Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Strain improvement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Generation of ionic liquid tolerant Pseudomonas putida KT2440 strains via adaptive laboratory evolution

Although the use of ionic liquids (ILs) for the pretreatment of lignocellulosic biomass has been limited due to high costs, recent efforts to develop low-cost protic ILs show promise for achieving cost-effectiveness for biorefineries. However, an additional challenge remains in that ILs present in biomass hydrolysates are toxic to most microbial hosts, resulting in poor growth phenotypes. To address this issue, we applied an adaptive laboratory evolution (ALE) approach for tolerizing Pseudomonas putida KT2440, an industrially relevant bacterial host, to two low-cost ILs (triethanolammonium acetate [TEOH][OAc] and triethylammonium hydrogen sulfate [TEA][HS]). After continuous cultivations with gradually increased IL levels, we obtained evolved strains showing significant improvements in their growth performance under high concentrations of the ILs (maximum 4% [TEOH][OAc] and 8% [TEA][HS], in w/v) at which the wild-type strain cannot grow. Sequencing of evolved strains revealed multiple regions where mutations were associated with improved performance in minimal media conditions (relA, gacS, oprB/PP_1446, fleQ, tktA, and uvrY/PP_4100) and in IL-specific conditions (PP_5350, PP_4929/emrE, oprD, and PP_5324). We further validated the causality of the PP_5350 and emrE genes for improved IL tolerance via reverse engineering and transcriptomic analysis. Here, a common mutation in the PP_5350 gene, encoding a RpiR family transcriptional regulator, was shown to significantly upregulate the glyoxylate cycle for efficient acetate catabolism. In addition, it was suggested that the emrE gene encodes an efflux pump which can export [TEA][HS]. Finally, the cultivation of two of the best performing evolved strains with IL-treated biomass hydrolysates demonstrated their considerable potential to be used as platform strains. Taken as a whole, this work provides strains for utilization of IL-treated biomass and a mechanistic understanding that could be further leveraged to develop efficient microbial bioprocesses.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRSDate not supplied

Conformal PICA TPS– Enabling Future Nasa Planetary Science Missions

Initial development of Conformal Phenolic Impregnated Carbon Ablator (C-PICA) ablative TPS occurred under NASA’s Hypersonics Project in the 2000’s and demonstrated very low through-the-thickness thermal conductivity compared to state-of-the-art Phenolic Impregnated Carbon Ablator (PICA). PICA, which was first demonstrated on Stardust, has some inherent limitations that C-PICA improves on, primarily strain to failure. More recently C-PICA has been further matured and a family of C-PICA materials are now ready for consideration as an enabling technology for New Frontiers and other NASA missions. C-PICA has several improvements compared to PICA including: - Higher strain to failure and lower thermal conductivity (up to 55% less than PICA depending on C-PICA variant) - CTE comparable to typical composite carrier structures and also suitable for metallic substructures given high strain to failure - Temperature independent mechanical properties - Suited for single piece (up to ~ 1.5m) or tiled configurations - Larger tiles leading to reduced integration complexity compared to tiled PICA - Reduced mass compared to PICA due to reduced thermal conductivity C-PICA has been tested at heat fluxes ranging from 250-1850 W/cm^2, and shear pressures of 200Pa at 400W/cm^2 with excellent performance. Expertise on manufacturing and integration of C-PICA reside at NASA, and NASA can transition the technology to interested parties via technology transfer.

thermal protection↗
NASA NTRSDate not supplied

Conformal PICA TPS– Enabling Future Nasa Planetary Science Missions

Initial development of conformal PICA (C-PICA) ablative TPS occurred under NASA’s Hypersonics Project in the 2000’s and demonstrated very low through the thickness conductivity compared to state-of-the-art PICA. PICA, which was first demonstrated on Stardust, has some inherent limitations that C-PICA improves on, primarily strain to failure. More recently C-PICA has been further matured and a family of C-PICA materials are now ready for consideration as an enabling technology for New Frontiers and other NASA missions. C-PICA has several improvements compared to PICA including: - Higher strain to failure and lower thermal conductivity (up to 55% less than PICA depending on C-PICA variant) - CTE comparable to typical composite carrier structures - Temperature independent mechanical properties - Suited for single piece (up to ~ 1.5m) or tiled configurations - Larger tiles leading to reduced integration complexity compared to tiled PICA - Reduced mass compared to PICA due to reduced thermal conductivity C-PICA has been tested at heating fluxes ranging from 250-1850 W/cm2 with excellent performance. Based on our evaluation, multiple missions listed on the SMD Technology Showcase will potentially need a thermal protection system capable of withstanding entry environments where C-PICA is suited either as a forebody or backshell TPS. We will be highlighting mature conformal PICA variants to support the following missions at the showcase in January 2023.

thermal protection↗
DOE OSTI2021

Multiomics Data Collection, Visualization, and Utilization for Guiding Metabolic Engineering

Biology has changed radically in the past two decades, growing from a purely descriptive science into also a design science. The availability of tools that enable the precise modification of cells, as well as the ability to collect large amounts of multimodal data, open the possibility of sophisticated bioengineering to produce fuels, specialty and commodity chemicals, materials, and other renewable bioproducts. However, despite new tools and exponentially increasing data volumes, synthetic biology cannot yet fulfill its true potential due to our inability to predict the behavior of biological systems. Here, we showcase a set of computational tools that, combined, provide the ability to store, visualize, and leverage multiomics data to predict the outcome of bioengineering efforts. We show how to upload, visualize, and output multiomics data, as well as strain information, into online repositories for several isoprenol-producing strain designs. We then use these data to train machine learning algorithms that recommend new strain designs that are correctly predicted to improve isoprenol production by 23%. This demonstration is done by using synthetic data, as provided by a novel library, that can produce credible multiomics data for testing algorithms and computational tools. In short, this paper provides a step-by-step tutorial to leverage these computational tools to improve production in bioengineered strains.

09 BIOMASS FUELS↗
NASA NTRS1992

Advanced one-dimensional optical strain measurement system, phase 4

An improved version of the speckle-shift strain measurement system was developed. The system uses a two-dimensional sensor array to maintain speckle correlation in the presence of large off-axis rigid body motions. A digital signal processor (DSP) is used to calculate strains at a rate near the RS-170 camera frame rate. Strain measurements were demonstrated on small diameter wires and fibers used in composite materials research. Accurate values of Young's modulus were measured on tungsten wires, and silicon carbide and sapphire fibers. This optical technique has measured surface strains at specimen temperatures above 750 C and has shown the potential for measurements at much higher temperatures.

Lant, Christian T.↗
DOE OSTI2023

CO2 Valorization via Rewiring Carbon Metabolic Network

Energizing the world sustainably requires revolutionizing the way we harness natural resources. New renewable technologies include the microbiological upgrading of CO2, the primary greenhouse gas that causes climate change. This project aims to develop a new bioeconomy by taking up CO2 and converting it into high-value products using an autotrophic microbe. Specifically, the team constructed an acetogenic bacterium, Clostridium ljungdahlii, and developed gas fermentation processes that convert syngas (CO2/H2/CO) to the platform compound 3-hydroxybutyrate (3HB). The project has achieved several key successes, including the design and construction of 3HB genes in the gas-fermenting bacterium, the identification of a native 3HB pathway, the conversion of syngas to 3HB through strain engineering, and the improvement of the conversion through rational and iterative strain development. The optimized strain has achieved industry-relevant production rates (0.1 g/L/h) and titers (9.2 g/L), and sustained continuous gas fermentation for 3HB production for > 50 days in a bench-top gas bioreactor. The project has both industrial and scientific implications, including the exploitation of host microbes and processes to improve industrial-scale production of value-added compounds from CO2, and the promotion of gas fermentation technology. The team is also strengthening R&D synergies with other teams and industrial partners in the CO2 consortium, developing cutting-edge approaches for rapid and rational engineering of gas-fermenting hosts, and dissecting the thermodynamics and kinetics of processes for biological syngas valorization. So far, one patent application and one research article have resulted from this work, and the team anticipates additional significant outcomes from this project.

3-hydroxybutyrate↗
NASA NTRS2012

Improved Displacement Transfer Functions for Structure Deformed Shape Predictions Using Discretely Distributed Surface Strains

In the formulations of earlier Displacement Transfer Functions for structure shape predictions, the surface strain distributions, along a strain-sensing line, were represented with piecewise linear functions. To improve the shape-prediction accuracies, Improved Displacement Transfer Functions were formulated using piecewise nonlinear strain representations. Through discretization of an embedded beam (depth-wise cross section of a structure along a strain-sensing line) into multiple small domains, piecewise nonlinear functions were used to describe the surface strain distributions along the discretized embedded beam. Such piecewise approach enabled the piecewise integrations of the embedded beam curvature equations to yield slope and deflection equations in recursive forms. The resulting Improved Displacement Transfer Functions, written in summation forms, were expressed in terms of beam geometrical parameters and surface strains along the strain-sensing line. By feeding the surface strains into the Improved Displacement Transfer Functions, structural deflections could be calculated at multiple points for mapping out the overall structural deformed shapes for visual display. The shape-prediction accuracies of the Improved Displacement Transfer Functions were then examined in view of finite-element-calculated deflections using different tapered cantilever tubular beams. It was found that by using the piecewise nonlinear strain representations, the shape-prediction accuracies could be greatly improved, especially for highly-tapered cantilever tubular beams.

Ko, William L.↗
NASA NTRS1987

Analysis and test of superplastically formed titanium hat-stiffened panels under compression

Four hat-stiffened titanium panels with two different stiffener configurations were fabricated by superplastic forming/weld brazing and tested under a moderately heavy compressive load. The panels had the same overall dimensions but differed in the shape of the hat-stiffener webs; three panels had stiffeners with flat webs and the other panel had stiffeners with beaded webs. Analysis indicated that the local buckling strain of the flat stiffener web was considerably lower than the general panel buckling strain or cap buckling strain. The analysis also showed that beading the webs of the hat stiffeners removed them as the critical element for local buckling and improved the buckling strain of the panels. The analytical extensional stiffness and failure loads compared very well with experimental results.

Davis, Randall C.↗
NASA NTRS1998

Overcoats for the Improved Performance of PdCr High Temperature Thin Film Strain Gages

Overcoat protection schemes for thin film devices have typically focused on inhibiting the growth of native oxides formed on the sensor surface, rather than on improving the passivating nature of these native oxides. Here, thin sputtered Cr overcoats and heat treatments in varying oxygen partial pressures enhanced the passivating nature of native Cr203 films formed on PdCr thin film strain gages. Results of strain tests using sensors protected using this approach are presented and the implications are discussed. PdCr gages with sputtered Cr overcoats withstood 12,000 dynamic strain cycles of 1100 micro-epsilon during 100 hours of testing at a temperature of 1000 C in air. Gage factors of 1.3 with drift rates as low as 0.1 Omega/hr were achieved for devices having a nominal resistance of approximately 100 Omega's. TCR's ranging from +550 ppm/C to +798 ppm/C were realized depending on the overcoat and thermal history. Possible mechanisms for an anomaly in the electrical characteristics of these films at 800 C and improvements in stability due to the use of overcoats are presented.

Gregory, Otto J.↗
NASA NTRS2004

Implementation of Higher Order Laminate Theory Into Strain Rate Dependent Micromechanics Analysis of Polymer Matrix Composites

A procedure has been developed to investigate the nonlinear response of composite plates under large strain and high strain rate loading. A recently developed strain dependent micromechanics model is extended to account for the shear effects during impact. Four different assumptions of shear deformation effects are investigated to improve the development strain rate dependent micromechanics model. A method to determine through the thickness strain and transverse Poisson's ratio is developed. The revised micromechanics model is implemented into higher order laminate theory. Parametric studies are conducted to investigate transverse shear effects during impact.

Kim, Heung Soo↗
DOE OSTI2021

Thermal Evolution of Internal Strain in Doped PbTe

Recent improvements in the efficiency of heat-to-electricity energy conversion in lead chalcogenide thermoelectrics involve reducing the thermal conductivity by incorporating large amounts of internal strain. The extent to which typical lead chalcogenide processing techniques (such as doping, ball milling, and densification) increase internal strain and dislocation density must be quantified to improve materials design. In this study, neutron powder diffraction is leveraged to evaluate the internal strain introduced by ball milling in doped and undoped powders. Doping with Na and/or Eu increases internal strain beyond ball milling alone, with the greatest increase from combining the two dopants. Strain recovery occurs in each powder above 400 K but can be suppressed by co-doping, indicating a strong dopant–dislocation interaction in this system. Therefore, high-temperature processing of PbTe powders should be avoided if high internal strain is desired. Low-temperature densification and/or rapid pressing techniques may be key to maintaining internal strain in the final pressed pellet. The diffraction peak asymmetry and correlated elastic softening measured in pressed PbTe pellets in past studies were not observed in the precursor powders measured here, suggesting that measurements of the Debye temperature on final pressed pellets are required to examine the influence of defect-induced elastic softening on thermal conductivity. This work provides key guidance for defect engineering to maximize internal strain and thermoelectric performance in PbTe thermoelectrics.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Dual atom catalysts for rapid electrochemical reduction of CO to ethylene

Strong CO adsorption and facile CO dimerization are the key challenges in electrochemical CO2 reduction towards multi-carbon (C2+) products. We recently showed that CoPc immobilized on a single-walled carbon nanotube can selectively reduce CO2 to methanol. This is enabled through molecular strain, which dramatically improves the CO adsorption energy to CoPc, which in turn facilitates methanol formation. We now examine the extended Phthalocyanine (PcEx) dual atom catalyst (DAC), which is intrinsically strained and contains two catalyst centers, making it a candidate for reducing CO to C2+ products. Using Quantum Mechanics (QM), we screened 20 elements embedded in the PcEx, seeking catalysts with weak hydrogen binding, strong CO binding, and facile CO dimerization. We identi>ied Fe, Ru, Co, and Ir as the best performers and subsequently evaluated the entire CO to C2H4 mechanism (9 steps) using each of these elements as catalysts. In terms of limiting potential and overall exergonicity, we identi>ied CoPcEx as the best catalyst, followed by IrPcEx. We then examined the full CO to C2H4 mechanism on the bimetallic IrCoPcEx catalyst using grand canonical QM to obtain the reaction energetics as a function of applied potential. We conclude that the bimetallic IrCoPcEx is most promising for ef>iciently converting CO to ethylene.

Musgrave, Charles B.↗
NASA NTRS1993

Fiber-Optic Strain Sensors With Linear Characteristics

Fiber-optic modal domain strain sensors having linear characteristics over wide range of strains proposed. Conceived in effort to improve older fiber-optic strain sensors. Linearity obtained by appropriate choice of design parameters. Pattern of light and dark areas at output end of optical fiber produced by interference between electromagnetic modes in which laser beam propagates in fiber. Photodetector monitors intensity at one point in pattern.

Egalon, Claudio O.↗
NASA NTRS2004

Implementation of Improved Transverse Shear Calculations and Higher Order Laminate Theory Into Strain Rate Dependent Analyses of Polymer Matrix Composites

A numerical procedure has been developed to investigate the nonlinear and strain rate dependent deformation response of polymer matrix composite laminated plates under high strain rate impact loadings. A recently developed strength of materials based micromechanics model, incorporating a set of nonlinear, strain rate dependent constitutive equations for the polymer matrix, is extended to account for the transverse shear effects during impact. Four different assumptions of transverse shear deformation are investigated in order to improve the developed strain rate dependent micromechanics model. The validities of these assumptions are investigated using numerical and theoretical approaches. A method to determine through the thickness strain and transverse Poisson's ratio of the composite is developed. The revised micromechanics model is then implemented into a higher order laminated plate theory which is modified to include the effects of inelastic strains. Parametric studies are conducted to investigate the mechanical response of composite plates under high strain rate loadings. Results show the transverse shear stresses cannot be neglected in the impact problem. A significant level of strain rate dependency and material nonlinearity is found in the deformation response of representative composite specimens.

Zhu, Lin-Fa↗
NASA NTRS1997

Dynamical System Analysis of Reynolds Stress Closure Equations

In this paper, we establish the causality between the model coefficients in the standard pressure-strain correlation model and the predicted equilibrium states for homogeneous turbulence. We accomplish this by performing a comprehensive fixed point analysis of the modeled Reynolds stress and dissipation rate equations. The results from this analysis will be very useful for developing improved pressure-strain correlation models to yield observed equilibrium behavior.

Girimaji, Sharath S.↗
DOE OSTI2022

Enhancing the Phytoremediation of Heavy Metals by Combining Hyperaccumulator and Heavy Metal-Resistant Plant Growth-Promoting Bacteria

Heavy metals (HMs) have become a major environmental pollutant threatening ecosystems and human health. Although hyperaccumulators provide a viable alternative for the bioremediation of HMs, the potential of phytoremediation is often limited by the small biomass and slow growth rate of hyperaccumulators and HM toxicity to plants. Here, plant growth-promoting bacteria (PGPB)-assisted phytoremediation was used to enhance the phytoremediation of HM-contaminated soils. A PGPB with HM-tolerant (HMT-PGPB), Bacillus sp. PGP15 was isolated from the rhizosphere of a cadmium (Cd) hyperaccumulator, Solanum nigrum . Pot experiments demonstrated that inoculation with strain PGP15 could significantly increase the growth of S. nigrum . More importantly, strain PGP15 markedly improved Cd accumulation in S. nigrum while alleviating Cd-induced stress in S. nigrum . Specifically, PGP15 inoculation significantly decreased the contents of H 2 O 2 , MDA, and O 2 · − in S. nigrum , while the activities (per gram plant fresh weight) of SOD, APX, and CAT were significantly increased in the PGP15-inoculated plants compared with the control sample. These results suggested that the interactions between strain PGP15 and S. nigrum could overcome the limits of phytoremediation alone and highlighted the promising application potential of the PGPB-hyperaccumulator collaborative pattern in the bioremediation of HM-contaminated soils. Furthermore, the PGP15 genome was sequenced and compared with other strains to explore the mechanisms underlying plant growth promotion by HMT-PGPB. The results showed that core genes that define the fundamental metabolic capabilities of strain PGP15 might not be necessary for plant growth promotion. Meanwhile, PGP15-specific genes, including many transposable elements, played a crucial role in the adaptive evolution of HM resistance. Overall, our results improve the understanding of interactions between HMT-PGPB and plants and facilitate the application of HMT-PGPB in the phytoremediation of HM-contaminated soils.

Zhang, Yong↗
NASA NTRS1992

Palladium-chromium static strain gages for high temperatures

An electrical resistance strain gage that can provide accurate static strain measurement to a temperature of 1500 F or above is being developed both in fine wire and thin film forms. The gage is designed to be temperature compensated on any substrate material. It has a dual element: the gage element is a special alloy, palladium-13wt percent chromium (PdCr), and the compensator element is platinum (Pt). Earlier results of a PdCr based wire gage indicated that the apparent strain of this gage can be minimized and the repeatability of the apparent strain can be improved by prestabilizing the gage on the substrate for a long period of time. However, this kind of prestabilization is not practical in many applications and therefore the development of a wire gage which is prestabilized before installation on the substrate is desirable. This paper will present our recent progress in the development of a prestabilized wire gage which can provide meaningful strain data for the first thermal cycle. A weldable PdCr gage is also being developed for field testing where conventional flame-spraying installation can not be applied. This weldable gage is narrower than a previously reported gage, thereby allowing the gage to be more resistant to buckling under compressive loads. Some preliminary results of a prestabilized wire gage flame-sprayed directly on IN100, an engine material, and a weldable gage spot-welded on IN100 and SCS-6/(beta)21-S Titanium Matrix Composite (TMC), a National Aero-Space Plane (NASP) structure material, will be reported. Progress on the development of a weldable thin film gage will also be addressed. The measurement technique and procedures and the lead wire effect will be discussed.

Lei, Jih-Fen↗