Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “data normalization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

The addition of visible channel data to satellite infrared rain estimation schemes

The effect of adding visible channel (VIS) data to the IR data in satellite rain estimation schemes was investigated by comparing the abilities of satellite threshold schemes based on VIS, IR channel, or bispectral (VIS/IR) data to estimate convective precipitation. Using the methodology of Bellon and Austin (1986), empirical relationships between the satellite and radar data were determined for two areas: the Florida Area Cumulus Experiment (FACE) area and a 25-km area on a side centered on 26 N, 81 W, which was inclusive of the FACE area but exclusive of points within 50 km or greater than 170 km of the Miami WSR-57 radar. The results did not demonstrate an unequivocal effect of VIS data. The normalized rms error data for the three estimation schemes used in a four-day experiment are presented.

Negri, Andrew J.↗
NASA NTRS1977

A review of current procedures for normalizing aircraft flyover noise data to reference meteorological conditions

Procedures that are currently used to normalize raw aircraft noise data to reference weather conditions are reviewed. These procedures sometimes result in calculated values of molecular absorption which differ from measured values, especially at higher frequencies. An explanation is offered for this discrepancy, and its effect on normalized sound levels and on calculations of effective perceived noise level is examined.

Deloach, R.↗
NASA NTRS2013

Modeling Longitudinal Data Containing Non-Normal Within Subject Errors

The mission of the National Aeronautics and Space Administration’s (NASA) human research program is to advance safe human spaceflight. This involves conducting experiments, collecting data, and analyzing data. The data are longitudinal and result from a relatively few number of subjects; typically 10 – 20. A longitudinal study refers to an investigation where participant outcomes and possibly treatments are collected at multiple follow-up times. Standard statistical designs such as mean regression with random effects and mixed–effects regression are inadequate for such data because the population is typically not approximately normally distributed. Hence, more advanced data analysis methods are necessary. This research focuses on four such methods for longitudinal data analysis: the recently proposed linear quantile mixed models (lqmm) by Geraci and Bottai (2013), quantile regression, multilevel mixed–effects linear regression, and robust regression. This research also provides computational algorithms for longitudinal data that scientists can directly use for human spaceflight and other longitudinal data applications, then presents statistical evidence that verifies which method is best for specific situations. This advances the study of longitudinal data in a broad range of applications including applications in the sciences, technology, engineering and mathematics fields.

Feiveson, Alan↗
NASA NTRS1974

Pioneer 10 mission - Summary of scientific results from the encounter with Jupiter

Data on the Jovian atmosphere and radiation environment transmitted by Pioneer 10 as it passed by Jupiter are discussed. The presence of a strong magnetic field, of energetic electron precursers, and of flat disk-shaped particle distribution is noted at a distance of 360 Jovian radii from the planet. Previously available data on Jovian satellites are augmented from Pioneer 10 data. The normal operation of the data collecting and transmitting systems of the mission after encounter with Jupiter is noted.

Opp, A. G.↗
NASA NTRS1983

Global multispectral mosaics of the icy Galilean satellites

Multispectral mosaics of the three icy Galilean satellites have been produced from low- to moderate-resolution Voyager images. The digital image data have been calibrated using preflight and in-flight calibration data, and reduced to normal albedos for four-color band passes, centered at 0.35, 0.41, 0.48, and 0.59 microns. The individual images have been geometrically corrected, mosaiked, and presented in a normal cylindrical map projection at a uniform scale of 8 km/pixel. Preliminary analysis of the normal albedo data shows that (1) the darkest terrains on the satellites are the dark regions on Callisto, (2) the brightest regions are bright plains regions on Europa and bright, fresh craters on Ganymede, (3) bright craters on Ganymede and its dark, cratered regions are both significantly brighter than comparable terrains on Callisto, and (4) Europa exhibits several distinct spectral units, with regions on the trailing hemisphere having lower relative ultraviolet spectral reflectance than areas on the leading hemisphere. This is consistent with proposals that Io-related plasma impact on Europa's trailing side has altered its optical properties.

Johnson, T. V.↗
NASA NTRS2006

Adaptive Changes In Postural Equilibrium And Motion Sickness Following Repeated Exposures To Virtual Environments

Virtual environments offer unique training opportunities, particularly for training astronauts and preadapting them to the novel sensory conditions of microgravity. Two unresolved human factors issues in virtual reality (VR) systems are: 1) potential "cybersickness", and 2) maladaptive sensorimotor performance following exposure to VR systems. Interestingly, these aftereffects are often quite similar to adaptive sensorimotor responses observed in astronauts during and/or following space flight. Changes in the environmental sensory stimulus conditions and the way we interact with the new stimuli may result in motion sickness, and perceptual, spatial orientation and sensorimotor disturbances. Initial interpretation of novel sensory information may be inappropriate and result in perceptual errors. Active exploratory behavior in a new environment, with resulting feedback and the formation of new associations between sensory inputs and response outputs, promotes appropriate perception and motor control in the new environment. Thus, people adapt to consistent, sustained alterations of sensory input such as those produced by microgravity, unilateral labyrinthectomy and experimentally produced stimulus rearrangements. Adaptation is revealed by aftereffects including perceptual disturbances and sensorimotor control disturbances. The purpose of the current study was to compare disturbances in postural control produced by dome and head-mounted virtual environment displays, and to examine the effects of exposure duration, and repeated exposures to VR systems. Forty-one subjects (21 men, 20 women) participated in the study with an age range of 21-49 years old. One training session was completed in order to achieve stable performance on the posture and VR tasks before participating in the experimental sessions. Three experimental sessions were performed each separated by one day. The subjects performed a navigation and pick and place task in either a dome or head-mounted display (HMD) VR system for either 30 or 60 min. The environment was a square room with 15 pedestals on two opposite walls. The objects appeared on one set of pedestals and the subject s objective was to move the objects to the other set of pedestals. After the subject picked up an object, a pathway appeared and they were required to follow the pathway to the other side of the room. The subject was instructed to perform the task as quickly and accurately as possible, avoiding hitting walls and other any obstacles and placing the object on the center of the pedestal. Postural equilibrium was measured (using the Equitest CDP balance system, Neurocom, International) before, immediately after, and at 1 hr, 2 hr, 4 hr and 6 hr following exposure to VR. Postural equilibrium was measured during quiet stance with eyes open, eyes closed and vision and/or ankle proprioceptive inputs selectively altered by servo-controlling the visual surround and/or support surface to the subject s center of mass sway. Posture data was normalized using a log transformation and motion sickness data were normalized using the square root. In general, we found that exposure to VR resulted in decrements in postural stability. The largest decrements were observed in the tests performed immediately following exposure to VR and showed a fairly rapid recovery across the remaining test sessions. In addition, subjects generally showed improvement across days. We found significant main effects for day and time for the composite equilibrium score and for sensory organization tests (SOT) 1, 2 and 6. Significant main effects were observed for day for SOT 3 and 5. Although we found no significant main effects for gender (when center of gravity was used as a covariate), we did observe significant gender X time interaction effects for composite equilibrium and for SOT 1, 3, 4 and 5. Women appeared to show larger decrements in postural stability immediately after exposure to VR than men, but recover more quickly than n. Finally, we found no significant main effects for type of VR device or for exposure duration, however, these factors did interact with other factors during some of the SOTs. Subjects exhibited rapid recovery of motion sickness symptoms across time following exposure to VR and significantly less severe symptoms across days. We did not observe main effects for gender, type of device or duration of exposure. Individuals recovered from the detrimental effects of exposure to virtual reality on postural control and motion sickness within one hour. Sickness severity and initial decrements in postural equilibrium decreases over days, which suggests that subjects become dual-adapted over time. These findings provide some direction for developing training schedules for VR users that facilitate adaptation, and support the idea that preflight training of astronauts may serve as useful countermeasure for the sensorimotor effects of space flight.

Harm, D. L.↗
NASA NTRS2012

Evaluation of Delamination Growth Characterization Methods Under Mode I Fatigue Loading

Reliable delamination characterization data for laminated composites are needed for input to analytical models of structures to predict delamination. The double-cantilevered beam (DCB) specimen is used with laminated composites to measure fracture toughness, G(sub Ic), delamination onset strain energy release rate, and growth rate data under cyclic loading. In the current study, DCB specimens of IM7/8552 graphite/epoxy supplied by two different manufacturers were tested in static and fatigue to compare the measured characterization data from the two sources, and to evaluate a proposed ASTM standard for generating Paris Law equations. Static results were used to generate compliance calibration constants for the fatigue data, and a delamination resistance curve, G(sub IR), which was used to determine the effects of fiber-bridging on delamination growth. Specimens were tested in fatigue at a cyclic G(sub Imax) level equal to 50, 40 or 30% of G(sub Ic), to determine a delamination onset curve and delamination growth rate. The delamination onset curve equations had similar exponents and the same trends. Delamination growth rate was calculated by fitting a Paris Law to the da/dN versus G(sub Imax) data. Both a 2-point and a 7-point data reduction method were used and the Paris Law equations were compared. To determine the effects of fiber-bridging, growth rate results were normalized by the delamination resistance curve for each material and compared to the non-normalized results. Paris Law exponents were found to decrease by 31% to 37% due to normalizing the growth data. Normalizing the data also greatly reduced the amount of scatter between the different specimens. Visual data records from the fatigue testing were used to calculate individual compliance calibration constants from the fatigue data for some of the specimens. The resulting da/dN versus G(sub Imax) plots showed much improved repeatability between specimens. Gretchen

Murri, Gretchen B.↗
NASA NTRS1974

Data-matched filter

After amplification and normalization, incoming data bits are fed, alternately, to pair of integrators. While one integrator is operating, content of other is on hold, sample, and dump. Clock derived in bit-timing extractor times and controls integrators. Frequency of clock is one-half data rate.

Scheinberg, N. R.↗
NASA NTRS1975

Large Area Crop Inventory Experiment (LACIE). LANDSAT 3X gain study

The author has identified the following results. The maximum likelihood classifier on the ERIPS failed to show any improvement in accuracy when comparing high-gain LANDSAT data with the simulated normal-gain data. Even if an improvement in accuracy had been detected, the timespan within the crop growing season when the use of high-gain data could be advantageous is limited. A total of six sets of LANDSAT-1 imagery is available for the analysis of gain effects. Three of the sets are high-gain data in MSS bands 4 and 5, whereas the other three are simulated normal-gain. The four sets obtained over Imperial Valley have good supporting ground truth information for training; the two sets over Kansas do not. The use of various combinations of the six data sets is recommended in order to uncover the possible advantages of using the data.

Source record↗
DOE OSTI2026

Poisson Log-Normal Process for Count Data Prediction

Modeling count data is important in physics and other scientific disciplines, where measurements often involve discrete, non-negative quantities such as photon or neutrino detection events. Traditional parametric approaches can be trained to generate integer-count predictions but may struggle with capturing complex, non-linear dependencies often observed in the data. Gaussian process (GP) regression provides a robust non-parametric alternative to modeling continuous data; however, it cannot generate integer outputs. We propose the Poisson Log-Normal (PoLoN) process, a framework that employs GP to model Poisson log-rates. As in GP regression, our approach relies on the correlations between data points captured via GP kernel structure rather than explicit functional parameterizations. We demonstrate that the PoLoN predictive distribution is Poisson-LogNormal and provide an algorithm for optimizing kernel hyperparameters. Furthermore, we adapt the PoLoN approach to the problem of detecting weak localized signals superimposed on a smoothly varying background - a task of considerable interest in many areas of science and engineering. Our framework allows us to predict the strength, location and width of the detected signals. We evaluate PoLoN's performance using both synthetic and real-world datasets, including the open dataset from CERN which was used to detect the Higgs boson at the Large Hadron Collider. Our results indicate that the PoLoN process can be used as a non-parametric alternative for analyzing, predicting, and extracting signals from integer-valued data.

Saha, Anushka [Rutgers U., Piscataway]↗
DOE OSTI2025

Modeling of Vertical Motor-driven Pump for Simulation of a Fault Signature \\ for Condition Monitoring

As part of the ongoing effort to transition from preventive maintenance strategies to condition-based maintenance strategies in nuclear power plants, there is significant reliance on using machine learning techniques. To develop a robust machine learning model that can diagnose all the fault modes of a vertical motor-driven pump, data capturing the unique signature of each fault mode is required. In practice, it is difficult to collect or capture data that captures all the fault modes from a single plant site. So to address this situation, a computational model of a vertical motor-driven pump is developed using the multipurpose finite element software COMSOL Multiphysics. The developed model is used to generate simulated data under normal operation and is compared with the vibration data collected using vibration sensors. Once the simulation model is verified under normal operating condition, simulated data for the fault mode for which minimal or no evidence is available in historical plant process data is developed. This simulated data is used to develop fault signatures to achieve robust predictive models. This paper presents modeling details and verification of the model that can used to generate data for fault modes that are not available at a plant site for condition monitoring purpose.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗
NASA NTRS2006

Simulating Visible/Infrared Imager Radiometer Suite Normalized Difference Vegetation Index Data Using Hyperion and MODIS

The success of MODIS (the Moderate Resolution Imaging Spectrometer) in creating unprecedented, timely, high-quality data for vegetation and other studies has created great anticipation for data from VIIRS (the Visible/Infrared Imager Radiometer Suite). VIIRS will be carried onboard the joint NASA/Department of Defense/National Oceanic and Atmospheric Administration NPP (NPOESS (National Polar-orbiting Operational Environmental Satellite System) Preparatory Project). Because the VIIRS instruments will have lower spatial resolution than the current MODIS instruments 400 m versus 250 m at nadir for the channels used to generate Normalized Difference Vegetation Index data, scientists need the answer to this question: how will the change in resolution affect vegetation studies? By using simulated VIIRS measurements, this question may be answered before the VIIRS instruments are deployed in space. Using simulated VIIRS products, the U.S. Department of Agriculture and other operational agencies can then modify their decision support systems appropriately in preparation for receipt of actual VIIRS data. VIIRS simulations and validations will be based on the ART (Application Research Toolbox), an integrated set of algorithms and models developed in MATLAB(Registerd TradeMark) that enables users to perform a suite of simulations and statistical trade studies on remote sensing systems. Specifically, the ART provides the capability to generate simulated multispectral image products, at various scales, from high spatial hyperspectral and/or multispectral image products. The ART uses acquired ( real ) or synthetic datasets, along with sensor specifications, to create simulated datasets. For existing multispectral sensor systems, the simulated data products are used for comparison, verification, and validation of the simulated system s actual products. VIIRS simulations will be performed using Hyperion and MODIS datasets. The hyperspectral and hyperspatial properties of Hyperion data will be used to produce simulated MODIS and VIIRS products. Hyperion-derived MODIS data will be compared with near-coincident MODIS collects to validate both spectral and spatial synthesis, which will ascertain the accuracy of converting from MODIS to VIIRS. MODIS-derived VIIRS data is needed for global coverage and for the generation of time series for regional and global investigations. These types of simulations will have errors associated with aliasing for some scene types. This study will help quantify these errors and will identify cases where high-quality, MODIS-derived VIIRS data will be available.

Ross, Kenton W.↗
NASA NTRS1992

Survey Parameters and Availability of Low-level Aeromagnetic Data for Geomagnetic Field Modelling

Since aeromagnetic surveying started immediately after World War II, a considerable area of the earth's surface both onshore (in excess of 25 million sq. km) has been magnetically surveyed. For about the first 15 years or so, fluxgate magnetometers were employed in aeromagnetic surveys, but the introduction of proton free-precession magnetometers resulted in absolute readings being recorded. Proton precession magnetometers have now been replaced to a large extent by the more sensitive optical absorption magnetometers. Some care has to be taken to calibrate aeromagnetic survey systems and this is best done using a calibration range tied to a magnetic observatory so that accuracies of 10nT or better are achieved for the total field values recorded. Survey navigation has always posed a problem for aeromagnetic surveys, especially offshore. Over land, vertically pointed 35 mm cameras were initially used to recover the aircraft track using a combination of aerial photos and topographic maps. Over featureless areas, it was necessary to utilize existing electronic positioning systems such as Loran C or set up special navigation systems. The advent of the satellite-based Global Positioning Systems (GPS) has to a larger extent solved the navigational problem because there is now almost continuous worldwide coverage to 10 m accuracy in the differential mode. The resultant aeromagnetic data is normally compiled into contour maps in which the diurnal variation and aircraft heading effects are removed. The resultant digital data are normally made publicly available both in gridded and profile form along with the published contour maps. Most aeromagnetic coverage has been obtained in the developed western countries, but elsewhere a considerable amount of surveying has been carried out; as an example, some 80 percent of Africa has been surveyed mostly as a result of aid programs. The data is usually held by the national geological survey or equivalent organizations, but in a number of cases the data (e.g., for the Magnetic Anomaly Map of North America) is also held by the World Data Centres.

Hood, Peter↗
NASA NTRS1985

A spectral haze diagnostic feature for normalizing Landsat Thematic Mapper data

The effects of atmospheric haze on Thematic Mapper data, transformed to TM Tasseled Cap features, are illustrated by means of simulation. A spectral feature by which the amount of atmospheric haze may be inferred is derived and described for both simulated and actual TM data. Results presented for two actual TM scenes illustrate the diagnostic feature's sensitivity to changes in haze level as well as its insensitivity to scene-class-related variability. The method by which such a diagnostic feature might be incorporated into a haze normalization procedure is also discussed.

Crist, E. P.↗
NASA NTRS1964

Second and third virial coefficients for hydrogen

Second and third virial coefficients for parahydrogen have been derived from closely spaced PVT data from 24 to 100 "K. They are in good agreement at 100 OK with published data for normal hydrogen. Analytical representations of the combined data from about 20 to 423 "K are presented which may be useful in computation of thermodynamic functions of the gas. These formulas are related to those resulting from the use of the Lennard-Jones potential.

HYDROGEN↗
NASA NTRS1989

Development of a software interface for optical disk archival storage for a new life sciences flight experiments computer

The current Life Sciences Laboratory Equipment (LSLE) microcomputer for life sciences experiment data acquisition is now obsolete. Among the weaknesses of the current microcomputer are small memory size, relatively slow analog data sampling rates, and the lack of a bulk data storage device. While life science investigators normally prefer data to be transmitted to Earth as it is taken, this is not always possible. No down-link exists for experiments performed in the Shuttle middeck region. One important aspect of a replacement microcomputer is provision for in-flight storage of experimental data. The Write Once, Read Many (WORM) optical disk was studied because of its high storage density, data integrity, and the availability of a space-qualified unit. In keeping with the goals for a replacement microcomputer based upon commercially available components and standard interfaces, the system studied includes a Small Computer System Interface (SCSI) for interfacing the WORM drive. The system itself is designed around the STD bus, using readily available boards. Configurations examined were: (1) master processor board and slave processor board with the SCSI interface; (2) master processor with SCSI interface; (3) master processor with SCSI and Direct Memory Access (DMA); (4) master processor controlling a separate STD bus SCSI board; and (5) master processor controlling a separate STD bus SCSI board with DMA.

Bartram, Peter N.↗