Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “circuit stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Nonlinear analysis of a family of LC tuned inverters

Four widely used self-oscillating dc-to-square-wave parallel inverters which employ an inductor-capacitor tuned network to determine the oscillation frequency are reduced to a common equivalent RLC network, The techniques of singular-point analysis and state-plane interpretations are employed to describe the steady-state and transient behavior of these circuits and to elucidate the three possible modes of operation: quasi-harmonic, relaxation, and discontinuous. Design guidelines are provided through a study of the influence of circuit parameter variations on the characteristics of oscillation and on frequency stability. Several examples are provided to illustrate the usefulness of this analysis when studying such problems as transistor emitter-to-base junction breakdown during oscillations and the design of starting circuits to insure self-excited oscillations in these inverters.

Lee, F. C. Y.↗
NASA NTRS1983

Cesium standard for satellite application

A Cesium frequency standard that was developed for satellite applications is discussed. It weighs 23 lbs. and uses 23.5 watts of power, achieves a stability of 1 x ten to the minus 13th power/100,000 seconds, and is radiation hardened. To achieve the weight and reliability requirements, both thick and thin film hybrid circuits were utilized. A crystal oscillator is used to improve short-term stability and performance on a moving platform.

Bloch, M. B.↗
NASA NTRS1972

Discrete component S-band power amplifier

A spacecraft S-band power amplifier for Nimbus satellite is reported that achieves stability by use of moderate Q input and output circuits. The discrete component amplifier uses distributed inductance and small piston capacitors for resonance and impedance matching of the transistor to 50 ohm input and output.

Block, A. F.↗
NASA NTRS1983

High stability amplifier

An electrical RF signal amplifier for providing high temperature stability and RF isolation and comprised of an integrated circuit voltage regulator, a single transistor, and an integrated circuit operational amplifier mounted on a circuit board such that passive circuit elements are located on side of the circuit board while the active circuit elements are located on the other side is described. The active circuit elements are embedded in a common heat sink so that a common temperature reference is provided for changes in ambient temperature. The single transistor and operational amplifier are connected together to form a feedback amplifier powered from the voltage regulator with transistor implementing primarily the desired signal gain while the operational amplifier implements signal isolation. Further RF isolation is provided by the voltage regulator which inhibits cross-talk from other like amplifiers powered from a common power supply. Input and output terminals consisting of coaxial connectors are located on the sides of a housing in which all the circuit components and heat sink are located.

Adams, W. A.↗
NASA NTRS1990

The influence of temperature on the cycle life performance of rechargeable Li-TiS2 cells

The authors report studies on the influence of low temperature on the properties and cycling performance of six selected electrolytes. The electrolytes investigated were 2-MeTHF, EC/2-MeTHF, THF, THF/2-MeTHF, EC/THF, and EC/THF/2-MeTHF. All the electrolytes contained 1.5M LiAsF6. Open circuit stand tests indicated that organic electrolytes exhibited improved stability towards lithium at 10 C. However, cycling of the cells at 10 C did not result in improved cycle life performance.

Shen, D. H.↗
NASA NTRS2005

Laboratory Astrophysics Using a Microcalorimeter and Bragg Crystal Spectrometer on an Electron Beam Ion Trap

We completed modifications to the new microcalorimeter system dedicated for use on the EBIT at NIST, which included: 1) a redesign of the x-ray calibration source from a direct electron impact source to one that irradiates the microcalorimeter with fluorescent x-rays. The resulting calibration lines are free of bremsstrahlung background; 2) the microcalorimeter electronic circuit was significantly improved to ensure long-term stability for lengthy experimental runs

Brinton, John↗
NASA NTRS2000

Discriminator Stabilized Superconductor/Ferroelectric Thin Film Local Oscillator

A tunable local oscillator with a tunable circuit that includes a resonator and a transistor as an active element for oscillation. Tuning of the circuit is achieved with an externally applied dc bias across coupled lines on the resonator. Preferably the resonator is a high temperature superconductor microstrip ring resonator with integral coupled lines formed over a thin film ferroelectric material. A directional coupler samples the output of the oscillator which is fed into a diplexer for determining whether the oscillator is performing at a desired frequency. The high-pass and lowpass outputs of the diplexer are connected to diodes respectively for inputting the sampled signals into a differential operational amplifier. The amplifier compares the sampled signals and emits an output signal if there is a difference between the resonant and crossover frequencies. Based on the sampled signal, a bias supplied to the ring resonator is either increased or decreased for raising or lowering the resonant frequency by decreasing or increasing, respectively, the dielectric constant of the ferroelectric.

Romanofsky, Robert R.↗
NASA NTRS1973

Linearized stability analysis and design of a flyback dc-dc boost regulator.

Analytic expressions for the small-signal power-stage describing functions of a switched dc-dc boost regulator are derived from an approximate continuous circuit model which is developed by a time-averaging technique. Closed-loop stability is attained through the design of frequency compensation of the loop gain. Open- and closed-loop regulator output impedances are derived from the linearized models for the given configuration. The analysis and design are compared with and confirmed by breadboard measurements.

Wester, G. W.↗
NASA NTRS1962

STABILITY OF FILM BOILING TWO-PHASE FLOW IN CRYOGENIC SYSTEMS

The stability of film boiling two phase flow is investigated referring in particular to saturated cryogenic liquids. This type of fluid motion is unstable, such that a range of wave numbers will always be present in which disturbances are amplified. Further the mode of operation of the energy supply system may favour temperature fluctuations of large amplitude if the circuit does not provide feed-back compensation. The theoretically predicted stabilization due to capillarity is reduced considerably in liquefied gases with low surface tension, such as hydrogen. This effect causes the transition to turbulent flow to occur at low Reynolds numbers, and increases the heat transport in the turbulent regime. A comparison with experimental data, (horizontal cylinder), shows that the "critical" film Reynolds number ūδ/𝜈, at which instabilities become effective, is lowered from approximately 200, (O2), to about 30, (H2). Similar results have been found with other configurations. Therefore application of laminar film boiling solutions is restricted to small objects, entrance regions, or stagnation points. Turbulent correlations given so far are valid only for a certain group of substances with similar behavior.

LIQUID FLOW↗
NASA NTRS1990

Improved low frequency stability of bolometric detectors

An ac bridge readout system has been developed that greatly improves the low-frequency stability of bolometric detectors. The readout can be implemented with a simple circuit appropriate for use in space applications. A matched pair of detectors was used in the readout to achieve system noise within a factor of two of the fundamental noise limit of the detectors at frequencies as low as 10 mHz. The low-frequency stability of the readout system allows slower, more sensitive detectors to be used in many applications, and it facilitates observing strategies that are well suited to spaceborne observations.

Wilbanks, T.↗
NASA NTRS1981

Simple JFET oscillator

Device used in mixers, modulators, and function generators provides stable sine-wave signal compatible with both integrated circuits and discrete-component assemblies. Oscillator's frequency is tunable over narrow band about design value. Frequency range, stability, linearity, and low power drain of device are suited to communications receivers and transmitters and digital microprocessors, computers, and displays. Circuit simplicity allows for easy monolithic construction.

Kleinberg, L. L.↗
NASA NTRS1964

Emission tester for high-power vacuum tubes

A simple emission-testing circuit for high power vacuum tubes to check their output stability is described. With modification it may be useful in testing mercury-arc rectifiers.

Lundy, C.↗
NASA NTRS1987

Electronically Tuned Microwave Oscillator

Features include low phase noise and frequency stability. Bias-tuned, low-phase-noise microwave oscillator circuit based on npn bipolar transistor and dielectric resonator. Operating at frequency of about 8.4 GHz, oscillator adjusted to give low phase noise, relatively flat power output versus frequency, and nearly linear frequency versus bias voltage.

Lakshminarayana, Mysore↗
NASA NTRS2004

Laboratory Astrophysics using a Microcalorimeter and Bragg Crystal Spectrometer on an Electron Beam Ion Trap

When we last reported, our new microcalorimeter system was being prepared for delivery and permanent installation at the NIST EBIT. This occurred in June 2003 and check-out with the internal calibration source and EBIT plasma x-rays took place over the next several months during which time we modified several component parts to improve the performance. These changes included: 1) A redesign of the x-ray calibration source from a direct electron impact source to one that irradiates the microcalorimeter with fluorescent x-rays. The resulting calibration lines are free of bremsstrahlung background; 2) The microcalorimeter electronic circuit has been significantly improved to ensure long-term stability for the lengthy upcoming runs of the EBIT. Both the preamplifier feedback resistors were changed and the first stage of the preamplifier redesigned. Several photos of the new system are shown in slides 3 and 4. This microcalorimeter spectrometer only requires helium refills every three days (as opposed to every 24 hours in our earlier system) and it will hold a temperature of 65 mK for up to 48 hours (as opposed to 8 hours). Consequently, the efficiency of data acquisition will improve dramatically. The first x-ray spectra of the new calibration source made with the 4-element detector array is shown. An example of the temperature control capabilities of the ADR for a 23 hour interval is shown. The horizontal line shows the temperature stability (about +/- 3 micro kelvin). There are a few short-lived heating excursions caused by technical staff working on the EBIT machine simultaneously. During actual experimental runs these are absent. This temporal profile was interrupted to test additional components of the system; otherwise, the temperature controlling would have continued for another 24 hours.

Silver, Eric↗
NASA NTRS2022

The Promise of Alloy Anodes for Solid-State Batteries

Solid-state batteries are anext-generation technology that could featureimproved safety and energy density, but reliably integrating high-capacity electrode materials to enable high energy while retaining stablelong-termcycling remains a challenge. Anode materials that alloy with lithium, such as silicon, tin, and aluminum,offer high capacity that canyield high-energy battery cells. The use of alloy anodes in solid-state batteries potentially offers major mechanistic benefits compared to other anode contendersand battery systems, such as lithium metal in solid-state architectures or alloys in liquid-electrolyte batteries. This perspective discusseskey advantagesof alloy anode materials for solid-state batteries, including the avoidance of the short circuiting observed with lithium metal and the chemo-mechanical stabilization of the solid-electrolyte interphase (SEI). We further discuss open research questions and challenges in engineering alloy-anode-based solid-state batteries, with the goal of advancing our understanding and control of alloy anode materialswithin solid-state architectures toward commercial application.

John A Lewis↗
NASA NTRS1977

Photoelectron spectrometer with means for stabilizing sample surface potential

An improved X-ray photoelectron spectrometer is disclosed, which includes circuit means to determine the surface potential of a sample, e.g., an insulator. The circuit means comprise an electron gun, whose potential is modulated at a preselected frequency above and below a selected potential with respect to the spectrometer common potential, e.g., ground. The beam of electrons is directed to the sample surface. The sample's surface potential is offset by an offset power supply with respect to the spectrometer common potential until the ac current which flows through the sample reaches a peak amplitude. A lock-in amplifier is included to measure the ac current in phase with the modulating frequency.

Grunthaner, F. J.↗