Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cavity flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Analyzing Mechanical integrity of Microwave resonant Cavity flowmeter

The microwave resonant cavity flow sensor has been proposed to address the difficulties of measuring high-temperature molten salt flow in reactor vessels. The flow sensor consists of a metallic cylindrical cavity coupled to a microwave waveguide. The cylindrical cavity has one of the flat surfaces thin enough to undergo microscopic deflection due to dynamic pressure of the exerted by the flowing fluid. Deflection of the membrane causes a shift in the microwave resonant frequency. Fluid velocity can be estimated from the calibration curve. The objective of this report is to investigate mechanical integrity of the flowmeter’s membrane. The membrane is a thin stainless-steel circular plate with a clamped edge, subjected to uniform load. By calculating the stress on the plate due to deflection and, comparing the stress to the material ultimate tensile strength and yield strength, it can be estimated if the plate will fail. If the maximum stress is greater than the yield strength, the plate will undergo plastic deformation, and the sensor will be disabled. A stress greater than the ultimate tensile strength will cause the plate to fracture. The stress on the plate was calculated with an analytic closed form solution model, and with COMSOL Structural Mechanics Module which does not involve any approximations. Stresses in both the analytic model and COMSOL numerical model were calculated for stainless steel 316 thin circular plates under room temperature conditions, where the fluid is water. The diameter of the circular plate is approximately one inch, and thickness is 10mil. Fluid flow velocity is in the range from 0.5m/s to 1m/s. The results from the two models are similar. Both the analytic model and COMSOL model showed that maximum stresses on the plate, which are at the radial boundary of the plate, are three orders of magnitude smaller than the yield strength and ultimate tensile strength. This indicates that the sensor is at a low risk of mechanical failure.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1991

Tangential, semisubmerged, and internal store carriage and separation at supersonic speeds

This paper presents a general overview of experimental research conducted in the area of tangential, semisubmerged, and internal store carriage and separation at supersonic speeds. Some of the advantages and disadvantages of tangential and semisubmerged carriage are presented along with a discussion of the interference effects between stores mounted in various arrays. Also included is a review of cavity flow fields that exist at supersonic speeds and a discussion of the effect of cavity size and cavity doors on the separation characteristics of stores. Finally, three passive venting systems are described which can modify the flow field of certain cavities and thus improve the separation characteristics of stores from those cavities.

Wilcox, Floyd J., Jr.↗
NASA NTRS1987

Impeller shroud to casing leakage flow simulations in the Space Shuttle Main Engine high pressure fuel pump

Quasi-three-dimensional Navier-Stokes calculations were carried out for the Space Shuttle Main Engine high-pressure fuel pump to simulate the impeller shroud to casing leakage flow. This flow geometry was modeled as an axisymmetric cavity flow with a stationary surface representing the casing, and a rotating surface denoting the impeller. A 63 x 81-node mesh provided sufficient resolution in the regions of greatest flow variations and reduced the effects of numerical diffusion. The turbulence field was closed with the high Reynolds number form of the k-epsilon model supplemented with wall functions in the vicinity of the walls. Finally, a parametric study quantified the effects of through mass flow changes on this leakage flow.

Sindir, Munir M.↗
NASA NTRS1988

Element-by-element and implicit-explicit finite element formulations for computational fluid dynamics

Preconditioner algorithms to reduce the computational effort in FEM analyses of large-scale fluid-dynamics problems are presented. A general model problem is constructed on the basis of the convection-diffusion equation and the two-dimensional vorticity/stream-function formulation of the Navier-Stokes equations; this problem is then analyzed using element-by-element, implicit-explicit, and adaptive implicit-explicit approximation schemes. Numerical results for the two-dimensional advection and rigid-body rotation of a cosine hill, flow past a circular cylinder, and driven cavity flow are presented in extensive graphs and shown to be in good agreement with those obtained using implicit methods.

Tezduyar, T. E.↗
DOE OSTI2025

Learning and discovering multiple solutions using physics-informed neural networks with random initialization and deep ensemble

In this work we explore the capability of physics-informed neural networks (PINNs) to discover multiple solutions. Many real-world phenomena governed by nonlinear differential equations (DEs), such as fluid flow, exhibit multiple solutions under the same conditions, yet capturing this solution multiplicity remains a significant challenge. A key difficulty lies in providing appropriate initial conditions or guesses, as widely used time-marching schemes and Newton’s method are highly sensitive to these choices when solving complex computational problems. While machine learning models, particularly PINNs, have shown promise in solving DEs, their ability to capture multiple solutions remains underexplored. In this work, we propose a simple and practical approach using PINNs to learn and discover multiple solutions. We first demonstrate that PINNs, when combined with random initialization and deep ensemble method—originally developed for uncertainty quantification—can effectively uncover multiple solutions to nonlinear ordinary and partial DEs. Although training large ensembles of PINNs may appear computationally demanding, this can be done efficiently using vectorization techniques supported by modern deep learning frameworks, allowing many networks to be trained simultaneously. Our approach highlights the critical role of initialization in shaping solution diversity, addressing an often-overlooked aspect of machine learning for scientific computing. Furthermore, we propose utilizing PINN-generated solutions as initial conditions or initial guesses for conventional numerical solvers to enhance accuracy and efficiency in capturing multiple solutions. Extensive numerical experiments, including the Allen–Cahn equation and cavity flow, where our approach successfully identifies both stable and unstable solutions, validate the effectiveness of our method. These findings establish a general and efficient framework for addressing solution multiplicity in nonlinear DEs.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1989

Computations of three-dimensional steady and unsteady viscous incompressible flows

The INS3D family of computational fluid dynamics computer codes is presented. These codes are used to as tools in developing and assessing algorithms for solving the incompressible Navier-Stokes equations for steady-state and unsteady flow problems. This work involves applying the codes to real-world problems involving complex three-dimensional geometries. The algorithms utilized include the method of pseudocompressibility including both central and upwind differencing, several types of artificial dissipation schemes, approximate factorization, and an implicit line-relaxation scheme. These codes have been validated using a wide range of problems including flow over a backward-facing step, driven cavity flow, flow through various types of ducts, and steady and unsteady flow over a circular cylinder. Many diverse flow applications have been solved using these codes including parts of the Space Shuttle Main Engine, problems in naval hydrodynamics, low-speed aerodynamics, and biomedical fluid flows. The presentation details several of these, including the flow through a Space Shuttle Main Engine inducer, vortex shedding behind a circular cylinder, and flow through an artificial heart.

Kwak, Dochan↗
DOE OSTI2020

Hydrodynamic instabilities and heat transfer characteristics in the duct flow of a fluid in the supercritical thermodynamic regime

The behavior of fluids at supercritical thermodynamic conditions is inherently complex due to large variations in thermodynamic and transport properties. Recent numerical and experimental investigations illustrate ongoing interest for these fluids, especially supercritical CO 2 and supercritical water, for a variety of applications. For example, supercritical water reactors (SCWR) operate in this extreme condition of high-pressure and temperature, resulting in highly dynamic flow fields and unexpected heat transfer regimes. The potential heat transfer benefits in this regime are directly associated with the extreme variations in thermodynamic and transport properties, which occur at, and above, the critical point. This work characterizes the hydrodynamic instabilities that arise for fluids at supercritical thermodynamic conditions when buoyancy forces are significant. Two specific configurations are considered, a natural convection cavity flow, and a mixed convection, heated, horizontal channel flow. Natural convection flow in a cavity is a classical configuration with expected behavior below the critical point. This configuration aids in characterizing the effect of the variable properties in the supercritical thermodynamic regime. Further, limited studies in the existing literature have been conducted for low-Reynolds and intermediate-Rayleigh numbers, mixed-convection channel flows for supercritical water, which is the focus of the channel flow configuration. To investigate the thermally driven hydrodynamic instabilities in this regime, a high-order fully-implicit numerical method is used. Such strong variations in thermophysical properties (in particular, density) are difficult to simulate and an altogether compressible framework is needed. Therefore, the compressible Navier-Stokes equations are solved without any additional assumptions. The fully implicit, high-order in space and time, reconstructed discontinuous Galerkin method as implemented within the multi-physics code called ALE3D (Arbitrary Lagrangian and Eulerian in 2D and 3D), developed at Lawrence Livermore National Laboratory (LLNL), is used. This fully implicit, L-stable method accurately captures the compressible nature of the ow in the limit of very low Mach number. It has been widely accepted that above the critical point, only one phase is observed. However, recent research has indicated the existence of the distinct gas-like and liquid-like regions separated by the Widom line, the locus of the maxima of the specific heat. Along the Widom line, density decreases 6-fold, viscosity drops by a factor of 2, while specific heat spikes by an order of magnitude. These variations, specifically in density and viscosity, produce a thick pseudo-interface and flow dynamics behavior akin to film boiling. A pseudo-film at the heated wall of the cavity and the horizontal channel is observed where buoyancy forces induce mixing through the specific configurations. Further the local Rayleigh and Richardson numbers provide maps of the flow field and the buoyancy forces driving the microscopic mixing. In the first chapter, I describe a background of supercritical fluid and the various applications. The second chapter focuses on the mathematical model and numerical method used for simulations, where a description of the equation of state for supercritical water is described. The third chapter focuses on the natural convection cavity with a heated bottom wall. In this cavity a gas-like and a liquid-like flow within the supercritical thermodynamic regime are observed. The fourth chapter focuses on a forced convection, horizontal channel, distinguishing between the gas-like, liquid-like, and mixed flow regimes. Mixed convection flow, with the addition of gravitational forces in the horizontal channel show the influence of variable properties on the hydrodynamic development, heat transfer, and rising instabilities. The last chapter of this research focuses on characterizing the unstable hydrodynamics through time-averaging processes and analysis of the movement of energy through the developing plumes.

42 ENGINEERING↗
NASA NTRS1976

Experimental investigation of oscillations in flows over shallow cavities

Wind tunnel experiments were carried out with three axisymmetric models to study laminar axisymmetric flows over shallow cavities at low subsonic speeds. The first model had a hemispherical nose, the second an ogive-shape nose, and the third an elliptic nose. Constant-temperature hot-wire anemometry was used in measuring both mean and fluctuating quantities. Flow around the cavity was visualized by heating the first model. To study the effect of mass injection on cavity oscillations, air was injected circumferentially all along the base of the cavity. Major results are that the cavity depth has little effect on oscillations in shallow cavities except when the depth is of the order of the thickness of the cavity shear flow, that downstream corner is the key factor in inducing self-sustained oscillations in the cavity shear layer, and that the presence of a back face results in an integral relation between wave length of the propagating disturbances and the cavity width in each mode of cavity operation.

Sarohia, V.↗
NASA NTRS1991

On the anomaly of velocity-pressure decoupling in collocated mesh solutions

The use of various pressure correction algorithms originally developed for fully staggered meshes can yield a velocity-pressure decoupled solution for collocated meshes. The mechanism that causes velocity-pressure decoupling is identified. It is shown that the use of a partial differential equation for the incremental pressure eliminates such a mechanism and yields a velocity-pressure coupled solution. Example flows considered are a three dimensional lid-driven cavity flow and a laminar flow through a 90 deg bend square duct. Numerical results obtained using the collocated mesh are in good agreement with the measured data and other numerical results.

Kim, Sang-Wook↗
NASA NTRS1984

Application of improved numerical schemes

Two approaches which accelerate the solution of the steady state Navier-Stokes equations are discussed. The SIMPLER algorithm, a revised version of SIMPLE, provides a more accurate pressure field for each iteration through the momentum equations, thereby speeding convergence. PISO (Pressure Implicit Split Operator), performs a secondary correction of the velocity and pressure fields (after the typical pressure correction) which enhances convergence. Both schemes account for terms neglected in the SIMPLE approach, but do so in slightly different ways. Two dimensional driven cavity flow and flow over a step were calculated to examine the effect of geometry on the performance of these schemes. Computations were carried out on a series of progressively finer grids. The effect of relaxation number on convergence rate was analyzed, using results from SIMPLE as criteria for performance correlation. Results show: (1) the improved schemes promoted convergence by up to 60% for the driven cavity and 40% for flow over a step; (2) for the driven cavity problem, the efficiency of PISO and SIMPLER increased as the number of nodes increased; and (3) to ensure faster convergence, higher relaxation numbers must be applied.

Neely, G. H.↗
NASA NTRS1993

A coupled implicit method for chemical non-equilibrium flows at all speeds

The present time-accurate coupled-solution procedure addresses the chemical nonequilibrium Navier-Stokes equations over a wide Mach-number range uses, in conjunction with the strong conservation form of the governing equations, five unknown primitive variables. The numerical tests undertaken address steady convergent-divergent nozzle flows with air dissociation/recombination, dump combustor flows with n-pentane/air chemistry, and unsteady nonreacting cavity flows.

Shuen, Jian-Shun↗
NASA NTRS2012

Simulation of a Wall-Bounded Flow using a Hybrid LES/RAS Approach with Turbulence Recycling

Simulations of a supersonic recessed-cavity flow are performed using a hybrid large-eddy/ Reynolds-averaged simulation approach utilizing an inflow turbulence recycling procedure and hybridized inviscid flux scheme. Calorically perfect air enters the three-dimensional domain at a free stream Mach number of 2.92. Simulations are performed to assess grid sensitivity of the solution, efficacy of the turbulence recycling, and effect of the shock sensor used with the hybridized inviscid flux scheme. Analysis of the turbulent boundary layer upstream of the rearward-facing step for each case indicates excellent agreement with theoretical predictions. Mean velocity and pressure results are compared to Reynolds-averaged simulations and experimental data for each case, and these comparisons indicate good agreement on the finest grid. Simulations are repeated on a coarsened grid, and results indicate strong grid density sensitivity. The effect of turbulence recycling on the solution is illustrated by performing coarse grid simulations with and without inflow turbulence recycling. Two shock sensors, one of Ducros and one of Larsson, are assessed for use with the hybridized inviscid flux reconstruction scheme.

Quinlan, Jesse R.↗
NASA NTRS2004

Category 5: Sound Generation In Viscous Problems. Problem 2: Sound Generation By Flow Over a Cavity

The discrete frequency sound produced by the flow of air at low subsonic speeds over a deep cavity was investigated. A long aspect ratio rectangular cavity with a leading edge overhang that cut off of the cavity opening was placed flush with the top surface of a wind tunnel. The approach flow velocity was maintained at 50 m/s for the benchmark problem although results are also presented for other conditions. Boundary layer measurements conducted with a single element hotwire anemometer indicated that the boundary layer thickness just upstream of the cavity was equal to 17 mm. Sound pressure level measurements were made at three locations in the cavity: the center of the leading edge wall, the center of the cavity floor, and the center of the trailing edge wall. Three discrete tones were measured at all three locations with corresponding Strouhal numbers (based on cavity opening length and approach flow velocity) equal to 0.24, 0.26, and 0.41. The amplitudes of each tone were approximately equal at each measurement location in the cavity. Measurements made at other approach flow conditions indicated that the approach flow velocity and the boundary layer thickness affected the frequency characteristics of the discrete tones.

Henderson, Brenda S.↗
NASA NTRS1992

A time-accurate algorithm for chemical non-equilibrium viscous flows at all speeds

A time-accurate, coupled solution procedure is described for the chemical nonequilibrium Navier-Stokes equations over a wide range of Mach numbers. This method employs the strong conservation form of the governing equations, but uses primitive variables as unknowns. Real gas properties and equilibrium chemistry are considered. Numerical tests include steady convergent-divergent nozzle flows with air dissociation/recombination chemistry, dump combustor flows with n-pentane-air chemistry, nonreacting flow in a model double annular combustor, and nonreacting unsteady driven cavity flows. Numerical results for both the steady and unsteady flows demonstrate the efficiency and robustness of the present algorithm for Mach numbers ranging from the incompressible limit to supersonic speeds.

Shuen, J.-S.↗
NASA NTRS1971

Experimental study of the effects of injection conditions on the flow in cylindrical and spherical chambers.

Fluid mechanics experiments were performed in cylindrical and spherical chambers to evaluate the simulated-fuel containment resulting from various injection geometry and inlet flow conditions for application to the open-cycle GNR. A preliminary study in the cylindrical chamber was directed toward developing inlet flow conditions which minimize mixing between the simulated fuel and propellant. Gas concentration measurements were obtained at several outer-stream to inner-stream weight flow and density ratios for the best inlet configuration tested in the preliminary study. The spherical cavity flow study was conducted to evaluate techniques for injecting simulated-fuel and propellant into a cavity.

Johnson, B. V.↗
NASA NTRS1981

Interactive method for computation of viscous flow with recirculation

An interactive method is proposed for the solution of two-dimensional, laminar flow fields with identifiable regions of recirculation, such as the shear-layer-driven cavity flow. The method treats the flow field as composed of two regions, with an appropriate mathematical model adopted for each region. The shear layer is computed by the compressible boundary layer equations, and the slowly recirculating flow by the incompressible Navier-Stokes equations. The flow field is solved iteratively by matching the local solutions in the two regions. For this purpose a new matching method utilizing an overlap between the two computational regions is developed, and shown to be most satisfactory. Matching of the two velocity components, as well as the change in velocity with respect to depth is amply accomplished using the present approach, and the stagnation points corresponding to separation and reattachment of the dividing streamline are computed as part of the interactive solution. The interactive method is applied to the test problem of a shear layer driven cavity. The computational results are used to show the validity and applicability of the present approach.

Brandeis, J.↗
NASA NTRS2004

Wind Tunnel Test Results for Gas Flows Inside Axisymmetric Cavities on Cylindric Bodies with Nose Cones

Experimental test results of air flow inside and at the cylindrical cavity located on axisymmetric body are presented. These tests were conducted in the wind tunnel A-7 of Institute of Mechanics at Moscow State University. Pressure distribution along the cavities and optical measurements were obtained. Dependence of these characteristics of length of a cavity in the range: L/D = 0.5 - 14 and free stream Mach in the range: M(sub infinity) = 0.6 - 3.0 was determined. Flow structure inside the cavity, cause of flow regime change, separation zones geometry and others were studied. In particular, the flow modes of with open and closed separation zones are determined.

Shvets, A. L.↗
NASA NTRS2000

A Reduced Order Model of the Linearized Incompressible Navier-Strokes Equations for the Sensor/Actuator Placement Problem

A reduced order modeling approach of the Navier-Stokes equations is presented for the design of a distributed optimal feedback kernel. This approach is based oil a Krylov subspace method where significant modes of the flow are captured in the model This model is then used in all optimal feedback control design where sensing and actuation is performed oil tile entire flow field. This control design approach yields all optimal feedback kernel which provides insight into the placement of sensors and actuators in the flow field. As all evaluation of this approach, a two-dimensional shear layer and driven cavity flow are investigated.

Allan, Brian G.↗