Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “diamond”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

Diamond Heat-Spreader for Submillimeter-Wave Frequency Multipliers

The planar GaAs Shottky diode frequency multiplier is a critical technology for the local oscillator (LO) for submillimeter- wave heterodyne receivers due to low mass, tenability, long lifetime, and room-temperature operation. The use of a W-band (75-100 GHz) power amplifier followed by a frequency multiplier is the most common for submillimeter-wave sources. Its greatest challenge is to provide enough input power to the LO for instruments onboard future planetary missions. Recently, JPL produced 800 mW at 92.5 GHz by combining four MMICs in parallel in a balanced configuration. As more power at W-band is available to the multipliers, their power-handling capability be comes more important. High operating temperatures can lead to degradation of conversion efficiency or catastrophic failure. The goal of this innovation is to reduce the thermal resistance by attaching diamond film as a heat-spreader on the backside of multipliers to improve their power-handling capability. Polycrystalline diamond is deposited by hot-filament chemical vapor deposition (CVD). This diamond film acts as a heat-spreader to both the existing 250- and 300-GHz triplers, and has a high thermal conductivity (1,000-1,200 W/mK). It is approximately 2.5 times greater than copper (401 W/mK) and 20 times greater than GaAs (46 W/mK). It is an electrical insulator (resistivity approx. equals 10(exp 15) Ohms-cm), and has a low relative dielectric constant of 5.7. Diamond heat-spreaders reduce by at least 200 C at 250 mW of input power, compared to the tripler without diamond, according to thermal simulation. This superior thermal management provides a 100-percent increase in power-handling capability. For example, with this innovation, 40-mW output power has been achieved from a 250-GHz tripler at 350-mW input power, while the previous triplers, without diamond, suffered catastrophic failures. This breakthrough provides a stepping-stone for frequency multipliers-based LO up to 3 THz. The future work for this design is to apply the high output power from both the 250 and 300 GHz to multiple chains in order to generate milliwatts at 2.3 THz. Using the first generation of results for this innovation, 40 mW of output power were produced from a 240-GHz tripler at 350-mW input power, and 27- mW output power was produced from a 300-GHz tripler at 408-mW input power. This is two times higher than the current state-of-the-art output power capability. A finite-element thermal simulation also shows that 30-microns thick diamond dropped the temperature of the anodes by at least 200 C.

Lin, Robert H.↗
NASA NTRS2014

Diamond Synthesis Employing Nanoparticle Seeds

Iron nanoparticles were employed to induce the synthesis of diamond on molybdenum, silicon, and quartz substrates. Diamond films were grown using conventional conditions for diamond synthesis by hot filament chemical vapor deposition, except that dispersed iron oxide nanoparticles replaced the seeding. This approach to diamond induction can be combined with dip pen nanolithography for the selective deposition of diamond and diamond patterning while avoiding surface damage associated to diamond-seeding methods.

Uppireddi, Kishore↗
DOE OSTI2020

Diamond nanostructures with large surface area and method of producing the same

A method for forming diamond nanostructures with large specific area can include forming porous diamond nanostructures by means of selectively etching sp2-bonded carbon and partially removing sp3-bonded carbon in nanocrystalline diamond (NCD) and ultrananocrystalline diamond (UNCD® diamond). The diamond nanostructures achieved from the disclosed method can include a long shaft surrounded by a school of barbs. The nanostructure can provide a significantly larger surface area than diamond without such a nanostructure and its fabrication provides relative ease of manufacture compared to traditional techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Scanning X-Ray Diffraction Microscopy for Diamond Quantum Sensing

An understanding of nano- and microscale crystal strain in chemical-vapor-deposition diamond is crucial to the advancement of diamond quantum technologies. In particular, the presence of such strain and its characterization presents a challenge to diamond-based quantum sensing and information applications-as well as for future dark-matter detectors, where the directional information about incoming particles is encoded in crystal strain. Here, we exploit nanofocused scanning x-ray diffraction microscopy to quantitatively measure crystal deformation from defects in diamond with high spatial and strain resolution. The combination of information from multiple Bragg angles allows stereoscopic three-dimensional modeling of strain-feature geometry; the diffraction results are validated via comparison to optical measurements of the strain tensor based on spin-state-dependent spectroscopy of ensembles of nitrogen-vacancy centers in the diamond. Finally, our results demonstrate both strain and spatial resolution sufficient for directional detection of dark matter via x-ray measurement of crystal strain and provide a promising tool for diamond growth analysis and improvement of defect-based sensing.

42 ENGINEERING↗
DOE OSTI2026

Sub-melt nanosecond pulsed-laser induced densification and strain-field relaxation in single-crystal diamond

Dislocations and polishing-induced defect networks in synthetic diamond introduce local strain fields and broaden Raman features, limiting performance in optical, thermal, and electronic applications. Laser annealing is emerging as a promising approach to repair surface and near-surface defects in diamond without entering the melt regime, yet surface densification, defect-state modification, and associated structural changes have not been well quantified. In this work, we show that sub-melt nanosecond pulsed-laser annealing (PLA) induces near-surface densification and defect-mediated strain relaxation in single-crystal Chemical Vapor Deposition (CVD) diamond. Single- and two-pulse PLA were applied, and structural evolution was quantified using co-registered ISO 25,178 white-light interferometry, depth-resolved Raman spectroscopy, and cross-sectional STEM with geometric phase analysis (GPA). Across a 5 × 6 grid (n = 30), responsive regions exhibit large reductions in local slope (Sdq 45–65%), developed area (Sdr 60–90%), height spread (Sp, Sz 30–65%), void volume (Vv 57–60%), and roughness amplitude (Sa, Sq 48–57%), consistent with densification of ∼4–6.5 nm. Raman profiling shows narrowing of the diamond line and improved spectral uniformity to depths of ∼2–3 μm. Given that the Raman probing depth significantly exceeds the densified layer thickness, this response is interpreted as consistent with long-range strain-field redistribution originating from the near-surface region. STEM-GPA strain maps further support this interpretation, showing smoother strain fields, suppressed hotspots, and redistribution of localized strain concentrations following PLA. These results are consistent with defect-mediated strain relaxation and densification-driven modification of the near-surface energy state. The approach provides a scalable pathway for improving near-surface structural quality in diamond relevant to electronic, photonic, and quantum applications.

Areal surface metrology (ISO 25,178)↗
DOE OSTI2023

Diamond rotors

The resolution of magic angle spinning (MAS) nuclear magnetic resonance (NMR) spectra remains bounded by the spinning frequency, which is limited by the material strength of MAS rotors. Since diamond is capable of withstanding 1.5–2.5x greater MAS frequencies, compared to state-of-the art zirconia, we fabricated rotors from single crystal diamond. When combined with bearings optimized for spinning with helium gas, diamond rotors could achieve the highest MAS frequencies to date. Furthermore, the excellent microwave transmission properties and thermal conductivity of diamond could improve sensitivity enhancements in dynamic nuclear polarization (DNP) experiments. The fabrication protocol we report involves novel laser micromachining and produced rotors that presently spin at ω r = 111.000 ± 0.004 kHz, with stable spinning up to 124 kHz, using N 2 gas as the driving fluid. Here, we present the first proton-detected 13 C/ 15 N MAS spectra recorded using diamond rotors, a critical step towards studying currently inaccessible ex-vivo protein samples with MAS NMR. Previously, the high aspect ratio of MAS rotors (~10:1) precluded fabrication of MAS rotors from diamond.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

High- Q Nanophotonic Resonators on Diamond Membranes using Templated Atomic Layer Deposition of TiO 2

Integrating solid-state quantum emitters with nanophotonic resonators is essential for efficient spin-photon interfacing and optical networking applications. While diamond color centers have proven to be excellent candidates for emerging quantum technologies, their integration with optical resonators remains challenging. Conventional approaches based on etching resonators into diamond often negatively impact color center performance and offer low device yield. In this work, we developed an integrated photonics platform based on templated atomic layer deposition of TiO 2 on diamond membranes. Our fabrication method yields high-performance nanophotonic devices while avoiding etching wavelength-scale features into diamond. Moreover, this technique generates highly reproducible optical resonances and can be iterated on individual diamond samples, a unique processing advantage. Our approach is suitable for a broad range of both wavelengths and substrates and can enable high-cooperativity interfacing between cavity photons and coherent defects in diamond or silicon carbide, rare earth ions, or other material systems.

42 ENGINEERING↗
DOE OSTI2025

Inelastic deformation of diamond single crystals shock compressed to multimegabar stresses: Wave profile calculations

As the archetypal strong solid, the response of diamond shock compressed to multimegabar stresses is important for fundamental science and for numerical simulations of wave profiles for applications in high energy density physics experiments. Previous experiments and analysis have shown that the commonly used hydrodynamic assumption is invalid for diamond shock compressed to stresses below melt and an elastic–inelastic description is needed. Here, we present a phenomenological material model for calculating wave profiles in shock compressed diamond single crystals that incorporates this description. Also, to support the modeling effort, we carried out wave profile measurements on shock compressed diamond single crystals at the Sandia Z facility to augment previous measurements. Wave profiles for [100] and [111] diamond calculated using the material model provide a good match to the elastic–inelastic response (observed two-wave structure) measured at ∼325 and ∼360 GPa. Furthermore, the calculated peak stresses for single (overdriven) waves provide a good match to the measured Hugoniot states for stresses reaching ∼700 GPa, which is near melting conditions. The present results show that the diamond single crystal response at multimegabar shock stresses is characteristic of a brittle solid—pressure-dependent strength and strength loss due to inelastic deformation.

Deformation↗
DOE OSTI2022

Tungsten doped diamond shells for record neutron yield inertial confinement fusion experiments at the National Ignition Facility

We report on fabrication and characterization of layered, tungsten doped, spherical about 2 mm diameter microcrystalline diamond ablator shells for inertial confinement fusion (ICF) experiments at the National Ignition Facility. As previously reported, diamond ICF ablator shells can be fabricated by chemical vapor deposition (CVD) on solid spherical silicon mandrels using an ellipsoidal microwave plasma reactor. In the present work, we further developed these ablator shells by embedding a W -doped diamond layer sandwiched between two undoped diamond regions. W incorporation in diamond was achieved by adding tungsten hexacarbonyl to the CH 4 /H 2 CVD feed gas. We observe that the W doping concentration decreases with increasing deposition rate which, in turn, is controlled by adjusting the total gas pressure. Cross sectional microstructural analysis reveals sharp interfaces between doped and undoped regions of the diamond shell and uniform W distribution with concentrations up to about 0.3 at.%. At higher W concentrations (>0.3 at.%) formation of tungsten carbide precipitates is observed. Using a 3-shock 1.6 MJ laser pulse, the targets described in this work produced the first laser driven implosion to break the 1 × 10 16 neutron yield barrier, followed by experiments (described in future publications) with similar targets and slightly more laser energy producing yields as high as 4 × 10 17 .

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Scintillation light detection in polycrystalline diamond using single photon detectors

Here, this study investigates the scintillation properties of polycrystalline diamond for particle detection applications, particularly in neutron and alpha radiation environments. Polycrystalline diamonds provide a cost-effective alternative to monocrystalline diamonds while retaining essential detection properties. Photoluminescence measurements were performed to analyze emission spectra, revealing distinct characteristics based on impurity content and crystallinity. Scintillation responses were assessed using Silicon Photomultipliers (SiPMs), demonstrating the capability of polycrystalline diamond powders to respond to alpha irradiation, albeit with reduced resolution compared to traditional scintillators. A prototype neutron detector was developed by combining diamond powder with neutron-sensitive 6 LiF, and its performance was evaluated through experimental testing and Geant4 simulations. The findings indicate that polycrystalline diamond-based detectors can achieve significant detection efficiency while remaining insensitive to gamma radiation, offering potential for portable neutron detection applications.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Diamond magnetometer enhanced by ferrite flux concentrators

Magnetometers based on nitrogen-vacancy (NV) centers in diamond are promising room-temperature, solid-state sensors. However, their reported sensitivity to magnetic fields at low frequencies (≲1 kHz) is presently ≳10 pTs 1/2 , precluding potential applications in medical imaging, geoscience, and navigation. Here we show that high-permeability magnetic flux concentrators, which collect magnetic flux from a larger area and concentrate it into the diamond sensor, can be used to improve the sensitivity of diamond magnetometers. By inserting an NV-doped diamond membrane between two ferrite cones in a bowtie configuration, we realize a ~ 250-fold increase of the magnetic field amplitude within the diamond. We demonstrate a sensitivity of ~ 0.9pTs 1/2 to magnetic fields in the frequency range between 10 and 1000 Hz. This is accomplished using a dual-resonance modulation technique to suppress the effect of thermal shifts of the NV spin levels. The magnetometer uses 200 mW of laser power and 20 mW of microwave power. This work introduces a new degree of freedom for the design of diamond sensors by using structured magnetic materials to manipulate magnetic fields.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Electrical and Thermal Performance of Ga₂O₃–Al₂O₃–Diamond Super-Junction Schottky Barrier Diodes

The design space of Ga 2 O 3 -based devices is severely constrained due to its low thermal conductivity and absence of viable p-type dopants. In this work, we discuss the limits of operation of a novel Ga 2 O 3 –Al 2 O 3 –diamond-based super-junction device concept, which can alleviate the constraints associated with Ga 2 O 3 -based devices. The improvements achieved using the proposed device concept are demonstrated through electrical and thermal simulations of Ga 2 O 3 –Al 2 O 3 –diamond-based super-junction Schottky barrier diodes (SJ-SBDs) and non-punch-through or conventional Schottky barrier diodes (NP-SBDs). The SJ-SBD enables operation below the R ON -breakdown voltage limit of Ga 2 O 3 NP-SBD, enabling >4 kV blocking voltage at R ON of 1–3 mΩ cm 2 . Here, the maximum switching frequency of SJ-SBD may be only a few kHz, as it is limited by the activation energy of acceptors (0.39 eV) in the diamond. Crucially, compared with NP-SBD, the use of diamond also results in ~60% reduction in temperature rise during static power dissipation. Polycrystalline diamond (PCD) properties depend on detailed microstructure and benefits compared to ideal Ga 2 O 3</sub NP-SBD arise for diamond critical fields ≥6 MV/cm and thermal conductivities as low as 50–150 W/(m • K).

36 MATERIALS SCIENCE↗
DOE OSTI2020

Photonic devices fabricated from (111)‐oriented single crystal diamond

Abstract Diamond is a material of choice in the pursuit of integrated quantum photonic technologies. So far, the majority of photonic devices fabricated from diamond are made from (100)‐oriented crystals. In this work, we demonstrate a methodology for the fabrication of optically active membranes from (111)‐oriented diamond. We use a liftoff technique to generate membranes, followed by chemical vapor deposition of diamond in the presence of silicon to generate homogenous silicon vacancy color centers with emission properties that are superior to those in (100)‐oriented diamond. We further use the diamond membranes to fabricate microring resonators with quality factors exceeding ~ 3000. Supported by finite‐difference time‐domain calculations, we discuss the advantages of (111)‐oriented structures as building blocks for quantum nanophotonic devices. image

Regan, Blake↗
DOE OSTI2020

A Revisited Mechanism of the Graphite-to-Diamond Transition at High Temperature

The graphite-diamond transition, under high-pressure and high-temperature conditions, has been a central subject in physical science. However, its atomistic mechanism remains under debate. Employing large-scale molecular dynamics (MD) simulations, we report a mechanism whereby the diamond nuclei in the graphite matrix propagate in two preferred directions, among which the graphite [120] is about 2.5 times faster than [001]. Consequently, cubic diamond (CD) is the kinetically favorable product, while only a few hexagonal diamonds (HDs) can exist as the twins of CDs. The coherent interface of t-(100)gr//(11-1)cd + [010]gr//[1-10]cd observed in MD simulation was confirmed by our high-resolution transmission electron microscopy experiment. This proposed mechanism not only clarifies the role of HD in graphite-diamond transition but also yields atomistic insight into strengthening synthetic diamond via microstructure engineering.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Electronic Spin Relaxation and Clustering in High-Pressure High-Temperature Synthesized Microcrystalline Diamond Particles with Reduced Nitrogen Content

The negatively charged nitrogen-vacancy (NV – ) color center in diamonds is widely studied because of numerous applications of this unique quantum system in sensing and quantum information sciences. While substitutional nitrogen is required to form the NV – centers in diamond, it also yields other paramagnetic defects─primarily the neutrally charged substitutional nitrogen centers (P1)─that decrease NV – spin coherence, which in turn degrades performance in applications. Herein, we investigate high-pressure high-temperature synthesized diamond microparticles (ca. 140–185 μm) having lower─ranging from 3 to 38 ppm─than the typical nitrogen content of type 1b diamond ( ca. 100 ppm and higher) typically used for the production of fluorescent diamond particles with NV – centers. A suite of electron paramagnetic resonance, optically detected magnetic resonance, and nuclear magnetic resonance methods are used to characterize spin properties of P1 and NV – centers in the particles. Upon decreasing the nitrogen content from 29 to 3 ppm, the ensemble NV – T 2 relaxation time increased by about 3-fold as measured directly in the Hahn Echo experiment at magnetic field of 1.2 T. Analysis of electronic relaxation of P1 centers revealed the existence of at least two distinct populations of P1 centers, consisting of fast and slower relaxing spins and allowed for an estimation of local concentrations. Even with <10 ppm nitrogen contents, the analysis indicated a highly heterogeneous distribution of P1 centers, suggesting the possibility of P1 spin clustering even at low nitrogen concentrations. The combined data demonstrate that the particles prepared from HPHT diamond with a low nitrogen content offer improved spin properties that are beneficial for NV – sensing applications.

Carbon↗
DOE OSTI2024

Improving the creation of SiV centers in diamond via sub-μs pulsed annealing treatment

Silicon-vacancy (SiV) centers in diamond are emerging as promising quantum emitters in applications such as quantum communication and quantum information processing. Here, we demonstrate a sub-μs pulsed annealing treatment that dramatically increases the photoluminescence of SiV centers in diamond. Using a silane-functionalized adamantane precursor and a laser- heated diamond anvil cell, the temperature and energy conditions required to form SiV centers in diamond were mapped out via an optical thermometry system with an accuracy of ±50 K and a 1 μs temporal resolution. Annealing scheme studies reveal that pulsed annealing can obviously minimize the migration of SiV centers out of the diamond lattice, and a 2.5-fold increase in the number of emitting centers was achieved using a series of 200-ns pulses at a 50 kHz repetition rate via acousto-optic modulation. Our study provides a novel pulsed annealing treatment approach to improve the efficiency of the creation of SiV centers in diamond.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Metastability and Ostwald step rule in the crystallisation of diamond and graphite from molten carbon

Abstract Experimental challenges in determining the phase diagram of carbon at temperatures and pressures near the graphite-diamond-liquid triple point are often related to the persistence of metastable crystalline or glassy phases, superheated crystals, or supercooled liquids. A deeper understanding of the crystallisation kinetics of diamond and graphite is crucial for effectively interpreting the outcomes of these experiments. Here, we reveal the microscopic mechanisms of diamond and graphite nucleation from liquid carbon through molecular simulations with first-principles machine learning potentials. Our simulations accurately reproduce the experimental phase diagram of carbon near the triple point and show that liquid carbon crystallises spontaneously upon cooling. Metastable graphite crystallises in the domain of diamond thermodynamic stability at pressures above the triple point. Furthermore, whereas diamond crystallises through a classical nucleation pathway, graphite follows a two-step process in which low-density fluctuations forego ordering. Calculations of the nucleation rates of the two competing phases confirm this result and reveal a manifestation of Ostwald’s step rule, where the strong metastability of graphite hinders the transformation to the stable diamond phase. Our results provide a key to interpreting melting and recrystallisation experiments and shed light on nucleation kinetics in polymorphic materials with deep metastable states.

Science & Technology - Other Topics↗
DOE OSTI2023

Probing itinerant carrier dynamics at the diamond surface using single nitrogen vacancy centers

Color centers in diamond are widely explored for applications in quantum sensing, computing, and networking. Their optical, spin, and charge properties have extensively been studied, while their interactions with itinerant carriers are relatively unexplored. Here, we show that NV centers situated 10 ± 5 nm of the diamond surface can be converted to the neutral charge state via hole capture. By measuring the hole capture rate, we extract the capture cross section, which is suppressed by proximity to the diamond surface. The distance dependence is consistent with a carrier diffusion model, indicating that the itinerant carrier lifetime can be long, even at the diamond surface. Measuring dynamics of near-surface NV centers offers a tool for characterizing the diamond surface and investigating charge transport in diamond devices.

Physics↗