Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dynamic measurements”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Exploratory evaluation of a moving-model technique for measurement of dynamic ground effects

An attempt is presently made to measure the dynamic or time-dependent ground effects that may be encountered by aircraft during approach and landing by means of a ground-based testing technique that employs a model moving horizontally over an upwardly inclined ground plane to simulate the rate of descent. Results have been thus obtained for a 60-deg delta wing and for an F-18 full configuration, with and without thrust reversal, at forward speeds of up to 100 ft/sec. An analysis of the results gathered indicates that ground effects were reduced when the rate of descent was included in the test conditions.

Kemmerly, Guy T.↗
NASA NTRS1985

Correlation of dynamic dielectric measurements with viscosity in polymeric resin systems

Dynamic dielectric analysis has been used to study curing polymer systems and thermoplastics. Measurements have been made over a frequency range of six decades. This wide range of frequencies increases the amount of information which can be obtained. The data are analyzed in terms of the frequency dependence of the specific conductivity sigma and the relaxation time tau, parameters which are characteristic of the cure state of the material and independent of size of the sample. Dynamic dielectric measurements have been correlated with viscosity for the polysulfone thermoplastic UDEL-P1700 and with viscosity and ultrasonic measurements on the DGEBA-type epoxy Epon 828 cured with Agent U. The experimental results suggest that when ionic processes dominate the dielectric response, the intensive property sigma is a good monitor of the resin's viscosity. The results show that the dielectric relaxation time tau can be used to monitor the state of the system and the extent and rate of the reaction.

Kranbuehl, D.↗
DOE OSTI2026

Measurement-informed Dynamic Aggregation of Distribution Systems

This paper proposes a measurement-informed dynamic aggregation methodology in order to create equivalent representations of distribution systems that are compatible with large-scale transmission analysis. By optimizing an equivalent feeder parameters using time-series measurements of active power, reactive power, and voltage at the Point of Interconnection (POI), the approach yields simplified yet dynamically accurate equivalents. Implemented in PSCAD with models of photovoltaic–battery systems, three-phase motors, and static loads, the method employs hybrid differential evolution and bounded least-squares optimization laying the foundation for for real-time state estimation and optimized sensor placement in distribution networks.

Ahmed, Kazi Ishrak [University of Tennessee, Knoxv↗
DOE OSTI2022

Temperature and Dynamic Strain Measurements Using a Single SAWR Sensor

Dynamic strain sensing is relevant in numerous applications involving structural health monitoring, condition-based maintenance, operation efficiency preservation, and work environment safety. These sensors are particularly critical for high-temperature (HT) harsh-environment (HE) industries such as aerospace, automotive, power plants, and advanced manufacturing. In HT/HE, sensor implementation and measurement present challenges such as maintaining sensor stability, accounting for temperature cross-sensitivity, providing HT attachment, and packaging of the sensors and system. Surface acoustic wave resonator (SAWR) sensors can address these needs and offer additional benefits such as compact size and wireless interrogation capability. The SAWR sensitivity to dynamic strain is temperature dependent, making it necessary to measure the sensor temperature in order to use the correct dynamic strain calibration curve. In this work, a method for determining the temperature, dynamic strain magnitude, and dynamic strain spectral components using a single SAWR sensor is presented. Here, the established technique for determining operational temperature and dynamic strain magnitude/spectral components using only one SAWR simplifies the sensor measurement system, thus being very attractive for HT /HE applications.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

An error-in-constitutive equations strategy for topology optimization for frequency-domain dynamics

This paper presents a topology optimization formulation for frequency-domain dynamics to reduce solution dependence upon initial guess and considered loading conditions. Due to resonance phenomena in undamped steady-state dynamics, objectives measuring dynamic response possess many local minima that may represent poor solutions to a design problem, an issue exacerbated for design with respect to multiple frequencies. In this work, we propose an extension of the modified error-in-constitutive-equations (MECE) method, used previously in material identification inverse problems, as a new approach for frequency-domain dynamics topology optimization to mitigate these issues. The main idea of the proposed framework is to incorporate an additional penalty-like term in the objective function that measures the discrepancy in the constitutive relations between stresses and strains and between inertial forces and displacements. Then, the design problem is cast within a PDE-constrained optimization formulation in which we seek displacements, stresses, inertial forces, and a density-field solution that minimize our new objective subject to conservation of linear momentum plus some additional constraints. We show that this approach yields superior designs to conventional gradient-based optimization approaches that solely use a functional of displacements as the objective, while strictly enforcing the constitutive equations. The MECE strategy integrates into a density-based topology optimization scheme for void–solid or two-phase material structural design. We highlight the merits of our approach in a variety of scenarios for direct frequency response design, considering multiple frequency load cases and structural objectives.

42 ENGINEERING↗
NASA NTRSDate not supplied

Practical Considerations using Weighted-Acceleration Compensation Techniques for Dynamic Force Measurements in Wind Tunnels

Most wind tunnel force measurement systems are designed and calibrated for high-accuracy static measurements, but may have limited ability to sense dynamic forces and moments. As a means to improve the measurement bandwidth of dynamic forces, researchers have proposed using a weighted-acceleration technique, which uses accelerometer data to compensate and correct for system dynamics. The sum of weighted-accelerations method is attractive as the acceleration data applies a correction to the traditional static measurements. The focus of this paper is on practical aspects of implementing a weighted-acceleration technique in an experimental arrangement. A formulation of the weighted-acceleration methodology is validated on a reduced-order model and demonstrated on a tabletop experiment that serves as a proxy to a wind tunnel force measurement system. As part of this system, a two component normal force and pitching moment balance was designed and fabricated. A static and dynamic calibration of the system was performed, and the weighted-acceleration technique was used to reconstruct impact forces acting on the system. Practical considerations of the experimental design that improve the success of the methodology are discussed.

Dynamic force measurement↗
NASA NTRSDate not supplied

Practical Considerations using Weighted-Acceleration Compensation Techniques for Dynamic Force Measurements in Wind Tunnels

Most wind tunnel force measurement systems are designed and calibrated for high-accuracy static measurements, but may have limited ability to sense dynamic forces and moments. As a means to improve the measurement bandwidth of dynamic forces, researchers have proposed using a weighted-acceleration technique, which uses accelerometer data to compensate and correct for system dynamics. The sum of weighted-accelerations method is attractive as the acceleration data applies a correction to the traditional static measurements. The focus of this paper is on practical aspects of implementing a weighted-acceleration technique in an experimental arrangement. A formulation of the weighted-acceleration methodology is validated on a reduced-order model and demonstrated on a tabletop experiment that serves as a proxy to a wind tunnel force measurement system. As part of this system, a two component normal force and pitching moment balance was designed and fabricated. A static and dynamic calibration of the system was performed, and the weighted-acceleration technique was used to reconstruct impact forces acting on the system. Practical considerations of the experimental design that improve the success of the methodology are discussed.

Dynamic force measurement↗
NASA NTRS2006

Molecular Rayleigh Scattering Diagnostic for Dynamic Temperature, Velocity, and Density Measurements

A molecular Rayleigh scattering technique is developed to measure dynamic gas temperature, velocity, and density in unseeded turbulent flows at sampling rates up to 16 kHz. A high power CW laser beam is focused at a point in an air jet plume and Rayleigh scattered light is collected and spectrally resolved. The spectrum of the light, which contains information about the temperature and velocity of the flow, is analyzed using a Fabry-Perot interferometer. The circular interference fringe pattern is divided into four concentric regions and sampled at 1 and 16 kHz using photon counting electronics. Monitoring the relative change in intensity within each region allows for measurement of gas temperature and velocity. Independently monitoring the total scattered light intensity provides a measure of gas density. A low speed heated jet is used to validate the measurement of temperature fluctuations and an acoustically excited nozzle flow is studied to validate velocity fluctuation measurements. Power spectral density calculations of the property fluctuations, as well as mean and fluctuating quantities are presented. Temperature fluctuation results are compared with constant current anemometry measurements and velocity fluctuation results are compared with constant temperature anemometry measurements at the same locations.

Mielke, Amy R.↗
NASA NTRS1995

FIR line profiles as probes of warm gas dynamics

Measurements of the shapes, velocities, and intensities of FIR lines all help to probe the dynamics, physical associations, and excitation conditions of warm gas in molecular clouds. With this in mind, we have observed the J=9-8, 12-11,14-13, and 16-15 lines of (12)CO and the 158 micron line of C II in a number of positions in 4 selected clouds. The data were obtained with a laser heterodyne spectrometer aboard NASA's Kuiper Airborne Observatory. Line measurements at 0.6 km/s resolution allow us to resolve the profiles completely, and thereby to distinguish between UV-and shock-heating mechanisms for the high-excitation gas. For CO, the high-J linewidths lie in the range of 4-20 km/s (FWHM), similar to those observed for low-J (J less than 4) transitions in these sources. This correspondence suggests that the hotter gas (T = 200-600 K) is dynamically linked to the quiescent gas component, perhaps by association with the UV-heated peripheries of the numerous cloud clumps. Much of the C II emission is thought to emanate from these cloud peripheries, but the line profiles generally do not match those seen in CO. None of the observed sources show any evidence in high-J (12)CO emission for shock-excitation (i.e., linewidths greater than 30 km/s).

Betz, A. L.↗
NASA NTRS1990

External nozzle flap dynamic load measurements on F-15 S/MTD model

Dynamic pressure loads were obtained on 1/12 scale models of the F-15B production aircraft and the F-15 S/MTD experimental aircraft with rectangular nozzles and canards. Flight Mach numbers from 0.51 to 1.20 were studied for aircraft angles of attack from 0 to 10 deg and nozzle pressure ratios from 1.00 to 5.09. The results show that dynamic levels are lower in the internozzle region of twin rectangular nozzles than are levels found with twin axisymmetric nozzles. At other locations, the levels associated with both geometries are of the same order of magnitude when normalized by aircraft dynamic Q. At Mach number of 0.51, the loads spectrum is dominated by plume shock noise processes for both geometries. Above Mach 0.51, this mechanism is associated with either vortex bursting from a forward location or turbulent boundary layer separation over the nozzle external flaps. At supersonic speeds both geometries show significantly decreased load levels.

Seiner, John M.↗
NASA NTRS1976

Objective and automated measurement of dynamic vision functions

A phoria stimulus array and electro-oculographic (EOG) arrangements for measuring motor and sensory responses of subjects subjected to stress or drug conditions are described, along with experimental procedures. Heterophoria (as oculomotor function) and glare recovery time (time required for photochemical and neural recovery after exposure to a flash stimulus) are measured, in research aimed at developing automated objective measurement of dynamic vision functions. Onset of involuntary optokinetic nystagmus in subjects attempting to track moving stripes (while viewing through head-mounted binocular eyepieces) after exposure to glare serves as an objective measure of glare recovery time.

Flom, M. C.↗
NASA NTRS2001

Dynamic Deformation Measurements of an Aeroelastic Semispan Model

The techniques used to acquire, reduce, and analyze dynamic deformation measurements of an aeroelastic semispan wind tunnel model are presented. Single-camera, single-view video photogrammetry (also referred to as videogrammetric model deformation, or VMD) was used to determine dynamic aeroelastic deformation of the semispan 'Models for Aeroelastic Validation Research Involving Computation' (MAVRIC) model in the Transonic Dynamics Tunnel at the NASA Langley Research Center. Dynamic deformation was determined from optical retroreflective tape targets at five semispan locations located on the wing from the root to the tip. Digitized video images from a charge coupled device (CCD) camera were recorded and processed to automatically determine target image plane locations that were then corrected for sensor, lens, and frame grabber spatial errors. Videogrammetric dynamic data were acquired at a 60-Hz rate for time records of up to 6 seconds during portions of this flutter/Limit Cycle Oscillation (LCO) test at Mach numbers from 0.3 to 0.96. Spectral analysis of the deformation data is used to identify dominant frequencies in the wing motion. The dynamic data will be used to separate aerodynamic and structural effects and to provide time history deflection data for Computational Aeroelasticity code evaluation and validation.

Graves, Sharon S.↗
NASA NTRS1986

A data base and analysis program for shuttle main engine dynamic pressure measurements. Appendix C: Data base plots for SSME tests 902-214 through 902-314

A dynamic pressure data base and data base management system developed to characterize the Space Shuttle Main Engine (SSME) dynamic pressure environment is reported. The data base represents dynamic pressure measurements obtained during single engine hot firing tests of the SSME. Software is provided to permit statistical evaluation of selected measurements under specified operating conditions. An interpolation scheme is included to estimate spectral trends with SSME power level. Flow Dynamic Environments in High Performance Rocket Engines are described.

Coffin, T.↗
NASA NTRS1986

A data base and analysis program for shuttle main engine dynamic pressure measurements. Appendix B: Data base plots for SSME tests 901-290 through 901-414

A dynamic pressure data base and data base management system developed to characterize the Space Shuttle Main Engine (SSME) dynamic pressure environment is described. The data base represents dynamic pressure measurements obtained during single engine hot firing tesets of the SSME. Software is provided to permit statistical evaluation of selected measurements under specified operating conditions. An interpolation scheme is also included to estimate spectral trends with SSME power level. Flow dynamic environments in high performance rocket engines are discussed.

Coffin, T.↗
NASA NTRS1956

A Wind-tunnel Test Technique for Measuring the Dynamic Rotary Stability Derivatives at Subsonic and Supersonic Speeds

A method is described for measuring the dynamic stability derivatives of a model airplane in a wind tunnel. The characteristic features of this system are that single-degree-of-freedom oscillations were used to obtain combinations of rolling, yawing and pitching motions; that the oscillations were excited and controlled by velocity feedback which permitted operation under conditions unfavorable for more conventional types of oscillatory testing; and that data processing was greatly simplified by using analog computer elements in the strain-gage circuitry. A small number of experimental data are included to illustrate the general scope of results obtainable with this system.

Beam, Benjamin H↗
NASA NTRS1986

A data base and analysis program for shuttle main engine dynamic pressure measurements. Appendix F: Data base plots for SSME tests 750-120 through 750-200

A dynamic pressure data base and data base management system developed to characterize the Space Shuttle Main Engine (SSME) dynamic pressure environment is presented. The data base represents dynamic pressure measurements obtained during single engine hot firing tests of the SSME. Software is provided to permit statistical evaluation of selected measurements under specified operating conditions. An interpolation scheme is also included to estimate spectral trends with SSME power level.

Coffin, T.↗