Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TRACE AMOUNTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Brucite [Mg(OH2)] Carbonation in Wet Supercritical CO2: An in situ High Pressure X-Ray Diffraction Study

Understanding mechanisms and kinetics of mineral carbonation reactions relevant to sequestering carbon dioxide as a supercritical fluid (scCO2) in geologic formations is crucial to accurately predicting long-term storage risks. Most attention so far has been focused on reactions occurring between silicate minerals and rocks in the aqueous dominated CO2-bearing fluid. However, water-bearing scCO2 also comprises a reactive fluid, and in this situation mineral carbonation mechanisms are poorly understood. Using in situ high-pressure x-ray diffraction, the carbonation of brucite [Mg(OH)2] in wet scCO2 was examined at pressure (82 bar) as a function of water concentration and temperature (50 C and 75 C). Exposing brucite to anhydrous scCO2 at either temperature resulted in little or no detectable reaction over three days. However, addition of trace amounts of water resulted in partial carbonation of brucite into nesquehonite [MgCO3 3H2O] within a few hours at 50 C. By increasing water content to well above the saturation level of the scCO2, complete conversion of brucite into nesquehonite was observed. Tests conducted at 75 C resulted in the conversion of brucite into magnesite [MgCO3] instead, apparently through an intermediate nesquehonite step. Raman spectroscopy applied to brucite reacted with 18O-labeled water in scCO2 show it was incorporated into carbonate at relatively high concentration. This supports a carbonation mechanism with at least one step involving a direct reaction between the mineral and water molecules without mediation by a condensed aqueous layer.

58 GEOSCIENCES↗

Excitation-dependent multi-color emissions in Yb/Er/Eu: Gd2Ti2O7 pyrochlore for anti-counterfeiting

Highlights: • Yb/Er/Eu: Gd{sub 2}Ti{sub 2}O{sub 7} powders are prepared by a simple sol-gel method • Red emission is due to the high CR possibility of {sup 4}F{sub 7/2} + {sup 4}I{sub 11/2} → {sup 4}F{sub 9/2} + {sup 4}F{sub 9/2}. • Trace amount of Er{sup 3+} are used to reduce deleterious CR between Er{sup 3+} and Eu{sup 3+}. • Excitation-dependent multi-color emissions are achieved. • These systems are suitable for anti-counterfeiting application. - Abstract: Lanthanide ions with abundant energy levels are widely adopted to actualize controllable colorful emissions. Herein, green to red emissions are obtained in Yb/Er: Gd{sub 2}Ti{sub 2}O{sub 7} phosphor by controlling the Er{sup 3+} doping content. With further introducing Eu{sup 3+} ions, excitation-dependent multi-color emissions are achieved. The related mechanisms are investigated systematically. Our results reveal these systems with bright up- and down- conversion emissions have potential application for anti-counterfeiting.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Hall mobility in tin iodide perovskite CH{sub 3}NH{sub 3}SnI{sub 3}: Evidence for a doped semiconductor

CH{sub 3}NH{sub 3}SnI{sub 3} is a metal halide perovskite that shows metallic conductivity over a wide temperature range, although ab initio calculations and optical absorption indicate that its band structure is consistent with that of an intrinsic semiconductor. Hall effect measurements of as-grown crystals give a hole concentration of about 9×10{sup 17} cm{sup −3} with rather high Hall mobility of about 200 cm{sup 2} V{sup −1} s{sup −1} at 250 K. Artificial hole doping enhances the electrical conductivity of the crystals without influencing mobility. These observations indicate that the electronic structure in stoichiometric CH{sub 3}NH{sub 3}SnI{sub 3} can be described as that of an intrinsic semiconductor with a wide valence band. This situation leads to metal-like conduction with even a trace amount of spontaneous hole doping in the as-grown crystal. - Graphical abstract: Hall effect measurements of as-grown CH{sub 3}NH{sub 3}SnI{sub 3} crystals give a hole concentration of about 9×10{sup 17} cm{sup −3}. Artificial hole doping enhances the electrical conductivity of the crystals without influencing mobility, indicating that the electronic structure of CH{sub 3}NH{sub 3}SnI{sub 3} can be described as that of an intrinsic semiconductor with a wide valence band. Display Omitted - Highlights: • Hole concentration in highly conducting CH{sub 3}NH{sub 3}SnI{sub 3} was determined. • Hall mobility was not affected by artificial hole doping. • The electronic structure can be described as that of an intrinsic semiconductor.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Preliminary simulations of planned experiments to study the impact of trace gases on the capacity of the Weyburn-Midale field to store carbon dioxide

The CO{sub 2} stream injecting into the Weyburn-Midale field can be generally classified as a reducing stream with residual H{sub 2}S and low-molecular weight hydrocarbons. The composition of the CO{sub 2} gas stream from the Dakota Gasification Company is reported to be 95% CO{sub 2}, 4% hydrocarbons, and 1% H{sub 2}S by volume (Huxley 2006). In addition to the H{sub 2}S introduced at the injection wells, significant concentrations of H{sub 2}S are thought to have been produced in-situ by sulfate reducing bacteria from previous water floods for enhanced oil production. Produced gas compositions range in H{sub 2}S concentrations from 1 to 6 volume percent. The produced gas, including the trace impurities, is re-injected into the field. Although there is no evidence for inorganic reduction of SO{sub 4}{sup 2-} to H{sub 2}S at the Weyburn-Midale field, Sitchler and Kazuba (2009) suggest that SO{sub 4}{sup 2-} can be inorganically reduced to elemental sulfur in highly reducing environments based on a natural analog study of the Madison Formation in Wyoming. They propose that elevated concentrations of CO{sub 2} dissolve anhydrite to produce the sulfate that is then reduced. Oxidizing CO{sub 2} streams with residual O{sub 2} and SO{sub 2} typical of streams captured from oxyfuel and post combustion processes are not presently an issue at the Weyburn-Midale field. However it is possible that the oxidizing CO{sub 2} streams may be injected in the future in carbonate reservoirs similar to the Weyburn-Midale field. To date there are few modeling and experimental studies that have explored the impact of impurity gases in CO{sub 2} streams targeted for geologic storage (Gale 2009). Jacquemet et al (2009) reviewed select geochemical modeling studies that explored the impact of SO{sub 2} and H{sub 2}S impurities in the waste streams (Gunter et al., 2000, Knauss et al., 2005, Xu et al., 2007). These studies collectively show that SO{sub 2} significantly reduces the pH when oxidized to H{sub 2}SO{sub 4} causing enhanced dissolution of carbonate minerals and some sulfate mineral precipitation. Low pH results in higher mineral solubility and faster dissolution rates and is thought to enhance porosity and permeability near the injection well when trace amounts of SO{sub 2} is injected with CO{sub 2}. The impact of H{sub 2}S on storage reservoir performance appears to more subtle. Knauss et al (2005) report no significant impacts of injection of CO{sub 2} gas streams with and without H{sub 2}S (1 M Pascal H{sub 2}S + 8.4 M Pascal CO{sub 2}) in simulations of CO{sub 2} storage in the Frio sandstone formation. Geochemical reactions for H{sub 2}S impurities include enhance field alkalinity and reaction with iron bearing minerals that may delay breakthrough of H{sub 2}S relative to CO{sub 2}. Emberley et al. (2005) report that half of the alkalinity measured at monitoring wells at the Weyburn-Midale field is due to HS{sup -}. Schoonen and Xu (2004) report that H{sub 2}S can be sequestered as pyrite in sandstones and carbonates by dissolving iron hydroxides and iron-bearing clays. Similarly, Gunter et al (2000) propose the that siderite converts to iron sulfides when it is reacted with H{sub 2}S. The geochemical reactions between H{sub 2}S and iron bearing minerals together with the high solubility of H{sub 2}S relative to CO{sub 2} may contribute to the delayed break though of H{sub 2}S in experiments. A few core flood experiments have shown that the injection of supercritical CO{sub 2} into carbonate aquifers has the potential to significantly alter the porosity in the absence of trace gases such as SO{sub 2} and H{sub 2}S. Luquot and Gouze (2009) documented a 2% porosity increase in carbonate cores when rock-water interactions were transport limited and solution concentrations were closer to equilibrium and a 4% porosity increase when rock-water interactions were reaction limited and solution compositions were further from equilibrium. Similarly Le Guen et al (2007) used x-ray micro-tomography and geochemistry to show that porosity significantly increases when reacted with pure CO{sub 2}. While both of these studies nicely illustrate the relationship between reaction kinetics, thermodynamics, and porosity changes using x-ray micro-tomography, actual changes in a reservoir may be significantly lower because the input brines used in these studies were significantly dilute and below mineral carbonate saturation. The objective of the simulations reported was to explore viable experimental parameters for CO{sub 2} core flood experiments designed to investigate the impact of CO{sub 2} on porosity and permeability in the Weyburn-Midale storage reservoir. We describe the simulation results for core flood experiments in which formation waters that are equilibrated with supercritical CO{sub 2} at 60 C and 14.7 M Pascals react with three different flow units within the Midale formation.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Reactions of Ethylidene on a Model Chromia Surface: 1 1-Dichloroethane on Stoichiometric alpha-Cr2O3 (1012)

The reaction of CH{sub 3}CHCl{sub 2} over the nearly-stoichiometric {alpha}-Cr{sub 2}O{sub 3} (10{sub {bar 1}} > 2) surface produces an ethylidene intermediate that yields primarily gas phase CH{sub 2}{double_bond}CH{sub 2} and surface chlorine adatoms; however, trace amounts of HC{triple_bond}CH, CH{sub 3}CH{sub 3}, H{sub 2} and CH{sub 3}CH{double_bond}CHCH{sub 3} are also observed. A rate-limiting intramolecular isomerization (2,1-hydrogen shift) in the surface ethylidene species produces gas phase CH{sub 2}{double_bond}CH{sub 2}. The chlorine freed from the dissociation of CH{sub 3}CHCl{sub 2} binds at the five-coordinate surface Cr{sup 3+} sites on the stoichiometric surface, completing the octahedral coordination sphere, and inhibits the surface chemistry by simple site blocking. No surface carbon deposition is observed from the thermal reaction of 1,1-dichloroethane under the conditions of this study, demonstrating that the ethylidene intermediate is not a primary coke forming intermediate over (10{sub {bar 1}} > 2) facets of {alpha}-Cr{sub 2}O{sub 3} under the conditions of this study.

01 COAL, LIGNITE, AND PEAT↗

Copper substrate as a catalyst for the oxidation of chemical vapor deposition-grown graphene

We report the catalytic effect of copper substrate on graphene–oxygen reaction at high temperature. Previous studies showed that graphene grown on copper are mostly defect-free with strong oxidation resistance. We found that a freshly prepared copper-supported graphene sample can be completely oxidized in trace amount of oxygen (<3 ppm) at 600 °C within 2 h. Both X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES) suggest that upon ambient air exposure, oxygen molecules diffuse into the space between graphene and copper, resulting in the formation of copper oxide which acts as catalytic sites for the graphene-oxygen reaction. This result has important implications for the characterization, processing, and storage of copper-supported graphene samples. - Graphical abstract: The copper substrate enhances the thermel oxidation of single-layer graphene. - Highlights: • A copper-supported graphene can be oxidized in Ar (O{sub 2}<3 ppm, 600 °C, 2 h). • O{sub 2} intercalates between graphene and copper upon exposure to air. • The copper foil should not be considered as an inert substrate.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis of silica supported AuCu nanoparticle catalysts and the effects of pretreatment conditions for the CO oxidation reaction

The reaction of CH{sub 3}CHCl{sub 2} over the nearly-stoichiometric {alpha}-Cr{sub 2}O{sub 3} (10{bar 1} > 2) surface produces an ethylidene intermediate that yields primarily gas phase CH{sub 2} {double_bond} CH{sub 2} and surface chlorine adatoms; however, trace amounts of HC {triple_bond} CH, CH{sub 3}CH{sub 3}, H{sub 2} and CH{sub 3}CH {double_bond} CHCH{sub 3} are also observed. A rate-limiting intramolecular isomerization (2,1-hydrogen shift) in the surface ethylidene species produces gas phase CH{sub 2} {double_bond} CH{sub 2}. The chlorine freed from the dissociation of CH{sub 3}CHCl{sub 2} binds at the five-coordinate surface Cr{sup 3+} sites on the stoichiometric surface, completing the octahedral coordination sphere, and inhibits the surface chemistry by simple site blocking. No surface carbon deposition is observed from the thermal reaction of 1,1-dichloroethane under the conditions of this study, demonstrating that the ethylidene intermediate is not a primary coke forming intermediate over (10{bar 1} > 2) facets of {alpha}-Cr{sub 2}O{sub 3} under the conditions of this study.

01 COAL, LIGNITE, AND PEAT↗

Influences of O{sub 2} concentration on NO reduction and N{sub 2}O formation in thermal deNOx process

Flow reactor experiment and chemical kinetic modeling were carried out to evaluate the influences of oxygen concentration on NO reduction and N{sub 2}O formation during thermal deNOx process for temperatures of 1073-1473 K. Increasing oxygen concentration in the reactant gas from 0.3 to 9.3% not only reduces the NO reduction potential and N{sub 2}O emission, but also lowers and widens the ''temperature window'' for NO conversion and N{sub 2}O formation. Trace amount of impurity O{sub 2} leads to the lowest NO emission at a high temperature of 1373 K with low N{sub 2}O emission. Test reveals that high molar ratio NH{sub 3}/NO suppresses the reverse effect of oxygen and brings out high percentage of NO reduction at leaner environment. Chemical kinetic simulations using 4 detailed mechanisms display differing trends in the NO and N{sub 2}O dependence on O{sub 2} and temperature. Rota 2000 model gives the best description of our experiments, but some assumptions made in this mechanism are not fully realistic. This study provides new experimental data on the less noticed N{sub 2}O, and raises a question about the understanding of the detailed elementary chemistry on the thermal deNOx process. Further work is still required for reasonable kinetic explanations. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Neutral gas temperature estimates and metastable resonance energy transfer for argon-nitrogen discharges

Rovibrational spectroscopy band fitting of the nitrogen (N{sub 2}) second positive system is a technique used to estimate the neutral gas temperature of N{sub 2} discharges, or atomic discharges with trace amounts of a N{sub 2} added. For mixtures involving argon and N{sub 2}, resonant energy transfer between argon metastable atoms (Ar*) and N{sub 2} molecules may affect gas temperature estimates made using the second positive system. The effect of Ar* resonance energy transfer is investigated here by analyzing neutral gas temperatures of argon-N{sub 2} mixtures, for N{sub 2} percentages from 1% to 100%. Neutral gas temperature estimates are higher than expected for mixtures involving greater than 5% N{sub 2} addition, but are reasonable for argon with less than 5% N{sub 2} addition when compared with an analytic model for ion-neutral charge exchange collisional heating. Additional spatiotemporal investigations into neutral gas temperature estimates with 10% N{sub 2} addition demonstrate that although absolute temperature values may be affected by Ar* resonant energy transfer, spatiotemporal trends may still be used to accurately diagnose the discharge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Role of H2O in the Carbonation of Forsterite in Supercritical CO2

The water concentration dependence of forsterite carbonation in supercritical CO2 (scCO2) at 80°C and 76 bars was investigated by a combination of NMR, XRD, TEM and XPS. Reaction products were not detected using scCO2 alone without added H2O. When trace amounts of water were included, limited reaction was observed. Below saturation, reaction products were a mixture of partially hydrated/hydroxylated magnesium carbonates and hydroxylated silica species that were mainly in an amorphous state, forming a non-resolved layer on the forsterite surface. At water concentrations above saturation, where forsterite was in contact with both a CO2-saturated aqueous fluid and a water-saturated scCO2 fluid, solid reaction products were magnesite (MgCO3) and an amorphous polymerized SiO2 dominated by Q4, and to a lesser extent by Q3 silica coordination. Formation of these phases implies H2O initially bound in precursor hydrated/hydroxylated reaction products was liberated, inducing further reaction. Hence, for a given fluid/mineral ratio there is a water threshold above which a significant portion of the water serves in a catalytic role where more extensive carbonation reaction occurs. Defining the role of water, even in low water content environments, is therefore critical to determining the long term impact of CO2 reactivity in the subsurface.

54 ENVIRONMENTAL SCIENCES↗

X-Ray Diffraction of Slag-Based Sodium Salt Waste Forms - 15513

Cementitious materials are used to solidify and stabilize aqueous based radioactive waste containing sodium salts. The types and proportions of cementitious ingredients used to treat aqueous radioactive waste streams containing sodium salts depend on the performance objectives for the waste forms and the compositions of the waste streams. This paper documents sample preparation and x-ray diffraction results for a series of materials made with water or highly alkaline sodium salt simulated waste water and cementitious binders. The objective of this study was to: 1) generate a base line for the evolution of the waste form as a function of time and conditions, 2) design new binders based on mineralogy of the binder, 3) understand and predict anion and cation leaching behavior of contaminants of concern, and 4) predict performance of the waste forms for which phase solubility and thermodynamic data are available. Characterization of the mineralogy is also important for understanding the buffering effects that the waste form has on infiltrating water / leachates. In summary, mixtures of Type II portland cement, Grade 100 ground granulated blast furnace slag (GGBFS) and carbon burn-out (CBO) Class F Fly ash which were hydrated with water contained hydrated phase assemblages typical of those reported in the literature. The calcium silicate hydrate phase assemblage in samples hydrated with the alkaline 4.4 M sodium salt simulated waste solution was found to be a function of the (CaO + MgO) / (SiO{sub 2} + Al{sub 2}O{sub 3}) ratio of the samples characterized. No significant differences were detected in samples cured 2 months and 14 months in sealed containers at ambient indoor temperatures. Slag and a blend of slag and cement hydrated with caustic 4.4 M Na salt solution resulted in the most crystalline matrix. In addition to poorly ordered C-S-H, these samples contained fairly well ordered C-S-H I (a precursor of 14A tobermorite) and 11 A Al-substituted tobermorite. These crystalline C-S-H phases did not form or were present in only trace amounts in slag blends containing about 45 to 62 mass percent fly ash. These slag-Class F fly ash blends had a higher silica plus alumina content relative to lime and magnesia than the blends that produced C-S-H I and Al-substituted tobermorite. The calcium silicate binder in the 10:45:45 mixture of cement: slag: fly ash was made up of poorly ordered C-S-H. The sample cured for 14 months may contain a small amount of the more crystalline calcium silicate hydrate phases. Layered double hydroxides in the hydrotalcite (magnesium-aluminum carbonate hydroxide) and hydrocalumite / AFm phases (calcium aluminum hydroxide) were present in mixtures containing slag. The specific phase(s) were not identified because these phases form solid solutions and have a considerable amount of overlap in their x-ray patterns. Sodium nitrate was the only sodium salt phase identified in x-ray diffraction patterns of the samples hydrated with salt solution. Drying during x-ray diffraction sample preparation may have resulted in precipitation of the sodium nitrate or it may have been present in the samples prior to x-ray sample preparation. Sodium sulfate, aluminate, and carbonate may have been incorporated in the structures of the layered double hydroxide (AFm) type phases. These mixed metal layered double hydroxides make up an important fraction of the matrix in the slag containing blends hydrated with caustic salt solution. They are among the few oxide-based phases that exhibit substantial, permanent anion exchange capacity [Kirkpatrick, et al. 1999, Plamer, et al., 2009, and Zhang and Reardon, 2003]. They also contribute to the structural properties of cementitious matrices [Taylor, 1997]. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Advanced Water-Gas Shift Membrane Reactor

The overall objectives for this project were: (1) to identify a suitable PdCu tri-metallic alloy membrane with high stability and commercially relevant hydrogen permeation in the presence of trace amounts of carbon monoxide and sulfur; and (2) to identify and synthesize a water gas shift catalyst with a high operating life that is sulfur and chlorine tolerant at low concentrations of these impurities. This work successfully achieved the first project objective to identify a suitable PdCu tri-metallic alloy membrane composition, Pd{sub 0.47}Cu{sub 0.52}G5{sub 0.01}, that was selected based on atomistic and thermodynamic modeling alone. The second objective was partially successful in that catalysts were identified and evaluated that can withstand sulfur in high concentrations and at high pressures, but a long operating life was not achieved at the end of the project. From the limited durability testing it appears that the best catalyst, Pt-Re/Ce{sub 0.333}Zr{sub 0.333}E4{sub 0.333}O{sub 2}, is unable to maintain a long operating life at space velocities of 200,000 h{sup -1}. The reasons for the low durability do not appear to be related to the high concentrations of H{sub 2}S, but rather due to the high operating pressure and the influence the pressure has on the WGS reaction at this space velocity.

08 HYDROGEN↗

Interfacial electronic structure-modulated magnetic anisotropy in Ta/CoFeB/MgO/Ta multilayers

We have observed several unexpected phenomena when a trace amount of Fe atoms is deposited onto the CoFeB/MgO interface in Ta/CoFeB/MgO/Ta multilayers. With the nominal thickness of the introduced Fe atoms (t{sub Fe}) varying from 0 to 0.1 Å, the effective magnetic anisotropy energy (K{sub eff}) of annealed multilayers is remarkably enhanced from 1.28 × 10{sup 6 }erg/cm{sup 3} to 2.14 × 10{sup 6 }erg/cm{sup 3}. As t{sub Fe} further increasing, the K{sub eff} decreases and even becomes negative when t{sub Fe} > 1 Å, indicating the change from perpendicular magnetic anisotropy to in-plane magnetic anisotropy. The analysis by X-ray photoelectron spectrometer reveals that the Fe atoms at annealed CoFeB/MgO interface show different electronic structures as t{sub Fe} increasing, which combine with O atoms to form FeO{sub x} (x < 1), Fe{sub 2}O{sub 3}, and Fe{sub 3}O{sub 4}, respectively, leading to modulation of Fe 3d-O 2p orbital hybridization and thus the K{sub eff}. On the other hand, we find that the introduction of Fe atoms also helps to reduce the multilayers' magnetic damping.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

COSMIC ORIGINS SPECTROGRAPH OBSERVATIONS OF THE CHEMICAL COMPOSITION OF SNR LMC N132D

We present new far-ultraviolet (far-UV) spectra of an oxygen-rich knot in the Large Magellanic Cloud supernova remnant N132D, obtained with the Hubble Space Telescope (HST)-Cosmic Origins Spectrograph (COS). Moderate-resolution (DELTAv approx 200 km s{sup -1}) spectra in the HST far-UV bandpass (1150 A approx< lambda approx< 1750 A) show emission from several ionization states of oxygen as well as trace amounts of other species. We use the improvements in sensitivity and resolving power offered by COS to separate contributions from different velocity components within the remnant, as well as emission from different species within the oxygen-rich knot itself. This is the first time that compositional and velocity structure in the ultraviolet emission lines from N132D have been resolved. No nitrogen is detected in N132D, and multiple carbon species are found at velocities inconsistent with the main oxygen component. We find helium and silicon to be associated with the oxygen-rich knot and use the reddening-corrected line strengths of O III], O IV], O V, and Si IV to constrain the composition and physical characteristics of this oxygen-rich knot. We find that models with a silicon-to-oxygen abundance ratio of N(Si)/N(O) = 10{sup -2} can reproduce the observed emission for a shock velocity of approx130 km s{sup -1}, implying a mass of approx50 M {sub sun} for the N132D progenitor star.

79 ASTRONOMY AND ASTROPHYSICS↗

MATERIAL PROPERTIES OF PLUTONIUM-BEARING OXIDES STORED IN STAINLESS STEEL CONTAINERS

The destructive examination (DE) of 3013 containers after storage is part of the Surveillance and Monitoring Program based on the Department of Energy's standard for long-term storage of Pu (DOE-STD-3013). The stored, Pu-bearing materials may contain alkali halide contamination that varies from trace amounts of salt to about 50 weight percent, with smaller fractions of other compounds and oxides. These materials were characterized prior to packaging, and surveillance characterizations are conducted to determine the behavior of the materials during long term storage. The surveillance characterization results are generally in agreement with the pre-surveillance data. The predominant phases identified by X-ray diffraction are in agreement with the expected phase assemblages of the as-received materials. The measured densities are in reasonable agreement with the expected densities of materials containing the fraction of salts and actinide oxide specified by the pre-surveillance data. The radiochemical results are generally in good agreement with the pre-surveillance data for mixtures containing 'weapons grade' Pu (nominally 94% {sup 239}Pu and 6% {sup 240}Pu); however, the ICP-MS results from the present investigation generally produce lower concentrations of Pu than the pre-surveillance analyses. For mixtures containing 'fuel grade' Pu (nominally 81-93% {sup 239}Pu and 7-19% {sup 240}Pu), the ICP-MS results from the present investigation appear to be in better agreement with the pre-surveillance data than the radiochemistry results.

36 MATERIALS SCIENCE↗

Techniques For Injection Of Pre-Charaterized Dust Into The Scrape Off Layer Of Fusion Plasma

Introduction of micron-sized dust into the scrape-off layer (SOL) of a plasma has recently found many applications aimed primarily at determining dust behavior in future fusion reactors. The dust particles are typically composed of materials intrinsic to a fusion reactor. On DIII-D and TEXTOR carbon dust has been introduced into the SOL using a probe inserted from below into the divertor region. On NSTX, both Li and tungsten dust have been dropped from the top of the machine into the SOL throughout the duration of a discharge, by utilizing a vibrating piezoelectric based particle dropper. The original particle dropper was developed to inject passivated Li powder {approx} 40 {mu}m in diameter into the SOL to enhance plasma performance. A simplified version of the dropper was developed to introduce trace amounts of tungsten powder for only a few discharges, thus not requiring a large powder reservoir. The particles emit visible light from plasma interactions and can be tracked by either spectroscopic means or by fast frame rate visible cameras. This data can then be compared with dust transport codes such as DUSTT to make predictions of dust behavior in next-step devices such as ITER. For complete modeling results, it is desired to be able to inject pre-characterized dust particles in the SOL at various known poloidal locations, including near the vessel midplane. Purely mechanical methods of injecting particles are presently being studied using a modified piezoelectric-based powder dropper as a particle source and one of several piezo-based transducers to deflect the particles into the SOL. Vibrating piezo fans operating at 60 Hz with a deflection of {+-}2.5 cm can impart a significant horizontal boost in velocity. The highest injection velocities are expected from rotating paddle wheels capable of injecting particles at 10's of meters per second depending primarily on the rotation velocity and diameter of the wheel. Several injection concepts have been tested and will be discussed below.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Enhanced thermoelectric performance in zinc substituted p-type filled skutterudites CeFe{sub 4-x}Zn{sub x}Sb{sub 12}

In this study, Zn-substituted polycrystalline skutterudites CeFe{sub 4-x}Zn{sub x}Sb{sub 12} (x=0, 0.05, 0.1, 0.2, 0.3) were successfully prepared by a traditional melting-annealing method. The solubility of Zn in Fe site is {approx}1.2%, exceeding which trace amount of ZnSb phase can be detected in the XRD. This ZnSb impurity phase, with size of several hundred nanometers for the sample with x=0.2 but showing surprisingly small size of {approx}10 nm for the sample with x=0.3, selectively distributes on the grain boundaries. In particular, the introduction of Zn in Fe site effectively improves the Seebeck coefficient in a manner of enhancement in hole effective mass, but it has negligible influence on both electrical and thermal conductivities though the hole concentration is increased. Consequently the corresponding improvement in power factor leads to an improved thermoelectric figure of merit (ZT) of 0.9 at 800 K for the sample with x=0.1, which is {approx}15% higher than that of Zn-free sample. This study demonstrates a favorable effect of Zn iso-substitution and opens a new strategy to improve the thermoelectric properties of p-type Fe-based skutterudites beyond the sole phonon engineering. - Graphical abstract: (a)-(c) ZnSb nanoinclusions emerge when Zn exceeds its solubility limit. (d), (e) The introduction of Zn boosts the Seebeck coefficient and thus enhances the ZT value. Highlights: Black-Right-Pointing-Pointer Zn is successfully employed to substitute Fe atom for the first time. Black-Right-Pointing-Pointer ZnSb nanoinclusions emerge when Zn exceeds its solubility limit {approx}0.12. Black-Right-Pointing-Pointer The introduction of Zn boosts the Seebeck coefficient and enhances the ZT value.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Strategy Combining Higher Energy C-Trap Dissociation with Neutral Loss- and Product Ion-Based MS{sup n} Acquisition for Global Profiling and Structure Annotation of Fatty Acids Conjugates

Fatty acids conjugates (FACs) are ubiquitous but found in trace amounts in the natural world. They are composed of multiple unknown substructures and side chains. Thus, FACs are difficult to be analyzed by traditional mass spectrometric methods. In this study, an integrated strategy was developed to global profiling and targeted structure annotation of FACs in complex matrix by LTQ Orbitrap. Dicarboxylic acid conjugated bufotoxins (DACBs) in Venenum bufonis (VB) were used as model compounds. The new strategy (abbreviated as HPNA) combined higher-energy C-trap dissociation (HCD) with product ion- (PI), neutral loss- (NL) based MS{sup n} (n ≥ 3) acquisition in both positive-ion mode and negative-ion mode. Several advantages are presented. First, various side chains were found under HCD in negative-ion mode, which included both known and unknown side chains. Second, DACBs with multiple side chains were simultaneously detected in one run. Compared with traditional quadrupole-based mass method, it greatly increased analysis throughput. Third, the fragment ions of side chain and steroids substructure could be obtained by PI- and NL-based MS{sup n} acquisition, respectively, which greatly increased the accuracy of the structure annotation of DACBs. In all, 78 DACBs have been discovered, of which 68 were new compounds; 25 types of substructure formulas and seven dicarboxylic acid side chains were found, especially five new side chains, including two saturated dicarboxylic acids [(azelaic acid (C{sub 9}) and sebacic acid (C{sub 10})] and three unsaturated dicarboxylic acids (u-C{sub 8}, u-C{sub 9}, and u-C{sub 10}). All these results greatly enriched the structures of DACBs in VB. .

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗