SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This work demonstrates a series of functionalization methods to enhance the utility of thermoplastic-elastomer derived ordered mesoporous carbons, including chemical activation, heteroatom doping, and the introduction of nanoparticles.
Ultrasoft magnetorheological elastomers (MREs) offer convenient real-time magnetic field control of mechanical properties that provides a means to mimic mechanical cues and regulators of cells in vitro. Here, we systematically investigate the effect of polymer stiffness on magnetization reversal of MREs using a combination of magnetometry measurements and computational modeling. Poly-dimethylsiloxane-based MREs with Young’s moduli that range over two orders of magnitude were synthesized using commercial polymers Sylgard™ 527, Sylgard 184, and carbonyl iron powder. The magnetic hysteresis loops of the softer MREs exhibit a characteristic pinched loop shape with almost zero remanence and loop widening at intermediate fields that monotonically decreases with increasing polymer stiffness. A simple two-dipole model that incorporates magneto-mechanical coupling not only confirms that micrometer-scale particle motion along the applied magnetic field direction plays a defining role in the magnetic hysteresis of ultrasoft MREs but also reproduces the observed loop shapes and widening trends for MREs with varying polymer stiffnesses.
Insights into self-assembly enable the 3D printing of super-soft elastomers at room temperature without solvent.
Ambidirectionality, which is the ability of structural elements to move beyond a reference state in two opposite directions, is common in nature. However, conventional soft materials are typically limited to a single, unidirectional deformation unless complex hybrid constructs are used. We exploited the combination of mesogen self-assembly, polymer chain elasticity, and polymerization-induced stress to design liquid crystalline elastomers that exhibit two mesophases: chevron smectic C (cSmC) and smectic A (SmA). Inducing the cSmC-SmA–isotropic phase transition led to an unusual inversion of the strain field in the microstructure, resulting in opposite deformation modes (e.g., consecutive shrinkage or expansion and right-handed or left-handed twisting and tilting in opposite directions) and high-frequency nonmonotonic oscillations. Further, this ambidirectional movement is scalable and can be used to generate Gaussian transformations at the macroscale.
A scintillating material that is a radiation hardened plastic and flexible elastomer is disclosed. The material is useful in a wide range of high energy particle environments and can be used to create detectors. Such detectors can be used in physics experiments or in medical treatment or imaging. The scintillator can be radiation hardened so as to allow for an extended lifetime over other materials.
A method of forming a three-dimensional structure of liquid crystal (LC) elastomers includes contacting a resin layer of LC oligomers with a layer of photoalignment material, and exposing a portion of photoalignment material to light for aligning the portion of photoalignment material in a first orientation. The LC oligomers adjacent the illuminated portion of photoalignment material align to the first orientation of the illuminated portion. The portion of aligned LC oligomers of the resin layer are cured. Operations for forming additional layers include creating a relative movement of the resin layer away from the photoalignment material, contacting another resin layer with the photoalignment material, and exposing another portion of photoalignment material to light for aligning the photoalignment material in a different orientation. The LC oligomers adjacent the illuminated portion of photoalignment material align to the different orientation, and the portion of aligned LC oligomers of the resin layer are cured.
Abstract Polymer semiconductors (PSCs) are essential active materials in mechanically stretchable electronic devices. However, many exhibit low fracture strain due to their rigid chain conformation and the presence of large crystalline domains. Here, a PSC/elastomer blend, poly[((2,6‐bis(thiophen‐2‐yl)‐3,7‐bis(9‐octylnonadecyl)thieno[3,2‐b]thieno[2′,3′:4,5]thieno[2,3‐d]thiophene)‐5,5′‐diyl)(2,5‐bis(8‐octyloctadecyl)‐3,6‐di(thiophen‐2‐yl)pyrrolo[3,4‐c]pyrrole‐1,4‐dione)‐5,5′‐diyl]] (P2TDPP2TFT4) and polystyrene‐ block ‐poly(ethylene‐ran‐butylene)‐ block ‐polystyrene (SEBS) are systematically investigated. Specifically, the effects of molecular weight of both SEBS and P2TDPP2TFT4 on the resulting blend morphology, mechanical, and electrical properties are explored. In addition to commonly used techniques, atomic force microscopy‐based nanomechanical images are used to provide additional insights into the blend film morphology. Opposing trends in SEBS‐induced aggregation are observed for the different P2TDPP2TFT4 molecular weights upon increasing the SEBS molecular weight from 87 to 276 kDa. Furthermore, these trends are seen in device performance trends for both molecular weights of P2TDPP2TFT4. SEBS molecular weight also has a substantial influence on the mesoscale phase separation. Strain at fracture increases dramatically upon blending, reaching a maximum value of 640% ± 20% in the blended films measured with film‐on‐water method. These results highlight the importance of molecular weight for electronic devices. In addition, this study provides valuable insights into appropriate polymer selections for stretchable semiconducting thin films that simultaneously possess excellent mechanical and electrical properties.
The H2@Scale program of the U.S. Department of Energy (DOE) Fuel Cell Technologies Office is supporting work on the hydrogen compatibility of polymers to improve the durability and reliability of materials for hydrogen infrastructure. The hydrogen compatibility program (H-Mat) seeks “to address the challenges of hydrogen degradation by elucidating the mechanisms of hydrogen-materials interactions with the goal of providing science-based strategies to design materials, (micro)structures, and morphology with improved resistance to hydrogen degradation.” This research has observed interactions of hydrogen and pressure with model rubber-material compounds resulting in volume change and compression-set differences in the materials. The materials were investigated using helium-ion microscopy (HeIM), which revealed significant morphological changes in the plasticizer-incorporating compounds after exposure, as evidenced by time-of-flight secondary ion mass spectrometry. Additional studies using transmission electron microscopy and nuclear magnetic resonance were performed to correlate morphological change to potential chemical change in the materials.
Not Available
Connecting polymer synthesis and processing is an important challenge for streamlining the manufacturing of polymeric materials. In this work, the automated synthesis of acrylate-capped polyurethane oligomers is integrated with vat photopolymerization 3D printing. This strategy enabled the rapid manufacturing of a library of polyurethane-based elastomeric materials with differentiated thermal and mechanical properties. The automated semi-continuous batch synthesis approach proved enabling for resins with otherwise short shelf lives because the intimate connection between synthesis, formulation, and processing. Structure-property studies demonstrated the ability to tune properties through systematic alteration of crosslink density and chemical composition.
Explore the source record for details and available documents.
Segmented polyureas (PUa) are industrially important class of polymers widely used in coatings, sealant, and adhesive applications. Here, in this paper, we report synthesis, characterization, and modeling of Isophorone Diisocyanate-Diethyl-Toluene-Diamine-Polyether amine (IPDI-DETDA-PO PUa) with varied hard segment contents of 20, 30, and 40 weight percent. For each of the three materials, we study its structure and phase behavior using FTIR, DSC, and TEM, and clearly show the presence of microphase separation between the hard and soft nanodomains. We then measure the linear viscoelastic response of the PUa-s using DMA (frequency sweeps at multiple temperatures). The DMA data are shown to obey the time-temperature superposition. Finally, we develop a new micromechanical model describing the DMA results; the model describes a phase-separated PUa as two “Fractional-order Maxwell gels” branches, connected in parallel, with the first FMG branch representing the “percolated hard phase" and the second one modeling the “filled soft phase". In agreement with the earlier thermodynamic theories, the volume-fraction of the percolated hard phase is related to the hard segment weight-fraction (HSWF), defined as the combined mass of IPDI and DETDA normalized to the total mass of the polymer. The data and model are found to be in a good qualitative and quantitative agreement.
Abstract not provided.
Not Available
Not Available