Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “VOLATILE MATTER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Embedded Electronic Nose for VOC Mixture Analysis

This paper details the work done towards a low cost, small size, portable embedded electronic nose (e-nose) and its application for analysis of different VOC mixtures. The sensor array is composed of commercially available metal oxide semiconductor sensors by Figaro. The embedded E-nose consists of an ADuC831 and has an RS 232 interface for Desktop PC for higher level data collection and NN training. The ESP tool with database facility and multilayer perceptron neural network (MLP NN) is employed to interface the embedded hardware and to process the electronic nose signals before being classified. The use of embedded e-nose for the quantification of VOCs in mixtures is investigated.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Determining Outdoor CPV Cell Temperature: Preprint

An accurate method is needed for determining cell temperature when measuring CPV modules outdoors. It has been suggested that cell temperature can be calculated though a procedure that shutters sunlight to the cells while measuring the transients in open-circuit voltage (Voc) and heat sink temperature. This paper documents application of this shutter procedure to multiple CPV modules at NREL. Thechallenges and limitations are presented along with an alternate approach to measuring CPV cell operating temperature.

14 SOLAR ENERGY↗

Intrinsic Stability of Thin-Film CdS/CdTe Modules

Stability of thin-film CdTe module is crucial to the advancement of the technology. Long-term stability studies are carried out under a variety of accelerated test conditions. Accelerated-life-tests (ALT) are performed in the laboratory to accelerate degradation and hence quantify performance change in reasonably short periods of time. ALT studies attempt to simulate the conditions a solar module experiences outdoors during its lifetime, and ALT results are correlated to outdoor test results to estimate module service lifetimes, nameplate parameters, and product warranty. To accelerate degradation, laboratory experiments are often performed at elevated temperature, voltage bias and under continuous illumination. In this study laboratory size cells (0.5 cm{sup 2}), mini-modules (15 cm x 15 cm) and full-size encapsulated modules (60 cm x 120 cm) that consist of monolithically interconnected cells were subjected to different levels of illumination, elevated temperatures and electrical biases for extended periods of time. Changes in efficiency, fill-factor (FF), open-circuit voltage (Voc) and short-circuit current (Isc) as a function stress time and stress conditions are discussed.

14 SOLAR ENERGY↗

Ag Nanowire Based Transparent Conductor for CIGS PV

Coated silver nanowires (AgNW) have been considered as a replacement for transparent conducting oxides (TCOs) in CIGS based photovoltaic devices. The advantages of AgNW over TCOs are discussed, and optical and electrical characteristics of AgNWs on glass are presented. Similarly fabricated AgNWs with varying sheet resistance on CIGS devices were tested against ITO transparent conductor controls. The CIGS was produced using a roll-to-roll technique on a flexible polymer substrate. Variations in the ZnO layer resistivity that are adjacent to the AgNW layer in the CIGS device were also tested. Device results indicate similar Jsc, but a reduced FF for cells made with the AgNWs, and Voc dependence on the resistivity of the coated AgNW and ZnO window layers. FF and Voc losses associated with the use of AgNWs are discussed.

14 SOLAR ENERGY↗

Transient Response of Cadmium Telluride Modules to Light Exposure: Preprint

Commercial cadmium telluride (CdTe) photovoltaic (PV) modules from three different manufacturers were monitored for performance changes during indoor and outdoor light-exposure. Short-term transients in Voc were recorded on some modules, with characteristic times of ~1.1 hours. Outdoor performance data shows a similar drop in Voc after early morning light exposure. Preliminary analysis of FF changes show light-induced changes on multiple time scales, including a long time scale.

14 SOLAR ENERGY↗

Analysis of Solar Cell Quality Using Voltage Metrics: Preprint

The highest efficiency solar cells provide both excellent voltage and current. Of these, the open-circuit voltage (Voc) is more frequently viewed as an indicator of the material quality. However, since the Voc also depends on the band gap of the material, the difference between the band gap and the Voc is a better metric for comparing material quality of unlike materials. To take this one stepfurther, since Voc also depends on the shape of the absorption edge, we propose to use the ultimate metric: the difference between the measured Voc and the Voc calculated from the external quantum efficiency using a detailed balance approach. This metric is less sensitive to changes in cell design and definition of band gap. The paper defines how to implement this metric and demonstrates how itcan be useful in tracking improvements in Voc, especially as Voc approaches its theoretical maximum.

14 SOLAR ENERGY↗

Efficient Crystalline Si Solar Cell with Amorphous/Crystalline Silicon Heterojunction as Back Contact: Preprint

We study an amorphous/crystalline silicon heterojunction (Si HJ) as a back contact in industrial standard p-type five-inch pseudo-square wafer to replace Al back surface field (BSF) contact. The best efficiency in this study is over 17% with open-circuit (Voc) of 0.623 V, which is very similar to the control cell with Al BSF. We found that Voc has not been improved with the heterojunctionstructure in the back. The typical minority carrier lifetime of these wafers is on the order of 10 us. We also found that the doping levels of p-layer affect the FF due to conductivity and band gap shifting, and an optimized layer is identified. We conclude that an amorphous/crystalline silicon heterojunction can be a very promising structure to replace Al BSF back contact.

14 SOLAR ENERGY↗

Development of Substrate Structure CdTe Photovoltaic Devices with Performance Exceeding 10%: Preprint

Most work on CdTe-based solar cells has focused on devices with a superstrate structure. This focus is due to the early success of the superstrate structure in producing high-efficiency cells, problems of suitable ohmic contacts for lightly doped CdTe, and the simplicity of the structure for manufacturing. The development of the CdCl2 heat treatment boosted CdTe technology and perpetuated the useof the superstrate structure. However, despite the beneficial attributes of the superstrate structure, devices with a substrate structure are attractive both commercially and scientifically. The substrate structure eliminates the need for transparent superstrates and thus allows the use of flexible metal and possibly plastic substrates. From a scientific perspective, it allows better control informing the junction and direct access to the junction for detailed analysis. Research on such devices has been limited. The efficiency of these devices has been limited to around 8% due to low open-circuit voltage (Voc) and fill factor. In this paper, we present our recent device development efforts at NREL on substrate-structure CdTe devices. We have found that processing parameters requiredto fabricate high-efficiency substrate CdTe PV devices differ from those necessary for traditional superstrate CdTe devices. We have worked on a variety of contact materials including Cu-doped ZnTe and CuxTe. We will present a comparative analysis of the performance of these contacts. In addition, we have studied the influence of fabrication parameters on junction properties. We will present anoverview of our development work, which has led to CdTe devices with Voc values of more than 860 mV and NREL-confirmed efficiencies approaching 11%.

14 SOLAR ENERGY↗

Oxygen Incorporation During Fabrication of Substrate CdTe Photovoltaic Devices: Preprint

Recently, CdTe photovoltaic (PV) devices fabricated in the nonstandard substrate configuration have attracted increasing interest because of their potential compatibility with flexible substrates such as metal foils and polymer films. This compatibility could lead to the suitability of CdTe for roll-to-roll processing and building-integrated PV. Currently, however, the efficiencies of substrateCdTe devices reported in the literature are significantly lower (6%-8%) than those of high-performance superstrate devices (17%) because of significantly lower open-circuit voltage (Voc) and fill factor (FF). In our recent device development efforts, we have found that processing parameters required to fabricate high-efficiency substrate CdTe PV devices differ from those necessary fortraditional superstrate CdTe devices. Here, we investigate how oxygen incorporation in the CdTe deposition, CdCl2 heat treatment, CdS deposition, and post-deposition heat treatment affect device characteristics through their effects on the junction. By adjusting whether oxygen is incorporated during these processing steps, we have achieved Voc values greater than 860 mV and efficiencies greaterthan 10%.

14 SOLAR ENERGY↗

Estimating Persistent Mass Flux of Volatile Contaminants from the Vadose Zone to Ground Water

Contaminants may persist for long time periods within low permeability portions of the vadose zone where they cannot be effectively treated and are a potential continuing source of contamination to groundwater. Setting appropriate vadose zone remediation goals requires evaluating these persistent sources in terms of their impact on meeting groundwater remediation goals. One-dimensional approaches for estimating transport of volatile contaminants in the vadose zone are considered and compared to a one-dimensional flux-continuity-based assessment of vapor-phase contaminant movement from the vadose zone to the groundwater. The flux-continuity-based assessment demonstrates that the ability of the groundwater to move contaminant away from the water table controls the vapor-phase mass flux from the vadose zone across the water table. Limitations of the one-dimensional approaches are then discussed with respect to the need for further method development and application of two- or three-dimensional numerical modeling. The carbon tetrachloride (CT) plume at the U.S. Department of Energy Hanford Site is used as an example of a site where persistent vadose zone contamination needs to be considered in the context of groundwater remediation.

54 ENVIRONMENTAL SCIENCES↗

Effect of Hysteresis on Measurements of Thin-Film Cell Performance

Transient or hysteresis effects in polycrystalline thin film CdS/CdTe cells are a function of pre-measurement voltage bias and whether Cu is introduced as an intentional dopant during back contact fabrication. When Cu is added, the current-density (J) vs. voltage (V) measurements performed in a reverse-to-forward voltage direction will yield higher open-circuit voltage (Voc), up to 10 mV, andsmaller short-circuit current density (Jsc), by up to 2 mA/cm2, relative to scanning voltage in a forward-to-reverse direction. The variation at the maximum power point, Pmax, is however small. The resulting variation in FF can be as large as 3%. When Cu is not added, hysteresis in both Voc and Jsc is negligible however Pmax hysteresis is considerably greater. This behavior corroborates observedchanges in depletion width, Wd, derived from capacitance (C) vs voltage (V) scans. Measured values of Wd are always smaller in reverse-to-forward voltage scans, and conversely, larger in the forward-to-reverse voltage direction. Transient ion drift (TID) measurements performed on Cu-containing cells do not show ionic behavior suggesting that capacitance transients are more likely due toelectronic capture-emission processes. J-V curve simulation using Pspice shows that increased transient capacitance during light-soak stress at 100 degrees C correlates with increased space-charge recombination. Voltage-dependent collection however was not observed to increase with stress in these cells.

14 SOLAR ENERGY↗

Novel Approach for Correlating Capacitance Data with Performance During Thin-Film Device Stress Studies: Preprint

A new data mining algorithm was developed to identify the strongest correlations between capacitance data (measured between -1.5 V and +0.49 V) and 1st and 2nd level performance metrics (efficiency, open-circuit voltage (VOC), short-circuit current density (JSC), and fill-factor (FF)) during the stress testing of voltage-stabilized CdS/CdTe devices. When considering only correlations between 1stand 2nd level metrics, 96.5% of the observed variation in efficiency was attributed to FF. The overall decrease in VOC after 1000 hours of open-circuit, light-soak stress at 60 degrees C was about 1.5%. As determined by our algorithm, the most consistent correlation existing between FF and 3rd level metric capacitance data at all stages during stress testing was between FF and the apparent CdTeacceptor density (Na) calculated at a voltage of +0.49 V during forward voltage scans. Since the contribution of back contact capacitance to total capacitance increases with increasing positive voltage, this result suggests that FF degradation is associated with decreases in Na near the CdTe/back contact interface. Also of interest, it appears that capacitance data at these higher voltagesappears to more accurately fit the one-sided abrupt junction model.

14 SOLAR ENERGY↗

SU-E-T-431: Vertically-Oriented Farmer-Type Chamber for Small-Field Applications

Purpose: To introduce a non-conventional measurement setup using Farmer-type chambers to accommodate several situations of small-field dose measurements without compromising accuracy. The validation of this technique was demonstrated for photon small-field output measurements, and electron small-field percentage depth-dose (PDD) measurements. Methods: Initial chamber alignment was performed using the conventional (horizontally-oriented) chamber setup. A PDD was acquired for a 4×4 cm{sup 2} field size using this arrangement. This PDD was used as a positional reference for the vertically-oriented chamber (VOC) configuration. Next, a PDD was acquired for a 4×4 cm{sup 2} field size with the VOC. The PDD's were superimposed to find the effective shift of the VOC. Using the shifted VOC setup, photon small-field output factors were measured and compared to stereotactic diode output factor measurements. Additionally, electron smallfield PDD's were acquired using the VOC setup and results were compared to electron Monte Carlo (eMC) predictions in the Eclipse treatment planning system (TPS). Results: (1) For photon small-field output factors field-sizes 2×2 cm{sup 2} and larger, the difference between the VOC setup and SFD measurements were less than 0.8%. For field sizes less than 2×2 cm{sup 2} discrepancies ranged from 4.0 to 10.6%. (2) PDD's measured by VOC setup show better than 1.6% agreement as compared to eMC for all electron energies measured down to the 80% depth on the 2×2 cm{sup 2} PDD curve. Disagreement between the VOC setup measurement and eMC calculations for depths down to the 50% depth on the PDD curve is 3.6% or less. Conclusion: Using the VOC setup, it is possible to use a conventional farmer chamber for small field-size measurements down to 2×2 cm{sup 2} field size without sacrificing the accuracy of measurements.

60 APPLIED LIFE SCIENCES↗

High Efficiency Single Crystal CdTe Solar Cells: November 19, 2009 - January 31, 2011

The goal of the program was to develop single crystal CdTe-based top cells grown on Si solar cells as a platform for the subsequent manufacture of high efficiency tandem cells for CPV applications. The keys to both the single junction and the tandem junction cell architectures are the ability to grow high quality single-crystal CdTe and CdZnTe layers on p-type Si substrates, to dope the CdTe andCdZnTe controllably, both n and p-type, and to make low resistance ohmic front and back contacts. EPIR demonstrated the consistent MBE growth of CdTe/Si and CdZnTe/Si having high crystalline quality despite very large lattice mismatches; epitaxial CdTe/Si and CdZnTe/Si consistently showed state-of-the-art electron mobilities and good hole mobilities; bulk minority carrier recombination lifetimesof unintentionally p-doped CdTe and CdZnTe grown by MBE on Si were demonstrated to be consistently of order 100 ns or longer; desired n- and p-doping levels were achieved; solar cell series specific resistances <10 ?-cm2 were achieved; A single-junction solar cell having a state-of-the-art value of Voc and a unverified 16.4% efficiency was fabricated from CdZnTe having a 1.80 eV bandgap, idealfor the top junction in a tandem cell with a Si bottom junction.

14 SOLAR ENERGY↗

High Efficiency Organic Solar Cells: December 16, 2009 - February 2, 2011

Details on the development of novel organic solar cells incorporating Trimetasphere based acceptors are presented including: baseline performance for Lu-PCBEH acceptor blended with P3HT demonstrated at 4.89% PCE exceeding the 4.5% PCE goal; an increase of over 250mV in Voc was demonstrated for Lu-PCBEH blended with low band gap polymers compared to a comparable C60-PCBM device. The actual Voc wascertified at 260mV higher for a low band gap polymer device using the Lu-PCBEH acceptor; and the majority of the effort was focused on development of a device with over 7% PCE. While low current and fill factors suppressed overall device performance for the low band gap polymers tested, significant discoveries were made that point the way for future development of these novel acceptor materials.

14 SOLAR ENERGY↗

Process Development for High Voc CdTe Solar Cells

This is a cumulative and final report for Phases I, II and III of this NREL funded project (subcontract # XXL-5-44205-10). The main research activities of this project focused on the open-circuit voltage of the CdTe thin film solar cells. Although, thin film CdTe continues to be one of the leading materials for large-scale cost-effective production of photovoltaics, the efficiency of the CdTesolar cells have been stagnant for the last few years. This report describes and summarizes the results for this 3-year research project.

14 SOLAR ENERGY↗

Super Boiler 2 nd Generation Technology for Watertube Boilers

This report describes Phase I of a proposed two phase project to develop and demonstrate an advanced industrial watertube boiler system with the capability of reaching 94% (HHV) fuel-to-steam efficiency and emissions below 2 ppmv NO x , 2 ppmv CO, and 1 ppmv VOC on natural gas fuel. The boiler design would have the capability to produce >1500°F, >1500 psig superheated steam, burn multiple fuels, and will be 50% smaller/lighter than currently available watertube boilers of similar capacity. This project is built upon the successful Super Boiler project at GTI. In that project that employed a unique two-staged intercooled combustion system and an innovative heat recovery system to reduce NO x to below 5 ppmv and demonstrated fuel-to-steam efficiency of 94% (HHV). This project was carried out under the leadership of GTI with project partners Cleaver-Brooks, Inc., Nebraska Boiler, a Division of Cleaver-Brooks, and Media and Process Technology Inc., and project advisors Georgia Institute of Technology, Alstom Power Inc., Pacific Northwest National Laboratory and Oak Ridge National Laboratory. Phase I of efforts focused on developing 2 nd generation boiler concepts and performance modeling; incorporating multi-fuel (natural gas and oil) capabilities; assessing heat recovery, heat transfer and steam superheating approaches; and developing the overall conceptual engineering boiler design. Based on our analysis, the 2 nd generation Industrial Watertube Boiler when developed and commercialized, could potentially save 265 trillion Btu and $1.6 billion in fuel costs across U.S. industry through increased efficiency. Its ultra-clean combustion could eliminate 57,000 tons of NO x , 460,000 tons of CO, and 8.8 million tons of CO 2 annually from the atmosphere. Reduction in boiler size will bring cost-effective package boilers into a size range previously dominated by more expensive field-erected boilers, benefiting manufacturers and end users through lower capital costs.

03 NATURAL GAS↗