Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cents”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Comparison of circadian rhythms in male and female humans

Heart rate (HR) and rectal temperature (RT) data were obtained from 12 female and 27 male subjects. The subjects were housed in a facility where the environment was controlled. Human male and female RT and HR exhibit a circadian rhythm with an excursion of about 1.2 C and 30 beats/min, respectively. The acrophases, amplitudes, and level crossings are only slightly different between the sexes. The male HR and RT circadian wave forms are more stable than those of the females. However, the actual RT and HR of males were always lower than that of females at all time points around the clock. The HR during sleep in females is 15 per cent below the daily mean heart rate and in males, 22 per cent.

Winget, C. M.↗
NASA NTRS1978

Magma production and migration within the moon

Partial melting is likely to have occurred throughout much of the moon due to heating during accretion and the volumetric heating of radioactive isotopes. Important problems that have received relatively little attention concern the migration of the resulting magmas to form surface or near surface volcanic rock. In the paper the basic mechanism for the migration of the magma through the lunar asthenosphere is considered. A porous flow model is proposed. The magma behaves like a liquid flowing through a porous matrix. The volume fraction of liquid present determines the saturated porosity. The differential buoyancy of the magma drives it upwards. It is shown that the per cent partial melt in the lunar interior will only slightly exceed that required to provide interconnecting porosity. Assuming that the radioactive isotopes are preferentially segregated into the magma, the time dependence of the partial melting of the lunar interior is found. It is shown that the total degree of partial melting of the deep lunar interior is likely to be between five and ten per cent.

Turcotte, D. L.↗
NASA NTRS1981

Effect of CeO2, MgO and Y2O3 additions on the sinterability of a milled Si3N4 with 14.5 wt% SiO2

The sinterability of alpha Si3N4 with 0-5.07 equivalent per cent of CeO2, MgO, or Y2O3 has been studied in the temperature range 1650-1820 C by density measurements and X-ray diffraction analysis. Maximum densities were obtained in the range 1765-1820 C and were 99.6% of theoretical with 2.5% CeO2; 98.5% of theoretical with 1.24 to 1.87% MgO, and 99.2% of theoretical with 2.5% Y2O3. Densities 94% or more of theoretical value were obtained with as little as 0.62 equivalent per cent additive.

Arias, A.↗
NASA NTRS1982

Optimal weighting of data to detect climatic change - Application to the carbon dioxide problem

It is suggested that a weighting of surface temperature data, using information about the expected level of warming in different seasons and geographical regions and statistical information about the amount of natural variability in surface temperature, can improve the chances of early detection of carbon dioxide concentration-induced climatic warming. A preliminary analysis of the optimal weighting method presented suggests that it is 25 per cent more effective in revealing surface warming than the conventional method, in virtue of the fact that 25 per cent more data must conventionally be analyzed in order to arrive at a similar probability of detection. An approximate calculation suggests that the warming ought to have already been detected, if the only sources of significant surface temperature variability had time scales of less than one year.

Bell, T. L.↗
NASA NTRS1983

Forecasting tropical cyclone recurvature with upper tropospheric winds

Data from 17 tropical cyclones during the 1974 through 1979 hurricane seasons are used to investigate whether the high level winds far to the northwest, north and northeast of the hurricane center can be used to predict hurricane track recurvature. When the man 200-mb winds 1500 to 2000 km northwest and north of the storm center equal or exceed 20 m/s, 80 per cent of the storms recurved before traveling as much as 12 degrees of longitude farther west. The high winds were also used to predict change in direction of forward motion during the next 72 hours. The regression equations developed explain up to 41 per cent of the variance in future direction. In addition to the geostrophic winds used, winds were also obtained by tracking clouds with successive satellite imagery. The u-components of the satellite winds are highly correlated with the geostrophic winds at 200-mb and could probably be used instead of them when available. The v-components are less highly correlated.

Gentry, R. C.↗
NASA NTRS1984

L Chondrite meteorites: A compilation and preliminary analyses

A compilation of those meteorites currently recognized as being L chondrites, exclusive of the numerous Antarctica finds, was made and is known as the L Chondrite Register. Data for these 576 meteorites was collected from a variety of sources, primarily the British Museum's Catalogue of Meteorites and the Appendix to the Catalogue of Meteorites. Also used was the Revised Cambridge Chondrite Compendium, which provided a convenient listing of L chondrites; other sources include Chinese Meteorites, Meteorites, by Wasson (1974), and the Meteoritical Bulletin of Meteoritics. This last source provided data for most recent falls and was referenced through March of 1982. All such data were recorded on a computer data file with a HP 2647A terminal, so that information could easily be retrieved and manipulated. For each meteorite, the petrographic class, location of find, fall date and hour, mass, mole per cent fayalite, weight per cent Fe, SiO2/MgO ratio, shock class, metal class, 4He abundance, UTh-H3 gas retention age, K-Ar gas retention age, and 21Ne cosmic ray exposure age, was recorded when known.

Silliman, A.↗
NASA NTRS1931

A comparison of the aerodynamic characteristics of the normal and three reflexed airfoils in the variable density wind tunnel

An investigation was made of the aerodynamic effects of reflexing the trailing edge of three commonly used airfoils. Six airfoils were used in the investigation: three having the normal profiles of the Navy 60, the Boeing 106, and the Gottingen 398, and three having these profiles modified to obtain a reflexed trailing edge with the mean camber line changed to give Cmc/4=0. The tests were conducted at a value of the Reynolds Number of approximately 3,100,000 in the variable density wind tunnel of the National Advisory Committee for Aeronautics. Measurements of lift, drag, and pitching moment were made on each of the six airfoils. The expected reduction of the center of pressure travel was obtained. The maximum lift was reduced approximately 12 per cent and the minimum profile drag approximately 4 per cent.

Defoe, George L↗
NASA NTRS1931

Tests of N.A.C.A. airfoils in the variable-density wind tunnel Series 43 and 63

This note is one of a series covering an investigation of a family of related airfoils. It gives in preliminary form the results obtained from tests in the N.A.C.A. Variable-Density Wind Tunnel of two groups of six airfoils each. One group, the 43 series, has a maximum mean camber of 4 per cent of the chord at a position 0.3 of the chord from the leading edge; the other group, the 63 series, has a maximum mean camber of 6 per cent of the chord at the same position. The members within each group differ only in maximum thickness, the maximum thickness/chord ratios being:0.06, 0.09, 0.12, 0.15, 0.18, and 0.21. The results are analyzed with a view to indicating the variation of the aerodynamic characteristics with profile thickness for airfoils having a certain mean camber line.

Jacobs, Eastman N↗
NASA NTRS1931

Tests of N.A.C.A. airfoils in the variable-density wind tunnel Series 45 and 65

This note is one of a series covering an investigation of a number of related airfoils. It presents the results obtained from tests in N.A.C.A. Variable-Density Wind Tunnel of two groups of six airfoils each. One group, the 45 series, has a maximum mean camber of 4 per cent of the chord at a position 0.5 of the chord behind the leading edge, and the other group, the 65 series, has a maximum mean camber of 6 per cent of the chord at the same position. The members within each group differ only in maximum thickness, the maximum thickness/chord ratios being: 0.06, 0.09, 0.12, 0.15, 0.18, and 0.21. The results are analyzed with a view to indicating the variation of the aerodynamic characteristics with profile thickness for airfoils having a certain mean camber line form.

Jacobs, Eastman N↗
NASA NTRS1932

The Effect of Clearance Distribution on the Performance of a Compression-ignition Engine with a Precombustion Chamber

The clearance distribution in a precombustion chamber cylinder head was varied so that for a constant compression ratio of 13.5 the spherical auxiliary chambers contained 20, 35, 50, and 70 per cent of the total clearance volume. Each chamber was connected to the cylinder by a single circular passage, flared at both ends, and of a cross-sectional area proportional to the chamber volume, thereby giving the same calculated air-flow velocity through each passage. Results of engine-performance tests are presented with variations of power, fuel consumption, explosion pressure, rate of pressure rise, ignition lag, heat loss to the cooling water, and motoring characteristics. For good performance the minimum auxiliary chamber volume, with the cylinder head design used, was 35 per cent of the total clearance volume; for larger volumes the performance improves but slightly. With the auxiliary chamber that contained 35 percent of the clearance volume there were obtained the lowest explosion pressures, medium rates of pressure rise, and slightly less than the maximum power. For all clearance distributions an increase in engine speed decreased the ignition lag in seconds and increased the rate of pressure rise.

Moore, C. S.↗
NASA NTRS1932

Effect of length of Handley Page tip slots on the lateral-stability factor, damping in roll

Tests have been made in the NACA 7 by 10 foot wind tunnel on a Clark Y wing model equipped with various lengths of Handley Page slots extending inward from the wing tips. The slot lengths tested ranged from 20 to 100 per cent of the semi span. The effect of slot lengths on damping in roll was determined by means of both free-autorotation and forced-rotation test. In addition, the maximum lift coefficient was found with each slot length. The optimum length of slot for satisfactory damping in roll over a large range of angles of attack was found to be slightly over 50 per cent of the semispan for the form of slot tested.

Weick, Fred E↗
NASA NTRS1923

Performance of B. M. W. 185-Horsepower Airplane Engine

This report deals with the results of a test made upon a B. M. W. Engine in the altitude chamber of the Bureau of Standards, where controlled conditions of temperature and pressure can be made to simulate those of the desired altitude. A remarkably low value of fuel consumption - 041 per B. H. P. hour - is obtained at 1,200 revolutions per minute at an air density of 0.064 pound per cubic foot and a brake thermal efficiency of 33 per cent and an indicated efficiency of 37 per cent at the above speed and density. In spite of the fact that the carburetor adjustment does not permit the air-fuel ratio of maximum economy to be obtained at air densities lower than 0.064, the economy is superior to most engines tested thus far, even at a density lower than 0.064, the economies superior to most engines tested thus far, even at a density (0.03) corresponding to an altitude of 25,000 feet. The brake mean effective pressure even at full throttle is rather low. Since the weight of much of the engine is governed more by its piston displacement than by the power developed, a decreased mean effective pressure usually necessitates increased weight per horsepower. The altitude performance of the engine is, in general, excellent, and its low fuel consumption is the outstanding feature of merit.

Sparrow, S W↗
NASA NTRS1924

Complete Study of Longitudinal Oscillation of a VE-7 Airplane

This investigation was carried out by the National Advisory Committee for Aeronautics at Langley Field in order to study as closely as possible the behavior of an airplane when it was making a longitudinal oscillation. The airspeed, the altitude, the angle with the horizon and the angle of attack were all recorded simultaneously and the resulting curves plotted to the same time scale. The results show that all the curves are very close to damped sine curves, with the curves for height and angle of attack in phase, that for angle with the horizon leading them by 18 per cent and that for path angle leading them by 25 per cent.

Norton, F H↗
NASA NTRS1928

Differential Pressures on a Pitot-venturi and a Pitot-static Nozzle over 360 Degrees Pitch and Yaw

Measurements of the differential pressures on two navy air-speed nozzles, consisting of a Zahm type Pitot-Venturi tube and a SQ-16 two-pronged Pitot-static tube, in a tunnel air stream of fixed speed at various angles of pitch and yaw between 0 degrees and plus or minus 180 degrees. This shows for a range over -20 degrees to +20 degrees pitch and yaw, indicated air speeds varying very slightly over 2 per cent for the Zahm type and a maximum of about 5 per cent for the SQ-16 type from the calibrated speed at 0 degree. For both types of air-speed nozzle the indicated air speed increases slightly as the tubes are pitched or yawed several degrees from their normal 0 degrees altitude, attains a maximum around plus or minus 15 degrees to 25 degrees, declines rapidly therefrom as plus or minus 40 degrees is passed, to zero in the vicinity of plus or minus 70 degrees to 100 degrees, and thence fluctuates irregular from thereabouts to plus or minus 180 degrees. The complete variation in indicated air speed for the two tubes over 360 degree pitch and yaw is graphically portrayed in figures 9 and 10. For the same air speed and 0 degree pitch and yaw the differential pressure of the Zahm type Pitot-Venturi nozzle is about seven times that of the SQ-16 type two-prolonged Pitot-static nozzle.

Bear, R M↗
NASA NTRS1931

Full-Scale Wind-Tunnel Tests with a Series of Propellers of Different Diameters on a Single Fuselage

Aerodynamic tests were made with four geometrically similar metal propellers of different diameters, on a Wright "Whirlwind" J-5 engine in an open cockpit fuselage. The results show little difference in the characteristics of the various propellers, the only one of any importance being an increase of efficiency of the order of 1 per cent for a 5 per cent increase of diameter, within the range of the tests.

Weick, Fred E↗
NASA NTRS1931

Effect of Variation of Chord and Span of Ailerons on Rolling and Yawing Moments at Several Angles of Pitch

This report presents the results of an extension to higher angles of attack of the investigation of the rolling and yawing moments due to ailerons of various chords and spans on two airfoils having the Clark Y and U. S. A. 27 wings. The measurements were made at various angles of pitch but at zero angle of roll and yaw, the wing chord being set at an angle of +4 degrees to the fuselage axis. In the case of the Clark Y airfoil the measurements have been extended to a pitch angle of 40 degrees, using ailerons of span equal to 67 per cent of the wing semispan and chord equal to 20 and 30 per cent of the wing chord. The work was conducted on wing models of 60-inch span and 10-inch chord.

Heald, R H↗
NASA NTRS1932

Effect of variation of chord and span of ailerons on hinge moments at several angles of pitch

This report presents the results of an investigation of the hinge moments of ailerons of various chords and spans on two airfoils having the Clark Y and USA-27 wing sections, supplementing the investigations described in NACA-TR-298 and NACA-TR-343, of the rolling and yawing moments due to similar ailerons on these two airfoil sections. The measurements were made at various angles of pitch, but at zero angle of roll and yaw, the wing chord being set at an angle of +4 degrees to the fuselage axis. In the case of the Clark Y airfoil the measurements have been extended to a pitch angle of 40 degrees, using ailerons of span equal to 67 per cent of the wing semispan and chord equal to 20 and 30 per cent of the wing chord. The investigation was conducted on models of 60-inch span and 10-inch chord, having square tips, no taper in plan form or thickness, zero dihedral, and zero sweepback.

Monish, B H↗
NASA NTRS1932

Wind-Tunnel Tests on Airfoil Boundary Layer Control Using a Backward-Opening Slot

This report presents the results of an investigation to determine the effect of boundary layer control on the lift and drag of an airfoil. Boundary layer control was accomplished by means of a backward-opening slot in the upper surface of the hollow airfoil. Air was caused to flow through this slot by a pressure which was maintained inside the airfoil by a blower. Various slot locations, slot openings, and wing pressures were used. The tests were conducted in the 5-foot atmospheric wind tunnel of the Langley Memorial Aeronautical Laboratory. Under the test conditions, the maximum lift coefficient was increased about 96 per cent for one slot arrangement, and the minimum drag coefficient was decreased about 27 per cent for another, both being compared with the results obtained with the unslotted airfoil. It is believed from this investigation that the above effects may be increased by the use of larger slot openings, better slot locations, multiple slots, improved airfoil profiles, and trailing edge flaps.

Bamber, Millard J↗