Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “bubbly flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Using X-ray radiography to study oxygen flow in a proton exchange membrane electrolyzer operating under balanced pressure conditions

Of the various water electrolyzer technologies, the proton exchange membrane electrolyzer (PEMWE) is one of the best solutions for producing clean hydrogen without releasing CO 2 . In order to allow for widespread use of clean hydrogen, it is necessary to decrease its cost, which is intrinsically related to system operation. Current PEMWE plants operate in differential mode, directly pressurizing hydrogen and benefiting from thermodynamic compression, which increases overall system efficiency. However, high differential pressure above 30 bar can cause membrane stress, resulting in membrane creeping and failure. Pressurizing the water and operating at balanced pressure allows hydrogen to be produced at higher pressures while preserving the integrity of the membrane and porous layers. Nevertheless, the impact of pressurizing water on PEMWE performance must be better understood to maximize performance under balanced pressure conditions. Here, this study examined the impact of water pressure on two-phase flow. A high-pressure electrolyzer setup was developed to perform operando X-ray radiography and examine oxygen transport with high temporal resolution. The imaging segmentation process, developed to capture bubble properties in the channel, was applied to a specific experiment. The results clearly showed that as pressure increased up to 30 bars, the initial bubbly flow transitioned to slug flow, which led to channel saturation with oxygen. This work demonstrates that two-phase flow in an electrolyzer can be studied using X-ray radiography, which has the advantages of fast measurements and the ability to probe dense materials, such as those required for pressurized electrolyzers.

Balanced high pressure operation↗

Chemical hydrodynamics of a downward microbubble flow for intensification of gas‐fed bioreactors

Bioreactors are of interest for value‐upgrading of stranded or waste industrial gases. Reactor intensification requires development of low cost bioreactors with fast gas–liquid mass transfer rate. Here we assess published reactor technology in comparison with a novel downward bubble flow created by a micro‐jet array. Compared to known technology, the advanced design achieves higher volumetric gas transfer efficiency (k L a per power density) and can operate at higher k L a. We measure the effect of four reactor heights (height‐to‐diameter ratios of 12, 9, 6, and 3) on the gas transfer coefficient k L , total interfacial area a, liquid residence time distribution, energy consumption, and turbulent hydrodynamics. Leading models for predicting k L and a are appraised with experimental data. The results show k L is governed by “entrance effects” due to Higbie penetration dominate at short distances below the micro‐jet array, while turbulence dominates at intermediate distances, and finally terminal rise velocity dominates at large distances. © 2017 American Institute of Chemical Engineers AIChE J , 64: 1399–1411, 2018

Ansari, Manizheh↗

BACKPRESSURE TESTING OF ROTARY MICROFILTER DISKS

The Savannah River National Laboratory (SRNL), under the Department of Energy (DOE) Office of Environmental Management (EM), is modifying and testing the SpinTek{trademark} rotary microfilter (RMF) for radioactive filtration service in the Department of Energy (DOE) complex. The RMF has been shown to improve filtration throughput when compared to other conventional methods such as cross-flow filtration. A concern with the RMF was that backpressure, or reverse flow through the disk, would damage the filter membranes. Reverse flow might happen as a result of an inadvertent valve alignment during flushing. Testing was completed in the Engineering Development Laboratory (EDL) located in SRNL to study the physical effects of backpressure as well as to determine the maximum allowable back-pressure for RMF disks. The RMF disks tested at the EDL were manufactured by SpinTek{trademark} Filtration and used a Pall Corporation PMM050 filter membrane (0.5 micron nominal pore size) made from 316L stainless steel. Early versions of the RMF disks were made from synthetic materials that were incompatible with caustic solutions and radioactive service as well as being susceptible to delaminating when subjected to backpressure. Figure 1-1 shows the essential components of the RMF; 3 rotating disks and 3 stationary turbulence promoters (or shear elements) are shown. Figure 1-2 show the assembly view of a 25 disk RMF proposed for use at the Savannah River Site (SRS) and at the Hanford Facility. The purpose of the testing discussed in this report was to determine the allowable backpressure for RMF disks as well as study the physical effects of backpressure on RMF disks made with the Pall PMM050 membrane. This was accomplished by pressurizing the disks in the reverse flow direction (backpressure) until the test limit was reached or until membrane failure occurred. Backpressure was applied to the disks with air while submerged in deionized (DI) water. This method provided a visual representation of membrane integrity via bubble flow patterns. Membrane failure was defined as the inability to filter effectively at the nominal filter pore size. Effective filtration was determined by turbidity measurements of filtrate that was produced by applying forward-pressure to the disks while submerged in a representative simulant. The representative simulant was Tank 8F simulated sludge produced for SRNL by Optima Chemical. Two disks were tested. Disk 1 was tested primarily to determine approximate levels of backpressure where membrane failure occurred. These levels were then used to define the strategy for testing the Disk 2; a strategy that would better define and quantify the mode of failure.

36 MATERIALS SCIENCE↗

Prediction of performance of two-phase flow nozzle and liquid metal magnetohydrodynamic (LMMHD) generator for no slip condition

Two-phase LMMHD energy conversion systems have potentially significant advantages over conventional systems such as higher thermal efficiency and substantial simplicity with lower capital and maintenance costs. Maintenance of low velocity slip is of importance for achieving high generator efficiency. A bubbly flow pattern ensures very low velocity slip. The full governing equations have been written out, and a computer prediction code has been developed to analyze performance of a two-phase flow LMMHD generator and nozzle under conditions of no slip. Three different shapes of a LMMHD generator have been investigated. Electrical power outputs are in the 20 kW range. Generator efficiency exceeds 71 percent at an average void fraction of about 70 percent. This is an appreciable performance for a short generator without insulating vanes for minimizing electrical losses in the end regions.

Fabris, G.↗

Multi-scale thermalhydraulic analyses performed in Nuresim and Nurisp projects

The NURESIM and NURISP successive projects of the 6. and 7. European Framework Programs joined the efforts of 21 partners for developing and validating a reference multi-physics and multi-scale platform for reactor simulation. The platform includes system codes, component codes, and also CFD or CMFD simulation tools. Fine scale CFD simulations are useful for a better understanding of physical processes, for the prediction of small scale geometrical effects and for solving problems that require a fine space and/or time resolution. Many important safety issues usually treated at the system scale may now benefit from investigations at a CFD scale. The Pressurized Thermal Shock is investigated using several simulation scales including Direct Numerical Simulation, Large Eddy Simulation, Very Large Eddy Simulation and RANS approaches. At the end a coupling of system code and CFD is applied. Condensation Induced Water-Hammer was also investigated at both CFD and 1-D scale. Boiling flow in a reactor core up to Departure from Nucleate Boiling or Dry-Out is investigated at scales much smaller than the classical subchannel analysis codes. DNS was used to investigate very local processes whereas CFD in both RANS and LES was used to simulate bubbly flow and Euler-Lagrange simulations were used for annular mist flow investigations. Loss of Coolant Accidents are usually treated by system codes. Some related issues are now revisited at the CFD scale. In each case the progress of the analysis is summarized and the benefit of the multi-scale approach is shown. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Effects of surface perturbations on the asymmetric vortex flow over a slender body

An experimental investigation of the effects of surface perturbations on the asymmetric flow past a slender body has been conducted for laminar flow conditions. Beads with diameters ranging from 3/32 to 12/32 in. were attached near the apex of a cone/cylinder model having a base diameter of 3.5 in. and a cone semiapex angle of 9 deg at an angle of attack of 40 deg in an attempt to alter the sense of the asymmetric vortex flow pattern. Circumferential position as well as longitudinal location were varied to determine the most effective bead position. Whether or not the beads were effective in controlling the magnitude and direction of the vortex asymmetries was determined by 3 circumferential rows of pressure taps and by a helium-bubble flow visualization technique. The most effective circumferential position was found to be approximately 140 deg from the windward ray. While holding this circumferential position constant, the effect of bead size at three stations further along the body was also investigated. It was found that the size of the bead necessary to reverse the asymmetry increased more rapidly than the growth in cylinder radius. In general, these results indicate that discrete geometric imperfections on a body's surface can force asymmetry in a given direction if they are sufficiently large relative to the local radius.

Moskovitz, Cary A.↗

Three-Dimensional Bubble Fluidics in Architected Porous Media

Gas bubble flows in porous media often exhibit complex and seemingly unpredictable behaviors that are difficult to control. This lack of control limits the ability to design effective devices which manage multiphase flows. Here, we show how the design of 3D printed pores can deterministically control the flow path of an injected gas stream. Open cell structures can be designed to shape the gas/liquid interface with fidelity to control how the two phases are distributed throughout a porous material. The distributed gas volume is free to interact physically and chemically with the surrounding liquid phase, an effect we exploit to create a logical control gate to redirect flows within a lattice. This also allows us to design architectures for reactive capture and aerating bioreactors, resulting in patterned boundaries which can make more effective use of the liquid and gas reagents.

3D microfluidics↗

Modeling of Two-Phase Flow around Spacers with Mixing Vanes in Reactor Rod-Bundles

Reactor fuel rod bundles experience complex two-phase flow patterns that are governed by multiple interacting phenomena. Proper understand of the underlying flow hydrodynamics can point to potential hotspots within nuclear reactors. The structural supports, called spacer grids, have mixing vanes fixed to the trailing edges to enhance mixing and swirl within the flow. This is an added phenomenon that makes the flows even more complicated to model. As reactors can experience boiling conditions, it is important to understand how the spacer geometry affects local velocity and phase distributions in these geometries. This work represents a continuation of a study that has been focused on developing, testing, and validation of a consistent multidimensional model of dispersed bubbly flow along PWR coolant channels,. The proposed model has been implemented in the NPHASE-CMFD code the results of computer simulations have been compared to experimental results of Yloenen. One of the objectives of the current study has been to examine the effects of selected recent modeling improvements at RPI in NPHASE-CMFD as a part of the continuing model development and validation efforts. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Condensation of Forced Convection Two-Phase Flow in a Miniature Tube

A physical/mathematical model of annular film condensation at the inlet of a miniature tube has been developed. In the model, the liquid flow is coupled with the vapor flow along the liquid-vapor interface through the interfacial temperature, heat flux, shear stress, and pressure jump conditions due to surface tension effects. The model predicts the shape of the liquid-vapor interface along the condenser and leads to the conclusion that there is complete condensation at a certain distance from the condenser inlet. The numerical results show that complete condensation of the incoming vapor is possible at comparatively low heat loads and that this is a special case of a more general condensation regime with two-phase bubbly flow downstream of the initial annular film condensation region. Observations from the flow visualization experiment confirm the existence and qualitative features of annular film condensation leading to the complete condensation phenomenon in a small diameter (3.25 mm) circular tube condenser.

Begg, E.↗

CFD Study of Full-Scale Aerobic Bioreactors: Evaluation of Dynamic O2 Distribution, Gas-Liquid Mass Transfer and Reaction

If advanced biofuels are to measurably displace fossil fuels in the near term, they will have to operate at levels of scale, efficiency, and margin unprecedented in the current biotech industry. For aerobically-grown products in particular, scale-up is complex and the practical size, cost, and operability of extremely large reactors is not well understood. Put simply, the problem of how to attain fuel-class production scales comes down to cost-effective delivery of oxygen at high mass transfer rates and low capital and operating costs. To that end, very large reactor vessels (>500 m3) are proposed in order to achieve favorable economies of scale. Additionally, techno-economic evaluation indicates that bubble-column reactors are more cost-effective than stirred-tank reactors in many low-viscosity cultures. In order to advance the design of extremely large aerobic bioreactors, we have performed computational fluid dynamics (CFD) simulations of bubble-column reactors. A multiphase Euler-Euler model is used to explicitly account for the spatial distribution of air (i.e., gas bubbles) in the reactor. Expanding on the existing bioreactor CFD literature (typically focused on the hydrodynamics of bubbly flows), our simulations include interphase mass transfer of oxygen and a simple phenomenological reaction representing the uptake and consumption of dissolved oxygen by submerged cells. The simulations reproduce the expected flow profiles, with net upward flow in the center of column and downward flow near the wall. At high simulated oxygen uptake rates (OUR), oxygen-depleted regions can be observed in the reactor. By increasing the gas flow to enhance mixing and eliminate depleted areas, a maximum oxygen transfer (OTR) rate is obtained as a function of superficial velocity. These insights regarding minimum superficial velocity and maximum reactor size are incorporated into NREL's larger techno-economic models to supplement standard reactor design equations.

09 BIOMASS FUELS↗

Stereo Imaging Velocimetry

Stereo imaging velocimetry (SIV) will permit the collection of quantitative, three-dimensional flow data from any optically transparent fluid that can be seeded with tracer particles. This includes such diverse experiments as the study of multiphase flow, bubble nucleation and migration, pool combustion, and crystal growth. This technique will be useful to the microgravity science community as our investigations of fluid behavior in reduced-gravity environments enhance our knowledge of heat transfer, surface tension, concentration-gradient-driven anomalies, and residual effects from g-jitter. In its proposed configuration, the NASA Lewis Research Center's Stereo Imaging Velocimeter will consist of at least two charged coupled device (CCD) cameras, oriented at some relative angle with respect to each other. The cameras will observe a fluid experiment that has been seeded with tracer particles that are neutrally buoyant to permit accurate flow tracking. Except for the tracer particles, this measurement technique will be nonintrusive. Velocity accuracies will be on the order of 1 to 5 percent of full field. Each camera will make a two-dimensional record of the motion of the seed particles in the observation volume. Three-dimensional data will be obtained by computationally combining the two-dimensional information.

Source record↗

Uncertainty Quantification for Multiphase Computational Fluid Dynamics Closure Relations with a Physics-Informed Bayesian Approach

Multiphase Computational Fluid Dynamics (MCFD) based on the two-fluid model is considered a promising tool to model complex two-phase flow systems. MCFD simulation can predict local flow features without resolving interfacial information. As a result, the MCFD solver relies on closure relations to describe the interaction between the two phases. Those empirical or semi-mechanistic closure relations constitute a major source of uncertainty for MCFD predictions. In this paper, we leverage a physics-informed uncertainty quantification (UQ) approach to inversely quantify the closure relations’ model form uncertainty in a physically consistent manner. This proposed approach considers the model form uncertainty terms as stochastic fields that are additive to the closure relation outputs. Combining dimensionality reduction and Gaussian processes, the posterior distribution of the stochastic fields can be effectively quantified within the Bayesian framework with the support of experimental measurements. As this UQ approach is fully integrated into the MCFD solving process, the physical constraints of the system can be naturally preserved in the UQ results. Here, in a case study of adiabatic bubbly flow, we demonstrate that this UQ approach can quantify the model form uncertainty of the MCFD interfacial force closure relations, thus effectively improving the simulation results with relatively sparse data support.

42 ENGINEERING↗

Modeling and simulation challenges pursued by the Consortium for Advanced Simulation of Light Water Reactors (CASL)

The Consortium for the Advanced Simulation of Light Water Reactors (CASL), the first Energy Innovation Hub of the Department of Energy, was established in 2010 with the goal of providing modeling and simulation (M&S) capabilities that support and accelerate the improvement of nuclear energy's economic competitiveness and the reduction of spent nuclear fuel volume per unit energy, and all while assuring nuclear safety. To accomplish this requires advances in M&S capabilities in radiation transport, thermal-hydraulics, fuel performance and corrosion chemistry. To focus CASL's R&D, industry challenge problems have been defined, which equate with long standing issues of the nuclear power industry that M&S can assist in addressing. To date CASL has developed a multi-physics “core simulator” based upon pin-resolved radiation transport and subchannel (within fuel assembly) thermal-hydraulics, capitalizing on the capabilities of high performance computing. CASL's fuel performance M&S capability can also be optionally integrated into the core simulator, yielding a coupled multi-physics capability with untapped predictive potential. Material models have been developed to enhance predictive capabilities of fuel clad creep and growth, along with deeper understanding of zirconium alloy clad oxidation and hydrogen pickup. Understanding of corrosion chemistry (e.g., CRUD formation) has evolved at all scales: micro, meso and macro. CFD R&D has focused on improvement in closure models for subcooled boiling and bubbly flow, and the formulation of robust numerical solution algorithms. For multiphysics integration, several iterative acceleration methods have been assessed, illuminating areas where further research is needed. Finally, uncertainty quantification and data assimilation techniques, based upon sampling approaches, have been made more feasible for practicing nuclear engineers via R&D on dimensional reduction and biased sampling. Industry adoption of CASL's evolving M&S capabilities, which is in progress, will assist in addressing long-standing and future operational and safety challenges of the nuclear industry. - Highlights: • Complexity of physics based modeling of light water reactor cores being addressed. • Capability developed to help address problems that have challenged the nuclear power industry. • Simulation capabilities that take advantage of high performance computing developed.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Sensitivity analysis of high resolution gamma-ray detection for safeguards monitoring at natural uranium conversion facilities

Under the policies proposed by recent International Atomic Energy Agency (IAEA) circulars and policy papers, implementation of safeguards exists when any purified aqueous uranium solution or uranium oxides suitable for isotopic enrichment or fuel fabrication exists. Under IAEA Policy Paper 18, the starting point for nuclear material under safeguards was reinterpreted, suggesting that purified uranium compounds should be subject to safeguards procedures no later than the first point in the conversion process. In response to this technical need, a combination of simulation models and experimental measurements were employed in previous work to develop and validate gamma-ray nondestructive assay monitoring systems in a natural uranium conversion plant (NUCP). In particular, uranyl nitrate (UO 2 (NO 3 ) 2 ) solution exiting solvent extraction was identified as a key measurement point (KMP). Passive nondestructive assay techniques using high resolution gamma-ray spectroscopy were evaluated to determine their viability as a technical means for drawing safeguards conclusions at NUCPs, and if the IAEA detection requirements of 1 significant quantity (SQ) can be met in a timely manner. Building upon the aforementioned previous validation work on detector sensitivity to varying concentrations of uranyl nitrate via a series of dilution measurements, this work investigates detector response parameter sensitivities to gamma-ray signatures of uranyl nitrate. The full energy peak efficiency of a detection system is dependent upon the sample, geometry, absorption, and intrinsic efficiency parameters. Perturbation of these parameters translates into corresponding variations of the 185.7 keV peak area of the 235 U in uranyl nitrate. Such perturbations in the assayed signature impact the quality or versatility of the safeguards conclusions drawn. Given the potentially high throughput of uranyl nitrate in NUCPs, the ability to assay 1 SQ of material requires uncertainty «1%. Accounting for material self-shielding properties, pipe thickness, and source-detector orientation is instrumental in determining the robustness of gamma-ray detection in the process monitoring of uranyl nitrate in NUCPs. Monte Carlo models and ray-tracing models were employed to determine the sensitivity of the detected 185.7 keV photon to self-shielding properties, pipe thickness, and source-detector geometry. Considering the implementation of the detection of 1 SQ, diversion of 1 SQ becomes essentially undetectable given the systematic uncertainty, in addition to considerations such as propagating uncertainties due to pipe offset/position, as well as minor variations in pipe thickness. Consequently, pipe thickness was the most sensitive variable in affecting full energy efficiency of the 185.7 keV signature peak with up to 8% variation in efficiency for ±0.5 mm changes in Schedule 40 304L stainless steel piping. Furthermore, computation of the attenuation correction factor of the uranyl nitrate solution [CF(AT) (i.e. εsample)] using Parker's method using with the approximation for the geometrical factor κ≈π/4 was validated through experimental, Monte Carlo and ray-tracing calculations for a uranyl nitrate filled transfer pipe segment. Furthermore, quantifying sensitivity in detector position, as well as voiding effects due to bubbly flow or laminar flow with an air gap in the uranyl nitrate becomes increasingly important as considerations from (static) design-scale measurements translate into (dynamic) field operations tests.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Bubbling Reactor Technology for Rapid Synthesis of Uniform, Small MFI-Type Zeolite Crystals

MFI-type zeolite is an important family of materials used in today’s industries as catalysts and adsorbents. Preparation of this type of zeolite material as uniform and pure crystals of sizes from tens of nanometer to hundreds of nanometer are not only desired by current catalytic and adsorption processes for enhanced reaction kinetics and/or selectivity, but also much needed by some new applications, such as CO2 capture adsorbents and composite materials. However, it has been a major challenge in the zeolite synthesis field to prepare small crystals of MFI-type zeolite over a range of Si/Al ratio with very high throughput. In this work, a gas-bubbling flow reactor is used to conduct hydrothermal growth of the zeolite crystals with controllable Si/Al ratio and crystal sizes. Distinctive, uniform ZSM-5 crystals are successfully synthesized within two hours of reaction time, exceptionally short compared to the conventional synthesis process. The crystals are small enough to form a stable milk-like suspension in water. The Si/Al ratio can be controlled by adjusting the growth solution composition and reaction conditions over a range from about 9 to infinity. Characterization by SEM/EDS, XRD, TEM, N2 adsorption/desorption, and NMR confirms ZSM-5 crystal structures and reveals presence of meso-porosity in the resulting crystals.

36 MATERIALS SCIENCE↗

A Comparison of GPU-Accelerated Multiphase CFD Solvers on the Polaris Supercomputer: Part 1

This report is in support of the Innovative and Novel Computational Impact on Theory and Experiment (INCITE) program sponsored by the U.S. Department of Energy (USDOE). With INCITE-level resources, one project, titled BubblyFlow, was granted computational resources for the 2025 calendar year on the Polaris supercomputer at the Argonne Leadership Computing Facility (ALCF). The project aims to conduct simulations to understand the fundamental characteristics of turbulent bubbly flow phenomena in nature. Staff at the ALCF and Argonne’s Computational Science division, along with collaborators at the City College of New York and University of Illinois at Chicago, helped a summer student to assess the accuracy and performance of two high performance computing (HPC) codes. Both codes, ImExLBM and FluTAS, are fundamentally different in their mathematical and numerical modeling. However, both may be used to solve the same physical problem. The collaboration sought to better understand the differences between both codes in terms of accuracy and efficiency. This would ultimately help the BubblyFlow project better utilize resources and establish a knowledge-base of code capabilities in future simulation campaigns. We compare ImExLBM and FluTAS, two high-performance multiphase computational fluid dynamics (CFD) solvers, in terms of physical fidelity, time-to-solution, and parallel efficiency. We validate ImExLBM (Implicit-Explicit Lattice Boltzmann Method) against a canonical benchmark and assess it’s performance relative to FluTAS (Fluid Transport Accelerated Solver), a well-established open-source CFD code.

97 MATHEMATICS AND COMPUTING↗

Application of the hydrogen-bubble technique for velocity measurements in thin liquid films.

A unique adaptation of the hydrogen-bubble flow visualization method was applied to measure velocity profiles and film thicknesses of very thin films on an inclined plane wall. Data were obtained in the three flow regions for a developing falling film with an initially uniform velocity profile and thickness less than or equal to 0.1 in. The measured profiles compared more favorably with parabolic profiles in the intermediate fully developed region than in the initial developing region. However, measured film thicknesses compared favorably with a simplified solution of the integral momentum equation based on parabolic velocity profiles. The results confirm the theoretical prediction that a relatively long distance may be required even for a thin film before nonaccelerating flow with a constant film thickness is obtained and Nusselt's classical analysis applies. The experimental technique was shown to be a practical experimental method for obtaining data for the two-dimensional laminar flow of thin liquid films.

Thomas, W. C.↗