Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electrode microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Laser ablation of high-loading Li-ion battery electrodes improves accessible capacity and cycle life for Behind-the-Meter Storage

Adoption of Behind-the-Meter Storage (BTMS) requires design of batteries that enable high safety, long cycle life, and low cost at the system level. Pairing Li 4 Ti 5 O 12 (LTO) with LiMn 2 O 4 (LMO) achieves targets related to safety and cycle life, but these materials' low energy densities contribute to higher cost at the system scale. Increasing electrode loading is a simple approach to improve energy density, but comes with a trade-off in electrode utilization due to long, tortuous Li + diffusion pathways. Here, laser ablation is used to microstructure (pattern) high-loading electrodes to enhance electrode performance through improved Li + diffusion pathways. Four cell types, comprising combinations of standard or patterned anode and cathode, were prepared to evaluate the effects of laser ablation at each electrode. A rate test shows that patterning electrodes enhances active material utilization at ≳1C rates. Patterning the cathode yields the most benefit, as cells with a patterned cathode demonstrate a ~20% higher accessible capacity than those without at 1.4C. Additionally, 1C capacity retention of cells with patterned cathode (91% through 3000 cycles) is significantly improved over cells with only the anode patterned (64%) and non-patterned electrodes (50%). Characterization of post-mortem cells before and after refreshing their electrolyte suggests that 1C capacity retention is improved by mitigation of electrode "dry-out". We hypothesize that the microstructure acts as a reservoir of additional electrolyte, or a path for gas to escape, so that active material remains wetted throughout long-term cycling, and/or the microstructure may reduce localized, gas-forming overpotentials in the high-loading electrode.

25 ENERGY STORAGE↗
DOE OSTI2026

Passivation‐Induced Species Dynamics and Microstructural Evolution in Solid‐State Lithium–Sulfur Cathodes

Solid-state lithium–sulfur (SSLS) batteries offer high theoretical energy density, yet their practical viability is hindered by poor sulfur utilization and limited rechargeability. At the core of this challenge lies the passivating nature of Li 2 S, which restricts ionic and electronic transport, suppresses interfacial activity, and severely impedes the reversibility of electrochemical reactions. In this study, we elucidate the mechanistic origins of these limitations by resolving how charge and discharge species form, grow, and spatially evolve within the cathode microstructure under varied current densities and electrode compositions. By resolving the species distribution at the particle scale and coupling it with Raman spectroscopy and X-ray diffraction, we demonstrate how Li 2 S formation induces localized surface passivation that progressively limits electrochemical accessibility within the cathode microstructure. Sulfur utilization is found to be strongly governed by the interplay between sulfur loading, residual porosity, and interfacial architecture. High sulfur contents result in buried, electrochemically isolated domains due to poor solid electrolyte (SE) percolation, while low sulfur contents trigger SE degradation via parasitic reactions. The resulting sulfur-porosity maps delineate the mechanistic boundaries between reversible and transport-limited regimes, offering actionable design guidance for SSLS cathodes with enhanced sulfur utilization.

electrode microstructure↗
DOE OSTI2024

Forming more and sharper sensing protrusions on graphene-based electrodes through annealing

A better understanding of the microstructure, physicochemical properties, and sensing behavior of an electrode is critical in developing quick, high sensitivity, and robust electrochemical sensors. Here, in this study, a single electrode was fabricated with self-prepared graphene ink through a drop-cast process followed with a subsequent annealing treatment. The graphene ink-based electrodes were characterized through AFM, contact angle, FTIR, impedance spectra, Raman, and SEM to understand annealing treatment effects. The dynamic response of the electrode to humidity, and vapors of ethanol, propanol, or acetone was measured using a four-point probe station in a closed chamber. The annealing treatment increased the conductivity of the electrode and improved its sensing performance by forming more and sharper protrusions on the electrode surface. These unique surface protrusions suggest that the annealed graphene ink-based electrodes hold great potential in developing high-performance electrochemical sensors.

42 ENGINEERING↗
DOE OSTI2022

Interplay of Electrode Heterogeneity and Lithium Plating

Lateral microstructure heterogeneity in anodes is known to induce nonuniform current density, state of charge, and lithium plating. This means that such electrode heterogeneity can limit the fast charging of lithium-ion batteries. In this work, a combination of experiments and simulation is employed to understand the effect of mm scale lateral heterogeneity on cell aging. A previously developed model was extended to efficiently simulate SEI formation and Li plating for independent regions of an electrode. The model consists of three parallel regions each described under a P2D framework and with a distinct ionic resistance and possibly active material loading. The results suggest that during fast charge when the active material is uniformly distributed across the three regions, the region with the highest resistance reaches the end of life sooner than the other regions. There is also positive feedback from Li metal filling the pores near the separator interface that further accelerates lithium plating. Lastly, when there is a non-uniform active material distribution associated with the ionic resistance heterogeneity, tight competition between regions can occur, leading to less overall lithium plating and plating that is more uniform between regions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Dynamic In‐Plane Heterogeneous and Inverted Response of Graphite to Fast Charging and Discharging Conditions in Lithium‐Ion Pouch Cells

Solutions for improving fast charging of lithium‐ion batteries have largely focused on alleviating through‐plane lithiation gradients while little is understood about in‐plane heterogeneities and how to resolve them. Herein, high‐speed synchrotron X‐ray diffraction (XRD) resolves graphite lithiation spatially and temporally during 6 C charging and 2 C discharging. At every point during operation, considerable differences in the state of lithiation across the pouch cell are present. Some regions are more responsive to operation than others, reaching full lithiation early during charge and full delithiation during discharge. Other regions within the cell never fully delithiate during discharge, despite a prolonged voltage hold at 2.8 V. Using time‐resolved XRD data, the calculated local current density (mA cm −2 ) at the graphite surface shows an unexpected occurrence of local inverted current densities where regions of graphite are observed to delithiate during charging and lithiate during discharging. A pseudo‐3D model is developed for the graphite electrode with spatially varying microstructural tortuosity to show how microstructural heterogeneity could influence spatial charge dynamics. The model could not predict the complex in‐plane charge behavior observed within the cell. Consequently physics‐based charging protocols based on homogeneous electrode assumptions may underestimate the local variations in charge dynamics and occurrence of lithium plating.

25 ENERGY STORAGE↗
DOE OSTI2025

Microstructure-based modeling of inner oxygen pressure in solid oxide electrolysis cells: Analysis of electrode delamination and mitigation

One major degradation mechanism during long-term operation of solid oxide electrolysis cells (SOECs) is delamination of oxygen electrodes (OEs). The driving force for the electrode delamination could be the generated high inner oxygen pressure near the electrode-electrolyte interface during operation. However, the effects of transport properties and electrode thickness on the inner oxygen partial pressure are not well understood. Here a microstructure-based electrochemical model, which includes the conduction of electrons and oxygen ions coupled with Butler-Volmer-type chemical reactions at triple-phase-boundaries (TPBs), is employed to investigate the oxygen pressure in lanthanum strontium manganate (LSM)-based SOECs. The model is applied to both two-dimensional (2D) prototype microstructures and three-dimensional (3D) realistic microstructures, and the oxygen pressure is analyzed as a function of transport properties and electrode thickness under both potentiostatic and galvanostatic operations. The simulation results suggest strategies to suppress electrode delamination. The simulation results are compared to an analytical solution, and the discrepancies are attributed to the Butler-Volmer-type kinetics included in the microstructure-based model.

25 ENERGY STORAGE↗
DOE OSTI2021

Indirect electrochemical method for high accuracy quantification of protein adsorption on gold surfaces

We demonstrate the use of copper underpotential deposition (UPD) for measurement of the electrochemically active surface area of a protein-modified gold electrode. The kinetics of adsorption and the subsequent structural rearrangement of β-casein, as a model protein, on the surface of a gold electrode have been followed over time. The protein-free surface area was determined by measuring the charge derived from UPD copper deposition on the non-blocked surface area at different stages of adsorption. The behaviour of β-casein adsorption as a function of surface roughness and the microstructure of the gold electrode, as well as the concentration of the protein solution, are studied using this method.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Transport–Friendly Microstructure in SSC–MEA: Unveiling the SSC Ionomer–Based Membrane Electrode Assemblies for Enhanced Fuel Cell Performance

The significant role of the cathodic binder in modulating mass transport within the catalyst layer (CL) of fuel cells is essential for optimizing cell performance. This investigation focuses on enhancing the membrane electrode assembly (MEA) through the utilization of a short-side-chain perfluoro-sulfonic acid (SSC-PFSA) ionomer as the cathode binder, referred to as SSC-MEA. This study meticulously visualizes the distinctive interpenetrating networks of ionomers and catalysts, and explicitly clarifies the triple-phase interface, unveiling the transport-friendly microstructure and transport mechanisms inherent in SSC-MEA. The SSC-MEA exhibits advantageous microstructural features, including a better-connected ionomer network and well-organized hierarchical porous structure, culminating in superior mass transfer properties. Relative to the MEA bonded by long-side-chain perfluoro-sulfonic acid (LSC-PFSA) ionomer, noted as LSC-MEA, SSC-MEA exhibits a notable peak power density (1.23 W cm –2 ), efficient O 2 transport, and remarkable proton conductivity (65% improvement) at 65 °C and 70% relativity humidity (RH). These findings establish crucial insights into the intricate morphology-transport-performance relationship in the CL, thereby providing strategic guidance for developing highly efficient MEA.

25 ENERGY STORAGE↗
DOE OSTI2020

Advanced oxygen-electrode-supported solid oxide electrochemical cells with Sr(Ti,Fe)O 3–δ -based fuel electrodes for electricity generation and hydrogen production

Sr(Ti 0.3 Fe 0.7 )O 3–δ (STF) and the associated exsolution electrodes Sr 0.95 (Ti 0.3 Fe 0.63 Ru 0.07 )O 3–δ (STFR), or Sr 0.95 (Ti 0.3 Fe 0.63 Ni 0.07 )O 3–δ (STFN) are alternatives to Ni-based cermet fuel electrodes for solid oxide electrochemical cells (SOCs). They can provide improved tolerance to redox cycling and fuel impurities, and may allow direct operation with hydrocarbon fuels. However, such perovskite-oxide-based electrodes present processing challenges for co-sintering with thin electrolytes to make fuel electrode supported SOCs. Thus, they have been mostly limited to electrolyte-supported SOCs. Here, we report the first example of the application of perovskite oxide fuel electrodes in novel oxygen electrode supported SOCs (OESCs) with thin YSZ electrolytes, and demonstrate their excellent performance. The OESCs have La 0.8 Sr 0.2 MnO 3–δ –Zr 0.92 Y 0.16 O 2–δ (LSM–YSZ) oxygen electrode-supports that are enhanced via infiltration of SrTi 0.3 Fe 0.6 Co 0.1 O 3–δ , while the fuel electrodes are either Ni-YSZ, STF, STFN, or STFR. Fuel cell power density as high as 1.12 W cm –2 is obtained at 0.7 V and 800 °C in humidified hydrogen and air with the STFR electrode, 60% higher than the same cell made with a Ni-YSZ electrode. Electrolysis current density as high as –1.72 A cm –2 is obtained at 1.3 V and 800 °C in 50% H 2 O to 50% H 2 mode; the STFR cell yields a value 72% higher than the same cell made with a Ni-YSZ electrode, and competitive with the widely used conventional Ni-YSZ-supported cells. The high performance is due in part to the low resistance of the thin YSZ electrolyte, and also to the low fuel electrode polarization resistance, which decreases with fuel electrode in the order: Ni-YSZ > STF > STFN > STFR. The high performance of the latter two electrodes is due to exsolution of catalytic metal nanoparticles; the results are discussed in terms of the microstructure and properties of each electrode material, and surface oxygen exchange resistance values are obtained over a range of conditions for STF, STFN, and STFN. Furthermore, the STF fuel electrodes also provide good stability during redox cycling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Enable superior performance of ultra-high loading electrodes through the cost-efficient solvent-free electrode manufacturing technology

This research explores an innovative solvent-free method for fabricating ultra-high loading NMC811 and graphite electrodes (~6mAh∙cm -2 ), showcasing remarkable electrochemical performance enhancements compared to the electrodes prepared by the conventional slurry-casting method. Here, the optimized microstructure with dry-printed (DP) electrodes enhanced electrolyte penetration and minimized lithium-ion diffusion tortuosity resulting in improved rate performance at high current rates. Additionally, this innovative electrode manufacturing approach enables more uniform CEI and SEI formation and growth, which effectively doubles the cycle life of single-layer pouch cells with DP electrodes. Beyond the performance enhancements, this method also offers a notable 29.2 % overall cost advantages, potentially revolutionizing future battery manufacturing. The findings presented in this work underscore the potential of solvent-free manufacturing technology as a high-loading capable and cost-efficient path for advanced battery production.

25 ENERGY STORAGE↗
DOE OSTI2023

Quantifying the impact of operating temperature on cracking in battery electrodes, using super-resolution of microscopy images and stereology

There are numerous factors that can have an impact on the degradation behavior of batteries, such as the number of recharge cycles or the charge rate. Here, we investigate the influence of operating temperature on the structural degradation of the microstructure in lithium-ion positive electrodes. For that purpose, the microstructure is characterized for cathodes which have been cycled for 200 cycles under 6C (10-minute) charging at different operating temperatures, namely, 20°C, 30°C, 40°C, and 50°C. For each operating condition scanning electron microscopy (SEM) images of cross-sectioned Li x Ni 0.5 Mn 0.3 Co 0.2 O 2 (NMC532) electrodes have been analyzed, to determine structural descriptors such as global particle porosity, crack size/length/width distribution, and porosity and specific surface area distribution of individual particles. Additionally, a stereological method has been deployed to investigate the local particle porosity as a function of distance to the particle center. Results show that particle porosity increases with increasing cycling temperature. Particle porosity is greatest at the particle center and decreases along the particle radius to the exterior. Particle surface area is similar across the four cycling-temperature aging conditions.

25 ENERGY STORAGE↗
DOE OSTI2023

Enhanced Electrochemical Performance of Disordered Rocksalt Cathodes Enabled by a Graphite Conductive Additive

Cobalt-free cation-disordered rocksalt (DRX) cathodes are a promising class of materials for next-generation Li-ion batteries. Although they have high theoretical specific capacities (>300 mA h/g) and moderate operating voltages (~3.5 V vs Li/Li + ), DRX cathodes typically require a high carbon content (up to 30 wt %) to fully utilize the active material which has a detrimental impact on cell-level energy density. To assess pathways to reduce the electrode’s carbon content, the present study investigates how the carbon’s microstructure and loading (10–20 wt %) influence the performance of DRX cathodes with the nominal composition Li 1.2 Mn 0.5 Ti 0.3 O 1.9 F 0.1 . While electrodes prepared with conventional disordered carbon additives (C65 and ketjenblack) exhibit rapid capacity fade due to an unstable cathode/electrolyte interface, DRX cathodes containing 10 wt % graphite show superior cycling performance (e.g., reversible capacities ~260 mA h/g with 85% capacity retention after 50 cycles) and rate capability (~135 mA h/g at 1000 mA/g). Furthermore, a suite of characterization tools was employed to evaluate the performance differences among these composite electrodes. Overall, these results indicate that the superior performance of the graphite-based cathodes is largely attributed to the: (i) formation of a uniform graphitic coating on DRX particles which protects the surface from parasitic reactions at high states of charge and (ii) homogeneous dispersion of the active material and carbon throughout the composite cathode which provides a robust electronically conductive network that can withstand repeated charge–discharge cycles. Overall, this study provides key scientific insights on how the carbon microstructure and electrode processing influence the performance of DRX cathodes. Based on these results, exploration of alternative routes to apply graphitic coatings is recommended to further optimize the material performance.

25 ENERGY STORAGE↗
DOE OSTI2022

Parametric Study of the Influence of Support Type, Presence of Platinum on Support, and Ionomer Content on the Microstructure of Polymer Electrolyte Fuel Cell Catalyst Layers

We report Ultra-small angle X-ray scattering (USAXS) was employed to investigate the effects of carbon support type, the presence of platinum on carbon, and ionomer loading on the microstructure of polymer electrolyte fuel cell (PEFC) catalyst layers (CLs). Particle size distributions (PSDs), obtained from fitting the measured scattering data were used to interpret the size of carbon aggregates (40–300 nm) and agglomerates (>400 nm) from two-component carbon/ionomer and three-component platinum/carbon/ionomer CLs. Two types of carbon supports were investigated: high surface area carbon (HSC) and Vulcan XC-72. CLs with a range of perfluorosulfonic acid (PFSA) ionomer to carbon (I/C) ratios (0.2–1.2) and also with perfluoroimide acid (PFIA) ionomer were studied to evaluate the effect of ionomer on CL microstructure. The carbon type, the presence of platinum, and ionomer loading were all found to significantly impact carbon agglomeration. The extent of Pt/C agglomeration in the CL was found to increase with increasing ionomer and platinum concentration and to decrease with increasing carbon surface area. Platinum electrochemically-active surface area (ECSA) and local oxygen transport resistance (R nF ) were correlated to the CL microstructure to yield relationships affecting electrode performance.

25 ENERGY STORAGE↗
DOE OSTI2022

Li-Ion Battery Electrode Contact Resistance Estimation by Mechanical Peel Test

Li-ion battery electrode electronic properties, including bulk conductivity and contact resistance, are critical parameters affecting cell performance and fast-charge capability. Contact resistance between the coating and current collector is often the largest electronic resistance in an electrode and is affected by chemical, microstructural, and interfacial variations. Direct measurements of contact resistance and bulk conductivity have proven to be challenging. In their absence, a mechanical electrode peel test is often used to compare adhesion and electrical contact resistance. However, using a micro-flexible-surface probe, contact resistance can be directly determined. Here, this work compares contact resistance and mechanical peel strength of multiple commercial-grade HE5050 and NCM523 cathodes and graphite and silicon anodes. It was found that peel strength correlates well with contact resistance in a carefully curated data set (p < 0.05) and in some situations may be a good metric to estimate electrical properties. However, there were distinct outliers in the data set, indicating that peel strength may not accurately reflect electrical properties when there is significant variation in electrode composition. These results illustrate the value of the micro-flexible-surface probe in quantifying contact resistance and bulk conductivity to better understand how battery composition and processing steps affect microstructure and resulting cell performance.

25 ENERGY STORAGE↗
DOE OSTI2025

Improving durability and performance of solid oxide electrolyzers by controlling surface composition on oxygen electrodes

Solid oxide electrolysis cell (SOEC) is a promising technology for high-efficiency energy conversion, enabling the production of hydrogen, syngas, synthetic fuels, and various commodity chemicals. Unlike traditional thermochemical processes, SOECs operate at elevated temperatures (600-850°C), benefiting from favorable thermodynamics and reaction kinetics. This makes them highly energy efficient compared to alkaline or polymer electrolyte membrane (PEM) electrolysis technologies. However, despite these advantages, SOECs face significant challenges related to performance degradation over time. A primary issue is the degradation of the oxygen electrode due to strontium (Sr) segregation and impurity poisoning from chromium (Cr) and sulfur (S). This is because the pathway to deposition of Cr and S include the reaction of Cr and S with the segregated SrO at the surface. Sr segregation leads to the formation of insulating compounds such as SrCrO4 and SrSO4, which block active sites, reduce oxygen exchange rates, and compromise the electrode's electrochemical stability. The degradation mechanisms involve complex interactions between the electrode material's surface chemistry, microstructure, and the operating environment. Sr segregation is particularly problematic because it facilitates the deposition of Cr and S impurities, exacerbating performance losses. Addressing these issues is critical to enhancing the durability and economic viability of SOEC technology. The primary goal of this project is to improve the durability and performance of SOECs by controlling the surface composition of the oxygen electrode. This is achieved by suppressing Sr segregation, thereby mitigating impurity poisoning pathways. The project aims to enhance the oxygen exchange rate, improve cell stability, and extend the operational lifespan of SOECs without necessitating major changes to electrode chemistry or stack components.

30 DIRECT ENERGY CONVERSION↗