Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Unconventional”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Power processing

Processing of electric power has been presented as a discipline that draws on almost every field of electrical engineering, including system and control theory, communications theory, electronic network design, and power component technology. The cost of power processing equipment, which often equals that of expensive, sophisticated, and unconventional sources of electrical energy, such as solar batteries, is a significant consideration in the choice of electric power systems.

Schwarz, F. C.↗
NASA NTRS1972

Exploratory development and services for preparing and examining ultrathin polished sections of lunar rocks and particulates, part 1

Development of improved procedures is reported for three classes of lunar materials: dense rocks, breccias, and particulates. High quality ultrathin sections of these materials are obtained. Lists of equipment and supplies, procedures, photomicrographic documentation, and training are provided. Advantages of ultrathin polished sections for conventional and unconventional optical microscopy methods are described. Recommendations are provided for use of ultrathin sections in lunar rock studies, for further refinement of ultrathinning procedures, and for additional training efforts to establish a capability at the Manned Space Center. For Part 2, See N72-50754.

Beauchamp, R. H.↗
NASA NTRS1972

Wind tunnel simulation of full scale vortices.

An experimental investigation has been conducted to determine the important scaling parameters for the flow in the core region of a vortex generated by a rectangular wing tip. The effect of an unconventional planform, the ogee tip, on the tip vortex is also determined. Data were measured for wing pitch angles of 6 and 9 deg at Mach numbers of 0.2, 0.5, and 0.6 for Reynolds numbers ranging from 440,000 to 7,000,000 using a triaxial hot wire probe. The probe was located at 2 and 5 chordlengths downstream from the trailing edge of the 4.25 inch and 26.0 inch chord wings. For rectangular planform wings, the measured vortex core diameter to chord ratios, peak tangential velocity ratios, and axial velocity ratios are shown to be functions only of wing lift coefficient and elapsed time from vortex formation, and appear to be independent of both Mach number and Reynolds number.

Rorke, J. B.↗
NASA NTRS1972

Space vehicle gyroscope sensor applications

Considerations which form the basis for the specification, design and evaluation of gyroscopes for spaceborne sensor applications are presented. The applications are distinguished by basic vehicle category: launch vehicles, spacecraft, entry vehicles and sounding rockets. Specifically excluded from discussion are gyroscope effector applications. Exotic or unconventional gyroscopes for which operational experience is nonexistent are mentioned only briefly to alert the reader of future trends. General requirements for testing and evaluation are discussed.

Source record↗
NASA NTRS1973

Control of turbofan lift engines for VTOL aircraft

The use of turbofan engines as lift units for VTOL aircraft poses new engine control problems. At low flight speeds, the lift units must provide the fast thrust response needed for aircraft attitude and height control. The results are presented of an analytical study of the dynamics and control of turbofan lift engines, and methods are proposed for meeting the response requirements imposed by the VTOL aircraft application. Two types of lift fan engines are discussed: the integral and remote. The integral engine is a conventional two-spool, high bypass ratio turbofan designed for low noise and short length. The remote engine employs a gas generator and a lift fan which are separated by a duct, and which need not be coaxial. For the integral engine, a control system design is presented which satisfies the VTOL response requirements. For the remote engine, two unconventional methods of control involving flow transfer between lift units are discussed. Both methods are shown to have thrust response near the required levels.

Sellers, J. F.↗
NASA NTRS1973

Wind tunnel simulation of full scale vortices

An experimental investigation has been conducted to determine the important scaling parameters for the flow in the core region of a vortex generated by a rectangular wing tip. The effect of an unconventional planform, the ogee tip, on the tip vortex is also determined. For rectangular planform wings, the measured vortex core diameter to chord ratios, peak tangential velocity ratios, and axial velocity ratios are shown to be functions only of wing lift coefficient and elapsed time from vortex formation, and appear to be independent of both Mach number and Reynolds number. The peak tangential velocities in the diffuse vortex generated by the ogee tip are only 25 percent of those in the vortex generated by the rectangular wing.

Rorke, J. B.↗
NASA NTRS1973

Progress in strapdown technology

An overview is presented of typical inertial grade instrumentation available to mechanize precision strapdown attitude reference systems as well as a novel scheme of redundancy management, if two degree of freedom instruments are used. The instrumentation is divided between conventional and unconventional sensors with some assessment of their readiness included.

Hung, J. C.↗
NASA NTRS1973

Design, fabrication, and performance of foil journal bearing for the brayton rotating unit

Foil bearings were designed and manufactured to replace pivoted-shoe journal bearings in an existing Brayton Cycle turbo-alternator-compressor. The design of this unconventional rotor support was accomplished within the constraints and space limitations imposed by the present machine, and the substitution of foil bearings was effected without changes or modification other machine components. A housing and a test rig were constructed to incorporate the new foil-bearing support into a unified assemble with an air-driven rotor and the gimbal-mounted thrust bearing, seals, and shrouds of an actual Brayton Rotating Unit. The foil bearing required no external pressure source, and stable self-acting rotation was achieved at all speeds up to 43,200 rpm. Excellent wipe-wear characteristics of the foil bearing permitted well over 1000 start-stop cycles with no deterioriation of performance in the entire speed range.

Licht, L.↗
NASA NTRS1972

Evaluation of acoustic cavities for combustion stabilization.

The stabilizing influence of acoustic cavities (quarterwave acoustic resonators) on acoustic modes of combustion instability has been studied. The ability to analytically predict cavity damping was improved. Relatively good agreement between predicted damping and measured stability was demonstrated. Full-scale motor firings were made to evaluate the influence of several parameters on stability. Results from these firings showed that stability was changed, but not dramatically, by changes in the engine operating conditions. Variations in the film-coolant flowrate do not significantly affect cavity stabilization. The ability to stabilize an engine with unconventional cavity configurations was demonstrated.

Oberg, C. L.↗
NASA NTRS1973

Control of turbofan lift engines for VTOL aircraft.

This paper presents the results of an analytical study of the dynamics and control of turbofan lift engines, and proposes methods of meeting the response requirements imposed by the VTOL aircraft application. Two types of lift fan engines are discussed: the integral and remote. The integral engine is a conventional two-spool, high bypass ratio turbofan designed for low noise and short length. The remote engine employs a gas generator and a lift fan which are separated by a duct, and which need not be coaxial. For the integral engine, a control system design is presented which satisfies the VTOL response requirements. For the remote engine, two unconventional methods of control involving flow transfer between lift units are discussed.

Sellers, J. F.↗
NASA NTRS1973

Aeronautical fuel conservation possibilities for advanced subsonic transports

The anticipated growth of air transportation is in danger of being constrained by increased prices and insecure sources of petroleum-based fuel. Fuel-conservation possibilities attainable through the application of advances in aeronautical technology to aircraft design are identified with the intent of stimulating NASA R and T and systems-study activities in the various disciplinary areas. The material includes drag reduction; weight reduction; increased efficiency of main and auxiliary power systems; unconventional air transport of cargo; and operational changes.

Braslow, A. L.↗
NASA NTRS1974

Dynamic properties of aircraft tires

A research program has investigated the use of the von Schlippe string-type tire model for predicting the dynamic behavior of aircraft tires. The transfer-function method was used for theory evaluation. A more flexible two-constant modification to the string theory tire model is presented. Experiments were conducted on four types of scale model aircraft tires. Two types were of conventional bias construction, one type was an isotropic toroid, and one type was of unbelted radial construction. The conventional string theory and model gave predictions that were in good agreement with experimental data for bias constructed tires. The two-constant modification to string theory provided better agreement between predictions and experiment for the unconventional tires. The results indicate that the string theory tire model using static and slow-rolling tire properties predicts dynamic aircraft tire properties that have the same trends as the measured dynamic properties and, in most cases, provides good quantitative agreement.

Clark, S. K.↗
NASA NTRS1975

Future long-range transports: Prospects for improved fuel efficiency

A status report is provided on current thinking concerning potential improvements in fuel efficiency and possible alternate fuels. Topics reviewed are: (1) historical trends in airplane efficiency; (2) technological opportunities including supercritical aerodynamics, (3) vortex diffusers, (4) composite materials, (5) propulsion systems, (6) active controls, and terminal-area operations; (7) unconventional design concepts, and (8) hydrogen-fueled airplane.

Nagel, A. L.↗
NASA NTRS1975

The long term energy problem and aeronautics

The projected increase in energy consumption by transportation in general and civil aviation in particular is directly opposed to the dwindling supplies of natural petroleum crude oil currently used to produce aircraft fuels. This fact dictates the need to develop even more energy conservative aircraft and propulsion systems than are currently available and to explore the potential of alternative fuels to replace the current petroleum derived hydrocarbons. Advances in technology are described in the areas of improved component efficiency, aircraft and engine integration, control systems, and advanced lightweight materials that are needed to maximize performance and minimize fuel usage. Also, improved turbofan and unconventional engine cycles which can provide significant fuel usage reductions are described. These advancements must be accomplished within expected environmental constraints such as noise and pollution limits. Alternative fuels derived from oil shale and coal are described, and the possible technological advancements needed to use these fuels in aircraft engines are discussed and evaluated with relation to potential differences in fuel characteristics.

Rudey, R. A.↗
NASA NTRS1975

Future long-range transports - Prospects for improved fuel efficiency

A status report is provided on current thinking concerning potential improvements in fuel efficiency and possible alternate fuels. Topics reviewed are: historical trends in airplane efficiency; technological opportunities including supercritical aerodynamics, vortex diffusers, composite materials, propulsion systems, active controls, and terminal-area operations; unconventional design concepts, and hydrogen-fueled airplane.

Nagel, A. L.↗
NASA NTRS1975

Thermionic topping of electric power plants

The most likely use of thermionic conversion is in the form of a topping cycle combined with a steam-turbogenerator plant. A specific reference system is chosen in which the thermionic topping cycle occurs in thermionic heat exchangers referred to as large, modular thermionic units to which heat is transferred from a separate heat source and which reject their heat to a conventional steam turboelectric system. Results of analysis show that the performance and cost criteria for practical thermionic topping of large electric power plants are well within the reach of demonstrated and foreseeable converter capabilities. Thermionic topping has many significant advantages over unconventional cycles proposed for topping applications, including level of demonstrated and projected performance and lifetime, development time, and design simplicity.

Britt, E. J.↗