Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electrolyte additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Macroscale and Nanoscale Photoelectrochemical Behavior of p-Type Si(111) Covered by a Single Layer of Graphene or Hexagonal Boron Nitride

Two-dimensional (2D) materials may enable a general approach to the introduction of a dipole at a semiconductor surface as well as control over other properties of the double layer at a semiconductor/liquid interface. Vastly different properties can be found in the 2D materials currently studied due in part to the range of the distribution of density-of-states. In this work, the open-circuit voltage (V oc ) of p-Si–H, p-Si/Gr (graphene), and p-Si/h-BN (hexagonal boron nitride) in contact with a series of one-electron outer-sphere redox couples was investigated by macroscale measurements as well as by scanning electrochemical cell microscopy (SECCM). The band gaps of Gr and h-BN (0–5.97 eV) encompass the wide range of band gaps for 2D materials, so these interfaces (p-Si/Gr and p-Si/h-BN) serve as useful references to understand the behavior of 2D materials more generally. The value of Voc shifted with respect to the effective potential of the contacting solution, with slopes (ΔV oc /ΔE Eff ) of -0.27 and -0.38 for p-Si/Gr and p-Si/h-BN, respectively, indicating that band bending at the p-Si/h-BN and p-Si/Gr interfaces responds at least partially to changes in the electrochemical potential of the contacting liquid electrolyte. Additionally, SECCM is shown to be an effective method to interrogate the nanoscale photoelectrochemical behavior of an interface, showing little spatial variance over scales exceeding the grain size of the CVD-grown 2D materials in this work. The measurements demonstrated that the polycrystalline nature of the 2D materials had little effect on the results and confirmed that the macroscale measurements reflected the junction behavior at the nanoscale.

2D material↗
DOE OSTI2022

Tracking the Oxidation of Silicon Anodes Using Cryo-EELS upon Battery Cycling

Silicon is a high-capacity material for the anode of a rechargeable lithium-ion battery. One of the fundamental challenges for using Si in anodes is capacity fading, which has been revealed to be partially associated with the interfacial instability between the Si and liquid electrolyte due to the large volume swing of Si upon charging and discharging. Smart nanoscale design concepts, either pre-synthesized or formed in-situ, have led to the mitigation of the detrimental factors associated with the volume swing of Si. However, it has never been clear as how the chemical state of Si evolves and contributes to the capacity fading upon battery cycling. Here, we use cryo-electron energy loss spectroscopy (EELS) to directly monitor, at sub-nanometer scale, the chemical evolution of Si upon battery cycling. We discover that during the cycling process, Si particles are progressively oxidized to form SiO 2 , which is initiated from the particle surface and gradually penetrates toward the interior of the particle, directly contributing to the capacity fading. Possible mechanisms of Si oxidation are postulated. We further show how the cycling stability can be improved by an electrolyte additive to form an effective passivation layer, representatively, even a small concentration of fluoroethylene carbonate (FEC) causes the formation of an LiF layer on the Si nanoparticle surface that prevents Si oxidation and improves cycling stability. Furthermore, the present work unveils Si oxidation as a previously unrecognized factor that contributes to capacity fading, therefore providing insight into the design of anodes with Si based materials.

25 ENERGY STORAGE↗
DOE OSTI2022

Hollow-core optical fibre sensors for operando Raman spectroscopy investigation of Li-ion battery liquid electrolytes

Improved analytical tools are urgently required to identify degradation and failure mechanisms in Li-ion batteries. However, understanding and ultimately avoiding these detrimental mechanisms requires continuous tracking of complex electrochemical processes in different battery components. Here, we report an operando spectroscopy method that enables monitoring the chemistry of a carbonate-based liquid electrolyte during electrochemical cycling in Li-ion batteries with a graphite anode and a LiNi 0.8 Mn 0.1 Co 0.1 O 2 cathode. By embedding a hollow-core optical fibre probe inside a lab-scale pouch cell, we demonstrate the effective evolution of the liquid electrolyte species by background-free Raman spectroscopy. The analysis of the spectroscopy measurements reveals changes in the ratio of carbonate solvents and electrolyte additives as a function of the cell voltage and show the potential to track the lithium-ion solvation dynamics. The proposed operando methodology contributes to understanding better the current Li-ion battery limitations and paves the way for studies of the degradation mechanisms in different electrochemical energy storage systems.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Unusual Li 2 O sublimation promotes single-crystal growth and sintering

Li 2 O is rarely used for cathode material synthesis due to its high melting point (1,438 °C). Here we discover that Li 2 O can sublimate at 800-1,000 °C under ambient pressure, opening new possibilities for cathode synthesis. We propose a mechanism that enables synthesis of single crystals-such as LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) or LiNi 0.9 Mn 0.05 Co 0.05 O 2 (NMC90)-without direct contact with Li 2 O salts. We show that Li 2 O vapour successfully converts spent polycrystalline NMC811 into segregated single crystals without milling or post-treatment. The Li 2 O vapour, derived from Li 2 O solids, diffuses rapidly and reacts with precursors, mimicking a molten-salt environment, which facilitates single-crystal growth. The chemical lithiation process continuously drives Li 2 O sublimation, sintering the crystals. Single crystals derived from Li 2 O and fresh precursors or spent polycrystals exhibit outstanding cycling after 1,000 cycles in full cells. The demonstrated Li 2 O sublimation and its universal role in promoting single-crystal growth provides an effective approach for single-crystal synthesis, scale-up and recycling.

25 ENERGY STORAGE↗
DOE OSTI2025

Investigating the effect of heterogeneities across the electrode|multiphase polymer electrolyte interfaces in high-potential lithium batteries

Polymer electrolytes hold great promise for safe and high-energy batteries comprising solid or semi-solid electrolytes. Multiphase polymer electrolytes, consisting of mobile and rigid phases, exhibit fast ion conduction and desired mechanical properties. However, fundamental challenges exist in understanding and regulating interactions at the electrode|electrolyte interface, especially when using high-potential layered oxide active materials at the positive electrode. Here we demonstrate that depletion of the mobile conductive phase at the interface contributes to battery performance degradation. Molecular ionic composite electrolytes, composed of a rigid-rod ionic polymer with nanometric mobile cations and anions, serve as a multiphase platform to investigate the evolution of ion conductive domains at the interface. Chemical and structural characterizations enable the visualization of concentration heterogeneity and spatially resolve the interfacial chemical states over a statistically significant field of view for buried interfaces. We report that concentration and chemical heterogeneities prevail at electrode|electrolyte interfaces, leading to phase separation in polymer electrolytes. In conclusion, understanding the hidden roles of interfacial chemomechanics in polymer electrolytes enables us to design an interphase tailoring strategy based on electrolyte additives to mitigate the interfacial heterogeneity and improve battery performance.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Self-replenishing Ni-rich stainless-steel electrode toward oxygen evolution reaction at ampere-level

In the past few decades, tremendous attention has been devoted to enhancing the activity of oxygen evolution reaction (OER) catalysts for hydrogen production, while the cost and long-term stability of catalysts, which can play an even more important role in industrialization, have been much less emphasized. Herein, we engineered an OER electrode from abundant stainless steel (SS) via facile approaches, and the obtained electrode consists of a Ni-rich oxide surface layer with a Fe-rich metal substrate. An outstanding activity was observed with an overpotential of 316 mV at 100 mA cm −2 in 1 M KOH electrolyte. Additionally, an electrode self-replenishing concept is proposed in which a Ni-rich catalyst layer can be regenerated from a metallic substrate due to the difference in diffusion and dissolution rates of metal oxides/hydroxides, and this regeneration is validated by various characterizations. A recorded degradation rate of 0.012 was observed at 1000 mA cm −2 for 1000 h. The facile engineering of OER electrodes from SS combined with the self-replenishing catalyst can potentially address the cost, activity, and long-term stability barriers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

A high-throughput experimentation platform for data-driven discovery in electrochemistry

Automating electrochemical analyses combined with artificial intelligence is poised to accelerate discoveries in renewable energy sciences and technologies. This study presents an automated high-throughput electrochemical characterization (AHTech) platform as a cost-effective and versatile tool for rapidly assessing liquid analytes. The Python-controlled platform combines a liquid handling robot, potentiostat, and customizable microelectrode bundles for diverse, reproducible electrochemical measurements in microtiter plates, minimizing chemical consumption and manual effort. To showcase the capability of AHTech, we screened a library of 180 small molecules as electrolyte additives for aqueous zinc metal batteries, generating data for training machine learning models to predict Coulombic efficiencies. Key molecular features governing additive performance were elucidated using Shapley Additive exPlanations and Spearman’s correlation, pinpointing high-performance candidates like cis-4-hydroxy-d-proline, which achieved an average Coulombic efficiency of 99.52% over 200 cycles. The workflow established herein is highly adaptable, offering a powerful framework for accelerating the exploration and optimization of extensive chemical spaces across diverse energy storage and conversion fields.

Lin, Dian-Zhao [Johns Hopkins University, Baltimor↗
DOE OSTI2021

Effect of Temperature and FEC on Silicon Anode Heat Generation Measured by Isothermal Microcalorimetry

Isothermal microcalorimetry (IMC) was used to better understand parasitic reactions and heat generation from Si electrodes in the first 10 cycles using Li/Si half cells. Heat generation from cell polarization (ohmic heat), entropy changes (reversible heat), and parasitic reactions (parasitic heat) are separated and quantified. The effect of temperature and fluoroethylene carbonate (FEC) as an electrolyte additive are also explored. Our results show that at the C/10 cycling rate used here, ohmic heat makes the largest contribution to overall heat generation while reversible heat is the smallest. Ohmic heat generation increases with cycle number due to increasing internal resistance, though the effect is smaller for cells with FEC. Interestingly, capacity-normalized parasitic heat generation is largely unaffected by changes in temperature despite differing reaction kinetics. We show that this is caused by a decrease in average parasitic reaction enthalpy as temperature is increased. Further, cells with FEC display higher average parasitic reaction enthalpy than cells without. The average parasitic reaction enthalpies for all the Si electrodes we tested were lower than previously reported values for graphite, indicating that the SEI formed on Si is less stable.

25 ENERGY STORAGE↗
DOE OSTI2022

Critical Evaluation of Potentiostatic Holds as Accelerated Predictors of Capacity Fade during Calendar Aging

Li-ion batteries will lose both capacity and power over time due to calendar aging caused by slow parasitic processes that consume Li + ions. Studying and mitigating these processes is traditionally an equally slow venture, which is especially taxing for the validation of new active materials and electrolyte additives. Here, we evaluate whether potentiostatic holds can be used to accelerate the diagnosis of Li + loss during calendar aging. The technique is based on the idea that, under the right conditions, the current measured as the cell voltage is held constant can be correlated with the instantaneous rate of side reactions. Thus, in principle, these measurements could capture the rate of capacity fade in real time . In practice, we show that this method is incapable of quantitatively forecasting calendar aging trends. Instead, our study demonstrates that potentiostatic holds can be applied for initial qualitative screening of systems that exhibit promising long-term stability, which can be useful to shrink the parameter space for calendar aging studies. By facilitating the identification of improved formulations, this approach can help accelerate innovation in the battery industry.

25 ENERGY STORAGE↗
DOE OSTI2022

Utilization of 29Si MAS-NMR to Understand Solid State Diffusion in Energy Storage Materials

The properties of many solid-state materials arise from critical interfaces tied to the structure, morphology, and composition of the materials under study. For many materials, identifying components that may be invisible to diffraction techniques or other bulk sensitive techniques (i.e. inductively coupled plasma (ICP)), may cause important information to be overlooked. These can include grain boundary phases, nanoscale coatings, amorphous layers, or second phases that influence the materials environment. In this short review, the use of 29 Si MAS NMR as a local probe to detect silicon-containing phases in complex energy storage systems is explored with a focus is on silicon-containing materials and silicon electrodes. Examples highlighting the utility of 29 Si MAS NMR include 1) examining copper diffusion into silicon as a method to create 3 dimensional electrodes, 2) using Mg(II) electrolyte additives to create in-situ nanoscale silicide coatings to inhibit low voltage parasitic side reactions and extend calendar life, and 3) studying the lithiation reactions of passivated silicon on different time scales.

Dogan, Fulya↗
DOE OSTI2020

Polysulfide entrapment and retardation in gel electrolyte Li–S batteries: experiments and modeling

Gelling the electrolyte in lithium–sulfur (Li–S) batteries provides advantages in terms of safety and mitigating polysulfide shuttling leading to reduced side reactions and dendrite growth on the anode side. In the current study, organic and ceramic crosslinkers have been used to improve the entrapment of polysulfides and prevent them from shuttling to the anode side. However, the performance of gel electrolytes is still far from being on par with liquid electrolytes in terms of raw capacity. The discharge curves exhibit an extended first plateau for gel electrolyte batteries compared to liquid electrolytes, showing that polysulfides are better trapped in the gel system. Yet, in the conversion of soluble polysulfides into insoluble polysulfides, the second plateau was delayed. Qualitative and quantitative analysis of the polysulfide diffusion in the liquid electrolyte and gel electrolyte systems were also conducted to predict the relative diffusivity ratio between the liquid electrolyte and gel electrolyte for simulation. To probe what happens at the end of the discharge, where the mass transport in the gel electrolyte appears to be slow, a modified discharge procedure was used where the cell is first paused after discharge and then discharged a second time before recharging normally. Coin cell tests for two gel electrolytes in addition to liquid electrolyte show up to 7% capacity recovery after the pause, which indicates that the diffusion of species during the pause is responsible for the failure recovery. Additionally, the recovery is higher for gel electrolytes compared to liquid, for higher C-rates, and for longer pause times. To better understand this behavior, a Li–S numerical model with mass transport limited reactions was used to examine the polysulfide diffusion coefficients expected in different electrolyte systems. The model is able to reproduce the trends seen in experiments and yields a higher recovery for smaller Li 2 S 4 diffusion coefficients, suggesting that insufficient Li 2 S 4 mass transport is responsible for failure at the end of discharge. By identifying the effect that gel electrolytes have on the state of the battery during discharge using both experimental and simulation methods, this work is a step towards leveraging the advantages of gel electrolytes and mitigating their weaknesses.

25 ENERGY STORAGE↗
DOE OSTI2023

Mixed-Anion Contact Ion-Pair Formation Enabling Improved Performance of Halide-Free Mg-Ion Electrolytes

In this article, discovery of stable and efficient electrolytes that are compatible with magnesium metal anodes and high-voltage cathodes is crucial to enabling energy storage technologies that can move beyond existing Li-ion systems. Many promising electrolytes for magnesium anodes have been proposed with chloride-based systems at the forefront; however, Cl-containing electrolytes lack the oxidative stability required by high-voltage cathodes. In this work, we report magnesium trifluoromethanesulfonate (triflate) as a viable coanion for Cl-free, mixed-anion magnesium electrolytes. The addition of triflate to electrolytes containing bis(trifluoromethane sulfonyl) imide (TFSI – ) anions yields significantly improved Coulombic efficiency, up to a 100 mV decrease in the plating/stripping overpotential, improved tolerance to trace H 2 O, and improved oxidative stability (0.35 V improvement compared to that of hybrid TFSI-Cl electrolytes). Based on 19 F nuclear magnetic resonance and Raman spectroscopy measurements, we propose that these improvements in performance are driven by the formation of mixed-anion contact ion pairs, where both triflate and TFSI – are coordinated to Mg 2+ in the electrolyte bulk. The formation of this mixed-anion magnesium complex is further predicted by the density functional theory to be thermodynamically driven. Collectively, this work outlines the guiding principles for the improved design of next-generation electrolytes for magnesium batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Pd-Ru pair on Pt surface for promoting hydrogen oxidation and evolution in alkaline media

Hydrogen oxidation reaction in alkaline media is critical for alkaline fuel cells and electrochemical ammonia compressors. The slow hydrogen oxidation reaction in alkaline electrolytes requires large amounts of scarce and expensive platinum catalysts. While transition metal decoration can enhance Pt catalysts’ activity, it often reduces the electrochemical active surface area, limiting the improvement in Pt mass activity. Here, we enhance Pt catalysts’ activity without losing surface-active sites by using a Pd-Ru pair. Utilizing a mildly catalytic thermal pyrolysis approach, Pd-Ru pairs are decorated on Pt, confirmed by extended X-ray absorption fine structure and high-angle annular dark-field scanning transmission electron microscopy. Density functional theory and ab-initio molecular dynamics simulations indicate preferred Pd and Ru dopant adsorption. The Pd-Ru decorated Pt catalyst exhibits a mass-based exchange current density of 1557 ± 85 A g –1 metal for hydrogen oxidation reaction, demonstrating superior performance in an ammonia compressor.

25 ENERGY STORAGE↗
DOE OSTI2025

Single-Ion Conducting Polymer Electrolyte Enabled via Aza-Michael Addition

Single-ion conducting polymer electrolytes present a possible route for achieving high energy density next-generation batteries due to their flexible nature and high cation transport number. The trifluoromethanesulfonimide (TFSI) functional group represents one of the most efficient tethered anions for Li-ion conductivity. However, the covalent attachment of TFSI groups into polymer electrolytes has been challenging and costly due to its synthetic difficulty and limited commercial availability of building blocks. Here, we present a new polymer electrolyte synthesized by the Michael addition reaction between poly(allylamine) (PAA) and a vinyl TFSI anion under mild reaction conditions. The resulting PAATFSI exhibits a lower glass transition temperature and several orders of magnitude higher Li-ion conductivity than similar TFSI-based single-ion conducting homopolymers in the dry state. Moreover, PAATFSI exhibits excellent Li-ion conductivity (2.7 × 10 –4 S/cm at 30 °C) with the addition of a plasticizer (60 wt % of carbonate solvent), which enables stable lithium–metal battery performance. In conclusion, this study demonstrates a facile route for the synthesis of new single-ion conducting polymer electrolytes that opens a library of possibilities to enable the realization of polymer-based batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

Boosting the Oxygen Evolution Reaction by Tuning the Interfacial Iron Adsorption on Layered Double Hydroxide

Understanding the interaction between ions in the electrolyte and electrode materials plays an important role in optimizing the water electrolysis performance for hydrogen production. Herein, the synergistic effect of iron (Fe) in the electrolyte and interlayer anions within the layered structure on the oxygen evolution reaction (OER) has been investigated by combining material synthesis with controlled structure, multiple characterization techniques, and first-principles calculations. Nickel aluminum layered double hydroxides (NiAl-LDHs) with different interlayer anions (CO 3 2– , Cl – , and Br – ) show similar oxygen evolution activity in the absence of Fe species in the electrolyte. The addition of Fe into the electrolyte results in improved performance for all of the NiAl-LDHs, following the rank LDH-Br > LDH-Cl > LDH-CO 3 , under all of the conditions with varied concentration of Fe. X-ray absorption spectroscopy and identical location electron microscopy analyses show that the LDH structure remains unchanged after the OER activity test, while in situ stationary probe rotating disk electrode inductively coupled plasma mass spectrometry (SPRDE-ICP-MS) measurements show partial dissolution of the intercalating halide ions during cycling, with less dissolution for Br-intercalated materials. Insights from theoretical calculations demonstrate the thermodynamic preference of Br – to remain intercalated in the presence of Fe, while the stronger adsorption of Fe(OH) 3 species on the LDH-Br sample promotes the OER activity. In conclusion, these results provide mechanistic insights into the rational design of active layered materials with an enhanced OER performance for efficient water electrolysis.

58 GEOSCIENCES↗