Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fasteners”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Stress corrosion susceptibility of stress-coined fastener holes in aircraft structures

The cold working process of stress coining is used to provide fatigue improvement of fastener holes in aircraft structures. The cold working produces a radial flow of the metal. The residual stresses resulting from stress coining provide protection against fatigue damage by opposing the applied tensile stresses in service at the edge of the fastener hole. However, it is shown in this paper that in addition to the compressive stresses surrounding the stress coined hole, there are tensile stresses that result from the coining operation and that these residual tensile stresses can have a deleterious effect on the stress corrosion susceptibility of the postcoined structure.

Carter, A. E.↗
NASA NTRS1977

Allowable bending loads for mechanical fasteners

Modified shear-loading setup is used to determine allowable shear bending loads on mechanical fasteners. System reduces number of tests required for direct analysis of fasteners to two.

Ferdie, R. D.↗
NASA NTRS1982

Blind Fastener Is Easy To Install

Panels, sheets, doors and other structures could be easily attached to and removed from mating part by proposed new fastener. Fastener is permanently anchored in removable part only. Its protruding end is inserted into a hole in mating part. When wedge pin is screwed tightly closed, segmented collar contracts or expands to release parts or to grip them. Installation has no loose parts, and no rear nut is needed.

Peterson, S. A.↗
NASA NTRS1983

Quick-Disconnect Fastener

Proposed quick-disconnect fastener for two or more parts resists shear loads and torque. Device centers parts to be joined, clamps and tightens them into single unit. Potential applications for removable fastener include holding parts for welding, brazing, soldering, riveting, and gluing. Other possible uses are for attaching removable panels and panels with poor access on one side and plugging leaks in pressure vessels.

Palmer, L. W.↗
NASA NTRS1986

More Secure Fastening for Tracked-Vehicle Pads

Method of fastening road pads on tracked vehicles ensures retaining tabs properly installed and less likely to fail from shock or pad squirming when tracked vehicle turns. No risk squirming of pad might overcome retaining force of rubber encapsulation or teeth of split-collet fastener shred soft-iron projections on pad shell, causing inadvertent release of pad. Rod extending through track shells and tabs on pad shells includes grooved cams to secure pads.

Collins, Earl R., Jr.↗
NASA NTRS1986

Thermal-Stress-Free Fasteners for Orthotropic Materials

Theoretical basis for design of thermal-stress-free fasteners developed. Two-dimensional analysis defines shapes of interfaces between materials. Design technique determines fastener shapes that maintain tight thermal-stress-free joint while joint undergoes uniform temperature change.

Blosser, M. L.↗
NASA NTRS1985

Automatic Fastening Large Structures: a New Approach

The external tank (ET) intertank structure for the space shuttle, a 27.5 ft diameter 22.5 ft long externally stiffened mechanically fastened skin-stringer-frame structure, was a labor intensitive manual structure built on a modified Saturn tooling position. A new approach was developed based on half-section subassemblies. The heart of this manufacturing approach will be 33 ft high vertical automatic riveting system with a 28 ft rotary positioner coming on-line in mid 1985. The Automatic Riveting System incorporates many of the latest automatic riveting technologies. Key features include: vertical columns with two sets of independently operating CNC drill-riveting heads; capability of drill, insert and upset any one piece fastener up to 3/8 inch diameter including slugs without displacing the workpiece offset bucking ram with programmable rotation and deep retraction; vision system for automatic parts program re-synchronization and part edge margin control; and an automatic rivet selection/handling system.

Lumley, D. F.↗
NASA NTRS1991

Quick-Connect Truss Fastener

Quick-connect fastener actuated by simple motion of hexagonal wrench. Enables assembly of truss by heavily gloved technician or by robot. Originally designed for use by Astronaut or robot assembling a truss in outer space, fastener also adapts to various connection applications requiring quick assembly or disassembly.

Sheridan, Philip L.↗
NASA NTRS1992

Fastener For Hot, Oxidizing Environments

Threaded halves of metallic collar fit around tapered shank of body of fastener. Retaining ring holds collar on body. Ceramic coat gives fastener its resistance to oxidation. Assembled and disassembled quickly from outside.

Dunn, Thomas J.↗
NASA NTRS1992

"Easy-on, Easy-off" Blanket Fastener

Fasteners hold flexible blanket on set of posts on supporting structure. Disk of silicone rubber cast on disk of Mylar, fastened to blanket and press-fit over post to nest securely in groove. No tools needed for installation or removal.

Kolecki, Ronald E.↗
NASA NTRS1992

Hidden Fastening-And-Unfastening Mechanism

Proposed mechanism placed behind panel fastens panel to, or unfastens it from, underlying structure. Electric motor and gearbox drives bolt to engage or disengage captive floating nut. Used where head at outer end of bolt or other fastener covered with protective outer layer on panel and inner end of bolt inaccessible.

Macconochie, Ian O.↗
NASA NTRS1992

Carbon/Carbon Fasteners For Use At High Temperatures

Fasteners made of advanced carbon/carbon material perform well at ambient and high temperatures. Exhibit shear strengths of more than 10 kpsi at room temperature and 13 kpsi at temperature of 2,700 degrees F. However, fasteners exhibited poor tensile strength at room temperature. Best suited to applications in which exposed to shear loads with minimal tension loads. Parts reused after thermal cycling.

Bohlmann, Frank J.↗
NASA NTRS1992

Effects of long-term exposure on LDEF fastener assemblies

This presentation summarizes the Systems Special Investigations Group (SIG) findings from testing and analysis of fastener assemblies used on the Long Duration Exposure Facility (LDEF) structure, the tray mounting clamps, and by the various experimenters. The LDEF deintegration team and several experimenters noted severe fastener damage and hardware removal difficulties during post-flight activities. The System SIG has investigated all reported instances, and in all cases examined to date, the difficulties were attributed to galling during installation or post-flight removal. To date, no evidence of coldwelding was found. Correct selection of materials and lubricants as well as proper mechanical procedures is essential to ensure successful on-orbit or post-flight installation and removal of hardware.

Spear, Steve↗
NASA NTRS1997

Fastener Design Course

Richard T. Barrett, Senior Aerospace Engineer of NASA Lewis Research Center presents a comprehensive course on fastener design. A recognized expert in the field of fastener technology Mr. Barrett combines lecture, charts, illustrations with real-world experiences. Topics covered include: materials, plantings and coatings, locking methods threads, joint stiffness, rivets, inserts, nut plates, thread lubricants, design criteria, etc. A workbook accompanies the DVD.

Barrett, Richard T.↗
NASA NTRS2006

Experimental Observations for Determining the Maximum Torque Values to Apply to Composite Components Mechanically Joined With Fasteners (MSFC Center Director's Discretionary Fund Final Report, Proj. 03-13}

Aerospace structures utilize innovative, lightweight composite materials for exploration activities. These structural components, due to various reasons including size limitations, manufacturing facilities, contractual obligations, or particular design requirements, will have to be joined. The common methodologies for joining composite components are the adhesively bonded and mechanically fastened joints and, in certain instances, both methods are simultaneously incorporated into the design. Guidelines and recommendations exist for engineers to develop design criteria and analyze and test composites. However, there are no guidelines or recommendations based on analysis or test data to specify a torque or torque range to apply to metallic mechanical fasteners used to join composite components. Utilizing the torque tension machine at NASA s Marshall Space Flight Center, an initial series of tests were conducted to determine the maximum torque that could be applied to a composite specimen. Acoustic emissions were used to nondestructively assess the specimens during the tests and thermographic imaging after the tests.

Thomas, F. P.↗
NASA NTRS2000

Fastener

A fastener body comprises a head and a shank fabricated from a composite material. The head has at least one side which extends beyond the side of the shank and has two other sides coplanar with the shank. A fastener for engaging a liner has perpendicular lengthwise and widthwise reference axes and a head and a shank, with the shank extending in a first lengthwise direction away from the head, the head further having at least one extension that extends in the widthwise direction beyond the shank for engaging the liner, wherein substantially all lengthwise directed load components transmitted from the liner to the head are transmitted through the extension.

Miller, Robert J.↗
NASA NTRS2011

Performance Characterization of Loctite (Registered Trademark) 242 and 271 Liquid Locking Compounds (LLCs) as a Secondary Locking Feature for International Space Station (ISS) Fasteners

Several International Space Station (ISS) hardware components use Loctite (and other polymer based liquid locking compounds (LLCs)) as a means of meeting the secondary (redundant) locking feature requirement for fasteners. The primary locking method is the fastener preload, with the application of the Loctite compound which when cured is intended to resist preload reduction. The reliability of these compounds has been questioned due to a number of failures during ground testing. The ISS Program Manager requested the NASA Engineering and Safety Center (NESC) to characterize and quantify sensitivities of Loctite being used as a secondary locking feature. The findings and recommendations provided in this investigation apply to the anaerobic LLCs Loctite 242 and 271. No other anaerobic LLCs were evaluated for this investigation. This document contains the findings and recommendations of the NESC investigation

Dube, Michael J.↗
NASA NTRS1997

Fastener Design Course [Workbook]

Richard T. Barrett, Senior Aerospace Engineer of NASA Lewis Research Center presents a comprehensive course on fastener design. A recognized expert in the field of fastener technology Mr. Barrett combines lecture, charts, illustrations with real-world experiences. Topics covered include: materials, plantings and coatings, locking methods threads, joint stiffness, rivets, inserts, nut plates, thread lubricants, design criteria, etc. These presentation slides accompany the DVD.

Barrett, Richart T.↗