Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “densification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Microstructure of irradiated AGR TRISO particle buffer layers as measured by X-ray computed tomography

Shrinkage of the initially low-density buffer layer in tristructural isotropic (TRISO) coated fuel particles during irradiation is a well-known phenomenon with potential implications for fission product and actinide transport, as well as potential pyrocarbon fracture that in some cases has been observed to impact particle performance. During post-irradiation examination, the buffer layer's structure is commonly determined using 2D microscopy of a particle cross section or a series of particle cross sections at staggered depths. Although these methods provide a general idea of the irradiated buffer microstructure, they do not provide a full picture of the TRISO coating microstructure. By contrast, x-ray computed tomography (XCT) provides full 3D imaging of the TRISO particle. Particles from various compacts irradiated for the Advanced Gas Reactor Fuel Development and Qualification Program were imaged using XCT. Some of these particles were selected because of abnormal fission product inventories (e.g., low 137 Cs), whereas others were randomly selected from the center of the fission product inventory distribution. Qualitative and quantitative analysis techniques were applied to the randomly selected particles as representatives of typical TRISO behavior to study the post-irradiation structure of the buffer layer. These results showed that, while separation of the buffer and inner pyrolytic carbon layers was a common behavior during the radiation-induced shrinkage of the buffer, a portion of the original buffer/inner pyrolytic carbon interface remained intact throughout irradiation in nearly all cases. Furthermore, these results also indicated clear trends in the degree of buffer densification with irradiation temperature and fluence.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Are the U.S. Biorefineries Over the Hurdle of 2000 Ton Daily Throughput Yet?

The efficient utilization of lignocellulosic biomass for biofuel and biochemical production is hindered by material handling issues such as clogging and segregation among other challenges. Preprocessing methods such as drying, screening, and milling have improved conversion yield but have not sufficiently enhanced flowability, especially herbaceous biomass. The poor flowability of herbaceous biomass is rooted in some particle attributes that remain less altered by those methods, e.g., irregular particle shape, high roughness, and high compressibility, making it hard to scale up throughput to a key benchmark for a biorefinery – 2000 ton per day. Applying additional preprocessing methods like pelletization and torrefaction to drastically change those particle attributes can improve flow and handling but has not been comprehensively verified through test. The flowability of herbaceous biomass feedstock formats generated by three different preprocessing methods was recently assessed at Idaho National Laboratory’s Biomass Feedstock National User Facility: first, loose particles size reduced from as-received materials; second, pellets produced from an efficient densification process; and third, powders milled from torrefied pellets. Benchmarking tests including static angle of repose, basic flow energy measured in a powder rheometer, and discharge flow in an adjustable hopper, were conducted to evaluate those feedstock formats. Beyond the capacity of existing experimental apparatuses, a digital engineering approach involving flow simulations and AI models were used to identity the material attributes and processing parameters that have dominant influences on flow throughput. Techno-economic analysis focusing on hopper flow as a typical material handling operation was conducted for those feedstock formats. Perspectives will be discussed on whether the 2000-ton daily throughput for a biorefinery is achievable at an acceptable cost by using any of the tested preprocessing methods.

09 - BIOMASS FUELS↗
DOE OSTI2020

Ultra‐Uniform Nanocrystalline Materials via Two‐Step Sintering

Abstract Nanocrystalline materials with superior properties are of great interest. Much is discussed about obtaining nanograins, but little is known about maintaining grain‐size uniformity that is critical for reliability. An especially intriguing question is whether it is possible to achieve a size distribution narrower than what Hillert theoretically predicted for normal grain growth, a possibility suggested—for growth with a higher growth exponent—by the generalized mean‐field theory of Lifshitz, Slyozov, Wagner (LSW), and Hillert but never realized in practice. Following a rationally designed two‐step sintering route, it has been made possible in bulk materials by taking advantage of the large growth exponent in the intermediate sintering stage to form a uniform microstructure despite residual porosity, and freezing the grain growth thereafter while continuing densification to reach full density. The bulk dense Al 2 O 3 ceramic thus obtained has an average grain size of 34 nm and a size distribution much narrower than Hillert's prediction. Bulk Al 2 O 3 with a grain‐size distribution narrower than the particle‐size distribution of starting powders is also demonstrated, as are highly uniform bulk engineering metals (refractory Mo and W‐Re alloy) and complex functional ceramics (BaTiO 3 ‐based alloys with superior dielectric strength and energy capacity).

Dong, Yanhao↗
DOE OSTI2020

In Situ Construction of Uniform and Robust Cathode–Electrolyte Interphase for Li-Rich Layered Oxides

The high-energy-density Li-rich layered oxides (LLOs) as promising cathodes for Li-ion batteries suffer from the dissolution of transition metals (especially manganese) and severe side reactions in conventional electrolytes, which greatly deteriorate their electrochemical performance. Herein, an in situ “anchoring + pouring” synergistic cathode-electrolyte interphase (CEI) construction is realized by using 1,3,6-hexanetricarbonitrile (HTCN) and tris(trimethylsilyl) phosphate (TMSP) electrolyte additives to alleviate the challenges of an LLO (Li 1.13 Mn 0.517 Ni 0.256 Co 0.097 O 2 ). HTCN with three nitrile groups can tightly anchor transition metals by coordinative interaction to form the CEI framework, and TMSP will electrochemically decompose to reshape the CEI layer. The uniform and robust in situ constructed CEI layer can suppress the transition metal dissolution, shield the cathode against diverse side reactions, and significantly improve the overall electrochemical performance of the cathode with a discharge voltage decay of only 0.5 mV/cycle -1 . Further investigations based on a series of experimental techniques and theoretical calculations have revealed the composition of in situ constructed CEI layers and their distribution, including the enhanced HTCN anchoring effect after lattice densification of LLOs. Finally, this study provides insights into the in situ CEI construction for enhancing the performance of high-energy and high-voltage cathode materials through effective, convenient and economical electrolyte approaches.

25 ENERGY STORAGE↗
DOE OSTI2022

Transferring Liquid Metal to form a Hybrid Solid Electrolyte via a Wettability-Tuning Technology for Lithium-Metal Anodes

Integrating solid-state electrolyte (SSE) into Li-metal anodes has demonstrated great promise to unleash the high energy density of rechargeable Li-metal batteries. However, fabricating a highly cyclable SSE/Li-metal anode remains a major challenge because the densification of the SSE is usually incompatible with the reactive Li metal. Here, a liquid-metal-derived hybrid solid electrolyte (HSE) is proposed, and a facile transfer technology to construct an artificial HSE on the Li metal is reported. By tuning the wettability of the transfer substrates, electron- and ion-conductive liquid metal is sandwiched between electron-insulating and ion-conductive LiF and oxides to form the HSE. The transfer technology renders the HSE continuous, dense, and uniform. The HSE, having high ion transport, electron shut-off, and mechanical strength, makes the composite anode deliver excellent cyclability for over 4000 h at 0.5 mA cm(-2) and 1 mAh cm(-2) in a symmetrical cell. When pairing with LiFePO4 and sulfur cathodes, the HSE-coated Li metal dramatically enhances the performance of full cells. Therefore, this work demonstrates that tuning the interfacial wetting properties provides an alternate approach to build a robust solid electrolyte, which enables highly efficient Li-metal anodes.

li-metal anodes↗
DOE OSTI2025

A New Family of Ternary Intermetallic Compounds with Dualistic Atomic Ordering – The ZIP Phases

A new family of nanostructured ternary intermetallic compounds − named the ZIP phases − is introduced in this work. The ZIP phases exhibit dualistic atomic ordering, i.e., they form two structural variants: one with the fcc diamond cubic structure (space group Fd$\bar{3}$m) and one with the hexagonal structure (space group P6 3 /mmc). They are also characterized by metallic behavior, ionic bonding, and atomic zigzagging. Powder metallurgical routes involving pressure-assisted densification are adopted to demonstrate ZIP phase synthesis in the Nb-Si-Ni, Nb-Si-Co, Ta-Si-Ni, V-Si-Ni, and Nb-Si-Fe ternary systems. Crucially, reactive hot pressing is capable of producing high-purity ZIP phase materials after the judicious, elemental system-specific optimization of the processing route. Synthesis of phase-pure materials – demonstrated in the Nb-Si-Ni ternary system by the synthesis of quasi phase-pure Nb 3 SiNi 2 and Ni 3 SiNb 2 ZIP phase-based materials – is a steppingstone to the prospective exploitation of the ZIP phases. Characterization of Nb 3 SiNi 2 and Ni 3 SiNb 2 involves crystal structure determination, spatially resolved chemical analysis, and determination of select thermal, electrical, magnetic, mechanical, and physical properties. Density functional theory is used to assess the stability of Nb 3 SiNi 2 & Ni 3 SiNb 2 and derivative binary compounds at different temperatures, also exploring the exfoliation of these two ZIP phases along specific surfaces to produce 2D derivatives.

Intermetallic compounds (IMCs)↗
DOE OSTI2025

Demonstration of the Reproducibility Challenges in the Sintering Behavior of Lithium‐Stuffed Garnets in Scaling up Synthesis

Lithium-stuffed garnets, such as Li 7 La 3 Zr 2 O 12 (LLZO), are promising candidates for next-generation solid-state batteries because of their high room-temperature ionic conductivity and chemical stability against lithium metal anodes, which are crucial for achieving higher energy density. However, realizing LLZO's potential in practical devices requires synthesis methods that can be scaled reliably to large batch sizes for manufacturing. Herein, we investigate the sintering reproducibility of LLZO synthesized at larger scales using ultrasonic spray pyrolysis, a cost-effective and scalable synthesis route. Two 100 g batches of Al-doped LLZO are prepared and their sintering behavior is examined in detail. Both Al-LLZO batches contain over 90 wt.% cubic-phase LLZO, and both batches exhibit room temperature conductivities greater than 1 × 10 −4 S cm −1 at a relative density above 0.8. However, variations in secondary phases and subtle differences in Al content lead to significant differences in densification and microstructure. These results demonstrate that LLZO's sintering behavior is highly sensitive to small changes in secondary phases and Al content, creating reproducibility challenges when moving from laboratory- to manufacturing-scale synthesis.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Distinct Melt Infusion Architectures of Antiperovskite Solid Electrolytes

Antiperovskite solid electrolytes are an emerging class of lithium‐ion conductors distinguished by their unusually low melting points, enabling scalable, low‐temperature processing routes not accessible to most solid electrolytes. In this work, we synthesize phase‐pure chloride (Cl), bromide (Br), and mixed halide (ClBr) variants of antiperovskites and investigate their ionic conductivities in both powder and hot‐pressed forms. Hot pressing significantly enhances conductivity across all compositions, while energy‐dispersive X‐ray spectroscopy (EDS) of the mixed halide system reveals halide surface migration during densification. We further investigate the melt‐infiltration behavior of these electrolytes into substrates relevant to solid‐state battery architectures, including Al and Cu current collectors, conventional NMC and LFP cathodes, and a foamed NMC cathode with a highly porous architecture. The foamed cathode enables deep and uniform electrolyte penetration, highlighting the role of electrode architecture in facilitating melt infiltration. Across all substrates, electrolyte halide chemistry strongly influences wetting behavior, penetration depth, and resulting microstructural morphology. Together, these results establish clear processing–structure relationships for melt‐infiltrated antiperovskite solid electrolytes and demonstrate how electrolyte chemistry and electrode architecture govern interfacial morphology during integration, providing practical guidelines for processing and structural design in solid‐state battery systems.

antiperovskite↗
DOE OSTI2024

Quantifying the cooperative evolution of microphase segregation and nanostructural order in annealed polyurethanes of MDI-BDO-PTHF

Here, we quantify the relationship between microphase segregation and local structure development in thermoplastic polyurethanes. Samples were prepared with varying ratios of 4,40 -methylene diphenyl diisocyanate (MDI) and 1,4-butanediol (BDO) to polytetrahydrofuran (PTHF) and annealed at temperatures T a between RT–140 °C for 20 h each. Distinct populations of smaller and larger ordered domains are distinguished by pair distribution func tion analysis. The intermediate-range order of nanoscale hard domains in the paracrystalline state (form I) is directly extracted and characterized. The results suggest that form I of the MDI-BDO:PTHF system presents a conformational and packing order similar to the form III structure, typically obtained from stretching/annealing, but with limited spatial coherence of 3–7 nm. Heating above T g of the hard segments is necessary to achieve a substantial structural response from the annealing treatment. Increasing T a promotes purification of the soft phase via microphase segregation, coalescence of the hard blocks, and growth of paracrystalline phase, while a minority fraction of longer-range ordered domains left over from production remains relatively constant. We observe a composition-dependent decrease in the average nearest-neighbor dis tance that can be correlated with the greater number of C C, C N, and C O bonds with increased hard segment content. A non-linear deviation in the trend is observed to correlate with sample densification. The mechanical and thermal behavior of the samples is intimately tied to the segregation state.

processing-structure-properties↗
DOE OSTI2024

Recent Progress on Dominant Sulfide‐Type Solid‐State Na Superionic Conductors for Solid‐State Sodium Batteries

Abstract Over the past decade, solid‐state batteries have garnered significant attentions due to their potentials to deliver high energy density and excellent safety. Considering the abundant sodium (Na) resources in contrast to lithium (Li), the development of sodium‐based batteries has become increasingly appealing. Sulfide‐based superionic conductors are widely considered as promising solid eletcrolytes (SEs) in solid‐state Na batteries due to the features of high ionic conductivity and cold‐press densification. In recent years, tremendous efforts have been made to investigate sulfide‐based Na‐ion conductors on their synthesis, compositions, conductivity, and the feasibility in batteries. However, there are still several challenges to overcome for their practical applications in high performance solid‐state Na batteries. This article provides a comprehensive update on the synthesis, structure, and properties of three dominant sulfide‐based Na‐ion conductors (Na 3 PS 4 , Na 3 SbS 4 , and Na 11 Sn 2 PS 12 ), and their families that have a variety of anion and cation doping. Additionally, the interface stability of these sulfide electrolytes toward the anode is reviewed, as well as the electrochemical performance of solid‐state Na batteries based on different types of cathode materials (metal sulfides, oxides, and organics). Finally, the perspective and outlook for the development and practical utilization of sulfide‐based SE in solid‐state batteries are discussed.

Guo, Xiaolin↗
DOE OSTI2022

Exploring the Microstructure-Property Relationship of Mg-Al-Mn alloys enhanced via Friction Stir Processing

Friction Stir Processing (FSP) is a solid-state thermomechanical processing technique that enables local grain refinement, densification, and homogenization of microstructure in metallic components. Here, FSP is applied to thin sheets of high-pressure die cast AM60 to address the porosity and heterogeneities inherent to the casting process. In this work, microstructure characterization is correlated to improvements in the static mechanical properties of the Mg-Al-Mn alloy system at various FSP processing conditions. Notably, there is a significant increase in the ductility and ultimate tensile stress of system following FSP. The dominant deformation mechanisms for the as-cast material and the FSP material are investigated. Finally, the fatigue life improvement is correlated to microstructure modifications that may lead to distinct behavior in crack initiation and crack propagation for the as-cast and FSP material.

Garcia, David↗
DOE OSTI2023

Solid Phase Processing of Mg-Al-Mn-Ca for High Strength and Ductility

While rare-earth Mg alloys have remarkable properties for high strength applications, lower cost alternatives are necessary for the widespread industry use of Mg. Ca added Mg alloys have shown promise as an alternative to rare-earth alloys. Ca-based precipitates can reduce basal texture, reduce casting porosity, and increase mechanical strength. However, the accumulation of Ca-based precipitates along inter-dendritic regions can severely limit ductility. Here, we apply two solid phase processing techniques, friction stir processing and shear assisted processing and extrusion, to produce wrought microstructure sheet and extruded tubes from a cast Mg-Al-Mn-Ca alloy. Ductility of the alloy is enhanced by densification under applied force and elevated temperature, grain refinement, and refinement of (Al,Mg)-Ca based precipitate.

Garcia, David↗
DOE OSTI2021

Effects of a Pressurized Water Treatment on Internal Gelation Sol-Gel Microspheres

Based on previous observations that a pressurized water treatment (PWT) prevented cracking of sol-gel microspheres, we investigated the effects of a PWT on microsphere crystallinity, density, and specific surface area (SSA). Results were used to determine how a PWT alters the properties of microspheres upon drying and heating. Microspheres with diameters near 100-200 µm were prepared with and without a PWT and measured using x-ray diffraction (XRD), transmission electron microscopy (TEM), nitrogen adsorption (BET), and pycnometry. Properties of air-dried microspheres processed with and without a PWT are compared. Additionally, the properties of microspheres processed using a PWT are reported after heating to 150 °C, 450 °C, 750 °C, 1050 °C, and 1350 °C. X-ray diffraction measurements indicate that the PWT step improves the crystallinity of air-dried microspheres. XRD data was also used to calculate crystallite size, which increases with higher heat treatment temperatures. TEM images support crystallite size calculations from XRD data and provide an indication of the range of crystallite sizes, particularly for samples processed at higher temperatures where crystallite sizes are too large for estimation using the Scherrer formula. Density and SSA measurements performed as a function of heat treatment temperature indicate that a PWT increases the density of air-dried microspheres, creates a pore network, and that significant densification occurs between 450 - 750 °C. These results may be used to inform decisions on internal gelation flowsheet parameters to optimize the microsphere formation and gelation step, prevent microsphere cracking, and produce microspheres suitable for subsequent coating operations or pressing into pellets.

cerium oxide, TRISO, internal gelation, nuclear fu↗
DOE OSTI2020

Ultrahigh temperature in situ transmission electron microscopy based bicrystal coble creep in Zirconia II: Interfacial thermodynamics and transport mechanisms

This work uses a combination of stress dependent single grain boundary Coble creep and zero-creep experiments to measure interfacial energies, along with grain boundary point defect formation and migration volumes in cubic ZrO 2 . These data, along with interfacial diffusivities measured in a companion paper are then applied to analyzing two-particle sintering. The analysis presented here indicates that the large activation volume, v * = v f + v m primarily derives from a large migration volume and suggests that the grain boundary rate limiting defects are delocalized, possibly due to electrostatic interactions between charge compensating defects. The discrete nature of the sintering and creep process observed in the small-scale experiments supports the hypothesis that grain boundary dislocations serve as sources and sinks for grain boundary point defects and facilitate strain during sintering and Coble creep. Model two-particle sintering experiments demonstrate that initial-stage densification follows interface reaction rate-limited kinetics.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Bulk nanocrystalline Al alloys with hierarchical reinforcement structures via grain boundary segregation and complexion formation

Grain size engineering, particularly reducing grain size into the nanocrystalline regime, offers a promising pathway to further improve the strength-to-weight ratio of Al alloys. Unfortunately, the fabrication of nanocrystalline metals often requires non-equilibrium processing routes, which typically limit the specimen size and require large energy budgets. In this study, multiple dopant elements in ternary Al alloys are deliberately selected to enable segregation to the grain boundary region and promote the formation of amorphous complexions. Three different fully dense bulk nanocrystalline Al alloys (Al-Mg-Y, Al-Fe-Y, and Al-Ni-Y) with small grain sizes were successfully fabricated using a simple powder metallurgy approach, with full densification connected directly to the onset of amorphous complexion formation. All the compositions demonstrate densities above 99% with grain sizes <60 nm following consolidation via hot pressing at 585 °C. The very fine grain structure results in excellent mechanical properties, as evidenced by nanoindentation hardness values in the range of 2.2-2.8 GPa. Detailed microstructural characterization verifies the segregation of all dopant species to grain boundaries as well as the formation of amorphous complexions, which suggests their influential role in aiding effective consolidation and endowing thermal stability in the alloys. Moreover, nanorods with a core-shell structure are also observed at the grain boundaries, which likely contribute to the stabilization of the grain structure while also strengthening the materials. Lastly, intermetallic particles with sizes of hundreds of nanometers form in all systems. As a whole, the results presented here demonstrate a general alloy design strategy of segregation and boundary evolution pathway that enables the fabrication of multiple nanocrystalline Al alloys with hierarchical microstructures and improved performance.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effects of bridging fibers on the evolution of lamellar architecture during H 2 /H 2 O redox cycling of Fe-foams

Fe/Fe 3 O 4 redox cycling via cyclic H 2 /H 2 O exposure at 800 °C is studied in lamellar Fe foams with 15 vol% fibers, created by freeze-casting. Fibers were integrated in the foams to mitigate densification during cycling by mechanically supporting neighboring lamellae, thus preventing buckling and sintering at contact points. Three fiber types are examined: short (0.1 mm) and long (1–2 mm) stainless-steel fibers, and long zirconia fibers. Long fibers bridge lamellae and have a marked effect on the architecture by increasing the initial interlamellar porosity (from < 60 to > 85%), with a corresponding decrease in foam shrinkage during initial reduction and sintering (from > 80 to < 55% volumetric loss). Though performance improves as compared to fiber-free foams, fiber effectiveness against damage decreases with cycling: after 10 redox cycles, porosity falls from 85 to 50% for foams with long fibers. One novel degradation mechanism is identified: fiber engulfment. This mechanism occurs over successive redox cycles, as material from the lamellae cyclically engulfs (as Fe 3 O 4 ) and withdraws (as Fe) from the fibers, with a net transport from lamellae to fibers after each cycle. Finally, this cyclic coarsening mechanism alters foam architecture from bridged-lamellar (with evenly distributed porosity) to mixed lamellar/fibrous (with unevenly distributed porosity).

36 MATERIALS SCIENCE↗
DOE OSTI2025

Understanding coarsening of a post-corrosion microstructure in a molten salt by combining phase-field modeling and in situ tomography

Alloys corroding in molten salt have been observed to form bicontinuous, nanoporous microstructures via dealloying, which subsequently undergo coarsening due to facile transport in high-temperature conditions. In this work, we describe a methodology to elucidate the underlying transport mechanisms during coarsening of a bicontinuous microstructure via quantitative comparisons between phase-field simulations and four-dimensional in situ experiments, in this case X-ray nanotomography of the coarsening of a dealloyed 80 wt% Ni-20 wt% Cr microwire in molten KCl-MgCl 2 at 800°C. We conduct phase-field simulations initialized from experimental data to model coarsening via three different transport mechanisms: surface diffusion, solid bulk diffusion, and liquid bulk diffusion. These simulations reproduce key features of the experiment, such as the densification of the outer layer of the dealloyed wire and the reduction in radius over time. We quantitatively compare different microstructural characteristics between the simulations and experiment and extract temporal scaling factors that optimally match the time scales of the simulations to that of the experiment. This allows us to evaluate morphological similarity between the simulations and experiment and relate the experimental coarsening kinetics to fundamental material properties. We find that surface diffusion is most likely to be the dominant coarsening mechanism, and its kinetics imply a surface diffusivity of D S = 8.9 x 10 -20 m 3 /s, which is within the range of reported values for Ni-vacuum interfaces at 800°C. However, the difference between the experiment and the surface diffusion simulation increases substantially at late times, suggesting that other mechanisms, such as the dissolution of residual Cr, may be at play.

36 MATERIALS SCIENCE↗