Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fuzzing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

96 records · Page 6

Characterizing the recovery of a solid surface after tungsten nano-tendril formation

Here, recovery of a flat tungsten surface from a nano-tendril surface is attempted through three techniques; a mechanical wipe, a 1673 K annealing, and laser-induced thermal transients. Results were determined through SEM imaging and elastic recoil detection to assess the helium content in the surface. The mechanical wipe leaves a ~0.5 μm deep layer of nano-tendrils on the surface post-wipe regardless of the initial nano-tendril layer depth. Laser-induced thermal transients only significantly impact the surface morphology at heat loads of 35.2 MJ/m 2 s 1/2 or above, however a fully flat or recovered surface was not achieved for 100 transients at this heat load despite reducing the helium content by a factor of ~7. A 1673 K annealing removes all detectable levels of helium but sub-surface voids/bubbles remain intact. The surface is recovered to a nearly flat state with only some remnants of nano-tendrils re-integrating into the surface remaining.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Helium flux effects on bubble growth and surface morphology in plasma-facing tungsten from large-scale molecular dynamics simulations

We investigate helium flux effects on helium transport and surface evolution in plasma-facing tungsten using molecular dynamics. The simulations span two orders of magnitude, from ITER-relevant levels to those more typical of simulations published to date. Simulation times of up to 2.5 µs (corresponding to actual fluences of 1.4 x 10 21 m -2 ) are achieved, revealing concerted bubble-bursting events that are responsible for significant and very sudden changes in surface morphology. The depth distribution of helium depends very strongly on helium flux: helium self-trapping becomes more probable near the surface at high flux, and a layer of near-surface bubbles forms. Helium retention prior to the onset of bubble bursting is also substantially lower at low flux than it is at high flux. Surface features at low fluence are correlated with the positions of bubbles, but at high fluence, bubbles tend to coalesce, venting to the surface at one or more locations and leaving large interconnected cavities below the surface. Ruptured bubbles may serve as pathways deeper into the material, allowing helium to bypass the layer of near-surface bubbles and fill deeper, potentially much larger, bubbles that can produce more substantial surface features. Deeper bubbles also emit prismatic dislocation loops that can fill in cavities closer to the surface. Our results suggest that nearly all molecular dynamics simulations published to date are hampered by finite-size effects, and that helium flux is a very important parameter in determining the behavior of helium in plasma-facing components.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Corrigendum and Addendum: Helium flux effects on bubble growth and surface morphology in plasma-facing tungsten from large-scale molecular dynamics simulations (2019 Nucl. Fusion 59 066035)

Two of the simulations discussed in a prior article (Hammond et al 2019 Nucl. Fusion 59 066035) were affected by a simulation glitch. We repeated the affected calculations and discuss them here. Here, the overall conclusions are essentially unchanged, though the details are different. In particular, observations that we referred to as ‘concerted bursting’ were caused primarily by non-physical heating and cooling applied by the thermostat after most atoms’ velocities were deleted (for reasons that are not known for certain). The phenomenon of one bubble bursting and causing another nearby bubble to burst does exist, though its effects are much less spectacular in the absence of non-physical driving forces. The observation of an interconnected network of sub-surface cavities formed by burst bubbles is real, and the observation of holes on the surface 1–2 nm in diameter is also confirmed.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Helium bubble size effects on the surface morphological response of plasma-facing tungsten

Abstract We report a simulation study on the effects of helium (He) bubble size on the morphological evolution and pattern formation on the surface of tungsten used as a plasma-facing component (PFC) in nuclear fusion devices. We have carried out a systematic investigation based on self-consistent dynamical simulations of surface morphological evolution according to an atomistically-informed, 3D continuum-scale model that captures well the relevant length and time scales of surface nanostructure formation in PFC tungsten. The model accounts for PFC surface diffusion, driven by the biaxial compressive stress originating from the over-pressurized He bubbles in the near-surface region of PFC tungsten as a result of He plasma exposure, combined with the formation of self-interstitial atoms in tungsten that diffuse toward the PFC surface and the flux of surface adatoms generated as a result of surface vacancy-adatom pair formation upon He implantation; this transport of surface adatoms contributes to the anisotropic growth of surface nanostructural features due to the different rates of adatom diffusion along and across step edges of islands on the tungsten surface. Our detailed analysis reveals that varying the average He bubble size plays an important role in the PFC surface growth kinetics as well as the resulting surface topography. Specifically, we find that an increase in the He bubble size leads to a deceleration in the growth rate of the tungsten nanotendrils that emanate from the PFC surface. We also find that the separation distance between the resulting surface features increases with increasing He bubble size, as well as over time. This coarsening effect is a thermally activated process resulting in an accurate description of the temperature dependence of the average surface feature separation by an Arrhenius relation.

36 MATERIALS SCIENCE↗