Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dry processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Internally coated air-cooled gas turbine blading

Ten candidate modified nickel-aluminide coatings were developed using the slip pack process. These coatings contain additives such as silicon, chromium and columbium in a nickel-aluminum coating matrix with directionally solidified MAR-M200 + Hf as the substrate alloy. Following a series of screening tests which included strain tolerance, dynamic oxidation and hot corrosion testing, the Ni-19A1-1Cb (nominal composition) coating was selected for application to the internal passages of four first-stage turbine blades. Process development results indicate that a dry pack process is suitable for internal coating application resulting in 18 percent or less reduction in air flow. Coating uniformity, based on coated air-cooled blades, was within + or - 20 percent. Test results show that the presence of additives (silicon, chromium or columbium) appeared to improve significantly the ductility of the NiA1 matrix. However, the environmental resistance of these modified nickel-aluminides were generally inferior to the simple aluminides.

Hsu, L.↗
NASA NTRSDate not supplied

Ultrahigh Areal Capacity Holey Graphene Air Cathodes for Li-O2 and Li-CO2 Batteries

Advanced lithium (Li) batteries using gaseous cathode reactants such as oxygen (O2) and carbon dioxide (CO2)are attractive energy storage platforms because the gases are obtained externally and thus not accounted for in the total battery weight when fully charged.The discharge products at the cathode, typically Li2O2 for Li-O2 batteries and Li2CO3 for Li-CO2 batteries, are insoluble in the electrolyte.Therefore, in order for such batteries to function properly, an “air cathode”,which is a conductive scaffold within the battery cell,is required as a physical location for cathode electrochemical reactions to occur. Prior research has identified many carbon nanomaterials such as carbon nanotubes and graphene as viable choices for air cathode scaffold, while various metallic and metal-free catalytic systems integrated onto carbon-based air cathodes have been developed to improve the sluggish discharge and charge reactions. For future practical applications, the air cathode must exhibit a usable capacity per unit electrode area, or areal capacity, a critical parameter that has been largely overlooked so far in this field. In order to achieve high areal capacity, the air cathode must exhibit a sufficient amount of accessible void volume per unit electrode area while maintaining the conductive scaffold integrity during the entire electrochemical process. Here we present an ultrathick,holey graphene-based air cathode platform fabricated from a facile dry compression process that exhibits remarkable areal capacity values. Holey graphene is a carbon nanomaterial derived from graphene, but with nanometer sized holes through the nanosheet thickness.The presence of these holes enhances mass transport through electrode thickness and also enables the unique dry-press fabrication process that is not achievable using other carbon scaffold materials.The dry-pressed holey graphene air cathode platform is not only compatible with catalyst incorporation to improve battery reaction kinetics, but also allows for novel engineering of electrode architectures that is not achievable using conventional electrode fabrication approaches.The applications of such highly versatile, ultrahigh areal capacity air cathode platforms to both Li-O2 and Li-CO2 battery chemistries will be discussed.

Li-O2 batteries, Li-CO2 batteries, holey graphene,↗
NASA NTRS2007

Fabrication of Polyimide-Matrix/Carbon and Boron-Fiber Tape

The term HYCARB denotes a hybrid composite of polyimide matrices reinforced with carbon and boron fibers. HYCARB and an improved process for fabricating dry HYCARB tapes have been invented in a continuing effort to develop lightweight, strong composite materials for aerospace vehicles. Like other composite tapes in this line of development, HYCARB tapes are intended to be used to build up laminated structures having possibly complex shapes by means of automated tow placement (ATP) - a process in which a computer-controlled multiaxis machine lays down prepreg tape or tows. The special significance of the present process for making dry HYCARB for ATP is that it contributes to the reduction of the overall cost of manufacturing boron-reinforced composite-material structures while making it possible to realize increased compression strengths. The present process for making HYCARB tapes incorporates a "wet to dry" process developed previously at Langley Research Center. In the "wet to dry" process, a flattened bundle of carbon fiber tows, pulled along a continuous production line between pairs of rollers, is impregnated with a solution of a poly(amide acid) in N-methyl-2-pyrrolidinone (NMP), then most of the NMP is removed by evaporation in hot air. In the present case, the polyamide acid is, more specifically, that of LaRC. IAX (or equivalent) thermoplastic polyimide, and the fibers are, more specifically, Manganite IM7 (or equivalent) polyacrylonitrile- based carbon filaments that have a diameter of 5.2 m and are supplied in 12,000-filament tows. The present process stands in contrast to a prior process in which HYCARB tape was made by pressing boron fibers into the face of a wet carbon-fiber/ poly(amide acid) prepreg tape . that is, a prepreg tape from which the NMP solvent had not been removed. In the present process, one or more layer(s) of side-by-side boron fibers are pressed between dry prepreg tapes that have been prepared by the aforementioned gwet to dry h process. The multilayer tape is then heated to imidize the matrix material and remove most of the remaining solvent, and is pressed to consolidate the multiple layers into a dense tape. For tests, specimens of HYCARB tapes and laminated composite panels made from HYCARB tape were prepared as follows: HYCARB tapes were fabricated as described above. Each panel was made by laying down ten layers of tape, containing, variously, one, two, or three boron-fiber plies and the remainder carbon- fiber-only plies (see figure). Each panel was made by laying down ten layers of tape. Each panel was then cured by heating to a temperature of 225 C for 15 minutes, then pressing at 200 psi (A1.4 MPa) while heating to 371 C, holding at 371 C for 1 hour, then continuing to hold pressure during cooling. Control specimens that were otherwise identical except that they did not contain boron fibers also were prepared. In room-temperature flexural tests, the HYCARB specimens performed comparably to the control specimens; in room-temperature, open-hole compression tests, the HYCARB specimens performed slightly better, by amounts that increased with boron content.

Belvin, Harry L.↗
NASA NTRS2002

Development of a New Membrane Casting Apparatus for Studying Macrovoid Defects in Low-G

A new membrane-casting apparatus is developed for studying macrovoid defects in polymeric membranes made by the wet- and dry-casting process in low-gravity. Macrovoids are large (10-50 micron), open cavities interspersed among the smaller pores in the substructure under the gelled skin surface layer of the cast membrane. Although their occurrence is considered endemic to the wet- and dry-casting process since they can lead to compaction or skin rupture in the membrane process, recent studies suggest several useful applications such as transdermal and osmotic drug delivery systems, miniature bioreactors, etc. However, lack of knowledge about the macrovoid formation mechanism is an obstacle to further development of applications using them. An on-going debate is the role of the surface-tension-driven solutocapillary convection during macrovoid formation. The rapid growth of macrovoids within 1-5 seconds and the high polymer concentration in and near macrovoids make it difficult to explain the mechanism of macrovoid growth by diffusion alone, which is the widely accepted hypothesis proposed by Reuvers et al. The hypothesis advanced by our research group can explain this rapid growth via a mechanism that involves diffusion from the casting solution in the meta-stable region to the macrovoid enhanced by solutocapillary convection induced by the steep nonsolvent concentration gradient in the vicinity of the macrovoid. Since macrovoid growth is hypothesized to be the interplay of a solutocapillary-induced driving force counteracted by viscous drag and buoyancy, eliminate the latter provides a means for testing this hypothesis. Moreover, free convection mass transfer in the nonsolvent immersion bath used to cause phase-separation in membrane casting complicates developing a model for both the wet-casting process and macrovoid growth. The low-g environment minimizes gravitationally induced free convection thereby permitting a tractable solution to the ternary diffusion equations that characterize membrane formation. NASA's Parabolic Flight Research Aircraft provides a small window of low-g (approximately 25 s) that can be used to study macrovoid development in both wet- and dry-cast membranes if an appropriate casting apparatus is used. This casting apparatus should be able to cast the membrane in both low- and high-g in a manner so that essential one-dimensional mass transfer conditions are achieved to insure lateral uniformity in the membrane. The apparatus used in previous research on membrane casting in low-gravity was operated with the plunger driven mechanism. The spring-loaded plunger pushes the bottom block containing the polymer casting solution well directly under the absorbent chamber located in the upper stationary block. However, membranes made via this casting apparatus often displayed lateral nonuniformities that precluded obtaining quantitative information on the macrovoid growth process. Thus, it was necessary to determine the reason for these structural irregularities observed in the low-g casting apparatus. Both experimental as well as computer simulation studies of the low-g casting apparatus established that the impulsive action of the plunger caused the undesired structural nonuniformities. The simulation results showed that the width-to-depth aspect ratio of the shallow well that contains the casting solution in this apparatus was not an important factor in minimizing this problem. Even for a 40:1 (width : depth) aspect ratio, any convection induced by the horizontal motion of the interface of the casting solution will be damped out within 6.25x10(exp 4) seconds. However, the experimental studies revealed that the impulsive motion of the plunger caused a 'sloshing' of the casting solution that had to be eliminated. Therefore, the plungerdriven mechanism was changed to a cam-driven mechanism that did not cause any impulsive motion of the casting solution. Other refinements to this new membrane-casting apparatus include provision for removing the membranes from the casting wells in a less destructive manner. This was accomplished by using a slit geometry for the casting well that permitted disassembly for removal of the cast membrane. The materials used in the construction of this casting apparatus were chosen to insure wetting at the side walls and to maintain precise control of the thickness of the polymer solution in the casting well. An additional provision in this new casting apparatus is the ability to carry out both wet- as well as dry-casting. As such, this apparatus permitted the first studies of the wet-casting of polymeric membranes in low-g. Both wet- and dry-casting experiments on NASA's KC-135 research aircraft employing this new membrane-casting apparatus are scheduled in July 2002. The morphology of the resulting membranes will be characterized using an environmental scanning electron microscope (ESEM). The results of these low-g studies will be reported later.

Lee, Hanyong↗
NASA NTRSDate not supplied

Impacts of Improved Process Representation of Particle Dry Deposition on PM Pollution in a Global Chemistry-Climate Model: Differences Across Regions, Seasons, and PM Sizes

Dry deposition (DD) is a primary removal pathway of particulate matter (PM). The aerosol DD schemes in most global models do not reflect current mechanistic understanding gleaned from observations. The NASA GISS global chemistry-climate model has a new and more dynamic DD scheme that largely captures observed changes in deposition velocities with particle size. We quantify the response of simulated PM to changes in the DD scheme for the Northeast US, Central Europe, North China Plain, and Punjab. Relative to the widely used old scheme, the new scheme shows higher annual PM2.5 for all regions (up to +14%) except C. Europe where there are very small decreases. For PM1, annual increases occur over all regions (up to +20%). For PM10, there are decreases in C. Europe (-8%) and very small decreases in the NE US yet increases (up to +12%) in Punjab and N. China Plain. While there are always increases across seasons for Punjab and N. China Plain, there are both seasonal increases and decreases for the NE US and C. Europe. Given incomplete understanding of observed variations in deposition velocities for a given particle size, we perform sensitivity simulations that perturb the magnitude of the deposition velocities simulated by the new scheme. The annual PM response to increasing DD is similar in magnitude to decreasing DD, implying linearity in the PM sensitivity to DD. The relative annual response to perturbing the DD magnitude is weaker over Punjab and sometimes N. China Plain than the NE US and C. Europe. Higher PM over Punjab and N. China Plain implies a stronger sensitivity to DD when aerosol abundances are low. More mechanistic representation of aerosol DD can sometimes improve or worsen existing model PM biases, which suggests that PM biases due to other processes can be confounded or compounded by biases in DD. Further improvements to DD parameterizations require not only more observational constraints on aerosol deposition velocities but also an advanced understanding of the processes controlling observed variability.

Environmental pollution↗
NASA NTRS1983

Spindt cold cathode electron gun development program

A thin film field emission cathode array and an electron gun based on this emitter array are summarized. Fabricating state of the art cathodes for testing at NASA and NRL, advancing the fabrication technology, developing wedge shaped emitters, and performing emission tests are covered. An anistropic dry etching process (reactive ion beam etching) developed that leads to increasing the packing density of the emitter tips to about 5 x 10 to the 6th power/square cm. Tests with small arrays of emitter tips having about 10 tips has demonstrated current densities of over 100 A/sq cm. Several times using cathodes having a packing density of 1.25 x 10 to the 6th power tips/sq cm. Indications are that the higher packing density achievable with the dry etch process may extend this capability to the 500 A/sq cm range and beyond. The wedge emitter geometry was developed and shown to produce emission. This geometry can (in principle) extend the current density capability of the cathodes beyond the 500 A/sq cm level. An emission microscope was built and tested for use with the cathodes.

Spindt, C. A.↗
DOE OSTI2024

Alternating conduction and convection drying of paper – an experimental analysis with a continuous data acquisition approach

In conventional multi-cylinder drying of paper and board, both conductive drying from steam-heated dryer cylinders and convective drying by flowing air over the paper surface in the pockets are used. Conductive drying from steam-heated drying cylinders is a critical component in providing the necessary thermal energy to paper and board as they dry. Steam temperature and internal and external resistances at the contacting surface are critical process parameters influencing the conductive drying process. An experimental setup was developed to study the alternating conductive and convective drying of paper and board. Paper sheet moisture, temperature, and temperature distribution within the heated platen and the instantaneous heat flux as the sheet was being dried were measured. The instantaneous heat flux, contact heat transfer coefficient, and drying rates were determined as drying proceeds. Experimental results, as well as comparisons to literature and commercial data, are presented. The conductive heat transfer coefficients determined were compared to traditional correlations normally used in the modeling of paper drying. Similarly, the convective heat and mass transfer coefficients are also determined and compared to literature data. In addition to the evaluation of alternating conductive and convective drying characteristics of paper and board, the potential inclusion of auxiliary energy components will also be included. Experimental results from the conduction and convection drying system are presented. Furthermore, this data will be useful in process development, intensification of manufacturing processes, and modeling and simulation of paper drying processes.

42 ENGINEERING↗
DOE OSTI2025

Scale-Up of Novel Li-Conducting Halide Solid State Battery Electrolyte

LBNL and project partner Saint Gobain (SG) demonstrated scalable processing of halide-based solid state batteries. SG’s innovative halide-based SSE utilized in this project is inherently scalable: it can be compressed into a dense electrolyte sheet at room temperature under moderate pressure, can be processed in dry air, and does not present any safety issues during processing or end use. The halide material forms the dense electrolyte layer, and is dispersed in the thick cathode to form a highly conductive path for Li ions. The halide also comes in contact with various environments and other materials (solvents, binders, processing equipment, etc.) throughout the battery manufacturing process, and must be stable in contact with cathode and anode materials during operation.

25 ENERGY STORAGE↗
NASA NTRSDate not supplied

Quantifying the Influence of Mechanistic Representation of Particle Dry Deposition on Historical Changes in Aerosol-Climate Interactions

Dry deposition removes short-lived climate forcers and their precursors from the atmosphere. The aerosol dry deposition schemes in many global climate models have been untouched for decades. Previous work hints that aerosol dry deposition is an uncertainty with respect to aerosol impacts on climate change. Here we demonstrate the impact of a more mechanistic aerosol dry deposition parameterization on the historical aerosol direct and cloud albedo effects using the NASA GISS global chemistry-climate model. We investigate two aerosol configurations – a “bulk” mass-based scheme and a modal scheme that more explicitly represents internal mixing and microphysics – of the global model. Both configurations show ~20% larger historical increases in non-dust aerosols globally with more mechanistic dry deposition. Changes to particle dry deposition, which are strongly a function of particle diameter, have a greater influence on the cloud albedo effect (up to 0.1 W m-2) when aerosols are more explicitly resolved in the modal scheme. On the other hand, impacts on the direct aerosol effect are small for both model configurations. In both aerosol configurations, the global climate effects are relatively insensitive to uncertainty in the strength of the uptake to dry deposition as suggested by (limited) measurements. In general, the low number of aerosol flux measurements and strong variability across existing observations challenge confidence in our understanding of dry depositional processes and changes with environmental conditions. Nonetheless, our work suggests that changes in dry deposition may be important for accurately estimating increases in aerosol abundances over the historical period, which is key for correct inferences about how cooling from aerosols has offset warming from greenhouse gases.

Dry deposition↗
NASA NTRS1989

Cryogenic reactant storage for lunar base regenerative fuel cells

There are major advantages to be gained by integrating a cryogenic reactant storage system with a hydrogen-oxygen regenerative fuel cell (RFC) to provide on-site electrical power during the lunar night. Although applicable to any power system using hydrogen-oxygen RFC's for energy storage, cryogenic reactant storage offers a significant benefit whenever the sun/shade cycle and energy storage period approach hundreds of hours. For solar power installations on the moon, cryogenic reactant storage reduces overall specific mass and meteoroid vulnerability of the system. In addition, it offers synergistic benefits to on-site users, such as availability of primary fuel cell reactants for surface rover vehicles and cryogenic propellants for OTV's. The integration involves processing and storing the RFC reactant streams as cryogenic liquids rather than pressurized gases, so that reactant containment (tankage per unit mass of reactants) can be greatly reduced. Hydrogen-oxygen alkaline RFC's, GaAs photovoltaic (PV) arrays, and space cryogenic processing/refrigeration technologies are assumed to be available for the conceptual system design. Advantages are demonstrated by comparing the characteristics of two power system concepts: a conventional lunar surface PV/RFC power system using pressurized gas storage in SOA filament wound pressure vessels and, that same system with gas liquefaction and storage replacing the pressurized storage. Comparisons are made at 20 and 250 kWe. Although cryogenic storage adds a processing plant (drying and liquefaction) to the system plus 30 percent more solar array to provide processing power, the approximate order of magnitude reduction in tankage mass, confirmed by this analysis, results in a reduction in overall total system mass of approximately 50 percent.

Kohout, Lisa L.↗
NASA NTRS1989

Cryogenic reactant storage for lunar base regenerative fuel cells

There are major advantages to be gained by integrating a cryogenic reactant storage system with a hydrogen-oxygen regenerative fuel cell (RFC) to provide on-site electrical power during the lunar night. Although applicable to any power system using hydrogen-oxygen RFC's for energy storage, cryogenic reactant storage offers a significant benefit whenever the sun/shade cycle and energy storage period approach hundreds of hours. For solar power installations on the moon, cryogenic reactant storage reduces overall specific mass and meteoroid vulnerability of the system. In addition, it offers synergistic benefits to on-site users, such as availability of primary fuel cell reactants for surface rover vehicles and cryogenic propellants for OTV's. The integration involves processing and storing the RFC reactant streams as cryogenic liquids rather than pressurized gases, so that reactant containment (tankage per unit mass of reactants) can be greatly reduced. Hydrogen-oxygen alkaline RFC's, GaAs photovoltaic (PV) arrays, and space cryogenic processing/refrigeration technologies are assumed to be available for the conceptual system design. Advantages are demonstrated by comparing the characteristics of two power system concepts: a conventional lunar surface PV/RFC power system using pressurized gas storage in SOA filament wound pressure vessels and, that same system with gas liquefaction and storage replacing the pressurized storage. Comparisons are made at 20 and 250 kWe. Although cryogenic storage adds a processing plant (drying and liquefaction) to the system plus 30 percent more solar array to provide processing power, the approximate order of magnitude reduction in tankage mass, confirmed by this analysis, results in a reduction in overall total system mass of approximately 50 percent.

Kohout, Lisa L.↗
NASA NTRS1993

Freeze-Drying Makes Improved IPN And Semi-IPN Polymers

Novel process developed for production of interpenetrating polymer networks (IPN's) or semi-IPN's with greater fracture toughness and resistance to microcracks. Process controls degree of phase separation in IPN's. In experiment, IPN's and semi-IPN's formed by dissolving constituents in another common solvent in traditional method. Resins and composite materials produced were tested for both traditional and freeze-drying processes. Glass-transition temperatures and data from dynamic mechanical tests of freeze-dried IPN's and semi-IPN's demonstrated freeze-drying process provided much improved IPN's and semi-IPN's.

Pater, Ruth H.↗
NASA NTRS1991

Powder towpreg process development

The process for dry powder impregnation of carbon fiber tows being developed at LaRC overcomes many of the difficulties associated with melt, solution, and slurry prepregging. In the process, fluidized powder is deposited on spread tow bundles and fused to the fibers by radiant heating. Impregnated tows have been produced for preform, weaving, and composite materials applications. Design and operating data correlations were developed for scale up of the process to commercial operation. Bench scale single tow experiments at tow speeds up to 50 cm/sec have demonstrated that the process can be controlled to produce weavable towpreg. Samples were woven and molded into preform material of good quality.

Baucom, Robert M.↗
NASA NTRS2012

320 x 256 Complementary Barrier Infrared Detector Focal Plane Array for Long-Wave Infrared Imaging

A 320 x 256 Complementary Barrier Infrared (CBIRD) focal plane array for long-wavelength infrared (LWIR) imaging is reported. The arrays were grown by molecular beam expitaxy (MBE) with a 300 period 1.9 um thick absorber. The mean dark current density of 2.2 x 10-4 A/cm2 was measured at an operating bias of 128 mV with a long wavelength cutoff of 8.8 ?m observed at 50% of the peak. The maximum quantum efficiency was 54% measured at 5.6 ?m. Operating at T = 80K, the array yielded an 81% fill factor with 97% operability. Good imagery with a mean noise equivalent different temperature (NE?T) of 18.6 mK and a mean detectivity of D* = 1.3 x 1011 cm-Hz1/2/W was achieved. The substrate was thinned using mechanical lapping and neither an AR coating nor a passivation layer was applied. This article provides the details of the fabrication process for achieving low-dark current LWIR CBIRD arrays. Discussion for an effective hard mask for excellent pattern transfer is given and appropriate mounting techniques for good thermal contact during the dry etching process is described. The challenges and differences between etching large 200 ?m test diodes and small 28 ?m FPA pixels are given.

Focal Plane Arrays (FPA)↗
DOE OSTI2025

Process intensification approach to enhancing heat and mass transfer: Radio frequency (RF) assisted drying of paper and board

Conventional multi-cylinder drying of paper and board typically relies on both conductive drying from steam-heated cylinders and convective drying, where heated air flows over the paper web surface. Conduction primarily contributes to heat transfer, while convection is the main driver of mass transfer. However, conventional drying systems are heavily dependent on steam, usually powered by fossil fuels, and are often energy-inefficient with high levels of waste. Additionally, these surface-driven processes result in a lower percentage of energy absorption compared to the energy supplied, leading to significant energy losses. To improve this long-standing process, an experimental system was developed to investigate a process intensification approach involving the integration of Radio Frequency (RF) heating, a volumetric electromagnetic technology, alongside traditional conduction and convection drying methods. This study also emphasizes the use of sensors to continuously monitor key parameters such as moisture content, supply system temperatures, sample temperatures, air flows, and drying rates in real-time. The effect of RF as an auxiliary energy source in localized environments at varying moisture levels was explored to optimize industrial drying systems, quantify potential improvements, and provide insights for future studies. Experimental results from trials combining RF with convection and with the base case alternating conduction-convection drying processes are presented. It is shown that RF is a viable process intensification approach for paper drying improving the drying rate and energy intensity at higher moisture contents. These findings offer valuable insights for process intensification and contribute to the process development, modeling, and simulation of advanced paper drying techniques.

42 ENGINEERING↗
NASA NTRS1980

Anti-reflection coatings on large area glass sheets

Antireflective coatings which may be suitable for use on the covers of photovoltaic solar modules can be easily produced by a dipping process. The coatings are applied to glass by drawing sheets of glass vertically out of dilute aqueous sodium silicate solutions at a constant speed, allowing the adherent liquid film to dry, then exposing the dried film to concentrated sulfuric acid, followed by a water rinse and dry. The process produces coatings of good optical performance (96.7 percent peak transmission at 0.540 mu M wavelength) combined with excellent stain and soil resistance, and good resistance to abrasion. The process is reproduceable and easily controlled.

Pastirik, E.↗
NASA NTRS2011

Handling Heavenly Jewels - 35 Years of Antarctic Meteorite Processing at Johnson Space Center

The ANSMET program began in 1976, and since that time more than 18,000 meteorites have been processed in the Meteorite Processing Lab at Johnson Space Center in Houston, TX[1]. The meteorites are collected and returned to JSC on a freezer truck and remain frozen until they are initially processed. Initial Processing of Meteorites: Initial processing involves drying the meteorites in a nitrogen glove box for 24 to 48 hours, photographing, measuring, weighing and writing a description of the interior and exterior. The meteorite is broken and a representative sample is sent to the Smithsonian Institution for classification. Newsletter & Requests: Once initial processing has been complete and the meteorites have been classified, the information is published in the Antarctic Meteorite Newsletter[2,3]. The newsletter is published twice yearly and is sent electronically to researchers around the world and is also available on line. Researchers are asked to fill out a request form and submit it to the Meteorite Working Group secretary. All sample requests will be reviewed by either the meteorite curator or the Meteorite Working Group de-pending on the type of meteorite and the research being conducted. Processing for Sample Requests: In the meteorite processing lab, meteorite samples are prepared several different ways. Most samples are prepared as chips obtained by use of stainless steel chisels in a chipping bowl or rock splitter. In special situations where a researcher needs a slab the meteorite samples can be bandsawed in a dry nitrogen glove box with a diamond blade, no liquids are ever introduced into the cabinet. The last type of sample preparation is thin/thick sections. The meteorite thin section lab at JSC can prepare standard 30-micron thin sections, thick sections of variable thickness (100 to 200 microns), or demountable sections using superglue. Information for researchers: It is important that re-searchers fill the sample request form completely, in order to make sure the meteorite is processed correctly[4]. Re-searchers should list any special requirements on the form, i.e. packaging of samples (poly vs. stainless), thick sections and thickness needed, superglue needed, interior chips, exterior chips, fusion crust, contamination issues, all concerns should be listed so processing can be done accurately and any concerns the researcher has can be addressed be-fore the meteorites are broken.

Satterwhite, C. E.↗