SEARCH · Engineering Papers

Results for “Surface Modification and Coatings”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Promotion of oxygen reduction reaction on a double perovskite electrode by a water-induced surface modification

Highly efficient air electrodes are a key component of reversible fuel cells for energy storage and conversion; however, the development of efficient electrodes that are stable against water vapor remains a grand challenge. Here we report an air–electrode, composed of double perovskite material PrBa 0.8 Ca 0.2 Co 2 O 5+δ (PBCC) backbone coated with nanoparticles (NPs) of BaCoO 3-δ (BCO), that exhibits remarkable electrocatalytic activity for oxygen reduction reaction (ORR) while maintaining excellent tolerance to water vapor. When tested in a symmetrical cell exposed to wet air with 3 vol% H 2 O at 750 °C, the electrode shows an area specific resistance of ~0.03 Ω cm 2 in an extended period of time. The performance enhancement is attributed mainly to the electrocatalytic activity of the BCO NPs dispersed on the surface of the porous PBCC electrode. Moreover, in situ Raman spectroscopy is used to probe reaction intermediates (e.g., oxygen species) on electrode surfaces, as the electrochemical properties of the electrodes are characterized under the same conditions. The direct correlation between surface chemistry and electrochemical behavior of an electrode is vital to gaining insight into the mechanisms of the electrocatalytic processes in fuel cells and electrolysers.

25 ENERGY STORAGE↗

DOE OSTI2026

3D Tomography insights on particle-particle bonding in cold spray

The conditions of the target surface during cold spray affect deformation and bonding. While surface preparation can influence the adhesion of the first particles, such modification is not relevant to the particle-particle interfaces that dominate the growth of a coating. Here we study two-particle Cu stacks produced with a single-particle launch apparatus and compare them to single-particle experiments on a clean polished substrate. Serial cross-sectioning using microtomography permits a systematic evaluation and quantification of bonding at the particle-particle interfaces. We observe that the top particle in the two-particle stacks is much more flattened compared to single impacts on the polished substrate. Although the resulting interfacial area expansion is comparable to that of single impacts at the same velocities, bonding at the particle-particle interfaces is significantly less (never exceeding 18% even around the “optimal” velocity for bonding). Lastly, we find that hydrodynamic jetting, a form of localization known to promote adhesion in cold spray, is hindered for impacts on top of a prior particle deposition. Here, the results point to a need for future studies that separately consider topography and mechanical properties of substrates in the pursuit of optimal bonding.

Bonding↗

NASA NTRS1999

Chemical Sensors Based on IR Spectroscopy and Surface-Modified Waveguides

Sol-gel processing techniques have been used to apply thin porous films to the surfaces of planar infrared (IR) waveguides to produce widely useful chemical sensors. The thin- film coating serves to diminish the concentration of water and increase the concentration of the analyte in the region probed by the evanescent IR wave. These porous films are composed of silica, and therefore, conventional silica surface modification techniques can be used to give the surface a specific functional character. The sol-gel film was surface-modified to make the film highly hydrophobic. These sensors were shown to be capable of detecting non-polar organic analytes, such as benzonitrile, in aqueous solution with detection limits in the ppb range. Further, these porous sol-gel structures allow the analytes to diffuse into and out of the films rapidly, thus reaching equilibrium in less than ten seconds. These sensors are unique because of the fact that their operation is based on the measurement of an IR absorption spectrum. Thus, these sensors are able to identify the analytes as well as measure concentration with high sensitivity. These developments have been documented in previous reports and publications. Recently, we have also targeted detection of the polar organic molecules acetone and isopropanol in aqueous solution. Polar organics are widely used in industrial and chemical processes, hence it is of interest to monitor their presence in effluents or decontamination process flows. Although large improvements in detection limits were expected with non-polar organic molecules in aqueous solutions using very hydrophobic porous sol-gel films on silicon attenuated total reflectance (Si ATR) waveguides, it was not as clear what the detection enhancements might be for polar organic molecules. This report describes the use of modified sol-gel-coated Si ATR sensors for trace detection and quantitation of small polar organic molecules in aqueous solutions. The detection of both acetone and isopropanol molecules in aqueous solution has been previously reported for chalcogenide fiber optic sensors. The sol-gel film was produced using a mixture of ethyltriethoxysilane and tetraethoxysilane and the surface modification was carried out using trimethylchlorosilane. We have demonstrated that this film concentrates the target polar analytes from aqueous solution in the region probed by the evanescent wave to improve detection limits by as much as a factor of 450.

Lopez, Gabriel P.↗

NASA NTRS1992

Screen Cage Ion Plating (SCIP) and scratch testing of polycrystalline aluminum oxide

A screen cage ion plating (SCIP) technique was developed to apply silver films on electrically nonconducting aluminum oxide. It is shown that SCIP has remarkable throwing power; surfaces to be coated need not be in direct line of sight with the evaporation source. Scratch tests, employing a diamond stylus with a 200 micro m radius tip, were performed on uncoated and on silver coated alumina. Subsequent surface analysis show that a significant amount of silver remains on the scratched surfaces, even in areas where high stylus load produced severe crack patterns in the ceramic. Friction coefficients were lowered during the scratch tests on the coated alumina indicating that this modification of the ion planting process should be useful for applying lubricating films of soft metals to electrical insulating materials. The very good throwing power of SCIP also strongly suggests general applicability of this process in other areas of technology, e.g., electronics, in addition to tribology.

Spalvins, Talivaldis↗

NASA NTRS1962

Lubricating Properties of Ceramic-Bonded Calcium Fluoride Coatings on Nickel-Base Alloys from 75 to 1900 deg F

The endurance life and the friction coefficient of ceramic-bonded calcium fluoride (CaF2) coatings on nickel-base alloys were determined at temperatures from 75 F to 1900 F. The specimen configuration consisted of a hemispherical rider (3/16-in. rad.) sliding against the flat surface of a rotating disk. Increasing the ambient temperature (up to 1500 F) or the sliding velocity generally reduced the friction coefficient and improved coating life. Base-metal selection was critical above 1500 F. For instance, cast Inconel sliding against coated Inconel X was lubricated effectively to 1500 F, but at 1600 F severe blistering of the coatings occurred. However, good lubrication and adherence were obtained for Rene 41 sliding against coated Rene 41 at temperatures up to 1900 F; no blisters developed, coating wear life was fairly good, and the rider wear rate was significantly lower than for the unlubricated metals. Friction coefficients were 0.12 at 1500 F, 0.15 at 1700 F, and 0.17 at 1800 F and 1900 F. Because of its ready availability, Inconel X appears to be the preferred substrate alloy for applications in which the temperature does not exceed 1500 F. Rene 41 would have to be used in applications involving higher temperatures. Improved coating life was derived by either preoxidizing the substrate metals prior to the coating application or by applying a very thin (less than 0.0002 in.) burnished and sintered overlay to the surface of the coating. Preoxidation did not affect the friction coefficient. The overlay generally resulted in a higher friction coefficient than that obtained without the overlay. The combination of both modifications resulted in longer coating life and in friction coefficients intermediate between those obtained with either modification alone.

Sliney, Harold E.↗

NASA NTRS2010

Fabrication and Modification of Nanoporous Silicon Particles

Silicon-based nanoporous particles as biodegradable drug carriers are advantageous in permeation, controlled release, and targeting. The use of biodegradable nanoporous silicon and silicon dioxide, with proper surface treatments, allows sustained drug release within the target site over a period of days, or even weeks, due to selective surface coating. A variety of surface treatment protocols are available for silicon-based particles to be stabilized, functionalized, or modified as required. Coated polyethylene glycol (PEG) chains showed the effective depression of both plasma protein adsorption and cell attachment to the modified surfaces, as well as the advantage of long circulating. Porous silicon particles are micromachined by lithography. Compared to the synthesis route of the nanomaterials, the advantages include: (1) the capability to make different shapes, not only spherical particles but also square, rectangular, or ellipse cross sections, etc.; (2) the capability for very precise dimension control; (3) the capacity for porosity and pore profile control; and (4) allowance of complex surface modification. The particle patterns as small as 60 nm can be fabricated using the state-of-the-art photolithography. The pores in silicon can be fabricated by exposing the silicon in an HF/ethanol solution and then subjecting the pores to an electrical current. The size and shape of the pores inside silicon can be adjusted by the doping of the silicon, electrical current application, the composition of the electrolyte solution, and etching time. The surface of the silicon particles can be modified by many means to provide targeted delivery and on-site permanence for extended release. Multiple active agents can be co-loaded into the particles. Because the surface modification of particles can be done on wafers before the mechanical release, asymmetrical surface modification is feasible. Starting from silicon wafers, a treatment, such as KOH dipping or reactive ion etching (RIE), may be applied to make the surface rough. This helps remove the nucleation layer. A protective layer is then deposited on the wafer. The protective layer, such as silicon nitride film or photoresist film, protects the wafer from electrochemical etching in an HF-based solution. A lithography technique is applied to pattern the particles onto the protective film. The undesired area of the protective film is removed, and the protective film on the back side of the wafer is also removed. Then the pattern is exposed to HF/surfactant solution, and a larger DC electrical current is applied to the wafers for a selected time. This step removes the nucleation layer. Then a DC current is applied to generate the nanopores. Next, a large electrical current is applied to generate a release layer. The particles are mechanically suspended in the solvent and collected by filtration or centrifuge.

Ferrari, Mauro↗

DOE OSTI2022

Solution-Deposited and Patternable Conductive Polymer Thin-Film Electrodes for Microbial Bioelectronics

Microbial bioelectronic devices integrate naturally occurring or synthetically engineered electroactive microbes with microelectronics. These devices have a broad range of potential applications, but engineering the biotic–abiotic interface for biocompatibility, adhesion, electron transfer, and maximum surface area remains a challenge. Prior approaches to interface modification lack simple processability, the ability to pattern the materials, and/or a significant enhancement in currents. We report a novel conductive polymer coating that significantly enhances current densities relative to unmodified electrodes in microbial bioelectronics is reported. The coating is based on a blend of poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) crosslinked with poly(2-hydroxyethylacrylate) (PHEA) along with a thin polydopamine (PDA) layer for adhesion to an underlying indium tin oxide (ITO) electrode. When used as an interface layer with the current-producing bacterium Shewanella oneidensis MR-1, this material produces a 178-fold increase in the current density compared to unmodified electrodes, a current gain that is higher than previously reported thin-film 2D coatings and 3D conductive polymer coatings. The chemistry, morphology, and electronic properties of the coatings are characterized and the implementation of these coated electrodes for use in microbial fuel cells, multiplexed bioelectronic devices, and organic electrochemical transistor based microbial sensors are demonstrated. It is envisioned that this simple coating will advance the development of microbial bioelectronic devices.

patterned bioelectronics↗

NASA NTRS1962

LUBRICATING PROPERTIES OF CERAMIC-BONDED CALCIUM FLUORIDE COATINGS ON NICKEL-BASE ALLOYS FROM 75 DEG TO 1900 DEG F

The endurance life and the friction coefficient of ceramic-bonded calcium fluoride (CaF2) coatings on nickel-base alloys were determined at temperatures from 75° to 1900° F. The specimen configuration consisted of a hemispherical rider (3/16-in. rad.) sliding against the flat surface of a rotating disk. Increasing the ambient temperature (up to 1500° F) or the sliding velocity generally reduced the friction coefficient and improved coating life. Base-metal selection was critical above 1500° F. For instance, cast Inconel sliding against coated Inconel X was lubricated effectively to 1500° F, but at 1600° F severe blistering of the coatings occurred. However, good lubrication and adherence were obtained for René 41 sliding against coated René 41 at temperatures up to 1900° F; no blisters developed, coating wear life was fairly good, and the rider wear rate was significantly lower than for the unlubricated metals . Friction coefficients were 0.12 at 1500° F, 0.15 at 1700° F, and 0.17 at 1800° and 1900° F. Because of its ready availability, Inconel X appears to be the preferred substrate alloy for applications in which the temperature does not exceed 1500° F. René 41 would have to be used in applications involving higher temperatures. Improved coating life was derived by either preoxidizing the substrate metals prior to the coating application or by applying a very thin (<0.0002 in.) burnished and sintered overlay to the surface of the coating. Preoxidation did not affect the friction coefficient. The overlay generally resulted i n a higher friction coefficient than that obtained without the overlay. The combination of both modifications resulted in longer coating life and in friction coefficients intermediate between those obtained with either modification alone.

Nickel alloy↗

NASA NTRS1980

Process modifications for improved carbon fiber composites: Alleviation of the electrical hazards problem

Attempts to alleviate carbon-fiber-composite electrical hazards during airplane crash fires through fiber gasification are described. Thermogravimetric and differential scanning calorimetric experiments found several catalysts that caused fibers to combust when composites were exposed to test fires. Composites were tested in the 'Burn-Bang' apparatus and in high voltage electrical detection grid apparatus. In a standard three minute burn test modified composites released no fibers, while state-of-the-art composites released several hundred fiber fragments. Expected service life with and without catalytic modification was studied and electron microscopy and X-ray microanalysis furnished physical appearance and chemical composition data. An acrylic acid polymer fiber coating was developed that wet the carbon fiber surface uniformly with the catalyst, providing a marked contrast with the uneven coats obtained by solution-dipping.

Ramohalli, K.↗

NASA NTRS1990

Scattering from coated structures and antenna pattern control using impedance surfaces, part A/B

The scattering from coated, conducting structures, specifically the coated dihedral corner reflector configuration and the coated strip/plate configuration is examined. The formulation uses impedance-wedge Uniform Theory of Diffraction scattering coefficients to calculate the diffracted fields. A finite-thickness coating is approximated using the impedance boundary condition to arrive at an equivalent impedance for the coating. The formulation of the impedance wedge coefficients is outlined. Far-field, perfectly conducting approximations are discussed. Problems with the present dihedral corner reflector model for certain angles of incidence and observation are discussed along with a potentially rectifying modification. Also, the capacity to measure the electromagnetic properties of lossy materials was developed. The effects of using multiple material coatings on the radiation pattern of the horn antenna were studied. Numerous computations were devoted toward the inverse problem of synthesizing desired radiation patterns using the impedance surfaces. Stabilizing the equivalent sheet impedance using the linear control condition was attempted, and it was found to be a very difficult task.

Balanis, Constantine A.↗

DOE OSTI2020

Si-based materials for lithium-ion batteries III: Surface-modified Si/C/polyvinylidine difluoride powder

X-ray photoelectron spectroscopy was used to analyze Si/C/polyvinylidine difluoride powder obtained from Paraclete Energy Inc. The spectra were obtained using incident monochromatic Al K α radiation at 1486.6 eV (0.834 01 nm). An initial survey spectrum together with F 1s, O 1s, C 1s, and Si 2p are presented. A final survey spectrum was collected to ascertain the amount of beam-induced damage, which appears to be minimal. Finally, the spectra indicate the principal core level photoelectron and Auger electron signals with only minor nitrogen signal and show the expected silicon-carbon and silicon-fluorine species related to the surface modification process in addition to oxidized carbon and silicon due to atmospheric exposure.

25 ENERGY STORAGE↗

NASA NTRS2012

Electrospun Nanofiber Coating of Fiber Materials: A Composite Toughening Approach

Textile-based composites could significantly benefit from local toughening using nanofiber coatings. Nanofibers, thermoplastic or otherwise, can be applied to the surface of the fiber tow bundle, achieving toughening of the fiber tow contact surfaces, resulting in tougher and more damage-resistant/tolerant composite structures. The same technique could also be applied to other technologies such as tape laying, fiber placement, or filament winding operations. Other modifications to the composite properties such as thermal and electrical conductivity could be made through selection of appropriate nanofiber material. Control of the needle electric potential, precursor solution, ambient temperature, ambient humidity, airflow, etc., are used to vary the diameter and nanofiber coating morphology as needed. This method produces a product with a toughening agent applied to the fiber tow or other continuous composite precursor material where it is needed (at interfaces and boundaries) without interfering with other composite processing characteristics.

Kohlman, Lee W.↗

DOE OSTI2021

Highly Ordered Hierarchical Anodes for Extreme Fast Charging Batteries (Final Report)

The goal of this project is to enable extreme fast charging (XFC) of Li-ion batteries, which was accomplished through a combination of 1) rational design and manufacturing of hierarchically structured anode architectures; 2) blending graphite/hard carbon into a bulk hybrid anode; 3) engineering artificial solid-electrolyte interphase (SEI) coatings with reduced interphase impedance; 4) computational modeling of coupled transport, kinetic, and electrochemical phenomena; and 5) improved fundamental understanding of lithium plating through operando analysis. This work integrated structural, compositional, and surface modification of graphite anodes, multi-physics modeling of ion transport, electrochemical activity, and heat transfer, advanced strategies to detect Li plating, and semi-automated roll-to-roll cell assembly. The unique facilities at the University of Michigan (UM) and Sandia National Laboratories (SNL) were leveraged to manufacture, prototype, and characterize commercially relevant >2Ah and >180 Wh/kg cells with a target of <20% capacity fade over 500 XFC cycles.

25 ENERGY STORAGE↗

DOE OSTI2022

Enhanced Carbon Capture Behavior of Carbon Fibers via Ionic Liquid Modification

Carbon-based materials are widely deployed in carbon capture but are only limited to physisorption procedures. Further extending functionalized carbon materials to CO 2 chemisorption under low CO 2 concentration is highly desirable yet challenging. In this study, a carbon fiber composed of solely ultra-micropores (~0.45 nm) was deployed as the precursor to avoid the pore blocking effect, which was modified by superbase-derived ionic liquids (ILs) containing strong interaction sites with CO 2 . By forming a thin coating layer on the surface, the as-afforded surface-functionalized fiber materials demonstrated enhanced CO 2 uptake capacity and improved CO 2 sorption kinetics, as evaluated by both the volumetric method and thermogravimetric analysis, as well as the calculated energy distribution curves. The achievements made in this work provide guidance on the functionalization of carbon-based materials towards enhanced CO 2 chemisorption by forming a thin layer of selected IL coating.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS2019

Technology Development for the Modification of High Aspect Ratio Geometries for Thermal and Environmental Control

A key technology development driver in environmental control systems and next generation optics are discussed utilizing thin film development borrowed from the semiconductor industry. The optical and physical properties of spacecraft radiator coatings are dictated by orbital environmental conditions. For example, coatings must adequately dissipate charge buildup when orbital conditions, such as polar, geostationary or gravity neutral, result in surface charging. Current dissipation techniques include depositing a layer of ITO (indium tin oxide) on the radiator surface in a high temperature process. The application of these enhanced coatings must be such that the properties in question are tailored to mission-specific requirements. The multi-billion-dollar semiconductor industry has adopted Atomic Layer Deposition (ALD) for self-assembly and atomic-scale placement. ALD is a cost-effective nanoadditive-manufacturing technique that allows for the conformal coating of substrates with atomic control in a benign temperature and pressure environment. By using ALD, modification of these coatings can be accomplished during coating application preprocessing. The preprocessing is rendered directly on the coating dry pigment before binding. Through the introduction of paired precursor gases, thin films can be deposited on a myriad of substrates ranging from glass, polymers, aerogels, metals, powders, and other high aspect-ratio micro- and nano- structures. By providing atomic-level control, where single layers of atoms can be deposited, the fabrication of metal transparent films, precise nano-laminates, and coatings of nano-channels and pores is achievable. A method has been demonstrated for the ALD of In2O3 and films on a variety of substrates from Si(100) wafers, glass slides, and on Z93P pigments resulting in a direct spaceflight application. Results will be presented that verify the chemical composition of ALD pigments and charge dissipation properties when the pigment goes through its binding and coating process and we present early results of ALD for carbon nanotube formation and encapsulation.

Dwivedi, Vivek H.↗

NASA NTRSDate not supplied

Passive Dust Mitigation Technologies Being Developed for Demonstration Under Patch Plate Materials Compatibility Analysis Task

With the Artemis program, we are planning longer stays on the surface, with more activities that have the potential to put the astronauts and equipment in contact with greater quantities of lunar dust. The success of these missions will depend on our understanding of material interactions with lunar dust and the development of ways to mitigate dust effects in cases where exposure to dust will lead to failure of components, unacceptable loss of power or thermal control, unacceptable loss of visibility, or health issues. Passive dust mitigation by coating or surface alteration is one method that is being developed and demonstrated under the Space Technology Mission Directorate’s Game Changing Technology, Dust Mitigation Program as part of the Patch Plate Materials Compatibility Assessment Task. The goal of the task is to alter the surfaces of materials in order to passively reduce the adhesion of dust, demonstrate their performance in relevant ground-based tests using lunar simulants, and prepare them for demonstration through experiment on the lunar surface. Optically transparent, sputter deposited, work function matching coatings are being developed to reduce adhesion of dust to windows, lenses and display panels by matching the minimum energy to remove an electron from the surface to that of lunar dust in order to reduce adhesion due to charge transfer. Low surface energy coatings and surfaces for thermal control are also being developed to reduce the bonding of dust with the surface enabling it to be removed more easily. Conductive coatings with the ability to shed dust more easily are being developed for use with the active Electrodynamic Dust Shield technology to help reduce the power needed to remove dust from the surface. Passive dust mitigation surfaces for metals such as aluminum, stainless steel, and titanium are being developed that reduce the area of dust contact with the surfaces through topographical modification using laser ablation patterning to impart hierarchical topographies with nanometer to micrometer length scales in a single step. Topographically modified polymeric materials, both those with extensive space heritage and those with lower technology readiness levels, are also being evaluated. Space suit fabric surfaces that can reduce dust penetration into and through the fabric are also being investigated as well as pristine and topographically modified ceramic materials that exhibit high wear resilience. An overview of the passive dust mitigation surfaces and coatings being developed under this task, ground testing being conducted using lunar simulants, characterization techniques, and materials preparation for flight sample delivery for integration into the Alpha Space Regolith Adherence Characterization experiment going to the lunar surface on a Commercial Lunar Payload Services (CLPS) lander in 2023 will be discussed.

Lunar dust, passive mitigation, lunar simulant, co↗

DOE OSTI2026

Unlocking the Future of Aircraft Manufacturing: The Environmental Benefits of Laser Patterning for Surface Enhancement of Aircraft-Certified Alloys

Surface protection and functional modification of aircraft-certified aluminum alloys are essential for corrosion resistance, durability, and long-term airworthiness. At the same time, increasingly restrictive environmental regulations motivate the development of alternatives to legacy wet-chemical surface treatments. This study presents an integrated assessment of ultrafast femtosecond laser surface texturing as a surface functionalization approach for Aluminum 6061 alloys within an aerospace manufacturing and sustainability context. Ultrashort-pulse laser processing enables controlled micro- and nano-scale surface topographical modification with limited thermal impact, allowing adjustment of wettability and surface functionality while preserving bulk material integrity. As a dry and contactless process, femtosecond laser treatment eliminates the use of hazardous chemicals, reduces consumable inputs, and generates minimal secondary waste. A streamlined cradle-to-gate life cycle assessment conducted in accordance with ISO 14040/14044 indicates a lower global-warming potential per functional unit compared with conventional surface treatments, including anodization, plasma-assisted coatings, and organic coating systems. Complementary qualitative analyses addressing environmental health and safety, supply-chain risk, and ESG alignment indicate potential advantages related to occupational safety, regulatory compliance, waste management, and end-of-life recyclability. The investigation is performed on planar Aluminum 6061 reference surfaces with a treated area of 25 mm 2 , providing a controlled laboratory-scale basis for analyzing process behavior, functional surface modification, and associated environmental metrics. Within this defined scope, the results support further evaluation of femtosecond laser surface texturing as a surface engineering option for future aerospace manufacturing.

corrosion resistance↗

DOE OSTI2021

In-situ Investigations on Gold Nanoparticles Stabilization Mechanisms in Biological Environments Containing HSA

Nanoparticles (NPs) developments advance innovative biomedical applications. However, complex interactions and the low colloidal stability of NPs in biological media restrict their widespread utilization. The influence of NPs properties on the colloidal stability for gold NPs with 5 and 40 nm in diameter with two surface modifications, methoxy-polyethylene glycol-sulfhydryl (PEG) and citrate, in NaCl and human serum albumin (HSA) protein solution, is investigated. This study is based on small-angle X-ray scattering (SAXS) methods allowing the in-situ monitoring of interactions in physiological conditions. The PEG coating provides high colloidal stability for NPs of both sizes. For 5 nm NPs in NaCl solution, a stable 3D self-assembled body-centered cubic (BCC) arrangement is detected with an interparticle distance of 20.7 ± 0.1 nm. In protein solution, this distance increases to 21.9 ± 0.1 nm by protein penetration inside the ordered structure. For citrate-capped NPs, a different mechanism is observed. The protein particles attach to the NPs surfaces, and an appropriate concentration of proteins results in a stable suspension. Cryogenic transmission electron microscopy (Cryo-TEM), UV–visible spectroscopy, and dynamic light scattering (DLS) support the SAXS results. The findings will pave the way to design and synthesize NPs with controlled behaviors in biomedical applications.

36 MATERIALS SCIENCE↗