Model Assumptions Against Sonic Boom Noise Prediction of a Commercial Supersonic Transport

This paper presents the results of uncertainty modeling of sonic boom noise generation from commercial supersonic transport considering the Spalart-Allmaras (SA) turbulence modeling parameters as well as Mach number, angle of attack and altitude. Sample generation and analysis for this uncertainty model was performed by UQPCE, which is a software package developed at the NASA Langley Research Center. To build the uncertainty model, 42 cases of sonic boom noise calculation were performed. Computation of the ground noise can be briefly summarized in two steps. First, the near field pressure waveforms are sampled from CFD calculation using the NASA Langley’s FUN3D solver. Second, this information is passed to an atmospheric propagation code, sBOOM, which solves an augmented Burger’s equation and simulates how the near field waveforms will change while passing through the atmosphere. The ground signature is further processed to obtain the perceived loudness, PLdB. Having a high spatial resolution near the shockwave in the CFD calculation is critical in sonic boom noise prediction. Because the variation in the input parameters for the current uncertainty quantification (UQ) study is likely to lead to change in shock location, angle and strength, the grid adaptation for shock capturing is independently applied for each condition. The final mesh used in the CFD calculation consists of approximately 420 million cells. The pressure signatures are sampled at three, four and five body lengths away from the aircraft to make sure the three dimensional effects around the aircraft are resolved. The results of the UQ analysis shows that within the three aleatory variables, the angle of attack had the most impact against ground noise, followed by the altitude and the Mach number. Between the two SA model parameters, the Kármán constant (𝜅) was significantly more important than the turbulent Prandtl number (𝜎), but these two parameters were only marginally significant in the overall prediction variance in ground noise. The UQ procedure explained in this paper can be widely applied to other model parameters.

Uncertainty Quantification↗

NASA NTRSDate not supplied

Uncertainty Quantification of CFD Model Assumptions Against Sonic Boom Noise Prediction of a Commercial Supersonic Transport

This paper presents the results of uncertainty modeling of sonic boom noise generation from commercial supersonic transport considering the Spalart-Allmaras (SA) turbulence modeling parameters as well as Mach number, angle of attack and altitude. Sample generation and analysis for this uncertainty model was performed by UQPCE, which is a software package developed at the NASA Langley Research Center. To build the uncertainty model, 42 cases of sonic boom noise calculation were performed. Computation of the ground noise can be briefly summarized in two steps. First, the near field pressure waveforms are sampled from CFD calculation using the NASA Langley’s FUN3D solver. Second, this information is passed to an atmospheric propagation code, sBOOM, which solves an augmented Burger’s equation and simulates how the near field waveforms will change while passing through the atmosphere. The ground signature is further processed to obtain the perceived loudness, PLdB. Having a high spatial resolution near the shock wave in the CFD calculation is critical in sonic boom noise prediction. Because the variation in the input parameters for the current uncertainty quantification (UQ) study is likely to lead to change in shock location, angle and strength, the grid adaptation for shock capturing is independently applied for each condition. The final mesh used in the CFD calculation consists of approximately 420 million cells. The pressure signatures are sampled at three, four and five body lengths away from the aircraft to make sure the three dimensional effects around the aircraft are resolved. The results of the UQ analysis shows that within the three aleatory variables, the angle of attack had the most impact against ground noise, followed by the altitude and the Mach number. Between the two SA model parameters, the Kármán constant (𝜅) was significantly more important than the turbulent Prandtl number (𝜎), but these two parameters were only marginally significant in the overall prediction variance in ground noise. The UQ procedure explained in this paper can be widely applied to other model parameters.

Uncertainty Quantifications↗

NASA NTRS2020

Building a standardized Observing System Simulation Experiment (OSSE) framework for Mars

We advocate that the Decadal Survey recommends the NASA Science Mission Directorate to develop a rigorous Observing System Simulation Experiment (OSSE) framework for Mars, to optimize future atmospheric observations. Atmospheric conditions on Mars are a potential hazard source for landing missions. Errors in the estimates of atmospheric density profiles, inadequate knowledge of wind vertical structure and dust concentration as a function of height are likely causes of uncertainty at the landing site on the order of kilometers. An operational real-time weather forecasting capability for Mars would reduce such uncertainties, carrying enormous benefits to future robotic missions, and would be an invaluable prerequisite for human missions.A real-time forecasting capability relies upon three fundamental components: a critical mass of observing systems, a data assimilation system (DAS), and a global forecast model. The DAS allows the model to ingest the data effectively, optimizing the observational information content,and transforming them into a gridded representation of the atmosphere at a given time, called an ‘analysis’. The analysis is the best estimate of the atmospheric state for that time, and also represents a set of ‘initial conditions’ from which a global model can be initialized, to predict a future state of the atmosphere. The connection between analysis and forecast represents the foundation of modern weather forecasting. However, from the point of view of a forecast system,not all observations are equally impactful, partially because of the problem of “observational error correlation”, one important research topic in data assimilation development. For the Earth, partly due to the spontaneous and deregulated development of observations and forecast capabilities worldwide for more than half a century,the use of observations in contemporary operational forecast systems is suboptimal, with many potentially useful data being underutilized. On the contrary, Mars atmospheric scientists are in the unique situation of designing the next-generation observing systems by learning from the experience gathered on the Earth, so as to assure that the future instruments are specifically optimized to give the maximum benefit to a future weather forecast capability.An immensely powerful tool that has been firmly established by atmospheric scientists on the Earth is represented by a properly designed OSSE framework. A realistic OSSE framework cannot only quantify the benefit of future data types, be them surface based or space borne, but can also help design and optimize an entire observational network. Furthermore, OSSEs can provide deep insights into an atmosphere’s behavior, by addressing conceptual problems of its intrinsic predictability and delineating the regions or features of the atmosphere which are more sensitive to additional data and would benefit from a denser sampling. The difficulties posed by OSSEs are fundamentally different for Earth and Mars. For Earth, the enormous data volume imposes a tremendous constraint on any innovation in the observing systems: it is very hard for a single sensor to impact the skill. For Mars, the problem is the opposite: almost any additional instrument will exert some impact. However, OSSEs can help to evaluate the cost/benefit for every sensor and suggest optimal data configuration and density.The purpose of this white paper is to provide an introduction to a rigorously designed OSSE framework, explain the underlying problems and challenges, and engage the Mars community to collaborate with Earth Atmospheric scientists in order to develop a joint-OSSE framework for Mars with the largest consensual basis possible. An OSSE infrastructure would increase the understanding of the Martian atmosphere, would help NASA to optimize instrument specifications and orbit choice, providing the maximium benefit for a given expenditure of resources, and could even help establishing a roadmap for a future real-time weather forecasting capability.

Oreste Reale↗

NASA NTRS1999

Regional Climate Simulation Experiments with a Variable Resolution Stretched Grid GCM

The variable resolution stretched grid (SG) version of the Goddard Earth Observing System (GEOS) GCM has been recently developed and tested in a regional climate simulation mode. The SG-approach is an alternative to the widely used nested grid approach introduced a decade ago as a pioneering step to regional climate modeling. The region of interest with a uniform about 60 km resolution used in experiments is a rectangle over the U.S. The results of one annual as well as two-month simulations for the anomalous climate event of the U.S. drought of 1988, are validated against data analysis fields and diagnostics. The efficient regional down-scaling as well as the positive impact of fine regional resolution, are obtained. The SG-concept appeared to be a promising candidate for regional and subregional climate studies and applications.

Takacs, Lawrence L.↗

NASA NTRS2013

Development of an Aeroelastic Modeling Capability for Transient Nozzle Side Load Analysis

Lateral nozzle forces are known to cause severe structural damage to any new rocket engine in development. Currently there is no fully coupled computational tool to analyze this fluid/structure interaction process. The objective of this study was to develop a fully coupled aeroelastic modeling capability to describe the fluid/structure interaction process during the transient nozzle operations. The aeroelastic model composes of three components: the computational fluid dynamics component based on an unstructured-grid, pressure-based computational fluid dynamics formulation, the computational structural dynamics component developed in the framework of modal analysis, and the fluid-structural interface component. The developed aeroelastic model was applied to the transient nozzle startup process of the Space Shuttle Main Engine at sea level. The computed nozzle side loads and the axial nozzle wall pressure profiles from the aeroelastic nozzle are compared with those of the published rigid nozzle results, and the impact of the fluid/structure interaction on nozzle side loads is interrogated and presented.

Wang, Ten-See↗

NASA NTRS1986

Analysis of coaxial spray combustion flames and related numerical issues

An approach to the simulation of strongly coupled multiphase flows in combustion hardware is sketched and its unique requirements highlighted. An example of a successful application to a coaxial injector flame is presented. Furthermore, several numerical issues that tend to interact with the physics of the problem are discussed with special regard to their potential impact on the choices of numerical parameters by the analyst. These include the issues of stability, numerical diffusivity, stiffness, and boundary conditions. The theme of this paper focuses on the intriguing relationships among the grid, the solution algorithm, and the actual physical mechanisms themselves.

Liang, P. Y.↗

NASA NTRS2015

Biomaterials Out of Thin Air: in Situ, On-Demand Printing of Advanced Biocomposites

Upmass is the single most significant limitation of our current space mission capability. Although biomaterials and biocomposites have mass, strength, flexibility, and self-healing properties that could significantly reduce upmass, their use is limited by the following drawbacks: Expensive, specific production. Many biomaterials can only be produced as part of significant support ecosystem; Inaccessible functional customization. The grain of wood, the porosity of bone, and so on are an integral part of the materials' desired mechanical properties, but are not deterministic when the material is naturally grown; Limited compositions. Most biomaterials (unlike metal, plastic, etc.) cannot be easily combined or modified to produce new materials. This project builds on recent advances in: Synthetic biology. Libraries of standardized genetic parts which can be used for controlled cellular material production, delivery, and binding; 3D printing. Commercial off-the-shelf components which can be used to make of a pico- to nanoliter cell deposition system; Tissue engineering. Proven cell-compatible support hydrogels and scaffolds can be modified to bind the deposited biomaterials of interest. Objectives: Feasibility and benefit analysis. Two mission contexts span the concept's scope (see below); Proof-of-concept demonstration. A simple grid of two proteins, fluorescent for easy detection, to validate the core technology concept; Proposed implementations for follow-on work. Avenues for future work on each core component (host cell, production control, material delivery, material binding, etc.); Complementary studies exploration. A survey of other emerging areas (in situ resource utilization, protein engineering, etc.) with the potential to multiply our technology's impact. Potential Impacts: This application could dramatically expand manufacturing capabilities on Earth and in space: In situ resource utilization. A far greater range of materials and products will be available from the limited palette offered by in situ resource extraction techniques; Reduced equipment and material upmass for off-Earth habitats. Ready- to-use highly specialized construction materials (radiation hardened, compressive/tensile, light or dense) from an extremely low starting mass; Structured biomaterial production. New ready-to-use macro, micro, and molecular manufacturing techniques for traditional biomaterials such as wood, bone and shell; New and novel biocomposite creation. The ability to create completely novel material composites from any base material that cells can be engineered to produce. Suggested Mission Contexts: ISS part manufacturing. A 'minimal working example' making a finished biomaterial part aboard the International Space Station; A long-term Mars habitat. 'Cradle-to-grave' use at a hypothetical Mars habitat, covering everything from tools to construction materials. Alternate Abstract: Imagine being able to print anything from tools and composite building materials to food and human tissues. Imagine being on Mars with the ability to replace any broken part, whether it's a part of your spacesuit, your habitat, or your own body. We propose a technique that would allow just that. By printing 3D arrays of cells engineered to secrete the necessary materials, the abundant in situ resources of atmosphere and regolith become organic, inorganic, or organic-inorganic composite materials. Such materials include novel, biologically derived materials not previously possible to fabricate.

habitats↗

NASA NTRS2015

Biomaterials Out of Thin Air: in Situ, On-demand Printing of Advanced Biocomposites

Upmass is the single most significant limitation of our current space mission capability. Although biomaterials and biocomposites have mass, strength, flexibility, and self-healing properties that could significantly reduce upmass, their use is limited by the following drawbacks: Expensive, specific production. Many biomaterials can only be produced as part of significant support ecosystem; Inaccessible functional customization. The grain of wood, the porosity of bone, and so on are an integral part of the materials' desired mechanical properties, but are not deterministic when the material is naturally grown; Limited compositions. Most biomaterials (unlike metal, plastic, etc.) cannot be easily combined or modified to produce new materials. This project builds on recent advances in: Synthetic biology. Libraries of standardized genetic parts which can be used for controlled cellular material production, delivery, and binding; 3D printing. Commercial off-the-shelf components which can be used to make of a pico- to nanoliter cell deposition system; Tissue engineering. Proven cell-compatible support hydrogels and scaffolds can be modified to bind the deposited biomaterials of interest. Objectives: Feasibility and benefit analysis. Two mission contexts span the concept's scope (see below); Proof-of-concept demonstration. A simple grid of two proteins, fluorescent for easy detection, to validate the core technology concept; Proposed implementations for follow-on work. Avenues for future work on each core component (host cell, production control, material delivery, material binding, etc.); Complementary studies exploration. A survey of other emerging areas (in situ resource utilization, protein engineering, etc.) with the potential to multiply our technology's impact. Potential Impacts: This application could dramatically expand manufacturing capabilities on Earth and in space: In situ resource utilization. A far greater range of materials and products will be available from the limited palette offered by in situ resource extraction techniques; Reduced equipment and material upmass for off-Earth habitats. Ready- to-use highly specialized construction materials (radiation hardened, compressive/tensile, light or dense) from an extremely low starting mass; Structured biomaterial production. New ready-to-use macro, micro, and molecular manufacturing techniques for traditional biomaterials such as wood, bone and shell; New and novel biocomposite creation. The ability to create completely novel material composites from any base material that cells can be engineered to produce. Suggested Mission Contexts: ISS part manufacturing. A 'minimal working example' making a finished biomaterial part aboard the International Space Station; A long-term Mars habitat. 'Cradle-to-grave' use at a hypothetical Mars habitat, covering everything from tools to construction materials. Alternate Abstract: Imagine being able to print anything from tools and composite building materials to food and human tissues. Imagine being on Mars with the ability to replace any broken part, whether it's a part of your spacesuit, your habitat, or your own body. We propose a technique that would allow just that. By printing 3D arrays of cells engineered to secrete the necessary materials, the abundant in situ resources of atmosphere and regolith become organic, inorganic, or organic-inorganic composite materials. Such materials include novel, biologically derived materials not previously possible to fabricate.

habitats↗

NASA NTRS2002

Flutter Analysis of a Transonic Fan

This paper describes the calculation of flutter stability characteristics for a transonic forward swept fan configuration using a viscous aeroelastic analysis program. Unsteady Navier-Stokes equations are solved on a dynamically deforming, body fitted, grid to obtain the aeroelastic characteristics using the energy exchange method. The non-zero inter-blade phase angle is modeled using phase-lagged boundary conditions. Results obtained show good correlation with measurements. It is found that the location of shock and variation of shock strength strongly influenced stability. Also, outboard stations primarily contributed to stability characteristics. Results demonstrate that changes in blade shape impact the calculated aerodynamic damping, indicating importance of using accurate blade operating shape under centrifugal and steady aerodynamic loading for flutter prediction. It was found that the calculated aerodynamic damping was relatively insensitive to variation in natural frequency.

Srivastava, R.↗

NASA NTRS2012

Surface Temperature Data Analysis

Small global mean temperature changes may have significant to disastrous consequences for the Earth's climate if they persist for an extended period. Obtaining global means from local weather reports is hampered by the uneven spatial distribution of the reliably reporting weather stations. Methods had to be developed that minimize as far as possible the impact of that situation. This software is a method of combining temperature data of individual stations to obtain a global mean trend, overcoming/estimating the uncertainty introduced by the spatial and temporal gaps in the available data. Useful estimates were obtained by the introduction of a special grid, subdividing the Earth's surface into 8,000 equal-area boxes, using the existing data to create virtual stations at the center of each of these boxes, and combining temperature anomalies (after assessing the radius of high correlation) rather than temperatures.

Hansen, James↗

NASA NTRS2000

TRMM Surface Backscatter Measurements - Temporal and Spatial Analysis: Inter-Comparison with NSCAT

Global rainfall is the primary redistributor of earth's energy by the process of latent heat release. This forms the main driving force for the tropical circulation, which in turn impacts the global circulation .through transient events-such as El Nino. Hence, more precise and long-term time series of the rainfall and its variability is crucial to the understanding and prediction of the global climate and climate change. The Precipitation Radar (PR) abroad the US/Japan Tropical Rainfall Measuring Mission (TRMM) is the first radar ever launched into space that measures detailed vertical profiles of rain intensity over the tropics. One of the challenges in estimating rainfall from spaceborne radars is the presence of attenuation at frequencies, such as 14 GHz of the TRMM PR and future planned systems at this and higher frequencies. A common approach in current rainfall retrieval algorithms is to employed the path integrated attenuation (PIA) as a constraint to the retrieval, and hence overcome errors in the radar calibration or in the assumed rainfall parameters. PIA can either be derived from a radiometer or from the surface reference technique, in which a clear air radar measurement is compared with the measurement in the raining area. The current TRMM 2A21 PIA data product makes use of both a temporal and spatial clear air database for comparison to rainy measurements. In this paper we present results from analysis of TRMM surface backscatter cross-section (sigmaO) measurements from Nov 97-Feb99, and a comparison with sigmaO measurements obtained by the NASA Scatterometer (NSCAT) between Sept96-June97. Measurements for a given month from both instruments are compiled on a 1 deg. (lat.) x 1 deg. (lon.) x 1 hr. grid. This enables TRMM--NSCAT comparison and the investigation of seasonal and diurnal trends in both data sets. From preliminary analysis of TRMM sigmaO's we have decided not to treat the ocean as a single homogeneous region but to select a number of ocean sub-regions and individually analyze their trends. Likewise, and in a similar approach to previous studies of Seasat over-land data, we have selected a number of over-land regions for study. From said sigmaO maps and regional trend analysis we investigate possible sources of trends and variability. In addition, we study the effects of TRMM PR sensitivity through the PR "possible rain" class. Given NSCAT's inability to flag rain contaminated measurements we are able to gauge the impact of rain contamination on NSCAT monthly sigmaO maps, using TRMM measurements. The research described in this paper was carried out by the Jet Propulsion Laboratory, California Institute of Technology, under contract with the National Aeronautics and Space Administration (NASA), U.S.A.

Im, Eastwood↗