Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “atom probe”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Atom-Specific Probing of Electron Dynamics in an Atomic Adsorbate by Time-Resolved X-Ray Spectroscopy

The electronic excitation occurring on adsorbates at ultrafast timescales from optical lasers that initiate surface chemical reactions is still an open question. Here, in this work, we report the ultrafast temporal evolution of x-ray absorption spectroscopy (XAS) and x-ray emission spectroscopy (XES) of a simple well-known adsorbate prototype system, namely carbon (C) atoms adsorbed on a nickel [Ni(100)] surface, following intense laser optical pumping at 400 nm. We observe ultrafast (~100 fs) changes in both XAS and XES showing clear signatures of the formation of a hot electron-hole pair distribution on the adsorbate. This is followed by slower changes on a few picoseconds timescale, shown to be consistent with thermalization of the complete C/Ni system. Density functional theory spectrum simulations support this interpretation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Correlative STEM-APT characterization of radiation-induced segregation and precipitation of in-service BWR 304 stainless steel

In this study, radiation induced segregation and precipitation phenomena in an in-service boiling water reactor 304 stainless steel component were investigated using directly correlated 3D-atom probe tomography and scanning transmission electron microscopy. Significant quantitative differences in measured segregation at grain boundaries were found between the atom probe and energy dispersive spectroscopy measurements of the exact same locations. In particular, a much stronger Si segregation (~10 atomic% via atom probe versus ~4 atomic% via electron microscopy) and different Cr profile shapes were detected that are critical to models of radiation induced segregation and stress corrosion cracking behavior. These quantitative differences highlight the need for comparative microscopy and critical evaluation of limitations in each analytical method. Elemental segregation to dislocations and conjoined-clusters were also highlighted by atom probe; confirming and expanding upon what has been observed in test reactor neutron and accelerator-based ion irradiations.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Local p‐ and n‐Type Doping of an Oxide Semiconductor via Electric‐Field‐Driven Defect Migration

Layered oxides exhibit high ionic mobility and chemical flexibility, attracting interest as cathode materials for lithium-ion batteries and the pairing of hydrogen production and carbon capture. Recently, layered oxides emerged as highly tunable semiconductors. For example, by introducing anti-Frenkel defects, the electronic hopping conductance in hexagonal manganites is increased locally by orders of magnitude. Here, local acceptor and donor doping in Er(Mn,Ti)O3 is demonstrated, facilitated by the controlled splitting of anti-Frenkel defects under applied d.c. voltage. By combining density functional theory calculations, scanning probe microscopy, atom probe tomography, and scanning transmission electron microscopy, it is shown that the oxygen defects can readily be moved through the layered crystal structure, leading to nano-sized interstitial-rich (p-type) and vacancy-rich (n-type) regions. The resulting pattern is comparable to dipolar npn-junctions and stable on the timescale of days. These findings reveal the possibility of temporarily functionalizing oxide semiconductors at the nanoscale, giving additional opportunities for the field of oxide electronics and the development of transient electronics in general.

He, Jiali↗
DOE OSTI2023

Strengthening model development and effects of low diffusing solutes to coarsening resistance in aluminum alloys

A modified Orowan strengthening model is proposed to account for finite rod-shaped precipitates with hemispherical caps in aluminum alloy systems. A combined computational and experimental approach is used to study the influences of anisotropic Orowan looping and solute-dislocation interaction on temperature-dependent yield strength. Here, the strengthening model is validated with a dataset containing 297 experimental precipitate geometries, chemistries, temperatures, and strength measurements, and achieves a strong predictive correlation of 0.8713 with experimentally measured yield strengths. Under conditions that are applicable to coarsening, constant particle volume fraction and aspect ratio, the model predicts that short rod precipitates provide far superior strengthening effects compared to plate precipitates. A cast Al-Si-Mg-Cu alloy with rod-shaped Q-phase (Al 3 Cu 2 Mg 9 Si 7 ) precipitates was developed with a novel chemistry exploring the use of low-diffusivity elements (Mn, Ni, V, Zr) to limit precipitate coarsening. The thermodynamic behavior of Mn, Ni, V, and Zr across the Q-phase interface is examined using transmission electron microscopy (TEM), first-principles density-functional theory (DFT) calculations. and atom-probe tomography (APT). DFT calculations utilizing TEM identified Q-phase/Al-matrix interfaces show that Mn, Ni, V, and Zr preferentially segregate to the Q-phase precipitate boundaries which suggests inhibition of precipitate coarsening and higher strengths after temperature exposure. Atom-probe tomography confirms solute atom partitioning/segregation at the Q-phase/Al-matrix interface, found in the modified commercial AS7GU alloy (A356 +0.5%Cu), which supports these observations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Multi-scale characterization of supersolidus liquid phase sintered H13 tool steel manufactured via binder jet additive manufacturing

Additive manufacturing (AM) of H13 tool steel by binder jet 3D printing (BJ3DP) followed by pressureless supersolidus liquid phase sintering (SLPS) provides a low-cost alternative manufacturing method for components with intricate geometric features. However, the microstructure-mechanical property relationships for BJ3DP-SLPS produced H13 tool steel are not well understood, which makes it challenging to develop printing and post-processing methods that maximize part performance. In this work, we leverage atom probe tomography and transmission electron microscopy along with thermodynamic calculations to rationalize the microstructure-mechanical property relationships in as-sintered BJ3DP H13 tool steel. Here, we report for the first time, the presence of a continuous eutectic film-like carbide in H13 along with the more commonly observed cuboidal MX carbides in the prior liquid channels of the microstructure. Further, atom probe tomography revealed the interconnected nature of the MX carbides that appear to be discrete in two-dimensional micrographs. These continuous eutectic carbides and interconnected MX carbides result in brittle failure of the material. Characterization of these microstructural features will be critical in developing appropriate post-processing heat treatments for the improved mechanical performance of BJ3DP H13.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Emergent symmetries in atomic nuclei: Probing nuclear dynamics and physics beyond the standard model

Dominant shapes naturally emerge in atomic nuclei from first principles, thereby establishing the shape-preserving symplectic Sp(3, \mathbb{R} ℝ ) symmetry as remarkably ubiquitous and almost perfect symmetry in nuclei. We discuss the critical role of this emergent symmetry in enabling machine-learning descriptions of heavy nuclei, ab initio modeling of \alpha α clustering and collectivity, as well as tests of beyond-the-standard-model physics. In addition, the Sp(3, \mathbb{R} ℝ ) and SU(3) symmetries provide relevant degrees of freedom that underpin the ab initio symmetry-adapted no-core shell model with the remarkable capability of reaching nuclei and reaction fragments beyond the lightest and close-to-spherical species.

Launey, Kristina D.↗
DOE OSTI2023

Probing the atomically diffuse interfaces in Pd@Pt core-shell nanoparticles in three dimensions

Deciphering the three-dimensional atomic structure of solid-solid interfaces in core-shell nanomaterials is the key to understand their catalytical, optical and electronic properties. Here, we probe the three-dimensional atomic structures of palladium-platinum core-shell nanoparticles at the single-atom level using atomic resolution electron tomography. We quantify the rich structural variety of core-shell nanoparticles with heteroepitaxy in 3D at atomic resolution. Instead of forming an atomically-sharp boundary, the core-shell interface is found to be atomically diffuse with an average thickness of 4.2 Å, irrespective of the particle’s morphology or crystallographic texture. The high concentration of Pd in the diffusive interface is highly related to the free Pd atoms dissolved from the Pd seeds, which is confirmed by atomic images of Pd and Pt single atoms and sub-nanometer clusters using cryogenic electron microscopy. These results advance our understanding of core-shell structures at the fundamental level, providing potential strategies into precise nanomaterial manipulation and chemical property regulation.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2021

Bulk and Short-Circuit Anion Diffusion in Epitaxial Fe 2 O 3 Films Quantified Using Buried Isotopic Tracer Layers

Self-diffusion is a fundamental physical process that, in solid materials, is intimately correlated with both microstructure and functional properties. In this work, a universal approach is presented to precisely characterize self-diffusion in ionic solids by isotopically enriching anions and/or cations at specific locations within an epitaxial film stack, and characterize their redistribution at high spatial resolution with atom probe tomography. Nanoscale anion diffusivity is quantified in epitaxial α-Fe 2 O 3 thin films deposited by molecular beam epitaxy with a thin (10 nm) buried layer highly enriched in 18 O. The isotopic sensitivity of the atom probe allows precise measurement of 18 O distribution across the sharp interfaces between this layer and the surrounding Fe 2 O 3 after annealing. Short-circuit anion diffusion through 1D and 2D structural defects in Fe 2 O 3 are also directly visualized in 3D. This versatile approach to study precisely tailored thin film samples at high spatial and mass fidelity will facilitate a deeper understanding of atomic-scale diffusion phenomena.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Influence of processing on secondary phase formation and microstructural evolution at U-10Mo alloy and Zr interlayer interfaces

Thermo-mechanical processing of uranium-10 wt. % molybdenum (U-10Mo) fuel plates leads to microstructure changes at the U-10Mo/Zr interfaces. Secondary phases formed at this interface are particularly important to interfacial bond strength, process optimization, and maintaining structural integrity of the U-10Mo fuel plates during irradiation. In this work, we determined the phases and phase transformation products occurring at the interface of the U-10Mo fuel and Zr interlayer when the fuel plate is subjected to short and long hot isostatic pressure times. Interfacial morphology, structure and composition of phases formed, and relative hardness across the U-10Mo/Zr interfaces were studied using a multi-length scale, multi-modal characterization approach involving electron microscopy, atom probe tomography, and atomic force microscopy. Here, results highlight that the extent of phase transformations, secondary phase formation, and hardness variability across interfaces can be controlled by modifying processing parameters. Phase diagram construction and thermodynamic calculations were performed using the Thermocalc software to identify expected phases formed at interfaces during the maximum hold temperature of 560 °C experienced during HIP.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Radiation-Enhanced Anion Transport in Hematite

The influence of radiation-induced (1 MeV energy H+ to ~0.1 dpa at 450°C), non-equilibrium point defect populations on mass transport is studied with an integrated campaign of experimental and theoretical methods. Using epitaxial thin films of hematite with embedded 18O tracer layers and nanoscale atom probe tomography measurements, it is shown that anion self-diffusion is enhanced by at least 2 orders of magnitude under irradiation compared to thermal diffusion alone. Complementary scanning transmission electron microscopy of vacuum annealed specimens, reveals associated microstructural changes in the oxide films, including local phase transformation to Fe3O4 and the development of nanoscale voids from vacancy coalescence. Point defect formation and migration energies were computed from density functional theory and applied within the context of chemical rate theory to analyze contributions from both interstitial and vacancy mechanisms to self-diffusion in thermal and irradiation conditions. Comparisons are made between calculated, literature and newly measured self-diffusion values, revealing good agreement on the magnitude of radiation-enhanced anion diffusion. Further, the model suggests a transition from vacancy to interstitialcy mechanisms at low temperatures and high oxygen activity, consistent with the varied activation energies reported from prior studies.

iron oxides, isotopic tracers, atom probe tomograp↗
DOE OSTI2021

Understanding the microstructural stability in a y’-strengthened Ni-Fe-Cr-Al-Ti alloy

Ni-Fe-Cr-Al-Ti alloys, with Ni levels near 50 wt.%, have the potential to develop a microstructure consisting of a face-centered cubic ? matrix with the homogeneous precipitation of fine ordered ?’ precipitates similar to traditional Ni-based superalloys with significantly greater Ni content. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), atom probe tomography (APT), and CALPHAD -based thermodynamic modeling were employed to understand the phase stabilities and microstructural evolution in an age-hardenable Ni-27Fe-18Cr-1Co-1.6Al-3.75Ti-1.2Mo-0.03C (wt%) alloy. The primary heat-treatment of solution annealing at 1121°C for 4h and age-hardening treatment at 760 °C for 16h resulted in a microstructure consisting of fine ?’ precipitates in an austenitic matrix along with grain boundary carbides, consistent with thermodynamic calculations. Long-term aging at 900 °C for 250h resulted in the coarsening of ?’ along with a change in the morphology of the precipitates from spherical to a more cuboidal shape. In addition, ? phase formation was observed concomitant with the partial dissolution of the ?’ phase. The ability of computational thermodynamic models to predict microstructural characteristics is discussed.

Gwalani, Bharat↗
DOE OSTI2020

Monte Carlo simulations of Cu/Ni–Si–Mn co-precipitation in duplex stainless steels

First-Passage Kinetic Monte Carlo (FPKMC) simulations of species migration in duplex stainless steels were performed in order to establish relationships between alloy content, segregation behavior, and the formation of Ni-Si-Mn rich particles in cast duplex stainless steels during thermal aging. The Ni-Si-Mn-rich second phase forms after extended aging at reactor operating temperatures and degrades alloy properties. Simulations of Ni-Si-Mn cluster formation were validated through comparison with experimental results obtained through Atom Probe Tomography (APT) on similar alloy compositions, identifying several trends. First, Cu promotes the formation of Ni-Si-Mn clusters, but only when Ni or Mn prefer segregation to the surface of Cu particles; without the segregation of these species, the critical composition for the clusters to form was not achieved. Second, the width of precipitate-denuded zones near ?/d interfaces increases with decreasing Cu content. This finding was in strong agreement with APT results, further validating our model. Finally, our model predicts that Ni-Si-Mn cluster formation will be the most extensive when the Si:Mn ratio is approximately 1:1 and the least extensive when one of these key elements is less concentrated (Mn = 0.5 at.% or Si = 0.5 at.%). The implications of these results on how to improve alloy properties are discussed.

Cu co-precipitation, Atom probe tomography (APT), ↗
DOE OSTI2022

Manipulating and Probing Ultrafast Atomic and Molecular Dynamics (Final Report)

This program has focused on the exploration and control of dynamics in atoms, small molecules, clusters, and micro- or nano-structures following ultrafast excitation and/or driven by strong oscillating fields. In our principal experiments, gas phase atoms and molecules were exposed to short pulses of electromagnetic radiation with frequencies ranging from THz into the XUV spectral regions, and with durations from picoseconds to attoseconds. The pulses coherently induce and/or probe dynamics in the electronic, vibrational, and rotational degrees of freedom of the targets. The overarching goal of the various projects has been to exploit strong-field processes and/or implement novel ultrafast techniques for manipulating and probing coherent electronic and nuclear motion. Typically, the relevant system evolution occurs over attosecond to picosecond timescales. In doing so, we have gained a more complete picture of correlated multi-particle dynamics in atoms, molecules, and other complex systems and expanded the toolbox of useful techniques for manipulating and probing those dynamics. Grant funds were primarily used to: (i) pay salaries and fringe benefits for the PI and postdocs and stipends, tuition, and health care costs for graduate students; (ii) cover travel expenses for the PI, postdocs, and students to attend and participate in professional meetings, conferences, and workshops; and (iii) purchase research materials, supplies, and equipment required for experiments. The research resulted in the publication of 24 peer reviewed articles (including 1 in Nature Physics, 2 in Nature Communications, 7 in Physical Review Letters, and 12 in Physical Review A), and 4 PhD dissertations. The specific results from different funding periods are summarized separately in the main report.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2022

Correlation between thickness dependent nanoscale structural chemistry and superconducting properties of ultrathin epitaxial NbN films

NbN-based superconductors have attracted interest for superconducting circuits, quantum computation and high frequency devices. The superconducting properties of NbN films are predominately reliant on the microstructure, therefore, an atomic-level understanding of the structure-chemistry is required to achieve high quality epitaxial NbN films. Here, in this study, the thickness-dependent superconducting properties of NbN films (5, 10, and 50 nm) within NbN/AlN/Al 2 O 3 heterostructures are investigated. NbN and AlN were epitaxially grown by an industrial scale physical vapor deposition technique. The role of nanoscale chemistry on the ultrathin NbN superconducting film is investigated at the atomic level for the first time via atom probe tomography, providing three-dimensional atomic distribution, chemical homogeneity, effect of impurities, specially, in secondary phase formations and interfacial abruptness. The NbN film with 5 nm of thickness demonstrates a superconducting transition temperature of 11.2 K as compared to 50 nm NbN films with a transition temperature of 15.3 K. These thickness dependent variation of superconducting properties are associated with the chemical inhomogeneity in terms of in-plane N:Nb distribution, secondary phase formations and NbN/AlN interfacial abruptness as a function of the NbN films thicknesses. The analysis depicts the interplay between the surface/interface and the superconducting properties of ultrathin NbN films. These results provide insights on material design and growth that will enable the development of optimized superconducting NbN films for quantum devices.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Targeting Aspergillus allergen oryzin with a chemical probe at atomic precision

We report the molecular basis of Aspergillus fumigatus oryzin, allergen Asp f 13, or alkaline proteinase ALP1, containing the sequence motif His–Asp–Ser of the subtilisin family, structure, and function at atomic detail. Given the resolution of the data (1.06 Å), we use fragment molecular replacement with ideal polyalanine α-helices to determine the first crystal structure of oryzin. We probe the catalytic serine through formation of an irreversible bond to a small molecule compound, specifically labeling it, describing the amino acid residues performing the catalytic function. Defined by a self-processed pro-peptide, the active site architecture shapes up pocket-like subsites that bind to and unveil the S1′–S4′ substrate binding preferences. We use molecular modeling to dock a model of the pro-peptide in the S1–S4 region and to dock collagen along the active site cleft. Opposite to the face harboring the catalytic serine, the enzyme binds to a calcium ion in a binding site created by backbone flipping. We use thermal unfolding to show that this metal ion provides structural stability. With no known host inhibitor identified thus far, this structure may hasten the progress of developing new therapeutic agents for diseases caused by pathogenic fungi.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Microstructure, electrical resistivity, and tensile properties of neutron-irradiated Cu–Cr–Nb–Zr

High strength, high conductivity copper alloys that can resist creep at high temperatures are one of the primary candidates for efficient heat exchangers in fusion reactors. Cu–Cr–Nb–Zr (CCNZ) alloys, which were designed to improve the strength and creep life of ITER Cu–Cr–Zr (CCZ) reference alloys, have been found to have comparable electrical conductivity and tensile properties to CCZ alloys. The measured creep rupture times for these improved alloys is about ten times higher than the ITER reference alloys at 90–125 MPa at 500 °C. However, the effects of neutron irradiation on these alloys, and the ensuing material properties, have not been studied; thus, their utility in a fusion reactor environment is not well understood. This study characterizes the room temperature mechanical and electrical properties of a neutron-irradiated CCNZ alloy and compares them to a neutron-irradiated ITER reference heat sink CCZ alloy. Tensile specimens were neutron irradiated in the High Flux Isotope Reactor (HFIR) to 5 dpa between 250 °C and 325 °C. Post-irradiation characterization included electrical resistivity measurements, hardness, and tensile tests. Microstructural evaluation used scanning electron microscopy, energy dispersive x-ray spectroscopy, and atom probe tomography to characterize the irradiation-produced changes in the microstructure and investigate the mechanistic processes leading to post-irradiation properties. Transmutation calculations were validated with composition measurements from atom probe data and used to calculate contributions to the increased electrical resistivity measured after irradiation. Comparisons with CCZ alloys in the same irradiation heat found that the post-irradiated CCNZ and CCZ alloys had comparable electrical resistivity. Although CCNZ alloys suffered more irradiation hardening than CCZ, the overall tensile behavior deviated very little from non-irradiated values in the temperature range studied.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Atomic-scale probing of short-range order and its impact on electrochemical properties in cation-disordered oxide cathodes

Abstract Chemical short-range-order has been widely noticed to dictate the electrochemical properties of Li-excess cation-disordered rocksalt oxides, a class of cathode based on earth abundant elements for next-generation high-energy-density batteries. Existence of short-range-order is normally evidenced by a diffused intensity pattern in reciprocal space, however, derivation of local atomic arrangements of short-range-order in real space is hardly possible. Here, by a combination of aberration-corrected scanning transmission electron microscopy, electron diffraction, and cluster-expansion Monte Carlo simulations, we reveal the short-range-order is a convolution of three basic types: tetrahedron, octahedron, and cube. We discover that short-range-order directly correlates with Li percolation channels, which correspondingly affects Li transport behavior. We further demonstrate that short-range-order can be effectively manipulated by anion doping or post-synthesis thermal treatment, creating new avenues for tailoring the electrochemical properties. Our results provide fundamental insights for decoding the complex relationship between local chemical ordering and properties of crystalline compounds.

25 ENERGY STORAGE↗
DOE OSTI2022

Alloy Partitioning Effect on Strength and Toughness of κ-Carbide Strengthened Steels

Alloy partitioning during heat treatment in a lightweight precipitation hardened steel was investigated using transmission electron microscopy and atom probe tomography. The mechanical properties are discussed as a function of the effect of solution treatment temperature and aging time, giving rise to variations in chemical modulation. A wrought lightweight steel alloy with a nominal composition of Fe-30Mn-9Al-1Si-1C-0.5Mo (wt. %) was solution-treated between 1173–1273 K and aged at 773 K. Lower solution treatment temperatures retained a finer grain size and accelerated age hardening response that also produced an improved work hardening behavior with a tensile strength of -1460 MPa at 0.4 true strain. Atom probe tomography indicated these conditions also had reduced modulation in the Si and Al content due to the reduced aging time preventing silicon from diffusing out of the κ-carbide into the austenite. This work provides the framework for heat-treating lightweight, age hardenable steels with high strength and improved energy absorption.

36 MATERIALS SCIENCE↗