Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electron tubes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Secondary-electron-emission properties of conducting surfaces with application to multistage depressed collectors for microwave amplifiers

To improve the efficiency of high power microwave tubes, low secondary electron yield electrode surface for use in depressed collectors are needed. The secondary emission characteristics of a number of materials were investigated. The materials studied were beryllium, carbon (soot and pyrolytic graphite), copper, titanium carbide, and tantalum. Both total secondary yield delta and relative reflected primary yield were measured. These measurements were made in conjunction with Auger spectroscopy so that the secondary emission characteristics could be determined as a function of surface contamination or purity. The results show that low atomic weight elements, such as beryllium and carbon, have the lowest reflected primary yield and that roughening the surface of an electrode can markedly decrease secondary yield both for delta and reflected primaries. All factors considered, a roughened pyrolytic graphite surface showed the greatest potential for use as an electrode surface in depressed collectors.

Forman, R.↗
NASA NTRS2018

Space Qualified 200-Watt Q-band Linearized Traveling-Wave Tube Amplifier

L3 Technologies Electron Devices Division, (L3 EDD) and L3 Technologies Narda Microwave West (L3 NMW), are completing space-flight qualification for a 200-watt Q-band linearized channelized traveling-wave tube amplifier (LCTWTA) capable of over 5 GHz instantaneous bandwidth in a conduction-cooled package. This paper will discuss the LCTWTA performance, manufacturing and flight qualification test results.

Traveling-Wave Tube Amplifier↗
NASA NTRS2018

Space Qualified 200-Watt Q-Band Linearized Traveling-Wave Tube Amplifier

L3 Technologies Electron Devices Division, (L3 EDD) and L3 Technologies Narda Microwave West (L3 NMW), are completing space-flight qualification for a 200-watt Q-band linearized channelized traveling-wave tube amplifier (LCTWTA) capable of over 5 GHz instantaneous bandwidth in a conduction-cooled package. This paper will discuss the LCTWTA performance, manufacturing and flight qualification test results.

Q-band↗
NASA NTRS1986

Secondary-electron-emission losses in multistage depressed collectors and traveling-wave-tube efficiency improvements with carbon collector electrode surfaces

Secondary-electron-emission losses in multistage depressed collectors (MDC's) and their effects on overall traveling-wave-tube (TWT) efficiency were investigated. Two representative TWT's and several computer-modeled MDC's were used. The experimental techniques provide the measurement of both the TWT overall and the collector efficiencies. The TWT-MDC performance was optimized and measured over a wide range of operating conditions, with geometrically identical collectors, which utilized different electrode surface materials. Comparisons of the performance of copper electrodes to that of various forms of carbon, including pyrolytic and iisotropic graphites, were stressed. The results indicate that: (1) a significant improvement in the TWT overall efficiency was obtained in all cases by the use of carbon, rather than copper electrodes, and (2) that the extent of this efficiency enhancement depended on the characteristics of the TWT, the TWT operating point, the MDC design, and collector voltages. Ion textured graphite was found to be particularly effective in minimizing the secondary-electron-emission losses. Experimental and analytical results, however, indicate that it is at least as important to provide a maximum amount of electrostatic suppression of secondary electrons by proper MDC design. Such suppression, which is obtained by ensuring that a substantial suppressing electric field exists over the regions of the electrodes where most of the current is incident, was found to be very effective. Experimental results indicate that, with proper MDC design and the use of electrode surfaces with low secondary-electron yield, degradation of the collector efficiency can be limited to a few percent.

Ramins, P.↗
NASA NTRS2004

COTS MEMS Flow-Measurement Probes

As an alternative to conventional tubing instrumentation for measuring airflow, designers and technicians at Glenn Research Center have been fabricating packaging components and assembling a set of unique probes that contain commercial off-the-shelf (COTS) microelectromechanical systems (MEMS) sensor chips. MEMS sensor chips offer some compelling advantages over standard macroscopic measurement devices. MEMS sensor technology has matured through mass production and use in the automotive and aircraft industries. At present, MEMS are the devices of choice for sensors in such applications as tire-pressure monitors, altimeters, pneumatic controls, cable leak detectors, and consumer appliances. Compactness, minimality of power demand, rugged construction, and moderate cost all contribute to making MEMS sensors attractive for instrumentation for future research. Conventional macroscopic flow-measurement instrumentation includes tubes buried beneath the aerodynamic surfaces of wind-tunnel models or in wind-tunnel walls. Pressure is introduced at the opening of each such tube. The pressure must then travel along the tube before reaching a transducer that generates an electronic signal. The lengths of such tubes typically range from 20 ft (approx.= 6 m) to hundreds of feet (of the order of 100 m). The propagation of pressure signals in the tubes damps the signals considerably and makes it necessary to delay measurements until after test rigs have reached steady-state operation. In contrast, a MEMS pressure sensor that generates electronic output can take readings continuously under dynamic conditions in nearly real time. In order to use stainless-steel tubing for pressure measurements, it is necessary to clean many tubes, cut them to length, carefully install them, delicately deburr them, and splice them. A cluster of a few hundred 1/16-in.- (approx.=1.6-mm-) diameter tubes (such clusters are common in research testing facilities) can be several inches (of the order of 10 cm) in diameter and could weigh enough that two technicians are needed to handle it. Replacing hard tubing with electronic chips can eliminate much of the bulk. Each sensor would fit on the tip of a 1/16-in. tube with room to spare. The Lucas NovaSensor P592 piezoresistive silicon pressure sensor was chosen for this project because of its cost, availability, and tolerance to extreme ambient conditions. The sensor chip is 1 mm square by 0.6 mm thick (about 0.039 by 0.039 by 0.024 in.) and includes 0.12-mm (approx.=0.005-in.) wire connection tabs. The figure shows a flow-angularity probe that was built by use of three such MEMS chips. It is planned to demonstrate this MEMS probe as an alternative to a standard tube-type "Cobra" probe now used routinely in wind tunnels and aeronautical hardware. This MEMS probe could be translated across a flow field by use of a suitable actuator, so that its accuracy and the shortness of its response time could be exploited to obtain precise dynamic measurements of a sort that cannot be made by use of conventional tubing-based instrumentation.

Redding, Chip↗
NASA NTRS1998

EMI Performance of the AIRS Cooler and Electronics

The TRW pulse tube cryocooler for JPL's Atmospheric Infrared Sounder (AIRS) instrument is required to meet stringent requirements for radiated electric and magnetic fields, conducted emissions on the input power bus, and electromagnetic susceptivility.

EMI AIRS Cooler Electronics Cryocooler↗
NASA NTRS1968

Technique increases storage capacity in camera tube target

Technique increases the signal current, where direct beam readout is used, in Secondary Electron Conduction /SEC/ camera tubes. Increasing the storage capacity and therefore the dynamic range of the SEC target permits satisfactory operation at reduced frame rates.

Boll, K. F.↗
NASA NTRS1988

Energy transport by energetic electrons released during solar flares. II - Current filamentation and plasma heating

Two-dimensional electrostatic particle simulations are performed in order to investigate energy transport associated with the propagation of energetic electrons through a flaring flux tube. Results indicate that as the energetic electrons flow outward, a return current of ambient plasma electrons is drawn inward (to maintain quasi-neutrality) which can be spatially separate from the primary current carried by the energetic electrons. Return current electrons are shown to accumulate on either side of the acceleration region of the energetic electrons, and depletions of ambient plasma electrons develop in the return current regions. Plasma ions accelerate across the field lines to produce current closure or charge neutralization, achieving energies comparable to those of the energetic electrons.

Winglee, R. M.↗
NASA NTRS1977

Small-size 81- to 83.5-percent efficient 2- and 4-stage depressed collectors for octave-bandwidth high-performance TWT's

In a joint USAF-NASA Program, Lewis Research Center is carrying out an efficiency improvement program on traveling wave tubes for use in electronic counter measures by applying multistage depressed collector (MDC) and spent beam refocusing techniques. In the analytic part of the effort, three-dimensional electron trajectories are computed throughout the TWT. On the experimental side, tube performance is evaluated first without the MDC; then, the spent beam is analyzed for symmetry, circularity, and velocity spread. The three-dimensional theory predicts a MDC-efficiency, at mid-band, of 81 per cent for a 2-stage MDC with symmetric, circular, and optimally refocused beams and 85.5 per cent for a 4-stage MDC. Experimental results to date have yielded MDC efficiencies of a minimum of 81 and 83 per cent for a 2- and 4-stage MDC, respectively, across a one-octave bandwidth of a 4.8 to 9.6 GHz 330-to-550-W TWT.

Kosmahl, H. G.↗
NASA NTRS1988

Energy transport by energetic electrons released during solar flares. I - Thermal versus nonthermal processes

The propagation of energetic electrons through a flaring flux tube is studied in an attempt to determine how the energy of the electrons is deposited in the flux tube. One-dimensional electrostatic particle simulations are used in the present investigation. As the energetic electrons propagate into the system, a return current of ambient plasma electrons and some of the energetic electrons is drawn into the energetic electron source. It is found that, as the ambient temperature relative to the ion temperature increases above about 3, the heated return-current electrons can excite ion-sound waves.

Winglee, R. M.↗
NASA NTRS1973

A laboratory simulation of a single-axis dual-level precision pointing system

The laboratory simulation of a scaled single-axis dual-level control system for a large space telescope is demonstrated. The dual-level control system consists of a coarse-body-pointing system and a fine-pointing system, which uses an image motion compensator, an image dissector tube, and digital electronics. The results of the simulation indicate that the dual-level system can be used to provide tracking capability within one-tenth of a diffraction-limited image diameter of a 3-meter f/100 telescope for stars up to a +12.3 visual magnitude.

Bullock, G. F.↗
NASA NTRS1973

Skylab experiments. Volume 1: Physical science, solar astronomy

The basic subject of this volume is the solar astronomy program conducted on Skylab. In addition to descriptions of the individual experiments and the principles involved in their performance, a brief description is included of the sun and the energy characteristics associated with each zone. Wherever possible, related classroom activities have been identified and discussed in some detail. It will be apparent that the relationships rest not only in the field of solar astronomy, but also in the following subjects: (1) physics - optics, electromagnetic spectrum, atomic structure, etc.; (2) chemistry - emission spectra, kinetic theory, X-ray absorption, etc.; (3) biology - radiation and dependence on the sun; (4) electronics - cathode ray tubes, detectors, photomultipliers, etc.; (5) photography; (6) astronomy; and (7) industrial arts.

Source record↗
NASA NTRS1978

The Tordo 1 polar cusp barium plasma injection experiment

In January 1975, two barium plasma injection experiments were carried out with rockets launched into the upper atmosphere where field lines from the dayside cusp region intersect the ionosphere. The Tordo 1 experiment took place near the beginning of a worldwide magnetic storm. It became a polar cap experiment almost immediately as convection perpendicular to the magnetic field moved the fluorescent plasma jet away from the cusp across the polar cap in an antisunward direction. Convection across the polar cap with an average velocity of more than 1 km/s was observed for nearly 40 min until the barium flux tubes encountered large electron fields associated with a poleward bulge of the auroral oval near Greenland. Prior to the encounter with the aurora near Greenland there is evidence of upward acceleration of the barium ions while they were in the polar cap. The three-dimensional observations of the plasma orientation and motion give an insight into convection from the cusp region across the polar cap, the orientation of the polar cap magnetic field lines out to several earth radii, the causes of polar cap magnetic perturbations, and parallel acceleration processes.

Wescott, E. M.↗