Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “YOUNG MODULUS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Tensile and pack compressive tests of some sheets of aluminum alloy, 1025 carbon steel, and chromium-nickel steel

Tensile and compressive stress-strain curves, stress-deviation curves, and secant modulus-stress curves are given for longitudinal and transverse specimens of 17S-T, 24S-T, and 24S-RT aluminum-alloy sheet in thicknesses from 0.032 to 0.081 inch, 1025 carbon steel sheet in thicknesses of 0.054 and 0.120 inch, and chromium-nickel steel sheet in thicknesses form 0.020 to 0.0275 inch. Significant differences were found between the tensile and the compressive stress-strain curves, and also the corresponding corollary curves; similarly, differences were found between the curves for the longitudinal and transverse directions. These differences are of particular importance in considering the compressive strength of aircraft structures made of thin sheet. They are explored further for the case of compression by giving tangent modulus-stress curves in longitudinal and transverse compression and dimensionless curves of the ratio of tangent modulus to Young's modulus and of the ratio of reduced modulus for a rectangular section to Young's modulus, both plotted against the ratio of stress to secant yield strength.

Atchison, C S↗

The Effect of Citric Acid on Physicochemical Properties of Hydrophilic Carboxymethyl Starch-Based Films

The carboxymethyl starch-based films in a presence of citric acid were prepared by casting technique. The influence of citric acid content on physicochemical properties of obtained hydrophilic films were evaluated (solubility in water, moisture absorption, mechanical and thermal properties). The crosslinking of starch derivative chains has been confirmed by FTIR spectroscopy, however, an excess of citric acid could cause hydrolysis of carboxymethyl starch chains. The best mechanical performance has been noted for the system containing 30 wt% (the highest tensile strength as well Young modulus 160 kPa and 650 kPa, respectively) as well as the highest T{sub g} (ca. 58 °C). Additionally for the mentioned system the lowest solubility in water has been determined.

36 MATERIALS SCIENCE↗

Effect of film thickness on structural and mechanical properties of AlCrN nanocompoite thin films deposited by reactive DC magnetron sputtering

In this study, the influence of film thickness on the structural, surface morphology and mechanical properties of Aluminum chromium nitride (AlCrN) thin films has been successfully investigated. The AlCrN thin films were deposited on silicon (100) substrate using dc magnetron reactive co-sputtering at substrate temperature 400° C. The structural, surface morphology and mechanical properties were studied using X-ray diffraction, field-emission scanning electron microscopy and nanoindentation techniques respectively. The thickness of these thin films was controlled by varying the deposition time therefore increase in deposition time led to increase in film thickness. X-ray diffraction pattern of AlCrN thin films with different deposition time shows the presence of (100) and (200) orientations. The crystallite size varies in the range from 12.5 nm to 36.3 nm with the film thickness due to surface energy minimization with the higher film thickness. The hardness pattern of these AlCrN thin films follows Hall-Petch relation. The highest hardness 23.08 Gpa and young modulus 215.31 Gpa were achieved at lowest grain size of 12.5 nm.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

A DFT Study on Structural, Electronic Mechanical and Thermodynamic Properties of 5f-Electron System BaAmO{sub 3}

The structural, electronic, mechanical and thermodynamic properties of the perovskite oxide BaAmO{sub 3} have been predicted using the full-potential linearized augmented plane wave (FP-LAPW) method. The equilibrium lattice constant, bulk modulus and pressure derivative were computed using different exchange correlations. The optimization of structure was carried out in ferromagnetic, anti-ferromagnetic and non-magnetic states, and the compound was found to be stable in the ferromagnetic state. A systematic study on the band structure and density of states was accomplished using generalized gradient approximation (GGA), Hubbard approximation (GGA + U) and modified Becke–Johnson exchange potential (mBJ),and the compound was found to have a half-metallic nature in all the approximations. The calculated total spin magnetic moment was found to be 5 μ{sub B} in all the approximations used. The second-order elastic constants, Young modulus, shear modulus, Poisson ratio and anisotropic factor have also been calculated. In order to have a complete understanding of BaAmO{sub 3}, the thermodynamic properties were studied in the pressure range of 0 to 40 GPa and the temperature range extending from 0 to 600 K.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electronic structures, elastic properties, and minimum thermal conductivities of cermet M{sub 3}AlN

The electronic structures and elastic anisotropies of cubic Ti{sub 3}AlN, Zr{sub 3}AlN, and Hf{sub 3}AlN are investigated by pseudopotential plane-wave method based on density functional theory. At the Fermi level, the electronic structures of these compounds are successive with no energy gap between conduct and valence bands, and exhibit metallicity in ground states. In valence band of each partial density of states, the different orbital electrons indicate interaction of corresponding atoms. In addition, the anisotropy of Hf{sub 3}AlN is found to be significantly different from that of Ti{sub 3}AlN and Zr{sub 3}AlN, which involve the differences in the bonding strength. It is notable that Hf{sub 3}AlN is a desired thermal barrier material with the lowest thermal conductivity at high temperature among the three compounds. - Graphical abstract: 1.Young's moduli of anti-perovskite Ti{sub 3}AlN, Zr{sub 3}AlN, and Hf{sub 3}AlN in full space. 2.Electron density differences on crystal planes (1 0 0), (2 0 0), and (1 1 0) of anti-perovskite Zr{sub 3}AlN. - Highlights: • We calculated three anti-perovskite cermets with first-principles theory. • We illustrated 3D Young modulus and found the anomalous anisotropy. • We explained the anomaly and calculated the minimum thermal conductivities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Numerical Simulation Of Steel Plate Bending Process Using Stationary Laser Beam By A Coupled Finite Element Thermal Mechanical Analysis

We analyze the deformation induced by focusing a CW high power laser beam on stainless steel plate. A non-linear 3D finite element approach is used to simulate the thermo-elastoplastic deformation, the heat conduction, and stresses. Material properties including density, yield stress, Young modulus, specific heat, and thermal expansion coefficient are considered as temperature-dependent. The effect of heating time on transient temperatures, stresses, strains and bending angles during the process is studied, and the process parameters affecting the bending angles were also investigated.

36 MATERIALS SCIENCE↗

Structural characterisation of BaTiO{sub 3} thin films deposited on SrRuO{sub 3}/YSZ buffered silicon substrates and silicon microcantilevers

We report on the progress towards an all epitaxial oxide layer technology on silicon substrates for epitaxial piezoelectric microelectromechanical systems. (101)-oriented epitaxial tetragonal BaTiO{sub 3} (BTO) thin films were deposited at two different oxygen pressures, 5.10{sup −2} mbar and 5.10{sup −3} mbar, on SrRuO{sub 3}/Yttria-stabilized zirconia (YSZ) buffered silicon substrates by pulsed laser deposition. The YSZ layer full (001) orientation allowed the further growth of a fully (110)-oriented conductive SrRuO{sub 3} electrode as shown by X-ray diffraction. The tetragonal structure of the BTO films, which is a prerequisite for the piezoelectric effect, was identified by Raman spectroscopy. In the BTO film deposited at 5.10{sup −2} mbar strain was mostly localized inside the BTO grains whereas at 5.10{sup −3} mbar, it was localized at the grain boundaries. The BTO/SRO/YSZ layers were finally deposited on Si microcantilevers at an O{sub 2} pressure of 5.10{sup −3} mbar. The strain level was low enough to evaluate the BTO Young modulus. Transmission electron microscopy (TEM) was used to investigate the epitaxial quality of the layers and their epitaxial relationship on plain silicon wafers as well as on released microcantilevers, thanks to Focused-Ion-Beam TEM lamella preparation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The Effect of Zinc on the Structural, Electrical, and Mechanical Properties of YBCO-123 Superconducting Nanoparticles Prepared by an Acetate-Based Sol-Gel Process

In this study, zinc (Zn)-doped YBaCuO (YBCO)-123-based high-temperature superconducting samples were produced using the sol-gel method, which is commonly used for preparing nanosize materials. Zn ions were substituted by Cu ions (YBa{sub 2}Cu{sub 3-x}Zn{sub x}O), and Zn doping effects on structural, electrical, and mechanical properties of the YBCO-123 superconductors were examined in detail. Undoped sample was prepared under same conditions. X-ray diffraction analysis (XRD) was used to determine phase analysis and lattice parameters of the superconducting samples. To analyze the microstructure properties, scanning electron microscope (SEM) measurements were performed. Resistivity and microhardness measurements were also carried out for superconducting and mechanic properties, respectively. Vickers microhardness, young modulus, fracture toughness, and yield strength values of the samples were calculated. Microhardness measurements were analyzed using the Kick’s law, proportional sample resistance (PSR) model, EPD model, the Hays-Kendall (HK) approach, and indentation-induced cracking (IIC) model.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ab Initio Investigation on Electronic, Magnetic, Mechanical, and Thermodynamic Properties of AMO{sub 3} (A = Eu, M = Ga, In) Perovskites

The structural, electronic, magnetic, elastic, and thermodynamic properties of cubic AMO{sub 3} perovskites (A = Eu, M = Ga, In) have been successfully studied within density functional theory using full-potential linearized augmented plane wave (FP-LAPW). The structural study reveals that both the compounds are stable in ferromagnetic states. The GGA + U calculated spin-polarized electronic band and density of states present the half-metallic nature of both the compounds. The magnetic moments calculated with different approximations were found to be approximately 6 μ{sub B} for EuGaO{sub 3} and approximately 7 μ{sub B} for EuInO{sub 3}. From elastic calculation, the three independent elastic constants (C{sub 11}, C{sub 12}, C{sub 44}) have been acquired to yield the mechanical properties like Young modulus (Y ), shear modulus (G), Poisson ratio (ν), and anisotropic factor (A). The calculated values of B/G show that both the compounds are ductile in nature. The thermodynamic study was also accomplished by exploring the thermodynamic parameters like specific heat, heat capacity, thermal expansion, Grüneisen parameter, Debye temperature, etc. within the temperature range 0 to 900 K and pressure range 0 to 50 GPa.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Assessment of mechanical, thermal properties and crystal shapes of monoclinic tricalcium silicate from atomistic simulations

The two most common polymorphs in industrial alite, M1 and M3, were characterized at the molecular scale. Different methods were employed and discussed to assess mechanical properties and specific heat of both polymorphs. The calculated homogenized elastic moduli and specific heat were found in good agreement with experimental measurements. A comparative analysis of spacial Youngs modulus reveal isotropic and anisotropic spacial distribution for M{sub 1} and M{sub 3} respectively. A more isotropic compressive strength is also reported for M{sub 1} when compared to M{sub 3} polymorph. Cleavage energies computation allowed to proposed equilibrium shapes for both polymorph, with significant differences. While the lowest cleavage energies were found along (100) and (001) for both polymorphs, the constructed M1 crystal possesses 3 independent facets, against seven for the M3 polymorph.

36 MATERIALS SCIENCE↗

The Probe Length Effect on the Cantilever of an Atomic Force Microscope in Measuring the Mechanical Properties of Living Neurons

Living sensory neurons were studied by atomic force microscopy in the PeakForce QNM mode under near-physiological conditions. The dependence of the measured apparent Young modulus of cells on the ratio of the probe height to the beam length on a used cantilever was revealed. A qualitative explanation based on the analysis of beam strains in two limit cases, in which the probe slides over a studied object and the probe sticks to the latter, was given to the obtained result. It was proposed to classify native cells by the character of their interaction with the probe (sliding or sticking).

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Mechanical and thermal properties of h-MX{sub 2} (M = Cr, Mo, W; X = O, S, Se, Te) monolayers: A comparative study

Using density functional theory, we obtain the mechanical and thermal properties of MX{sub 2} monolayers (where M = Cr, Mo, W and X = O, S, Se, Te). The Γ-centered phonon frequencies (i.e., A{sub 1}, A{sub 2}{sup ″}, E′, and E″), relative frequency values of A{sub 1}, and E′ modes, and mechanical properties (i.e., elastic constants, Young modulus, and Poisson's ratio) display a strong dependence on the type of metal and chalcogenide atoms. In each chalcogenide (metal) group, transition-metal dichalcogenides (TMDCs) with W (O) atom are found to be much stiffer. Consistent with their stability, the thermal expansion of lattice constants for TMDCs with O (Te) is much slower (faster). Furthermore, in a heterostructure of these materials, the difference of the thermal expansion of lattice constants between the individual components becomes quite tiny over the whole temperature range. The calculated mechanical and thermal properties show that TMDCs are promising materials for heterostructures.

36 MATERIALS SCIENCE↗

Effect of reprocessing cycles on the degradation of polypropylene copolymer filled with talc or montmorillonite during injection molding process

Mechanical recycling of polymeric materials is a favorable technique resulting in economic and environmental benefits, especially in the case of polymers with a high production volume as the polypropylene copolymer (PP). However, recycling by reprocessing techniques can lead to thermal, mechanical or thermo-oxidative degradation that can affect the structure of the polymer and subsequently the material properties. PP filled with montmorillonite (MMT) or talc are widely produced and studied, however, its degradation reactions by reprocessing cycles are poorly studied so far. In this study, the effects of reprocessing cycles in the structure and in the properties of the PP/MMT and PP/Talc were evaluated. The samples were mixed with 5% talc or MMT Cloisite C15A in a twin-screw extrusion. After extrusion, this filled material was submitted to five reprocessing cycles through an injection molding process. In order to evaluate the changes induced by reprocessing techniques, the samples were characterized by DSC, FT-IR, Izod impact and tensile strength tests. The study showed that Young modulus, elongation at brake and Izod impact were not affected by reprocessing cycles, except when using talc. In this case, the elongation at brake reduced until the fourth cycle, showing rigidity increase. The DSC results showed that melting and crystallization temperature were not affected. A comparison of FT-IR spectra of the reprocessed indicated that in both samples, between the first and the fifth cycle, no noticeable change has occurred. Thus, there is no evidence of thermo oxidative degradation. In general, these results suggest that PP reprocessing cycles using MMT or talc does not change the material properties until the fifth cycle.

36 MATERIALS SCIENCE↗

Estimating the mechanical properties of hydrating blended cementitious materials: An investigation based on micromechanics

The hydration model of Parrot & Killoh (1984) has been extended to blended cements and coupled to a micromechanical scheme similar to that of Pichler & Hellmich (2011) to estimate the Young modulus and the compressive strength of cementitious materials as a function of time. A finite aspect ratio of 7 is introduced to describe the shape of the hydrates and improve the estimate of the early age strength by the micromechanical scheme. Furthermore, accounting for the stress fluctuations in the cement paste partly explains the fact that the compressive strength of a concrete can be lower than that of its cement paste. Finally, the estimated physical properties are compared to numerous experimental measurements from the literature and new experimental measurements on blended cement pastes featuring significant weight fractions of limestone filler, fly ash or silica fume. It is shown that the present model slightly overestimates the dilution effect.

36 MATERIALS SCIENCE↗

Two-Step Procedure of Fly Ash Modification as an Alternative Method for Creation of Functional Composite

An appropriate filler is a key component required to achieve an useful composite with expected properties. Not only sophisticated types of filler, like graphene are popular, but also more common ones, like silica flour or fly ash because of their low costs. Besides production costs, adequate size and possibility of functionalization of particles surface to create stable bonds with a matrix are essential in filler selection. To create an useful filler for epoxy resin based composites with use of a waste material, namely fly ash, two-step procedure was proposed. In the first part, raw material was sieved and five different ranges of the filler size were obtained. After mechanical tests with fracture toughness, tensile strength and Young Modulus, as well thermal conductivity, the best size of the fly ash was chosen for further modification. During the second step, filler was modified with coupling agent [3-(2-aminoethylamino)propyl]trimethoxysilane in order to enhance the coupling between particular components of composite. Presence of the silane layer was confirmed with infrared spectroscopy and scanning electron microscopy measurements, whilst prepared epoxy composite filled with silanized fly ash was examined similarly as previous composites. Obtained results have proved the significant influence of size of a filler and bonding to the matrix on mechanical and thermal properties of fly ash-epoxy resin composite. Proposed simple method of fly ash modification is an environmentally friendly way for utilization of the fly ash. Moreover, it creates an alternative material applicable in electrical devices as functional composite.

36 MATERIALS SCIENCE↗

Nanostructured cobalt powders synthesised by polyol process and consolidated by Spark Plasma Sintering: Microstructure and mechanical properties

Bulk nanostructured cobalt was processed using a bottom-up strategy. Nanostructured particle agglomerates of about 50 and 240 nm in diameter were synthesised using a polyol route and subsequently consolidated by Spark Plasma Sintering (SPS). The microstructure of the starting powders and of the processed bulk samples was studied and characterised by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The XRD patterns of the as-prepared powders showed predominantly a face centred cubic (fcc) crystalline phase, whereas both fcc and hexagonal close packed (hcp) phases were found within the consolidated samples. A sample with the highest relative mass density (94.5%) was obtained from the small powder particles. TEM observations revealed a lamellar substructure with a high density of nanotwins and stacking faults in every grain in the sample with the highest density. Brillouin light scattering (BLS) and quasistatic compression tests were used to investigate the mechanical properties of the consolidated samples. The two techniques yielded Young modulus values of 168 GPa and 130 GPa, respectively, in the sample with the highest density. This sample also exhibited a yield stress higher than 1 GPa after the compression test, which is mainly attributed to the lamellar-like structure occurring in almost every grain of the polycrystalline aggregate. - Highlights: Black-Right-Pointing-Pointer Cobalt nanoparticles produced by the polyol process present mainly the fcc metastable phase. Black-Right-Pointing-Pointer Bulk nanostructured cobalt is obtained from the nano-particles by Spark Plasma Sintering consolidation. Black-Right-Pointing-Pointer Nanotwins and stacking faults are present in every grain of the more dense sample. Black-Right-Pointing-Pointer Yield strength and plastic domain may be varied depending on the nanoparticle size and the porosity of the consolidated material.

36 MATERIALS SCIENCE↗

Evaluation of energy harvesting performance of electrostrictive polymer and carbon-filled terpolymer composites

Recent trends in energy conversion mechanisms have demonstrated the abilities of electrostrictive polymers for converting mechanical vibrations into electricity. In particular, such materials present advantageous features such as high productivity, high flexibility, and processability. Hence, the application of these materials for energy harvesting purposes has been of significant interest over the last few years. The purpose of this paper consists in evaluating the energy scavenging abilities of electrostrictive terpolymer composite filled with 1 vol % carbon black poly(vinylidene fluoride-trifluoroethylene-chlorofluoroethylene). For fair comparison, a new figure of merit taking into account the intrinsic parameters of the material is introduced. This figure of merit equals the squared product of the electric field-related electrostrictive coefficient by the Young modulus, divided by the permittivity, relating the electric energy density per cycle per squared strain magnitude and squared bias electric field. Based on this criterion, it is demonstrated that the carbon-filled terpolymer outperforms other investigated compositions, exhibiting a figure of merit as high as 30 mJ cm{sup -3} (m/m){sup -2} (V/{mu}m){sup -2} cycle{sup -1}, which is 2000 times higher than pure polyurethane. In addition, the comparison of the figure of merit with experimental maximal harvested powers shows that such a criterion allows a very accurate prediction of the energy scavenging performance of electrostrictive composites.

36 MATERIALS SCIENCE↗

First-principles study on the structure, elastic properties, hardness and electronic structure of TMB{sub 4} (TM=Cr, Re, Ru and Os) compounds

The structural formation, elastic properties, hardness and electronic structure of TMB{sub 4} (TM=Cr, Re, Ru and Os) compounds are investigated using first-principles approach. The value of C{sub 22} for these compounds is almost two times bigger than the C{sub 11} and C{sub 33}. The intrinsic hardness, shear modulus and Young's modulus are calculated to be in a sequence of CrB{sub 4}>ReB{sub 4}>RuB{sub 4}>OsB{sub 4}, and the Poisson's ratio and B/G ratio of TMB{sub 4} follow the order of CrB{sub 4} ReB{sub 4}>RuB{sub 4}>OsB{sub 4}. • The trend of hardness for TMB{sub 4} is consistent with the variation of elastic modulus. • The C{sub 22} value of TMB{sub 4} is bigger than that of C{sub 11} and C{sub 33}. • The high hardness of TMB{sub 4} is originated from the B–B bonds cage.

36 MATERIALS SCIENCE↗