Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electrical conductance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Electrical Conductivity of HgTe at High Temperatures

The electrical conductivity of HgTe was measured using a rotating magnetic field method from 300 K to the melting point (943 K). A microscopic theory for electrical conduction was used to calculate the expected temperature dependence of the HgTe conductivity. A comparison between the measured and calculated conductivities was used to obtain the estimates of the temperature dependence of Gamma(sub 6)-Gamma(sub 8) energy gap from 300 K to 943 K. The estimated temperature coefficient for the energy gap was comparable to the previous results at lower temperatures (less than or equal to 300 K). A rapid increase in the conductivity just above 300 K and a subsequent decrease at 500 K is attributed to band crossover effects. This paper describes the experimental approach and some of the theoretical calculation details.

Li, C.↗

Further efforts to limit lunar internal temperatures from electrical conductivity determinations

A representative set of 18 electrical conductivity profiles consistent with lunar transfer function data in the 0.00001 to 0.001 Hz range is generated by means of a Monte Carlo procedure. Laboratory electrical conductivity vs temperature data extrapolated to lower and higher temperatures are used to convert the 18 profiles into temperature profiles for a series of radially homogeneous olivine-pyroxene mixtures ranging from 100% olivine to 100% aluminous orthopyroxene. The former yields selenotherms approaching the Ringwood-Essene solidus at depths near 500 km, while additions of the latter in concentrations greater than 15-30 vol% leads to cooler selenotherms which approach the solidus only at depths greater than about 1000 km. On the basis of independent geophysical constraints, the profile envelopes for compositions containing more than 15-30 vol% aluminous orthopyroxene are considered to be the most probable.

Hood, L. L.↗

Performance and durability of electrically conductive tape for shingled Si heterojunction technology cells

We report electrically conductive tape (ECT) was characterized and used to assemble shingled cell strings at low temperature to achieve high reliability Pb- and Ag-free interconnections. The volume resistivity for two considered ECTs are 0.13 ± 0.06 mΩ·cm and 0.47 ± 0.20 mΩ·cm and specific contact resistances, 6.85± 2.00 mΩ·cm 2 and 6.30 ± 0.37 mΩ·cm 2 using the emerging IEC 62788-8-1 Technical Specification for assessment of electrically conductive adhesives (ECA). Durability and performance of the technology in glass–glass mini modules were evaluated with temperature cycling, damp heat testing, and combined-accelerated stress testing (CAST). Through temperature cycling (-40°C to 85°C) applying five times the mini module short-circuit current in forward bias and in the multi climate CAST protocol, there was negligible degradation of fill factor after replacing connectors at the modules' cable leads; however, CAST resulted in short circuit current loss attributed to degradation in light collection by the cells, not the ECT. The IEC 61215-2 85°C, 85% relative humidity damp heat testing showed susceptibility of the HJT cells to effects of humidity in the electroluminescence intensity around the module perimeter that degraded power performance by 4% (relative). Contrasting the IEC 61215-2 qualification testing-based damp heat testing with CAST, factors such as the optical stress of CAST may precipitate the degradation of the modules whereas the humidity levels and duration of IEC 61215-2 damp heat testing may lead to excessive levels of humidity diffused into the modules, potentially resulting in degradation that is unrepresentative of the field.

14 SOLAR ENERGY↗

Enhancement of local electrical conductivities in SiC by femtosecond laser modification

Enhancement of local electric conductivities induced by femtosecond laser modification in silicon carbide was studied. Current-voltage (I-V) characteristics of the laser-modified regions were measured between the ion-implanted metal contacts. Interestingly, the resistance sharply decreased in the fluence range from 5.0 to 6.7 J/cm{sup 2}. The resistance at the irradiation fluence of 53 J/cm{sup 2} decreased by more than six orders of magnitude compared with the nonirradiated one. From the I-V characteristics and the scanning electron microscope observations, we conclude that the phase separation associate with the formation of classical laser induced periodic structure causes the drastic increase in electric conductivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Engineering Electrical Conductivity in Stable Zirconium-Based PCN-222 MOFs with Permanent Mesoporosity

Electrically conductive metal–organic frameworks (MOFs) featuring zirconium-based nodes are of great interest for electrochemical and optoelectronic applications due to their exceptional thermal and chemical stability, although the number of such MOFs remains limited. Here in this paper, we demonstrate that electron deficient molecules such as transition metal(IV) bis(dicarbollide) (TM IV (C 2 B 9 H 11 ) 2 ; TM IV CB for short, where TM = Ni, Pd, and Pt) or C 60 , spatially infiltrated in the microporous channels of the zirconium-based porphyrinic MOFs PCN-222 and PCN-222-Zn, generate highly stable and electrically conductive frameworks in which the mesopores remain accessible to other guests. Solid-state density functional theory (DFT) and ab initio molecular dynamics (AIMD) simulations indicate incorporation of Ni IV CB and C 60 in the MOF micropores is energetically and structurally feasible. Interestingly, in contrast to the free species, strong donor–acceptor interactions between the MOF and Ni IV CB restrain it to a single conformation. Calculated electronic structures and charge-hopping conduction probabilities illustrate that efficient charge-transfer (CT) from photoexcited linkers to the guest molecules facilitates charge hopping in the framework, making the MOFs electrically conductive. The donor–acceptor conjugates also enhance exciton dissociation at their heterojunctions, fostering the formation of long-lived electron-trapped states with potential utility for photo- and electrochemical devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Contamination from electrically conductive silicone tubing during aerosol chemical analysis

Electrically conductive silicone tubing is used to minimize losses in sampling lines during the analysis of airborne particle size distributions and number concentrations. We report contamination from this tubing using gas chromatography-mass spectrometry (GC-MS) of filter-collected samples as well as by particle mass spectrometry. Comparison of electrically conductive silicone and stainless steel tubing showed elevated siloxanes only for the silicone tubing. The extent of contamination increased with length of tubing to which the sample was exposed, and decreased with increasing relative humidity.

36 MATERIALS SCIENCE↗

Electrical Conductivity in Textiles

Copper is the most widely used electrical conductor. Like most metals, though, it has several drawbacks: it is heavy, expensive, and can break. Fibers that conduct electricity could be the solutions to these problems, and they are of great interest to NASA. Conductive fibers provide lightweight alternatives to heavy copper wiring in a variety of settings, including aerospace, where weight is always a chief concern. This is an area where NASA is always seeking improved materials. The fibers are also more cost-effective than metals. Expenditure is another area where NASA is always looking to make improvements. In the case of electronics that are confined to small spaces and subject to severe stress, copper is prone to breaking and losing connection over time. Flexible conductive fibers eliminate that problem. They are more supple and stronger than brittle copper and, thus, find good use in these and similar situations. While clearly a much-needed material, electrically conductive fibers are not readily available. The cost of new technology development, with all the pitfalls of troubleshooting production and the years of testing, and without the guarantee of an immediate market, is often too much of a financial hazard for companies to risk. NASA, however, saw the need for electrical fibers in its many projects and sought out a high-tech textile company that was already experimenting in this field, Syscom Technology, Inc., of Columbus, Ohio. Syscom was founded in 1993 to provide computer software engineering services and basic materials research in the areas of high-performance polymer fibers and films. In 1999, Syscom decided to focus its business and technical efforts on development of high-strength, high-performance, and electrically conductive polymer fibers. The company developed AmberStrand, an electrically conductive, low-weight, strong-yet-flexible hybrid metal-polymer YARN.

Source record↗

Interfacial Layer Growth Condition Dependent Electrical Conduction in HfO2/SiO2 Heterostructured Thin Films

The electrical conduction mechanism contributing to the leakage current at different field regions has been studied in this work. The current-voltage (I-V) measurement of TiN/HfO{sub 2}/SiO{sub 2}/P-Si nMOS capacitor has been taken for two different interfacial layer (SiO{sub 2}) growth conditions such as in situ steam grown (ISSG) and chemical processes. It is observed that Poole-Frenkel mechanism is the dominant conduction mechanism in high field region whereas Ohmic conduction is dominant in the low field region. Also it is seen that the gate leakage current is reduced for the devices having chemically grown interfacial layer compared to that of ISSG devices. Both trap energy level ({phi}{sub t}) and activation energy (E{sub a}) increase in the chemically grown interfacial layer devices for the Poole-Frenkel and Ohmic conduction mechanisms respectively in comparison to ISSG devices. Trap energy level ({phi}{sub t}) of {approx} 0.2 eV, obtained from Poole-Frenkel mechanism indicates that the doubly ionized oxygen vacancies (V{sup 2-}) are the active defects and are contributing to the leakage current in these devices.

14 SOLAR ENERGY↗

Reduced de-doping and enhanced electrical conductivity of polyaniline filled phenol-divinylbenzene composite for potential lightning strike protection application

In this study, phenolic resin was mixed with a cross-linking agent divinylbenzene (DVB) to prepare a polyaniline-based electrically-conductive thermosetting polymer composite. It has been shown that this Phenol-DVB mixture can undergo cationic polymerization in the presence of the dodecylbenzene sulfonic acid (DBSA)-doped polyaniline (PANI). Composites with different weight ratios of phenolic resin and DVB were mixed with a fixed weight of DBSA-PANI (i.e. 30 wt. %). Increasing the phenol content in the resin system was found to improve the electrical conductivity of the composite to almost 2700%. This improvement has been assigned to the reduced de-doping of polyaniline in phenol-DVB resin. Active sites of phenol effectively attached to the β carbon of DVB and reduced the proton subtracting species of DVB, leading to reduced de-doping of PANI. This behavior was studied through various characterization techniques including differential scanning calorimetry (DSC), FT-IR spectroscopy and Scanning Electron Microscopy (SEM). Electrical conductivity measurement, mechanical properties, and in-situ electrical conductivity measurements were performed to find the optimized properties of the composite. Optimized composites prepared with the composition of 30 wt. % DBSA-PANI and 70 wt. % of phenol-DVB (50 wt. % each), have shown electrical conductivity of 0.20 S/cm and a flexural modulus of 2.1 GPa, which is a significant improvement in the flexural properties of polymer based-thermosetting composites with similar electrical conductivity. Lastly, this material can be a potential candidate for the lightning strike protection of fiber reinforced plastics.

36 MATERIALS SCIENCE↗

Investigation of the electrical conduction mechanisms in P-type amorphous germanium electrical contacts for germanium detectors in searching for rare-event physics

For the first time, electrical conduction mechanisms in the disordered material system is experimentally studied for p-type amorphous germanium (a-Ge) used for high-purity Ge detector contacts. The localization length and the hopping parameters in a-Ge are determined using the surface leakage current measured from three high-purity planar Ge detectors. The temperature dependent hopping distance and hopping energy are obtained for a-Ge fabricated as the electrical contact materials for high-purity Ge planar detectors. As a result, we find that the hopping energy in a-Ge increases as temperature increases while the hopping distance in a-Ge decreases as temperature increases. The localization length of a-Ge is on the order of 2.13$^{-0.05}_{+0.07}$A° to 5.07$^{0.83}_{+2.58}$A°,depending on the density of states near the Fermi energy level within bandgap. Using these parameters, we predict that the surface leakage current from a Ge detector with a-Ge contacts can be much smaller than one yocto amp (yA) at helium temperature, suitable for rare-event physics searches.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Nanostructured Cu-Cr alloy with high strength and electrical conductivity

The influence of nanostructuring by high pressure torsion (HPT) on strength and electrical conductivity in the Cu-Cr alloy has been investigated. Microstructure of HPT samples was studied by transmission electron microscopy with special attention on precipitation of small chromium particles after various treatments. Effect of dynamic precipitation leading to enhancement of strength and electrical conductivity was observed. It is shown that nanostructuring leads to combination of high ultimate tensile strength of 790–840 MPa, enhanced electrical conductivity of 81%–85% IACS and thermal stability up to 500 °C. The contributions of grain refinement and precipitation to enhanced properties of nanostructured alloy are discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Density, Electrical Conductivity and Viscosity of Hg(sub 0.8)Cd(sub 0.2)Te Melt

The density, viscosity, and electrical conductivity of Hg(sub 0.8)Cd(sub 0.2)Te melt were measures as a function of temperature. A pycnometric method was used to measure the melt density in the temperature range of 1072 to 1122 K. The viscosity and electrical conductivity were determined using a transient torque method from 1068 to 1132 K. The density result from this study is within 0.3% of the published data. However, the current viscosity result is approximately 30% lower than the existing data. The electrical conductivity of Hg(sub 0.8)Cd(sub 0.2)Te melt as a function of temperature, which is not available in the literature, is also determined. The analysis of the temperature dependent electrical conductivity and the relationship between the kinematic viscosity and density indicated that the structure of the melt appeared to be homogeneous when the temperature was above 1090 K. A structural transition occurred in the Hg(sub 0.8)Cd(sub 0.2)Te melt as the temperature was decreased to below 1090 K.

Li, C.↗

Characterization of an electrically conductive proppant for fracture diagnostics

Fracture diagnosis with electromagnetic (EM) and electrical tools requires proppants with high electrical conductivity and mechanical strength. Lab measurements of the electrical and hydraulic conductivity of proppants are critical for selecting the best candidates. Such measurements greatly benefit simulations, field tests, and the ultimate application of such proppants in the field. To that end, a new lab protocol is developed for measuring the electrical and hydraulic conductivity of proppants. The lab setup, which mainly includes a resistivity core holder and a Hassler sleeve core holder, allows for simulation of realistic pressure and temperature conditions when making measurements. Petroleum coke (PC) is proposed as a candidate proppant because of its widespread availability and low cost. Lab measurements show that the effective electrical conductivity of pure PC in a model fracture is approximately 5000 S/m, under a closure stress greater than [Formula: see text] (4000 psi). When PC is mixed with sand, the effective electrical conductivity of the mixture decreases with an increasing weight percentage of sand. Although sand degrades the contact between PC particles, the electrical conductivity stays reasonably high (approximately 1700 S/m) when 50% sand is added. Hydraulic conductivity measurements show that when a fracture is propped with pure PC, the measured fracture conductivity is greater than [Formula: see text] ([Formula: see text]) (dimensionless fracture conductivity greater than 100 for a shale with [Formula: see text] or 100 nD permeability) under a confining pressure of [Formula: see text] (6000 psi). This means that a fracture propped with PC is infinitely conductive in a typical shale formation. When sand is added, the fracture’s hydraulic conductivity becomes even higher, which clearly shows PC’s ability of sustaining high stresses. The proposed protocol provides a robust and effective method that can be generalized for lab testing for other candidate proppants. The data presented clearly show that PC has the potential for field-scale applications in EM hydraulic fracture diagnostics.

Geochemistry & Geophysics↗

Iodine doped carbon nanotube cables exceeding specific electrical conductivity of metals

Creating highly electrically conducting cables from macroscopic aggregates of carbon nanotubes, to replace metallic wires, is still a dream. Here we report the fabrication of iodine-doped, double-walled nanotube cables having electrical resistivity reaching ,1027 V.m. Due to the low density, their specific conductivity (conductivity/weight) is higher than copper and aluminum and is only just below that of the highest specific conductivity metal, sodium. The cables exhibit high current-carrying capacity of 104 ,105 A/cm2 and can be joined together into arbitrary length and diameter, without degradation of their electrical properties. The application of such nanotube cables is demonstrated by partly replacing metal wires in a household light bulb circuit. The conductivity variation as a function of temperature for the cables is five times smaller than that for copper. The high conductivity nanotube cables could find a range of applications, from low dimensional interconnects to transmission lines.

36 MATERIALS SCIENCE↗

Synthesis of novel electrically conducting polymers: Potential conducting Langmuir-Blodgett films and conducting polymers on defined surfaces

Based on previous results involving thiophene derived electrically conducting polymers in which it was shown that thiophene, 3-substituted thiophenes, furans, and certain oligomers of these compounds showed electrical conductivity after polymerization. The conductivity was in the order of up to 500 S/cm. In addition, these polymers showed conductivity without being doped and most of all they were practically inert toward ambient conditions. They even could be used in aqueous media. With these findings as a guide, a number of 3-long-chain-substituted thiophenes and 1-substituted-3-long-chain substituted pyrrols were synthesized as monomers for potential polymeric electrically conducting Langmuir-Blodgett films.

Zimmer, Hans↗

High electrical conductivity and carrier mobility in oCVD PEDOT thin films by engineered crystallization and acid treatment

Air-stable, lightweight, and electrically conductive polymers are highly desired as the electrodes for next-generation electronic devices. However, the low electrical conductivity and low carrier mobility of polymers are the key bottlenecks that limit their adoption. We demonstrate that the key to addressing these limitations is to molecularly engineer the crystallization and morphology of polymers. We use oxidative chemical vapor deposition (oCVD) and hydrobromic acid treatment as an effective tool to achieve such engineering for conducting polymer poly(3,4-ethylenedioxythiophene) (PEDOT). We demonstrate PEDOT thin films with a record-high electrical conductivity of 6259 S/cm and a remarkably high carrier mobility of 18.45 cm 2 V -1 s -1 by inducing a crystallite-configuration transition using oCVD. Subsequent theoretical modeling reveals a metallic nature and an effective reduction of the carrier transport energy barrier between crystallized domains in these thin films. To validate this metallic nature, we successfully fabricate PEDOT-Si Schottky diode arrays operating at 13.56 MHz for radio frequency identification (RFID) readers, demonstrating wafer-scale fabrication compatible with conventional complementary metal-oxide semiconductor (CMOS) technology. The oCVD PEDOT thin films with ultrahigh electrical conductivity and high carrier mobility show great promise for novel high-speed organic electronics with low energy consumption and better charge carrier transport.

36 MATERIALS SCIENCE↗