SEARCH · Engineering Papers

Results for “flow field”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

NASA NTRS2004

Synthetic Jet Flow Field Database for CFD Validation

An oscillatory zero net mass flow jet was generated by a cavity-pumping device, namely a synthetic jet actuator. This basic oscillating jet flow field was selected as the first of the three test cases for the Langley workshop on CFD Validation of Synthetic Jets and Turbulent Separation Control. The purpose of this workshop was to assess the current CFD capabilities to predict unsteady flow fields of synthetic jets and separation control. This paper describes the characteristics and flow field database of a synthetic jet in a quiescent fluid. In this experiment, Particle Image Velocimetry (PIV), Laser Doppler Velocimetry (LDV), and hot-wire anemometry were used to measure the jet velocity field. In addition, the actuator operating parameters including diaphragm displacement, internal cavity pressure, and internal cavity temperature were also documented to provide boundary conditions for CFD modeling.

Yao, Chung-Sheng↗

NASA NTRS2009

Large Eddy Simulation of Transonic Flow Field in NASA Rotor 37

The current paper reports on numerical investigations on the flow characteristics in a transonic axial compressor, NASA Rotor 37. The flow field was used previously as a CFD blind test case conducted by American Society of Mechanical Engineers in 1994. Since the CFD blind-test exercise, many numerical studies on the flow field in the NASA Rotor 37 have been reported. Although steady improvements have been reported in both numerical procedure and turbulence closure, it is believed that all the important aspects of the flow field have not been fully explained with numerical studies based on the Reynolds Averaged Navier-Stokes (RANS) solution. Experimental data show large dip in total pressure distribution near the hub at downstream of the rotor at 100% rotor speed. Most original numerical solutions from the blind test exercise did not predict this total pressure deficit correctly. This total pressure deficit at the rotor exit was attributed to a hub corner flow separation by the author. Several subsequent numerical studies with different turbulence closure model also calculated this dip in total pressure rise. Also, several studies attributed this total pressure deficit to a small leakage flow coming from the hub in the test article. As the experimental study cannot be repeated, either explanation cannot be validated. The primary purpose of the current investigation is to investigate the transonic flow field with both RANS and a Large Eddy Simulation (LES). The RANS approach gives similar results presented at the original blind test exercise. Although the RANS calculates higher overall total pressure rise, the total pressure deficit near the hub is calculated correctly. The numerical solution shows that the total pressure deficit is due to a hub corner flow separation. The calculated pressure rise from the LES agrees better with the measured total pressure rise especially near the casing area where the passage shock interacts with the tip clearance vortex and flow becomes unsteady due to this interaction. The LES simulation also calculates the total pressure rise deficit near the hub and it agrees well with the measured data.

Hah, Chunill↗

NASA NTRS1979

Calculation of the three-dimensional flow field in supersonic inlets at angle of attack using a bicharacteristic method with discrete shock wave fitting

An analysis is presented for calculating the flow field in supersonic mixed-compression aircraft inlets operating at angle of attack. The flow field is computed by a steady three-dimensional bicharacteristic method. The bow shock wave and the reflected internal shock wave system are computed by a three-dimensional discrete shock wave fitting procedure. Viscous and thermal diffusion may be included as source terms in the bicharacteristic method. A production type computer program capable of determining the flow field in a variety of axisymmetric mixed-compression supersonic inlets is available. The results of the present analysis agree well with those produced by the two-dimensional method of characteristics when axisymmetric flow fields are computed. For three-dimensional flow fields, the results of the present analysis agree well with experimental data except in regions of high viscous interaction and boundary layer removal. The present analysis does not compute the boundary layer, nor does it account for boundary layer bleed.

Vadyak, J.↗

NASA NTRS2016

Comparison of Experimental Surface and Flow Field Measurements to Computational Results of the Juncture Flow Model

Wing-body juncture flow fields on commercial aircraft configurations are challenging to compute accurately. The NASA Advanced Air Vehicle Program's juncture flow committee is designing an experiment to provide data to improve Computational Fluid Dynamics (CFD) modeling in the juncture flow region. Preliminary design of the model was done using CFD, yet CFD tends to over-predict the separation in the juncture flow region. Risk reduction wind tunnel tests were requisitioned by the committee to obtain a better understanding of the flow characteristics of the designed models. NASA Ames Research Center's Fluid Mechanics Lab performed one of the risk reduction tests. The results of one case, accompanied by CFD simulations, are presented in this paper. Experimental results suggest the wall mounted wind tunnel model produces a thicker boundary layer on the fuselage than the CFD predictions, resulting in a larger wing horseshoe vortex suppressing the side of body separation in the juncture flow region. Compared to experimental results, CFD predicts a thinner boundary layer on the fuselage generates a weaker wing horseshoe vortex resulting in a larger side of body separation.

Roozeboom, Nettie H.↗

NASA NTRS2016

Comparison of Experimental Surface and Flow Field Measurements to Computational Results of the Juncture Flow Model

Roozeboom, Nettie H.↗

NASA NTRS1982

An experimental investigation of circulation control flow fields using holographic interferometry

Experiments are presented which were conducted on flow fields produced by a circulation control airfoil utilizing the Coanda effect at the trailing edge. The application of holographic interferometry to obtain both visualization and quantitative data on the flow field about a circulation control airfoil at transonic flow speed is covered. A brief description of the flow model and measurement techniques is given. The data reduction procedure, results, and interpretation are presented. The results have provided a good deal of information on the character of the flow field, particularly in the neighborhood of the trailing edge. As to the airfoil design, it is apparent that improved performance can be achieved if jet detachment is delayed. Another design improvement would involve the development of an optimum trailing-edge shape for the expected operating Mach and Reynolds number ranges.

Bachalo, William D.↗

NASA NTRS1987

A zonal method for modeling 3-D aircraft flow fields with jet plume effects

A coupled zonal method has been developed for modeling flows about aircraft with highly integrated advanced nozzle installations in which the exhaust plume interacts with the aircraft flow field to enhance performance. A cost effective flow analysis is achieved by dividing the flow domain into zones and coupling the zonal solutions. PAN AIR is used to model the flow in the inviscid zone which surrounds the aircraft. The plume zone flow field is solved with a PNS code. The flow in the optional internal nozzle zone is modeled using a full Navier-Stokes code. An automated iterative procedure couples the inviscid and plume zones by passing updated boundary conditions between the zones. The coupled analysis provides converged solutions for the overall flow field. The method is demonstrated for a highly integrated nonaxisymmetric vectored nozzle installed on a swept-wing aircraft.

Roberts, D. W.↗

NASA NTRS2000

Development of Dynamic Flow Field Pressure Probes Suitable for Use in Large Scale Supersonic Wind Tunnels

A series of dynamic flow field pressure probes were developed for use in large-scale supersonic wind tunnels at NASA Glenn Research Center. These flow field probes include pitot, static, and five-hole conical pressure probes that are capable of capturing fast acting flow field pressure transients that occur on a millisecond time scale. The pitot and static probes can be used to determine local Mach number time histories during a transient event. The five-hole conical pressure probes are used primarily to determine local flow angularity, but can also determine local Mach number. These probes were designed, developed, and tested at the NASA Glenn Research Center. They were also used in a NASA Glenn 10-by 10-Foot Supersonic Wind Tunnel (SWT) test program where they successfully acquired flow field pressure data in the vicinity of a propulsion system during an engine compressor staff and inlet unstart transient event. Details of the design, development, and subsequent use of these probes are discussed in this report.

Porro, A. Robert↗

NASA NTRS1990

Experimental Investigation of Porous-floor Effects on Cavity Flow Fields at Supersonic Speeds

An experimental investigation was conducted to determine the effectiveness of a passive-venting system to modify the flow field characteristics of a rectangular-box cavity at supersonic speeds. The passive-venting system consists of a porous floor with a vent chamber beneath the floor. For certain cavity length-to-height ratios, this configuration allowed high-pressure air at the rear of the cavity to vent to the forward part of the cavity, thereby modifying the cavity flow field. The wind-tunnel model consisted of a flat plate that housed a cavity mounted on a balance such that only the cavity drag was measured. The cavity height remained constant, and the length varied with rectangular-block inserts. Both solid-and porous-floor cavities were tested for comparison at Mach numbers of 1.60, 1.90, 2.16, and 2.86. These results showed that the passive-venting system did modify the cavity flow field. In order to determine the type flow field which existed for the porous-floor configuration, pressures were measured inside the cavity at the same conditions and for the same configurations as those used in the drag tests. Pressure data were also obtained with stores mounted in the cavity. These results, along with Schlieren photographs and the tabulated data, are presented to document the porous-floor cavity flow field.

Wilcox, Floyd J., Jr.↗

NASA NTRS1967

Radial static pressure distributions in confined compressible vortex flow fields

Effects of fluid mass flow rate and exit orifice diameter on radial static pressure distribution in compressible vortex flow field

VORTEX FLOW↗

NASA NTRS1988

Overlapping grids for flow field calculations

Many problems in computational fluid dynamics (CFD) involve the calculation of flow fields within or around complex geometric configurations. The flow solution is computed on a computational grid. The construction of the grid is one of the major difficulties in the application of CFD to the analysis of flow about actual aircraft configurations. Due to geometric complexity, the grid has to be constructed in simple subregions and then all of these subgrids have to be pieced together to form a complete grid for the entire flow field. The entire grid, which is called a composite grid because it is formed from many parts, may have common regions. In either case, the computation of the flow field, using any numerical algorithm, will require the transfer of information between individual subgrids. The transfer of information is more difficult with overlapping grids. Algorithms have been developed and tested for automating the transfer of information between two overlapping grids.

Mastin, Charles Wayne↗

NASA NTRS1991

Unsteady-flow-field predictions for oscillating cascades

The unsteady flow field around an oscillating cascade of flat plates with zero stagger was studied by using a time marching Euler code. This case had an exact solution based on linear theory and served as a model problem for studying pressure wave propagation in the numerical solution. The importance of using proper unsteady boundary conditions, grid resolution, and time step size was shown for a moderate reduced frequency. Results show that an approximate nonreflecting boundary condition based on linear theory does a good job of minimizing reflections from the inflow and outflow boundaries and allows the placement of the boundaries to be closer to the airfoils than when reflective boundaries are used. Stretching the boundary to dampen the unsteady waves is another way to minimize reflections. Grid clustering near the plates captures the unsteady flow field better than when uniform grids are used as long as the 'Courant Friedrichs Levy' (CFL) number is less than 1 for a sufficient portion of the grid. Finally, a solution based on an optimization of grid, CFL number, and boundary conditions shows good agreement with linear theory.

Huff, Dennis L.↗

NASA NTRS1995

Rapid Numerical Simulation of Viscous Axisymmetric Flow Fields

A two-dimensional Navier-Stokes code has been developed for rapid numerical simulation of axisymmetric flow fields, including flow fields with an azimuthal velocity component. The azimuthal-invariant Navier-Stokes equations in a cylindrical coordinate system are mapped to a general body-fitted coordinate system, with the streamwise viscous terms then neglected by applying the thin-layer approximation. Turbulence effects are modeled using an algebraic model, typically the Baldwin-Lomax turbulence model, although a modified Cebeci-Smith model can also be used. The equations are discretized using central finite differences and solved using a multistage Runge-Kutta algorithm with a spatially varying time step and implicit residual smoothing. Results are presented for calculations of supersonic flow over a waisted body-of-revolution, transonic flow through a normal shock wave in a straight circular duct of constant cross sectional area, swirling supersonic (inviscid) flow through a strong shock in a straight radial duct, and swirling subsonic flow in an annular-to-circular diffuser duct. Comparisons between computed and experimental results are in fair to good agreement, demonstrating that the viscous code can be a useful tool for practical engineering design and analysis work.

Tweedt, Daniel L.↗

NASA NTRS1972

Reentry heating and flow fields for Space Shuttle Orbiter at high angle of attack.

Rarefied flow fields and heating rates are calculated by a Monte Carlo direct simulation technique for several shuttle orbiter configurations at angles of attack between 40 and 60 deg. Continuum inviscid flow fields are determined by 2-D unsteady and 3-D steady finite-difference/artificial viscosity techniques used in combination with a 2-D shock layer analysis method. Continuum viscous flow fields and heating rates are computed by a boundary-layer integral matrix technique and an aerodynamic heating method.

Rochelle, W. C.↗

NASA NTRS1983

The disturbance flow field produced by an evolving vortex

The flow field of a vortex in a viscous shear flow is found by constructing a uniformly valid asymptotic expansion consisting of an inner solution field represented, to lowest order, by a two dimensional, nonliner, inviscid Stuart vortex and an outer solution field represented, to lowest order, by either a two dimensional parallel or self similar viscous flow. The technique involves scaling both the transverse and streamwise coordinates in the vicinity of the vortex as well as allowing for a slow variation of the outer viscous flow. Criteria are established for both the size of the vortical structure and proximity to the boundary surfaces. The composite solution is a consistent mathematical picture of the flow field at a fixed streamwise location as the vortical structure evolves past this point. Such a formulation is also useful in the specification of boundary or initial conditions in numerical fluid dynamic calculations, where an inconsistent setting of these conditions leads to spurious results for rather long computation times.

Gatski, T. B.↗

NASA NTRS1993

An experimental study of the flow field surrounding a subsonic jet in a cross flow

An experimental investigation of the flow interaction of a 5.08 cm (2.00 in.) diameter round subsonic jet exhausting perpendicularly to a flat plate in a subsonic cross flow was conducted in the NASA Ames 7x1O ft. Wind Tunnel Number One. Flat plate surface pressures were measured at 400 locations in a 30.48 cm (12.0 in.) concentric circular array surrounding the jet exit. Results from these measurements are provided in tabular and graphical form for jet-to-crossflow velocity ratios ranging from 4 to 12, and for jet exit Mach numbers ranging from 0.50 to 0.93. Laser doppler velocimeter (LDV) three component velocity measurements were made in selected regions in the developed jet plume and near the flat plate surface, at a jet Mach number of 0.50 and jet-to-crossflow velocity ratios of 6 and 8. The results of both pressure and LDV measurements are compared with the results of previous experiments. In addition, pictures of the jet plume shape at jet velocity ratios ranging from 4 to 12 were obtained using schleiren photography. The LDV measurements are consistent with previous work, but more extensive measurements will be necessary to provide a detailed picture of the flow field. The surface pressure results compare closely with previous work and provide a useful characterization of jet induced surface pressures. The results demonstrate the primary influence of jet velocity ratio and the secondary influence of jet Mach number in determining such surface pressures.

Dennis, Robert Foster↗

NASA NTRS1984

Numerical simulation of the viscous flow fields over three-dimensional complicated geometries

A 'thin-layer' Navier-Stokes code capable of predicting steady state viscous flows is applied to complicated three-dimensional flow fields. The code is written in a generalized coordinate system, and a recently developed grid generation procedure is used for the flow-field discretization. Application is made to the vortical flow over a delta wing at high angle of attack, and the computed results are compared with experimental results. The results indicate that the present method can capture the physical phenomenon well. It is observed that a leading-edge separation vortex is formed over the wing, as is a secondary separation vortex near the leading edge. The flow field behind the trailing edge is also well described. Application is also made to the transonic flow over the Shuttle configuration. The result appears to be reasonable even though no experimental data are available for comparison. These results indicate that the present approach is capable of computing complicated three-dimensional flow fields.

Fujii, K.↗

NASA NTRS1981

Numerical study of a scramjet engine flow field

A computer program has been developed to analyze the turbulent reacting flow field in a two-dimensional scramjet engine configuration. The program numerically solves the full two-dimensional Navier-Stokes and species equations in the engine inlet and combustor, allowing consideration of flow separation and possible inlet-combustor interactions. The current work represents an intermediate step towards development of a three-dimensional program to analyze actual scramjet engine flow fields. Results from the current program are presented that predict the flow field for two inlet-combustor configurations, and comparisons of the program with experiment are given to allow assessment of the modeling that is employed.

Drummond, J. P.↗