SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Volume VI presents the chemical benchmarks for sediment: fresh water. Consult Volume I for information on the sources.
This work compares different electrodeposition procedures to produce nickel black coatings as greener and less toxic alternatives to Cr(VI)-based coatings used in different applications. Nickel and nickel-plated brass served as substrates in studies with a Hull cell and polarization curves. After a set of comparative experiments, the best electrodeposition procedure was further studied and optimized. Optimal conditions were found with a bath consisting of 75 g/L NiCl2·6H2O + 30 g/L NaCl and a current density of 0.143 A dm−2 applied for 5 min at room temperature. Furthermore, a pre-treatment with 18.5 vol.% of hydrochloric acid in water was found to be necessary to warrant good coating adhesion to the substrate. The black color is attributed to the development of a nanostructured surface that absorbs the incident light. Corrosion testing was performed in 0.5 M NaCl aqueous solution using electrochemical impedance spectroscopy (EIS) and polarization tests.
Gas-phase experiments, using electrospray ionization quadrupole ion trap mass spectrometry (ESI-QIT/MS), were conducted to probe basic interactions of the uranyl(VI) ion, UO 2 2+ , with selected natural amino acids, namely, L-cysteine (Cys), L-histidine (His), and L-aspartic acid (Asp), which strongly bind to metal ions. The simplest amino acid, glycine (Gly), was also studied for comparison. Cys, His, and Asp have additional potentially coordinating groups beyond the amino and carboxylic acid functional groups, specifically thiol in Cys, imidazole in His, and a second carboxylate in Asp. Gas-phase experiments comprised collision-induced dissociation (CID) of uranyl–amino acid complexes and competitive CID to assess the relative binding strength of different amino acids in the same uranyl complex. Reactivity of selected uranyl–amino acid complexes with water provided further insights into relative stabilities. In positive ion mode, CID and ensuing reactions with water suggested that uranyl–neutral AA binding strength decreased in the order His > Asp > Cys > Gly, which is similar to amino acid proton affinities. In negative ion mode, CID revealed a decreasing dissociation tendency in the order Gly >> His ≈ Cys > Asp, presumably reflecting a reverse enhanced binding to uranyl of the doubly deprotonated amino acids formed in CID.
Portlandite [Ca(OH) 2 ] is a potentially dominant solid phase in the high pH fluids expected within the cementitious engineered barriers of Geological Disposal Facilities (GDF). This study combined X-ray Absorption Spectroscopy with computational modelling in order to provide atomic-scale data which improves our understanding of how a critically important radionuclide (U) will be adsorbed onto this phase under conditions relevant to a GDF environment. Such data are fundamental for predicting radionuclide mass transfer. Surface coordination chemistry and speciation of uranium with portlandite [Ca(OH) 2 ] under alkaline groundwater conditions (ca. pH 12) were determined by both in situ and ex situ grazing incidence extended X-ray absorption fine structure analysis (EXAFS) and by computational modelling at the atomic level. Free energies of sorption of aqueous uranyl hydroxides, [UO 2 (OH) n ] 2–n (n = 0–5) with the (001), (100) and (203) or (101) surfaces of portlandite are predicted from the potential of mean force using classical molecular umbrella sampling simulation methods and the structural interactions are further explored using fully periodic density functional theory computations. Although uranyl is predicted to only weakly adsorb to the (001) and (100) clean surfaces, there should be significantly stronger interactions with the (203/101) surface or at hydroxyl vacancies, both prevalent under groundwater conditions. The uranyl surface complex is typically found to include four equatorially coordinated hydroxyl ligands, forming an inner-sphere sorbate by direct interaction of a uranyl oxygen with surface calcium ions in both the (001) and (203/101) cases. In contrast, on the (100) surface, uranyl is sorbed with its axis more parallel to the surface plane. The EXAFS data are largely consistent with a surface structural layer or film similar to calcium uranate, but also show distinct uranyl characteristics, with the uranyl ion exhibiting the classic dioxygenyl oxygens at 1.8 Å and between four and five equatorial oxygen atoms at distances between 2.28 and 2.35 Å from the central U absorber. These experimental data are wholly consistent with the adsorbate configuration predicted by the computational models. These findings suggest that, under the strongly alkaline conditions of a cementitious backfill engineered barrier, there would be significant uptake of uranyl by portlandite to inhibit the mobility of U(VI) from the near field of a geological disposal facility.
This is part of NRAP phase III task efforts to share the simulation study results for Class II to Class VI well transition.
Olefin metathesis is a broadly employed reaction with applications that range from fine chemicals to materials and petrochemicals. The design and investigation of olefin metathesis catalysts have been ongoing for over half a century, with advancements made in terms of activity, stability, and selectivity. Immobilization of organometallic complexes onto solid supports such as silica or alumina is a promising strategy for catalyst heterogenization, often resulting in increased activity and stability. Consequently, a broad range of early transition metal catalysts bearing alkyl, oxide/alkoxide, and amide ligands have been grafted onto silica and their reactivities investigated. In this paper, we report a series of silica-supported tungsten and molybdenum dimers (X 3 M≡MX 3, where M = W and Mo; X = neopentyl, tert-butoxide, and dimethyl amide) and their reactivities toward catalytic olefin metathesis. Dynamic nuclear polarization (DNP)-enhanced solid-state nuclear magnetic resonance (SSNMR), diffuse reflectance infrared Fourier transform (DRIFT), UV resonance Raman, and X-ray absorption (XAS) spectroscopies suggest that upon heterogenization the dimers bind to the surface in a monopodal fashion, with the M≡M triple bond remaining intact. These structural assignments were further corroborated by density functional theory (DFT) calculations. While the homogeneous dimer counterparts are inert, the supported low-valent alkyl W and Mo dimers become active for the disproportionative self-metathesis of propylene to ethylene and butenes and 4-nonene to 4-octene and 5-decene under mild conditions. The lack of activity observed for the free and supported tert-butoxide and dimethyl amide dimers likely suggests that the neopentyl groups are necessary for the formation of a putative alkylidene active species. The difference in reactivity between the free and supported dimers could be explained either by the lowering of the activation barrier of the complex through the electronic effects of the surface or by site isolation of catalytically relevant reactive intermediates.
Topics include: SGGP Array definition basics, what is meant by the "Inner" Boundary of an array, a critical experiment with flux filter, and NRC verification of criticality calculations with UNF-ST&DARDS.
Introduction. Project OASIS is approximately 30 miles southeast of Birmingham, Alabama, and approximately 5 miles north-northwest of Alabama Power Company's Plant Gaston. Geologically, the Project area is in the Alabama fold and thrust belt province. This work builds on the initiatives of the Southeast Regional Carbon Utilization and Storage Acceleration Partnership (SECARB-USA, DE-FE0031830) that identified nearly 500 million metric tonnes of CO 2 emitted on an annual basis that is not collocated with prospective storage geology (the Coastal Plain of the Southeastern US in this context). This observation suggests costly investments in connective infrastructure (e.g., pipelines) or exploratory well drilling campaigns to identify CO 2 storage opportunities in under explored areas. While not traditionally thought of for saline storage, these studies suggest that storage prospects in the Valley and Ridge Province occur in relatively flat lying structural panels between thrust faults. For the Project OASIS region, available geologic studies related to hydrocarbon exploration suggest that Cambro-Ordovician carbonates and Cambrian clastic units offer multiple potential storage intervals, and that regional confining systems are present, such as the tectonically thickened Floyd-Parkwood Shale. The Project OASIS surface property is owned by a timber and land stewardship company, The Westervelt Company, Inc., who worked with the Project Team to select and prepare adequate sites for geologic assessment. The purpose of drilling the Westover Stratigraphic Test Well #2 was to collect geologic data to model the feasibility of commercial scale CO 2 injection and storage in an under explored region. This initiative benefits the regions emitters as the data generated from this study can inform their own internal decision making. The field program included geological and geophysical evaluations, reservoir engineering analyses, and risk assessments. This report evaluates existing data, as well as a variety of modeling scenarios to evaluate project readiness. Importantly, the impact of this study is not limited to Alabama as there are numerous large emitters throughout Appalachia, in similar geologic settings, contemplating their decarbonization options.
Abstract Benzeneperoxyseleninic acid has been proposed as the key intermediate in the widely used epoxidation of alkenes with benzeneseleninic acid and hydrogen peroxide. However, it reacts sluggishly with cyclooctene and instead rapidly decomposes in solution to a mixed selenonium–selenonate salt that was identified by X‐ray absorption and 77 Se NMR spectroscopy, as well as by single crystal X‐ray diffraction. This process includes a selenoxide elimination of the peroxyseleninic acid with liberation of oxygen and additional redox steps. The salt is relatively stable in the solid state, but generates the corresponding selenonic acid in the presence of hydrogen peroxide. The selenonic acid is inert towards cyclooctene on its own; however, rapid epoxidation occurs when hydrogen peroxide is added. This shows that the selenonic acid must first be activated through further oxidation, presumably to the heretofore unknown benzeneperoxyselenonic acid. The latter is the principal oxidant in this epoxidation.
Abstract Benzeneperoxyseleninic acid has been proposed as the key intermediate in the widely used epoxidation of alkenes with benzeneseleninic acid and hydrogen peroxide. However, it reacts sluggishly with cyclooctene and instead rapidly decomposes in solution to a mixed selenonium–selenonate salt that was identified by X‐ray absorption and 77 Se NMR spectroscopy, as well as by single crystal X‐ray diffraction. This process includes a selenoxide elimination of the peroxyseleninic acid with liberation of oxygen and additional redox steps. The salt is relatively stable in the solid state, but generates the corresponding selenonic acid in the presence of hydrogen peroxide. The selenonic acid is inert towards cyclooctene on its own; however, rapid epoxidation occurs when hydrogen peroxide is added. This shows that the selenonic acid must first be activated through further oxidation, presumably to the heretofore unknown benzeneperoxyselenonic acid. The latter is the principal oxidant in this epoxidation.
Not Available
Explore the source record for details and available documents.
Not Available
Here, the pitting resistance of SS316L, SS304, SS430, and pure Fe was studied in chloride-containing solution. Among these alloys, SS316L exhibits the highest pit initiation rate, but also the highest pitting potential. To explain this phenomenon, the maximum pit dissolution current density (i diss,max ) of the alloys in saturated pit solution was measured using one-dimensional artificial pit electrodes. A lower i diss,max was found to correlate with higher pitting and repassivation potentials. Based on a recently proposed pitting framework, a conceptual model for pitting and repassivation potentials was established, based on which the effect of i diss,max on pitting resistance was discussed.