Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “bulk techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Physical and hydraulic properties of baked ceramic aggregates used for plant growth medium

Baked ceramic aggregates (fritted clay, arcillite) have been used for plant research both on the ground and in microgravity. Optimal control of water and air within the root zone in any gravity environment depends on physical and hydraulic properties of the aggregate, which were evaluated for 0.25-1-mm and 1-2-mm particle size distributions. The maximum bulk densities obtained by any packing technique were 0.68 and 0.64 g cm-3 for 0.25-1-mm and 1-2-mm particles, respectively. Wettable porosity obtained by infiltration with water was approximately 65%, substantially lower than total porosity of approximately 74%. Aggregate of both particle sizes exhibited a bimodal pore size distribution consisting of inter-aggregate macropores and intra-aggregate micropores, with the transition from macro- to microporosity beginning at volumetric water content of approximately 36% to 39%. For inter-aggregate water contents that support optimal plant growth there is 45% change in water content that occurs over a relatively small matric suction range of 0-20 cm H2O for 0.25-1-mm and 0 to -10 cm H2O for 1-2-mm aggregate. Hysteresis is substantial between draining and wetting aggregate, which results in as much as a approximately 10% to 20% difference in volumetric water content for a given matric potential. Hydraulic conductivity was approximately an order of magnitude higher for 1-2-mm than for 0.25-1-mm aggregate until significant drainage of the inter-aggregate pore space occurred. The large change in water content for a relatively small change in matric potential suggests that significant differences in water retention may be observed in microgravity as compared to earth.

NASA Center JSC↗
NASA NTRS1977

C-MOS bulk metal design handbook

The LSI standard cell array technique was used in the fabrication of more than 20 CMOS custom arrays. This technique consists of a series of computer programs and design automation techniques referred to as the Computer Aided Design And Test (CADAT) system that automatically translate a partitioned logic diagram into a set of instructions for driving an automatic plotter which generates precision mask artwork for complex LSI arrays of CMOS standard cells. The standard cell concept for producing LSI arrays begins with the design, layout, and validation of a group of custom circuits called standard cells. Once validated, these cells are given identification or pattern numbers and are permanently stored. To use one of these cells in a logic design, the user calls for the desired cell by pattern number. The Place, Route in Two Dimension (PR2D) computer program is then used to automatically generate the metalization and/or tunnels to interconnect the standard cells into the required function. Data sheets that describe the function, artwork, and performance of each of the standard cells, the general procedure for implementation of logic in CMOS standard cells, and additional detailed design information are presented.

Edge, T. M.↗
NASA NTRS1982

Comparison of NDE techniques for sintered-SiC components

High frequency, bulk-wave ultrasonics detected defects in manufactured SiC components. In addition, gas-turbine blades and vanes were examined by scanning laser acoustic microscopy (SLAM). Comparative results obtained on simple shapes such as disks and bars by microfocus X-ray radiography, ultrasonics, scanning photoacoustic spectroscopy, and SLAM are discussed.

Srinivasan, M.↗
NASA NTRS1975

Boron Arsenide and Boron Phosphide for High Temperature and Luminescent Devices

The crystal growth of boron arsenide and boron phosphide in the form of bulk crystals and epitaxial layers on suitable substrates is discussed. The physical, chemical, and electrical properties of the crystals and epitaxial layers are examined. Bulk crystals of boron arsenide were prepared by the chemical transport technique, and their carrier concentration and Hall mobility were measured. The growth of boron arsenide crystals from high temperature solutions was attempted without success. Bulk crystals of boron phosphide were also prepared by chemical transport and solution growth techniques. Techniques required for the fabrication of boron phosphide devices such as junction shaping, diffusion, and contact formation were investigated. Alloying techniques were developed for the formation of low-resistance ohmic contacts to boron phosphide. Four types of boron phosphide devices were fabricated: (1) metal-insulator-boron phosphide structures, (2) Schottky barriers; (3) boron phosphide-silicon carbide heterojunctions; and (4) p-n homojunctions. Easily visible red electroluminescence was observed from both epitaxial and solution grown p-n junctions.

Chu, T. L.↗
NASA NTRS2020

Exploratory Experiments to Probe the Effect of Bulk Density and Porosity on The Morphology and Ejecta Kinematics of Impact Craters

The morphometry of relatively small impact craters are influenced by the physical properties of the target. To investigate the control of bulk density and porosity on the crater-formation processing the gravity regime, we conducted a series of impact experiments, varying each these target parameters while holding the other constant. Three different sands were used to construct cohesionless targets: quartz (0.4-0.8 mm), garnet (0.425-1.0 mm), and alumina (0.297-0.71mm), representing a range of intrinsic grain densities from 2.65 to 4.02 g cm-3. High-porosity targets were constructed by carefully pouring the sand into the center of a cylindrical PVC target bucket (inner diameter 26.2 cm, height 12 cm) and allowing it to fill the bucket at the angle of repose before being leveled flat at the top of the bucket. Low-porosity targets were obtained by pluviation of the granular material through a 1 mm sieve that was set directly above the target bucket. With the disparate intrinsic densities of the sand in combination with the variations of the packing technique, we attained differences in the bulk-target density of up to 32%while keeping porosity constant. The impact experiments were conducted with the vertical gun in the Experimental Impact Laboratory at NASA Johnson Space Center; using 3/16” (4.76 mm) diameter aluminum projectiles launched at1.55 ± 0.03 km s-1. The ejecta were observed using the laser-based Ejection Velocity Measurement System, providing data on launch positions and velocities of ejected particles. Submillimeter topographic data of the resulting craters were collected after each experiment with a NextEngine 3D scanner. Regardless of target material or density, all craters exhibited a simple bowl shape, but a trend of increasing depth-diameter ratio with increasing target porosity is observed across the entire experimental suite. Despite these morphometric differences, ejecta launch angles and speeds remain remarkably similar amongst all of the target configurations.

impact cratering↗
NASA NTRS1973

Inventory of forest and rangeland and detection of forest stress

The author has identified the following significant results. Three small scales of CIR photography were interpreted to determine the number of bark beetle-killed trees detected in each of six spot size categories. A procedure was developed to predict the probability of detecting spots in each spot size category and in turn to estimate the number of infestations and dead trees even on the smallest scale. Statistical tests of the data indicated that the linear model did not fit the data and that other models should be tested. As a result of daily monitoring of Black Hills radiometric instruments it was possible to show the spectral energy relationships in the ponderosa pine ecosystems over time. These data have been helpful for comparison with radiance signatures extracted from ERTS-1 bulk 70mm using precision microdensitometry. Effects of atmospheric interference were shown by a 30 percent increase in scene radiance on channel 4 of the satellite imagery. A calibration and scaling technique was developed and tested to enable interpretation of ERTS-1 bulk and precision data for the Atlanta test site. The technique includes calibration of a photographic copy system for the I2S image combiner and the production of scaled overlays of grid coordinate systems, study area locations, and outline maps of county boundaries.

Heller, R. C.↗
NASA NTRS2017

Exploring the Utilization of Low-Pressure, Piston-Cylinder Experiments to Determine the Bulk Compositions of Finite, Precious Materials

Determining the bulk composition of precious materials with a finite mass (e.g., meteorite samples) is extremely important in the fields of Earth and Planetary Science. From meteorite studies we are able to place constraints on large scale planetary processes like global differentiation and subsequent volcanism, as well as smaller scale processes like crystallization in a magma chamber or sedimentary compaction at the surface. However, with meteorite samples in particular, far too often we are limited by how precious the sample is as well as its limited mass. In this study, we have utilized aliquots of samples previously studied for toxicological hazards, including both the fresh samples (lunar mare basalt NWA 4734, lunar regolith breccia NWA 7611, martian basalt Tissint, martian regolith breccia NWA 7034, a vestian basalt Berthoud, a vestian regolith breccia NWA 2060, and a terrestrial mid-ocean ridge basalt (MORB)), and those that underwent iron leaching (Tissint, NWA 7034, NWA 4734, MORB). With these small masses of material, we performed low pressure (approx. 0.75 GPa), high temperature (greater than 1600 degrees Celsius) melting experiments. Each sample was analyzed using a JEOL 8530F electron microprobe to determine the bulk composition of the materials that were previously examined. When available, the results of our microprobe data were compared with bulk rock compositions in the literature. The results of this study show that with this technique, only approx. 50 mg of sample is required to accurately determine the bulk composition of the materials of interest.

Vander Kaaden, K. E.↗
NASA NTRS1972

An observation of the Gulf Stream surface front structure by ship, aircraft, and satellite.

Evaluation of observations of surface temperature and salinity along the western edge of the Gulf Stream made from a ship and of concurrent temperature observations obtained by instrumented aircraft at six altitudes. The major feature along a five-kilometer line normal to the Stream's edge is a temperature gradient of about 0.75 C/kilometer within which are embedded two abrupt temperature increases of about 1.5 C. Temperature variations were compensated by salinity variations, yielding nearly constant density through the frontal zone; a sharp lateral current shear was associated with the thermohaline mixing region between the steps. The attenuation of surface temperature measured by the airborne radiometer was compared with a theoretical model. The analysis supports the view that a two-part correction technique is required: one part for bulk-skin temperature differences, and another for atmospheric attenuation of sea surface emission due to the mass and temperature of interfering gases.

Maul, G. A.↗
NASA NTRS1973

Dynamics of distribution and density of phreatophytes and other arid-land plant communities

The author has identified the following significant results. Six ERTS-1 images of the Tucson area, Arizona were analyzed to detect seasonal flushes of plant growth. Paired MSS-6 and MSS-5 bulk images were analyzed, using a ratioing technique, on the Electronic Satellite Image Analysis Console at Stanford Research Institute. Because of unique phenology, desert areas, covered only briefly by dense growths of ephemeral plants, are readily discerned. Grassland, evergreen forest, and riparian communities are also uniquely defined by their phenologies. Relatively sterile areas with little or no plant growth are easily discerned as are areas with varying degrees of plant productivity. The ratioing procedure detects plant coverage in excess of a threshold lying between 25% and 50%. The method is flexible and other coverage thresholds can be used.

Turner, R. M.↗
NASA NTRS1977

Application of the SEM to the measurement of solar cell parameters

Techniques are described which make use of the SEM to measure the minority carrier diffusion length and the metallurgical junction depth in silicon solar cells. The former technique permits the measurement of the true bulk diffusion length through the application of highly doped field layers to the back surfaces of the cells being investigated. It is shown that the secondary emission contrast observed in the SEM on a reverse-biased diode can depict the location of the metallurgical junction if the diode has been prepared with the proper beveled geometry. The SEM provides the required contrast and the option of high magnification, permitting the measurement of extremely shallow junction depths.

Weizer, V. G.↗
NASA NTRS1978

A neon-E rich phase in Orgueil - Results of stepwise heating experiments

A Ne-E rich phase was separated from the Orgeuil carbonaceous chondrite. He and Ne were analyzed in this phase and in an Orgueil residual bulk silicate sample using the stepwise heating technique. Ne-E was found to be released from the Ne-E rich phase at temperatures as low as 500 C; however, gas richest in Ne-E is observed at the highest temperatures (1230 C). The following limits for the isotopic composition of Ne-E were obtained: Ne-20/Ne-22 less than 1.52; Ne-21/Ne-22 less than 0.0244.

Eberhardt, P.↗
NASA NTRS1981

The Retarding Ion Mass Spectrometer on Dynamics Explorer-A

The thermal component of the magnetospheric plasma plays a key role in magnetosphere-ionosphere coupling processes, acting as a strong influence on ionospheric structure at low altitudes and as a source and modifier of the hotter plasma population at high altitudes. The Retarding Ion Mass Spectrometer (RIMS) instrument on Dynamics Explorer-A is designed to measure this important thermal plasma component. Using a combination of retarding potential analysis and magnetic ion mass spectrometer techniques, the RIMS instrument will measure the bulk plasma parameters of ion density (0.1 to 1,000,000 ions/cu cm), temperature (0-45 eV), and bulk flow (greater than 0.5 km/sec) in the inner plasmasphere and ionosphere, and the specific ion pitch angle and energy spectral characteristics in the outer plasmasphere and plasma trough for a mass range of 1-32 amu. The energy and mass spectral step sequences, as well as the multiplexing of the resultant data, can be tailored to accomplish a variety of thermal ion measurements throughout the inner magnetosphere.

Chappell, C. R.↗
NASA NTRS1984

Overview of Bulk Silicon Crystal Growth

The Czochralski and float-zone techniques are reviewed and the consequences of high growth rates in the growth of electronic grade silicon are examined. Impurity segregation coefficients are defined.

Source record↗
NASA NTRS1982

Photovoltaic characteristics of diffused P/+N bulk GaAs solar cells

The photovoltaic characteristics of P(+)N junction solar cells fabricated on bulk GaAs by an open tube diffusion technique are described in this paper.Spectral response measurements were analyzed in detail and compared to a computer simulation in order to determine important material parameters. It is projected that proper optimization of the cell parameters can increase the efficiency of the cells from 12.2 percent to close to 20 percent.

Borrego, J. M.↗
NASA NTRS1984

Diffused junction p(+)-n solar cells in bulk GaAs. II - Device characterization and modelling

The photovoltaic characteristics of p(+)-n junction solar cells fabricated on bulk GaAs by an open tube diffusion technique are presented in detail. Quantum efficiency measurements were analyzed and compared to computer simulations of the cell structure in order to determine material parameters such as diffusion length, surface recombination velocity and junction depth. From the results obtained it is projected that proper optimization of the cell parameters can increase the efficiency of the cells to close to 20 percent.

Keeney, R.↗
NASA NTRS1985

Directed-energy process technology efforts

A summary of directed-energy process technology for solar cells was presented. This technology is defined as directing energy or mass to specific areas on solar cells to produce a desired effect in contrast to exposing a cell to a thermal or mass flow environment. Some of these second generation processing techniques are: ion implantation; microwave-enhanced chemical vapor deposition; rapid thermal processing; and the use of lasers for cutting, assisting in metallization, assisting in deposition, and drive-in of liquid dopants. Advantages of directed energy techniques are: surface heating resulting in the bulk of the cell material being cooler and unchanged; better process control yields; better junction profiles, junction depths, and metal sintering; lower energy consumption during processing and smaller factory space requirements. These advantages should result in higher-efficiency cells at lower costs. The results of the numerous contracted efforts were presented as well as the application potentials of these new technologies.

Alexander, P.↗
NASA NTRS2003

Preparation and Characterization of Space Durable Polymer Nanocomposite Films from Functionalized Carbon Nanotubes

Low color, flexible, space durable polyimide films with inherent, robust electrical conductivity have been under investigation as part of a continuing materials development activity for future NASA space missions involving Gossamer structures. Electrical conductivity is needed in these films to dissipate electrostatic charge build-up that occurs due to the orbital environment. One method of imparting conductivity is through the use of single walled carbon nanotubes (SWNTs). However, the incompatibility and insolubility of the SWNTs severely hampers their dispersion in polymeric matrices. In an attempt to improve their dispersability, SWNTs were functionalized by the reaction with an alkyl hydrazone. After this functionalization, the SWNTs were soluble in select solvents and dispersed more readily in the polymer matrix. The functionalized SWNTs were characterized by Raman spectroscopy and thermogravimetric analysis (TGA). The functionalized nanotubes were dispersed in the bulk of the films using a solution technique. The functionalized nanotubes were also applied to the surface of polyimide films using a spray coating technique. The resultant polyimide nanocomposite films were evaluated for nanotube dispersion, electrical conductivity, mechanical, and optical properties and compared with previously prepared polyimide-SWNT samples to assess the effects of SWNT functionalization.

Delozier, D. M.↗
NASA NTRS2007

Evaluation of Bulk Charging in Geostationary Transfer Orbit and Earth Escape Trajectories Using the Numit 1-D Charging Model

The NUMIT 1-dimensional bulk charging model is used as a screening to ol for evaluating time-dependent bulk internal or deep dielectric) ch arging of dielectrics exposed to penetrating electron environments. T he code is modified to accept time dependent electron flux time serie s along satellite orbits for the electron environment inputs instead of using the static electron flux environment input originally used b y the code and widely adopted in bulk charging models. Application of the screening technique ts demonstrated for three cases of spacecraf t exposure within the Earth's radiation belts including a geostationa ry transfer orbit and an Earth-Moon transit trajectory for a range of orbit inclinations. Electric fields and charge densities are compute d for dielectric materials with varying electrical properties exposed to relativistic electron environments along the orbits. Our objectiv e is to demonstrate a preliminary application of the time-dependent e nvironments input to the NUMIT code for evaluating charging risks to exposed dielectrics used on spacecraft when exposed to the Earth's ra diation belts. The results demonstrate that the NUMIT electric field values in GTO orbits with multiple encounters with the Earth's radiat ion belts are consistent with previous studies of charging in GTO orb its and that potential threat conditions for electrostatic discharge exist on lunar transit trajectories depending on the electrical proper ties of the materials exposed to the radiation environment.

Minow, Joseph I.↗