Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “disulfides”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Atmospheric measurements of carbonyl sulfide, dimethyl sulfide, and carbon disulfide using the electron capture sulfur detector

Measurements of atmospheric dimethyl sulfide (DMS), carbonyl sulfide (COS), and carbon disulfide (CS2) were conducted over the Atlantic Ocean on board the NASA Electra aircraft during the Chemical Instrumentation Test and Evaluation (CITE 3) project using the electron capture sulfur detector (ECD-S). The system employed cryogenic preconcentration of air samples, gas chromatographic separation, catalytic fluorination, and electron capture detection. Samples collected for DMS analysis were scrubbed of oxidants with NaOH impregnated glass fiber filters to preconcentration. The detection limits (DL) of the system for COS, DMS, and CS2 were 5, 5, and 2 ppt, respectively. COS concentrations ranged from 404 to 603 ppt with a mean of 489 ppt for measurements over the North Atlantic Ocean (31 deg N to 41 deg N), and from 395 to 437 ppt with a mean of 419 ppt for measurements over the Tropical Atlantic Ocean (11 deg S to 2 deg N). DMS concentrations in the lower marine boundary layer, below 600-m altitude, ranged from below DL to 150 ppt from flights over the North Atlantic, and from 9 to 104 ppt over the Tropical Atlantic. CS2 concentrations ranged from below DL to 29 ppt over the North Atlantic. Almost all CS2 measurements over the Tropical Atlantic were below DL.

Johnson, James E.↗
NASA NTRS2002

Comparison of Several Different Sputtered Molybdenum Disulfide Coatings for Use in Space Applications

Tribology experiments on different types of sputtered molybdenum disulfide (MoS2) coatings (obtained from different vendors) using accelerated testing techniques were conducted. The purpose was to determine which would be the best coating for use with auxiliary journal bearings for spacecraft energy storage flywheels. Experiments were conducted in moist air (50% relative humidity) and in dry air (<100 PPM water vapor content) on a Pin-on-Disk Tribometer to determine how well the coatings would perform in air. Experiments were also conducted on a Block-on-Ring Tribometer in dry nitrogen (<100 PPM water vapor) to simulate how well the coatings would perform in vacuum. Friction, counterface wear, coating wear, endurance life and surface morphology were investigated.

Fusaro, Robert L.↗
NASA NTRS2009

On the Formation of Cometary Carbon Disulfide (CS2)

The formation of cometary CS molecules from carbon disulfide, CS2 , was proposed about 20 years before the latter's detection in comet 122P/de Vico by Jackson et al. (2002). However, the origin of CS2 has received little attention from either experimentalists or theorists. As part of our on-going laboratory program to investigate cometary molecules we have examined chemical reactions that lead to CS2 in the solid state. Icy mixtures of known cometary molecules were proton irradiated near 10 K to doses of several eV per molecule. Mid-IR spectroscopy was used as an in situ probe to record both CS2 formation in the ices and the destruction of precursors. We find that the most likely route to cometary CS2 is through OCS by way of the S + CO reaction.

Hudson, Reggie↗
NASA NTRS2011

Negative Ion Drift Velocity and Longitudinal Diffusion in Mixtures of Carbon Disulfide and Methane

Negative ion drift velocity and longitudinal diffusion has been measured for gas mixtures of carbon disulfide (CS2) and methane (CH4)' Measurements were made as a function of total pressure, CS2 partial pressure and electric field. Constant mobility and thermal-limit longitudinal diffusion is observed for all gas mixtures tested. Gas gain for some of the mixtures is also included.

Dion, Michael P.↗
DOE OSTI2023

Investigation of the structure, filler interaction and degradation of disulfide elastomers made by Reversible Radical Recombination Polymerization (R3P)

In this paper we report the synthesis and analysis of cyclic polydisulfides, their redox depolymerization as well as their interaction with carbon black. Cyclic poly(3,6-dioxa-1,8-octanedithiol)s (pDODT) were synthesized by Reversible Radical Recombination Polymerization (R3P). R3P is a scalable “green” polymerization process using triethylamine (TEA), H 2 O 2 and air for the polymerization of dithiol monomers. pDODTs were synthesized in 5 and 20 g batches. The effect of peroxide concentration (3, 5, 10, 20, 30%) was investigated. It was found that the molecular weights increased exponentially with increasing peroxide concentrations. At 30% peroxide concentration pDODTs with M n up to 400,000 g/mol and polydispersity of 2 were obtained. 700 and 800 MHz NMR were used for investigating the chemical structure of the polymers. The absence of thiol end group signals in polymers made with > 10wt % H 2 O 2 and M n < 100,000 g/mol, including a sample of a fractionated polymer with starting Mn = 600,000 g/mol, verified cyclic structures. Dithiothreitol reduced the polymers to monomer and a small percentage of oligomers. Carbon black was shown to increase the moduli of high molecular weight pDODTs. Swelling tests in chloroform showed that polymers made with 20 and 30w% peroxide swelled 14 and 10 times of their starting weight without dissolving, indicating chemical interaction between the polymers and carbon black. In conclusion, further analysis of these interesting elastomers, available at the 20 g scale, is in progress.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Spontaneous Polarization Suppression of Exciton–Exciton Annihilation in Rhombohedral-Stacked Bilayer Molybdenum Disulfide

Rapid exciton–exciton annihilation (EEA) in two-dimensional semiconductors limits access to high-density excitonic regimes essential for efficient optoelectronic operation under strong excitation. Here, we show that EEA is strongly suppressed in rhombohedral (3R)-stacked MoS 2 bilayers relative to nonpolar 2H bilayers, and that this suppression is quantitatively consistent with repulsive dipole–dipole interactions between layer-polarized excitons induced by spontaneous polarization. Using ultrafast pump–probe spectroscopy, we measure an EEA rate of γ EEA = (5.03 ± 0.99) × 10 –3 cm 2 s –1 in 3R bilayers, which is approximately 18.2-fold smaller than that in monolayers and 2.9-fold smaller than that in nonpolar 2H bilayers. Despite the higher exciton diffusivity recently reported for 3R relative to 2H bilayers, the reduced EEA rate in 3R indicates a rate-limited regime governed by the close-encounter annihilation probability rather than diffusion. A rate-limited annihilation model incorporating a dipole–dipole repulsive potential captures the observed ratio γ EEA,3R /γ EEA,2H ≈ 0.35 for an exciton–exciton encounter distance of ∼1.3 nm, consistent with the bilayer exciton Bohr radius. These results indicate that spontaneous polarization in 3R-stacked bilayers can suppress nonlinear excitonic losses and provide a route toward high-density excitonics.

dipolar excitons↗
DOE OSTI2023

Molybdenum Disulfide Nanoribbons with Enhanced Edge Nonlinear Response and Photoresponsivity

MoS 2 nanoribbons have attracted increased interest due to their properties, which can be tailored by tuning their dimensions. Herein, the growth of MoS 2 nanoribbons and triangular crystals formed by the reaction between films of MoOx (2 2 nanoribbons arising from distinct contributions from the single–layer edges and multilayer core. Nanoscale imaging reveals a blue-shifted exciton emission of the monolayer edge compared to the isolated MoS 2 monolayers due to built-in local strain and disorder. We further report on an ultrasensitive photodetector made of a single MoS 2 nanoribbon with a responsivity of 8.72 × 10 2 A W –1 at 532 nm, among the highest reported up-to-date for single-nanoribbon photodetectors. These findings can inspire the design of MoS 2 semiconductors with tunable geometries for efficient optoelectronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Layered Nano-Mosaic of Niobium Disulfide Heterostructures by Direct Sulfidation of Niobium Carbide MXenes for Hydrogen Evolution

MXene-transition metal dichalcogenide (TMD) heterostructures are synthesized through a one-step heat treatment of Nb 2 C and Nb 4 C 3 . These MXenes are used without delamination or any pre-treatment. Heat treatments accomplish the sacrificial transformation of these MXenes into TMD (NbS 2 ) at 700 and 900 °C under H 2 S. This work investigates, for the first time, the role of starting MXene phase in the derivative morphology. It is shown that while treatment of Nb 2 C at 700 °C leads to the formation of pillar-like structures on the parent MXene, Nb 4 C 3 produces nano-mosaic layered NbS 2 . At 900 °C, both MXene phases, of the same transition metal, fully convert into nanomosaic layered NbS 2 preserving the parent MXene’s layered morphology. When tested as electrodes for hydrogen evolution reaction, Nb 4 C 3 -derived hybrids show better performance than Nb 2 C derivatives. The Nb 4 C 3 -derived heterostructure exhibits a low overpotential of 198 mV at 10 mA cm -2 and a Tafel slope of 122 mV dec -1 , with good cycling stability in an acidic electrolyte

36 MATERIALS SCIENCE↗
DOE OSTI2023

Solution synthesis of two-dimensional zinc oxide (ZnO)/molybdenum disulfide (MoS 2 ) heterostructure through reactive templating for enhanced visible-light degradation of rhodamine B

Numerous inorganic materials have been identified as potential candidates for high-performance photocatalysts. However, their solar-to-energy conversion efficiencies still fail to meet commercial requirements. Here, the main hurdle is the rapid recombination of photoexcited electrons and holes in single-phase materials. A viable predicted approach to suppress charge recombination is coupling two materials to form a two-dimensional (2D) heterostructure that physically separates photoinduced electrons and holes in different layers. In this work, the heterostructure-based paradigm was tested and a scalable solution synthesis of epitaxial ZnO-MoS 2 heterostructure was developed. A 2D ZnO-MoS 2 heterostructure was synthesized under hydrothermal conditions by stabilizing intermediate Zn-hydroxide states on a functionalized MoS 2 surface. Detailed characterization showed the formation of multilayer heterostructure with MoS 2 flakes intercalated between large size ZnO plates. The performance of this heterostructure was evaluated using photocatalytic degradation of rhodamine B. A degradation efficiency of 70% was measured within 90 minutes of visible-light irradiation, almost doubling the efficiency of the corresponding single-phase materials or their physical mixtures.

2D heterostructure↗