Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “gradient sensing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

RF Reference Switch for Spaceflight Radiometer Calibration

The goal of this technology is to provide improved calibration and measurement sensitivity to the Soil Moisture Active Passive Mission (SMAP) radiometer. While RF switches have been used in the past to calibrate microwave radiometers, the switch used on SMAP employs several techniques uniquely tailored to the instrument requirements and passive remote-sensing in general to improve radiometer performance. Measurement error and sensitivity are improved by employing techniques to reduce thermal gradients within the device, reduce insertion loss during antenna observations, increase insertion loss temporal stability, and increase rejection of radar and RFI (radio-frequency interference) signals during calibration. The two legs of the single-pole double-throw reference switch employ three PIN diodes per leg in a parallel-shunt configuration to minimize insertion loss and increase stability while exceeding rejection requirements at 1,413 MHz. The high-speed packaged diodes are selected to minimize junction capacitance and resistance while ensuring the parallel devices have very similar I-V curves. Switch rejection is improved by adding high-impedance quarter-wave tapers before and after the diodes, along with replacing the ground via of one diode per leg with an open circuit stub. Errors due to thermal gradients in the switch are reduced by embedding the 50-ohm reference load within the switch, along with using a 0.25-in. (approximately equal to 0.6-cm) aluminum prebacked substrate. Previous spaceflight microwave radiometers did not embed the reference load and thermocouple directly within the calibration switch. In doing so, the SMAP switch reduces error caused by thermal gradients between the load and switch. Thermal issues are further reduced by moving the custom, highspeed regulated driver circuit to a physically separate PWB (printed wiring board). Regarding RF performance, previous spaceflight reference switches have not employed high-impedance tapers to improve rejection. The use of open-circuit stubs instead of a via to provide an improved RF short is unique to this design. The stubs are easily tunable to provide high rejection at specific frequencies while maintaining very low insertion loss in-band.

Knuble, Joseph↗

Modeling Phenological Controls on Carbon Dynamics in Dryland Sagebrush Ecosystems

Dryland ecosystems play an important role in determining how precipitation anomalies affect terrestrial carbon fluxes at regional to global scales. Thus, to understand how climate change may affect the global carbon cycle, we must also be able to understand and model its effects on dryland vegetation. Dynamic Global Vegetation Models (DGVMs) are an important tool for modeling ecosystem dynamics, but they often struggle to reproduce seasonal patterns of plant productivity. Because the phenological niche of many plant species is linked to both total productivity and competitive interactions with other plants, errors in how process-based models represent phenology hinder our ability to predict climate change impacts. This may be particularly problematic in dryland ecosystems where many species have developed a complex phenology in response to seasonal variability in both moisture and temperature. Here, we examine how uncertainty in key parameters as well as the structure of existing phenology routines affect the ability of a DGVM to match seasonal patterns of leaf area index (LAI) and gross primary productivity (GPP) across a temperature and precipitation gradient. First, we optimized model parameters using a combination of site-level eddy covariance data and remotely-sensed LAI data. Second, we modified the model to include a semi-deciduous phenology type and added flexibility to the representation of grass phenology. While optimizing parameters reduced model bias, the largest gains in model performance were associated with the development of our new representation of phenology. This modified model was able to better capture seasonal patterns of both leaf area index (R(exp 2) = 0.75) and gross primary productivity (R(exp 2) = 0.84), though its ability to estimate total annual GPP depended on using eddy covariance data for optimization. The new model also resulted in a more realistic outcome of modeled competition between grass and shrubs. These findings demonstrate the importance of improving how DGVMs represent phenology in order to accurately forecast climate change impacts in dryland ecosystems.

Ecosystem model↗

The relative importance of aerosol scattering and absorption in remote sensing

The relative importance of aerosol optical thickness and absorption is illustrated through computing radiances for radiative transfer models. The radiance of sunlight reflected from models of the earth-atmosphere system is computed as a function of the aerosol optical thickness and its albedo of single scattering; it is noted that the albedo varies from 0.6 in urban environment to nearly 1 in areas with low graphitic carbon content. The calculations are applied to the example of satellite measurements of biomass. It is found that when surface classifications are made by means of clustering techniques the presence of gradients in the aerosol optical properties results in the dispersion of points in the plot correlating radiances viewed in two different directions. Finally, though such a remote sensing parameter as contrast is weakly affected by aerosol absorption, it is highly dependent on its optical thickness.

Fraser, R. S.↗

Structure and polarization of active region microwave emission

Active region radio emission observations made at 6.16 cm wavelength during May 20-27, 1980, are the bases of maps of total intensity and circular polarization presented for the three regions whose Hale numbers are 16850, 16863, and 16864. A detailed comparison is made between these maps and on- and off-band H-alpha pictures and magnetograms. The neutral lines with which the strongest sources were associated have their two opposite polarities close to each other, implying a high magnetic field gradient, and are also associated with arch filament systems. A detailed analysis is undertaken of observations of the circular polarization sense inversion in region 16863. The large scale structure of the magnetic field can be approximated by a dipole with its axis inclined by 11 deg with respect to the photosphere, and with a dipole moment of about 2 x 10 to the 31 power cgs units.

Kundu, M. R.↗

Applying Thermal Gradients To Control Vibrations

Thermal actuators used to stabilize large structures. New damping concept calls for application of suitably timed and shaped thermal-gradient waveforms to generate expansions and contractions counteracting vibrations. Responding to processed signal from accelerometer, thermoelectric heat pumps apply thermal gradients producing expansions and contractions in upper and lower caps of cantilever beam. These expansions and contractions partly counteract vibrations sensed by accelerometer, thus contributing to damping.

Edberg, Donald L.↗

The Pilot Land Data System (PLDS) at the Ames Research Center manages aircraft data in collaboration with an ecosystem research project

The Pilot Land Data System (PLDS) is a data and information system serving NASA-supported investigators in the land science community. The three nodes of the PLDS, one each at the Ames Research Center (ARC), the Goddard Space Flight Center (GSFC) and the Jet Propulsion Laboratory (JPL), cooperate in providing consistent information describing the various data holding in the hardware and software (accessible via network and modem) that provide information about and access to PLDS-held data, which is available for distribution. A major new activity of the PLDS node at the Ames Research Center involves the interaction of the PLDS with an active NASA ecosystem science project, the Oregon Transect Ecosystems Research involves the management of, access to, and distribution of the large volume of widely-varying aircraft data collected by OTTER. The OTTER project, is managed by researchers at the Ames Research Center and Oregon State University. Its principal objective is to estimate major fluxes of carbon, nitrogen, and water of forest ecosystems using an ecosystem process model driven by remote sensing data. Ten researchers at NASA centers and universities are analyzing data for six sites along a temperature-moisture gradient across the western half of central Oregon (called the Oregon Transect). Sensors mounted on six different aircraft have acquired data over the Oregon Transect in support of the OTTER project.

Angelici, Gary↗

SAYANI'91 - A joint United States/Commonwealth of Independent States field campaign to investigate forest decline damage in the Krasnoyarsk region of southcentral Siberia

The field experiment described took place in the Sayani Mountains of Siberia. The purpose of the joint field campaign was to observe and exchange methodologies with Russian scientists with regard to the development of remote sensing techniques for the early detection and assessment of forest decline damage believed to be associated with atmospheric deposition and/or insect and disease infestations. Several types of passive and active remote sensing measurements were made in conjunction with biophysical measurements on vegetative samples collected from four study sites representing a strong elevational gradient. Relatively cloud-free SPOT data were also acquired over the study area. Moderate canopy damage was recorded at the mid-elevation site (3400 ft/1037 m). The lowest levels of damage were recorded at the lowest elevation site (2300 ft/701 m.) At all sites, east versus west flagging of the canopy was noted (i.e., full canopy on the west-facing side of the canopy, significantly less foliage on the east-facing side).

Williams, D. L.↗

Model Simulations of Ozone in the Summer Lower Stratosphere

The Goddard 3D chemistry and transport model (CTM) uses winds and temperatures from the Goddard Earth Observing System Data Assimilation System (GEOS DAS); thus CTM simulations can be compared directly with observations from satellite, balloon and aircraft. In general, aspects of these comparisons show remarkable agreement between observation and model. One significant difference is that the model ozone is high biased below the ozone peak. The bias is apparently largest at high latitudes during the summer months. At the same time, comparisons with HALOE observations show that at mid to high latitudes, the ozone mixing ratio peak appears persistently at a lower altitude than observed by HALOE; the peak mixing ratio is also overestimated by the model. Both transport and photochemistry are possible contributors to the biased ozone in the lower stratosphere - excessive downward motion would increase lower stratospheric ozone, as would a too large vertical gradient in ozone. On the other hand, comparisons of model N2O and NOy with observations suggest transport deficiencies in the opposite sense, i.e., model N2O can be high relative to observations (particularly during winter), suggesting the need for stronger downward transport. Sensitivity studies have been carried out using parameterizations for ozone production and loss, NOy production and loss, and N2O loss. The goal of these studies is to clarify how problems in the photochemical scheme at and above the ozone peak influence the lower stratospheric ozone.

Douglass, Anne R.↗

The Regulation of Growth in the Distal Elongation Zone of Maize Roots

The major goals of the proposed research were 1. To develop specialized software for automated whole surface root expansion analysis and to develop technology for controlled placement of surface electrodes for analysis of relationships between root growth and root pH and electrophysiological properties. 2. To measure surface pH patterns and determine the possible role of proton flux in gravitropic sensing or response, and 3. To determine the role of auxin transport in establishment of patterns of proton flux and electrical gradients during the gravitropic response of roots with special emphasis on the role of the distal elongation zone in the early phases of the gravitropic response.

Evans, Michael L.↗

Complex physiological and molecular processes underlying root gravitropism

Gravitropism allows plant organs to guide their growth in relation to the gravity vector. For most roots, this response to gravity allows downward growth into soil where water and nutrients are available for plant growth and development. The primary site for gravity sensing in roots includes the root cap and appears to involve the sedimentation of amyloplasts within the columella cells. This process triggers a signal transduction pathway that promotes both an acidification of the wall around the columella cells, an alkalinization of the columella cytoplasm, and the development of a lateral polarity across the root cap that allows for the establishment of a lateral auxin gradient. This gradient is then transmitted to the elongation zones where it triggers a differential cellular elongation on opposite flanks of the central elongation zone, responsible for part of the gravitropic curvature. Recent findings also suggest the involvement of a secondary site/mechanism of gravity sensing for gravitropism in roots, and the possibility that the early phases of graviresponse, which involve differential elongation on opposite flanks of the distal elongation zone, might be independent of this auxin gradient. This review discusses our current understanding of the molecular and physiological mechanisms underlying these various phases of the gravitropic response in roots.

NASA Discipline Plant Biology↗

A model for microwave intensity propagation in an inhomogeneous medium

A combined analytic and phenomenological approach, utilizing Maxwell's equations in the Born approximation with radiative transfer theory, is used to describe the propagation of microwave intensity in a scattering medium characterized by three-dimensional random fluctuations in refractive index, as well as nonrandom variations in permittivity, temperature, and loss. This approach yields microwave intensities as a function of polarization, direction, and position. Numerical techniques are presented to solve the transport equations, which include cases of spatially varying coefficients, and highly peaked phase functions. Some computed results illustrating the behavior of microwave intensity in various media are presented. Included are the angular and frequency spectra of thermal emission from semi-infinite media, and the diffuse transmission and reflection response of a scattering layer. The effects of scatterer geometry and scale sizes; correlation function; and gradients in temperature, loss, and scattering parameters are also demonstrated. This model should be particularly useful in interpreting active and passive remote sensing data.

Fisher, A. D.↗

Optimization of linear, controlled structures

An approach to the integrated design of linear controlled structures, which is being investigated as part of NASA's controlled structures interaction (CSI) methodology development program, is presented. The approach is integrated in the sense that the structure and its controller are simultaneously designed. The design methodology uses constrained nonlinear optimization procedures based on analytically obtained gradients of the structural responses. Design of the controller is based on the so-called Q-parameterization theory, which parameterizes all closed-loop input/output maps achievable with stabiizing linear controllers. Very general objective and constraint functions are possible, and structural shape can be included in the design variables. This method has been partially implemented and demonstrated; early findings are reported.

Hunziker, K. Scott↗

Performance seeking control excitation mode

Flight testing of the performance seeking control (PSC) excitation mode was successfully completed at NASA Dryden on the F-15 highly integrated digital electronic control (HIDEC) aircraft. Although the excitation mode was not one of the original objectives of the PSC program, it was rapidly prototyped and implemented into the architecture of the PSC algorithm, allowing valuable and timely research data to be gathered. The primary flight test objective was to investigate the feasibility of a future measurement-based performance optimization algorithm. This future algorithm, called AdAPT, which stands for adaptive aircraft performance technology, generates and applies excitation inputs to selected control effectors. Fourier transformations are used to convert measured response and control effector data into frequency domain models which are mapped into state space models using multiterm frequency matching. Formal optimization principles are applied to produce an integrated, performance optimal effector suite. The key technical challenge of the measurement-based approach is the identification of the gradient of the performance index to the selected control effector. This concern was addressed by the excitation mode flight test. The AdAPT feasibility study utilized the PSC excitation mode to apply separate sinusoidal excitation trims to the controls - one aircraft, inlet first ramp (cowl), and one engine, throat area. Aircraft control and response data were recorded using on-board instrumentation and analyzed post-flight. Sensor noise characteristics, axial acceleration performance gradients, and repeatability were determined. Results were compared to pilot comments to assess the ride quality. Flight test results indicate that performance gradients were identified at all flight conditions, sensor noise levels were acceptable at the frequencies of interest, and excitations were generally not sensed by the pilot.

Schkolnik, Gerard↗

Profiles of Reactive Trace Gases over Remote Oceans During ATom

The Atmospheric Tomography (ATom) mission deployed an extensive gas and aerosol payload on the NASA DC-8 aircraft on four campaigns spanning each season. ATom systematically sampled the atmosphere from 0.2 to 12 kilometer altitude, from 85 degrees North Latitude to 65 degrees South Latitude, in both the Pacific and the Atlantic to provide detailed profiles of chemical composition over the remote oceans. We will present profiles of reactive trace species, such as O3, NOx, NOy, HOx, HCHO, and several other short-lived source gases. We will combine these measurements with results from a 0-D box model to show their utility in (1) evaluating gradients in latitude/season, (2) identifying contributions of pollution from long-range and convective transport, and (3) evaluating column measurements from remote sensing satellite instruments.

ISAF↗

Validation and Application of Satellite-Derived Sea Surface Temperature Gradients in the Bering Strait and Bering Sea

The Arctic is one of the most important regions in the world’s oceans for understanding the impacts of a changing climate. Yet, it is also difficult to measure because of extreme weather and ice conditions. In this work, we directly compare four datasets from the Group for High-Resolution Sea Surface Temperature (GHRSST) with a NASA Saildrone deployment along the Alaskan Coast and the Bering Sea and Bering Strait. The four datasets used are the Remote Sensing Systems Microwave Infrared Optimally Interpolated (MWIR) product, the Canadian Meteorological Center (CMC) product, the Daily Optimally Interpolated Product (DOISST), and the Operational Sea Surface Temperature and Ice Analysis (OSTIA) product. Spatial sea surface temperature (SST) gradients were derived for both the Saildrone deployment and GHRSST products, with the GHRSST products collocated with the Saildrone deployment. Overall, statistics indicate that the OSTIA product had a correlation of 0.79 and a root mean square difference of 0.11 °C/km when compared with Saildrone. CMC had the highest correlation of 0.81. Scatter plots indicate that OSTIA had the slope closest to one, thus best reproducing the magnitudes of the Saildrone gradients. Differences increased at latitudes > 65°N where sea ice would have a greater impact. A trend analysis was then performed on the gradient fields. Overall, positive trends in gradients occurred in areas along the coastal regions. A negative trend occurred at approximately 60°N. A major finding of this study is that future work needs to revolve around the impact of changing ice conditions on SST gradients. Another major finding is that a northward shift in the southern ice edge occurred after 2010 with a maxima at approximately 2019. This indicates that the shift of the southern ice edge is not gradual but has dramatically increased over the last decade. Future work needs to revolve around examining the possible causes for this northward shift.

Arctic↗

Recent advancement of turbulent flow measurement techniques

Advancements of the fluctuating density gradient cross beam laser Schlieren technique, the fluctuating line-reversal temperature measurement and the development of the two-dimensional drag-sensing probe to a three-dimensional drag-sensing probe are discussed. The three-dimensionality of the instantaneous momentum vector can shed some light on the nature of turbulence especially with swirling flow. All three measured fluctuating quantities (density, temperature, and momentum) can provide valuable information for theoreticians.

Battle, T.↗

Structure and length scales of rotational discontinuities

Results are presented of a series of 1D hybrid (kinetic ions and fluid electrons) simulations, using a nondynamic method to form rotational discontinuities (RDs) at an angle of 60 deg between the normal direction and the upstream magnetic field. Ion kinetic effects are found to be important with regard to the stability of the current layer, its thickness and scaling, and its dependence on initial conditions. A detailed examination of the downstream wave train and gradient scale size showed that RDs with alpha1 = +/-180 deg are stable within the framework of the simulation. With proper initialization, electron-sense rotations of -270 deg were found that do not disintegrate immediately but rather appear to consist of a superposition of a solitary wave with -360-deg rotation and a 90-deg ion-sense rotation.

Krauss-Varban, D.↗

Oregon transect: Comparison of leaf-level reflectance with canopy-level and modelled reflectance

The Oregon Transect Ecosystem Research (OTTER) project involves the collection of a variety of remotely-sensed and in situ measurements for characterization of forest biophysical and biochemical parameters. The project includes nine study plots located along an environmental gradient in west-central Oregon, extending from the Pacific coast inland approximately 300km. These plots represent a broad range in ecosystem structure and function. Within the OTTER project, the sensitivity of the Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) signal to absorption by foliar biochemicals is being examined. AVIRIS data were acquired over all plots in conjunction with the four OTTER Multi-sensor Aircraft Campaigns spanning the growing season. Foilage samples were gathered during each campaign for biochemical determination (at Ames Research Center), to estimate stand-level constituency at each plot. Directional-hemispheric leaf reflectance throughout the 400-2400nm region was measured in the laboratory as an aid to interpreting concurrent AVIRIS data. Obtaining leaf spectra in this manner reduces or eliminates the confounding influences of atmosphere, canopy architecture, and reflectance by woody components, understory, and exposed soils which are present in airborne observations. These laboratory spectra were compared to simulated spectra derived by inverting the PROSPECT leaf-level canopy reflectance derived from AVIRIS data by use of the LOWTRAN-7 atmospheric radiative-transfer model.

Johnson, Lee F.↗