SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Guidelines and constraints procedures for LAGEOS assembly, operation, and design performance are given. Special attention was given to thermal, optical, and dynamic analysis and testing. The operation procedures illustrate the interrelation and sequence of tasks in a flow diagram. The diagram also includes quality assurance functions for verification of operation tasks.
A thermochemical water splitting process, the Ispra Mark-10 chemical reaction cycle, was chosen for examining the possibility of using water to produce hydrogen on a large scale for fuel and major industrial chemical uses. The assumed energy source for the process is an HTGR (helium cooled). A process flow diagram, a material balance, and an energy balance were developed for the thermochemical reaction cycle. Principal reactions which constitute the cycle are included.
The Shuttle Electric Power System Analysis SEPS computer program which performs detailed load analysis including predicting energy demands and consumables requirements of the shuttle electric power system along with parameteric and special case studies on the shuttle electric power system is described. The functional flow diagram of the SEPS program is presented along with data base requirements and formats, procedure and activity definitions, and mission timeline input formats. Distribution circuit input and fixed data requirements are included. Run procedures and deck setups are described.
The APAS program a multistation structural synthesis procedure developed to evaluate material, geometry, and configuration with various design criteria usually considered for the primary structure of transport aircraft is described and evaluated. Recommendations to improve accuracy and extend the capabilities of the APAS program are given. Flow diagrams are included.
Electric power plant costs and efficiencies are presented for three basic open-cycle MHD systems: (1) direct coal fired system, (2) a system with a separately fired air heater, and (3) a system burning low-Btu gas from an integrated gasifier. Power plant designs were developed corresponding to the basic cases with variation of major parameters for which major system components were sized and costed. Flow diagrams describing each design are presented. A discussion of the limitations of each design is made within the framework of the assumptions made.
The process of geometric parameter estimation to accuracies of one centimeter, i.e., multilateration, is defined and applications are listed. A brief functional explanation of the theory is presented. Next, various multilateration systems are described in order of increasing system complexity. Expected systems accuracy is discussed from a general point of view and a summary of the errors is listed. An outline of the design of a software processing system for multilateration, called MICRODOT, is presented next. The links of this software, which can be used for multilateration data simulations or operational data reduction, are examined on an individual basis. Functional flow diagrams are presented to aid in understanding the software capability. MICRODOT capability is described with respect to vehicle configurations, interstation coordinate reduction, geophysical parameter estimation, and orbit determination. Numerical results obtained from MICRODOT via data simulations are displayed both for hypothetical and real world vehicle/station configurations such as used in the GEOS-3 Project. These simulations show the inherent power of the multilateration procedure.
Detailed requirements for the mission planning processor are documented. The mission planning processor is a user oriented tool for consumables management and is part of the total consumables subsystem management concept. A quasi top-down approach was applied to the design of the mission planning processor. Interface requirements, input/output, and data base concepts were considered before computational processing. Existing analytical models were investigated for applicability before new models were developed. The mission planning processor was designed for an interactive system using demand terminals for input/outputdisplay and interfacing with an updateable mission data bank. The control and support routines provide the user interface, peripheral data handling, program control, and support functions required by the mission planning processor for execution on an interactive system. A description, interface requirements, definition of internal variables, listing of input data, processing flow diagram, and listing of output data are presented for each routine.
The processing of time in the Orbiter System Services software and the associated facilities provided to the user community are described. The descriptions are directed toward showing the functional intent of the design rather than the actual implementation. Simplified flow diagrams are included. Based upon detailed analysis of a preliminary review copy of the Approach and Landing Test (ALT) System Software Detailed Design Specification and the Program Listings for Version 17 Prime, the processing of time has the potential for error free operations. The processing of time is not expected to change between ALT and the Operational Flight Test (OFT) other than differences in value of some constants for control and limit checking. Due to the dynamic nature of onboard time processing and its criticality to the successful operation of the orbiter, it is recommended that a comprehensive list of external variables, their locations, initial values, and a 'where used' listing be produced, as a by-product of the link edit process, for all non-HAL coding. In addition, a careful review of the verification test procedures for the System Services time-related software is recommended.
Assumptions made and techniques used in modeling the power network to the 480 volt level are discussed. Basic computational techniques used in the short circuit program are described along with a flow diagram of the program and operational procedures. Procedures for incorporating network changes are included in this user's manual.
The details of the Remote Manipulator System kinematic model implemented into the Space Vehicle Dynamics Simulation are given. Detailed engineering flow diagrams and definitions of terms are included.
The microwave scanning beam landing system (MSBLS) is the primary position sensor of the Orbiter's navigation subsystem during the autoland phase of the flight. Portions of the system are discussed with special emphasis placed on potential problem areas as referenced to the Orbiter's mission. Topics discussed include system compatability, system accuracy, and expected RF signal levels. A block and flow diagram of MSBLS system operation is included with a list of special tests required to determine system performance.
All microprocessor units have a similar architecture from which a basic test philosophy can be adopted and used to develop an approach to test each module separately in order to verify the functionality of each module within the device using the input/output pins of the device and its instruction set; test for destructive interaction between functional modules; and verify all timing, status information, and interrupt operations of the device. Block and test flow diagrams are given for the 8080, 8008, 2901, 6800, and 1802 microprocessors. Manufacturers are listed and problems encountered in testing the modules are discussed. Test equipment and methods are described.
The purpose of the Shuttle microwave system experiment (SIMS) is to utilize the capabilities of the Space Shuttle to perform passive microwave measurements of thermal emission from the earth's atmosphere and surface, which can be interpreted in terms of meaningful atmospheric and geophysical parameters. The paper is a status report of an ongoing definition phase study of SIMS. The wavelengths and observable parameters for the SIMS channels are identified. The SIMS instrument is discussed with particular reference to the antenna system. A system consisting of a parabolic torus reflector offset fed by a number of feeds and radiometers on a rotating wheel is determined to be the best antenna configuration for SIMS. A tentative data flow diagram for SIMS is also provided.
A digital processing and analysis scheme for use with digitized synthetic aperture radar data was developed. Using data from a four channel system, the imagery is preprocessed using specially designed software and then analyzed using preexisting facilities originally intended for use with MSS type data. Geometric and radiometric correction may be performed if desired, as well as classification analysis, Fast Fourier transform, filtering and level slice and display functions. The system provides low cost output in real time, permitting interactive imagery analysis. System information flow diagrams as well as sample output products are shown.
For 36 hours during April 1975, an atmospheric variability experiment was conducted. This research effort supported an observational program in which rawinsonde data, radar data, and satellite data were collected from a network of 42 stations east of the Rocky Mountains at intervals of 3 hours. This program presents data with a high degree of time resolution over a spatially and temporally extensive network. Reduction of the experiment data is intended primarily as a documentation of the checking and processing of the data and should be useful to prospective users. Various flow diagrams of the data processing procedures are described, and a complete summary of the formulas used in the data processing is provided. A wind computation scheme designed to extract as much detailed wind information as possible from the unique experiment data set is discussed. The accuracy of the thermodynamic and wind data were estimated. Errors in the thermodynamic and wind data are given.
The study objectives of the Spacelab level 4 analysis were defined, along with the most significant results. The approach used in the synthesis and selection of alternate level 4 integration is described; the options included distributed site, lead center, and launch site. Principal characteristics, as well as the functional flow diagrams for each option, are presented and explained.
The ROBOT display and control program (ROBDAC) to be written for the Adage 340 computer is designed to communicate with the Univac 1110 computer with the aid of the graphic support communications programs. ROBDAC and the Adage computer act as an input/output device for the program ROBOT, which is run on the Univac 1110. ROBDAC controls the input to ROBOT by displaying images of the inputs, providing an editing technique for these inputs, shipping the input data to the Univac, and then commanding ROBOT to start execution. The output is done in a similar manner after receiving the output data from the Univac. This data will be displayed numerically as well as by plotted graphs. All of the input/output will be done interactively with practically 'finger tip' control. A general program flow diagram of ROBDAC is included.
Work was done to verify the technological readiness of a select process sequence with respect to satisfying the Low Cost Solar Array Project objectives of meeting the designated goals of $.50 per peak watt in 1986 (1975 dollars). The sequence examined consisted of: (1) 3 inches diameter as-sawn Czochralski grown 1:0:0 silicon, (2) texture etching, (3) ion implanting, (4) laser annealing, (5) screen printing of ohmic contacts and (6) sprayed anti-reflective coatings. High volume production projections were made on the selected process sequence. Automated processing and movement of hardware at high rates were conceptualized to satisfy the PROJECT's 500 MW/yr capability. A production plan was formulated with flow diagrams integrating the various processes in the cell fabrication sequence.