Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solid dissolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Tank 12 Sludge Characterization and Aluminum Dissolution Demonstration

A 3-L sludge slurry sample from Tank 12 was characterized and then processed through an aluminum dissolution demonstration. The dominant constituent of the sludge was found to be aluminum in the form of boehmite. The iron content was minor, about one-tenth that of the aluminum. The salt content of the supernatant was relatively high, with a sodium concentration of {approx}7 M. Due to these characteristics, the yield stress and plastic viscosity of the unprocessed slurry were relatively high (19 Pa and 27 cP), and the settling rate of the sludge was relatively low ({approx}20% settling over a two and a half week period). Prior to performing aluminum dissolution, plutonium and gadolinium were added to the slurry to simulate receipt of plutonium waste from H-Canyon. Aluminum dissolution was performed over a 26 day period at a temperature of 65 C. Approximately 60% of the insoluble aluminum dissolved during the demonstration, with the rate of dissolution slowing significantly by the end of the demonstration period. In contrast, approximately 20% of the plutonium and less than 1% of the gadolinium partitioned to the liquid phase. However, about a third of the liquid phase plutonium became solubilized prior to the dissolution period, when the H-Canyon plutonium/gadolinium simulant was added to the Tank 12 slurry. Quantification of iron dissolution was less clear, but appeared to be on the order of 1% based on the majority of data (a minor portion of the data suggested iron dissolution could be as high as 10%). The yield stress of the post-dissolution slurry (2.5 Pa) was an order of magnitude lower than the initial slurry, due most likely to the reduced insoluble solids content caused by aluminum dissolution. In contrast, the plastic viscosity remained unchanged (27 cP). The settling rate of the post-dissolution slurry was higher than the initial slurry, but still relatively low compared to settling of typical high iron content/low salt content sludges. Approximately 40% of the post-dissolution sludge settled over a three week period. The corresponding volume of supernatant that was decanted from the waste was approximately 35% of the total waste volume. The decanted supernatant contained approximately one-third of the dissolved aluminum and exhibited a mild greenish-grey hue.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

THE SUITABILITY OF SODIUM PEROXIDE FUSION FOR PRODUCTION-SCALE PLUTONIUM PROCESSING OPERATIONS

Sodium peroxide (Na{sub 2}O{sub 2}) fusion is a method that offers significant benefits to the processing of high-fired plutonium oxide (PuO{sub 2}) materials. Those benefits include reduction in dissolution cycle time, decrease in residual solids, and reduction of the potential for generation of a flammable gas mixture during dissolution. Implementation of Na{sub 2}O{sub 2} fusion may also increase the PuO{sub 2} throughput in the HB-Line dissolving lines. To fuse a material, Na{sub 2}O{sub 2} is mixed with the feed material in a crucible and heated to 600-700 C. For low-fired and high-fired PuO{sub 2}, Na{sub 2}O{sub 2} reacts with PuO{sub 2} to form a compound that readily dissolves in ambient-temperature nitric acid without the use of potassium fluoride. The Savannah River National Laboratory (SRNL) demonstrated the feasibility of Na{sub 2}O{sub 2} fusion and subsequent dissolution for the processing of high-fired PuO{sub 2} materials in HB-Line. Testing evaluated critical dissolution characteristics and defined preliminary process parameters. Based on experimental measurements, a dissolution cycle can be complete in less than one hour, compared to the current processing time of 6-10 hours for solution heating and dissolution. Final Pu concentrations of 30-35 g/L were produced without the formation of precipitates in the final solution.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural pattern formation during liquid metal dealloying: Phase-field simulations and theoretical analyses

In recent years, liquid metal dealloying has emerged as a promising material processing method to generate micro- and nanoscale bicontinuous or porous structures. Most previous studies focused on the experimental characterization of the dealloying process and on the properties of the dealloyed materials, leaving the theoretical study incomplete to fully understand the fundamental mechanisms of the liquid metal dealloying process. In this paper, we use theoretical models and phase-field simulations to clarify the kinetics and pattern formation during liquid metal dealloying. Our investigation starts from a theoretical analysis of the 1D dissolution of a binary precursor alloy, which reveals that the 1D dissolution process involves two regimes. In the first regime, due to the low solubility of one of the elements in the melt, it accumulates at the solid-liquid interface, which reduces the dissolution kinetics. In the second regime, the interface kinetics reaches a stationary regime where both elements of the precursor alloy dissolve into the melt. Previous works revealed that in the early dealloying stage, the dealloying front is destabilized by an interfacial spinodal decomposition, which triggers the formation of interconnected ligaments. Here we extend this line of work by proposing a linear stability analysis able to predict the initial length scale of the ligaments formed in the initial stage of the dealloying. Combining this analysis with the 1D dissolution model proposed here enables us to better understand the initial conditions (composition of the precursor alloy and the melt) leading to a planar dissolution without interface destabilization. Finally, we report a strong influence of solid-state diffusion on dealloying. Although the solid-state diffusivity is four to five orders of magnitude smaller than in the liquid phase, it is found to affect both dissolution kinetics and ligament morphologies.

36 MATERIALS SCIENCE↗

Continuous optical in-situ pH monitoring during early hydration of cementitious materials

A luminescent sensor technique for pH analyses has been tested in cementitious media. The optical sensors monitor in-situ pH every 5 s during early hydration reactions over a period of 100 h from initial fluid up to consolidated stage. The pH development was analysed in calcium aluminate, calcium sulfoaluminate and OPC/slag cements up to a pH level of 13.3 and directly correlated with the heat of hydration. Thus tracing the dissolution and formation processes of solid phases via pH sensor monitoring is possible. This measurement technique enables the recording of continuous and highly reproducible pH data sets from slurries, pastes, and hardening materials leading to new vistas for individual (trans)formation pathways of solids, hydration and consolidation reactions in high alkaline cementitious systems.

36 MATERIALS SCIENCE↗

DISSOLUTION OF NEPTUNIUM OXIDE RESIDUES

This report describes the development of a dissolution flowsheet for neptunium (Np) oxide (NpO{sub 2}) residues (i.e., various NpO{sub 2} sources, HB-Line glovebox sweepings, and Savannah River National Laboratory (SRNL) thermogravimetric analysis samples). Samples of each type of materials proposed for processing were dissolved in a closed laboratory apparatus and the rate and total quantity of off-gas were measured. Samples of the off-gas were also analyzed. The quantity and type of solids remaining (when visible) were determined after post-dissolution filtration of the solution. Recommended conditions for dissolution of the NpO{sub 2} residues are: Solution Matrix and Loading: {approx}50 g Np/L (750 g Np in 15 L of dissolver solution), using 8 M nitric acid (HNO{sub 3}), 0.025 M potassium fluoride (KF) at greater than 100 C for at least 3 hours. Off-gas: Analysis of the off-gas indicated nitric oxide (NO), nitrogen dioxide (NO{sub 2}) and nitrous oxide (N{sub 2}O) as the only identified components. No hydrogen (H{sub 2}) was detected. The molar ratio of off-gas produced per mole of Np dissolved ranged from 0.25 to 0.4 moles of gas per mole of Np dissolved. A peak off-gas rate of {approx}0.1 scfm/kg bulk oxide was observed. Residual Solids: Pure NpO{sub 2} dissolved with little or no residue with the proposed flowsheet but the NpCo and both sweepings samples left visible solid residue after dissolution. For the NpCo and Part II Sweepings samples the residue amounted to {approx}1% of the initial material, but for the Part I Sweepings sample, the residue amounted to {approx}8 % of the initial material. These residues contained primarily aluminum (Al) and silicon (Si) compounds that did not completely dissolve under the flowsheet conditions. The residues from both sweepings samples contained minor amounts of plutonium (Pu) particles. Overall, the undissolved Np and Pu particles in the residues were a very small fraction of the total solids.

08 HYDROGEN↗

CO 2 utilization in built environment via the P CO 2 swing carbonation of alkaline solid wastes with different mineralogy

Carbon mineralization to solid carbonates is one of the reaction pathways that can not only utilize captured CO 2 but also potentially store it in the long term. In this study, the dissolution and carbonation behaviors of alkaline solid wastes (i.e., waste concrete) was investigated. Concrete is one of the main contributors to a large carbon emission in the built environment. Thus, the upcycling of waste concrete via CO 2 utilization has multifaceted environmental benefits including CO 2 emission reduction, waste management and reduced mining. Unlike natural silicate minerals such as olivine and serpentine, alkaline solid wastes including waste concrete are highly reactive, and thus, their dissolution and carbonation behaviors vary significantly. Here, both conventional acid (e.g., hydrochloric acid) and less studied carbonic acid (i.e., CO 2 saturated water) solvent systems were explored to extract Ca from concrete. Non-stoichiometric dissolution behaviors between Ca and Si were confirmed under far-from-equilibrium conditions (0.1 wt% slurry density), and the re-precipitation of the extracted Si was observed at near-equilibrium conditions (5 wt% slurry density), when the Ca extraction was performed at a controlled pH of 3. These experiments, with a wide range of slurry densities, provided valuable insight into Si re-precipitation phenomena and its effect on the mass transfer limitation during concrete dissolution. Next, the use of the partial pressure of CO 2 for the pH swing carbon mineralization process was investigated for concrete, and the results were compared to those of Mg-bearing silicate minerals. In the P CO 2 swing process, the extraction of Ca was significantly limited by the precipitation of the carbonate phase (i.e., calcite), since CO 2 bubbling could not provide a low enough pH condition for concrete–water–CO 2 systems. Furthermore, this study showed that the two-step carbon mineralization via P CO 2 swing, that has been developed for Mg-bearing silicate minerals, may not be viable for highly reactive Ca-bearing silicate materials (e.g., concrete). The precipitated calcium carbonate (PCC) derived from waste concrete via a pH swing process showed very promising results with a high CO 2 utilization potential as an upcycled construction material.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

ANALYSIS OF THE LEACHING EFFICIENCY OF INHIBITED WATER AND TANK SIMULANT IN REMOVING RESIDUES ON THERMOWELL PIPES

A key component for the accelerated implementation and operation of the Salt Waste Processing Facility (SWPF) is the recovery of Tank 48H. Tank 48H is a type IIIA tank with a maximum capacity of 1.3 million gallons. Video inspection of the tank showed that a film of solid material adhered to the tank internal walls and structures between 69 inch and 150 inch levels. From the video inspection, the solid film thickness was estimated to be 1mm, which corresponds to {approx}33 kg of TPB salts (as 20 wt% insoluble solids) (1). This film material is expected to be easily removed by single-rinse, slurry pump operation during Tank 48H TPB disposition via aggregation processing. A similar success was achieved for Tank 49H TPB dispositioning, with slurry pumps operating almost continuously for approximately 6 months, after which time the tank was inspected and the film was found to be removed. The major components of the Tank 49H film were soluble solids - Na{sub 3}H(CO{sub 3}){sub 2} (Hydrated Sodium Carbonate, aka: Trona), Al(OH){sub 3} (Aluminum Hydroxide, aka: Gibbsite), NaTPB (Sodium Tetraphenylborate), NaNO{sub 3} (Sodium Nitrate) and NaNO{sub 2} (Sodium Nitrite) (2). Although the Tank 48H film is expected to be primarily soluble solids, it may not behave the same as the Tank 49H film. There is a risk that material on the internal surfaces of Tank 48H could not be easily removed. As a risk mitigation activity, the chemical composition and leachability of the Tank 48H film are being evaluated prior to initiating tank aggregation. This task investigated the dissolution characteristics of Tank 48H solid film deposits in inhibited water and DWPF recycle. To this end, SRNL received four separate 23-inch long thermowell-conductivity pipe samples which were removed from the tank 48H D2 risers in order to determine: (1) the thickness of the solid film deposit, (2) the chemical composition of the film deposits, and (3) the leaching behavior of the solid film deposit in inhibited water (IW) and in DWPF recycle simulant (3).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Polymer Nanogels as Reservoirs To Inhibit Hydrophobic Drug Crystallization

Herein the effects of cross-link density and composition on the loading and in vitro dissolution of the drug phenytoin as amorphous solid dispersions in emulsion polymerized poly(N-isopropylacrylamide) (PNIPAm) and poly(N-isopropylacrylamide-co-N,N-dimethylacrylamide) nanogels were investigated near the lower critical solution temperature (LCST). Nanogel size and particle density in phosphate buffered saline were quantified by dynamic light scattering (DLS) and viscometry experiments, while drug–nanogel interactions were revealed by cross peaks in aqueous-state nuclear Overhauser effect spectroscopy measurements. Spray-dried dispersions (SDDs) of drug-loaded PNIPAm nanogel particles (R ≈ 43 nm) were directly visualized by cryogenic transmission electron microscopy and further quantified by small-angle X-ray scattering during in vitro dissolution. SDD dissolution profiles were highly dependent on the nanogel cross-link density and directly correlated with the state of dispersion of the drug-loaded nanogel particles. A balance between net particle hydrophobicity and hydrophilicity along with the distance in temperature from the LCST are shown to dictate the in vitro dissolution of the amorphous solid dispersions. Solubility enhancement mechanisms disclosed in this study provide essential guidance for the design of effective nanogels for oral drug delivery applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Graphite Steel and Chromium-Nickel Steel Corrosion: Solution Flow Through Corrosion Experiments

The corrosion of steel, when exposed to various compositions of brines is a complex, heterogeneous process involving dissolution and precipitation of multiple solids. The rate at which elements will be released from the corrosion process under these conditions will depend, in part, on effects associated with secondary alteration phases (passivating film) that may potentially form under these conditions. Understanding these processes has required the development of sophisticated methods to sample and quantitatively characterize the composition of the steel as it corrodes and releases elements. The determination of the concentrations of both brine and steel corrosion components in solutions sampled from these tests is required to fully understand the process that may eventually lead to dissolution of corrosion products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Study of autunite dissolution in the presence of Shewanella oneidensis MR1 and different bicarbonate concentrations - 15736

Remediation of uranium at Hanford Site 300 area via tripolyphosphate injections could sequester uranium (VI) in an insoluble form, creating different types of uranium phosphate minerals like autunite. The factors that influence the dissolution of such minerals come into question. Bacteria can play a significant role in the dissolution of minerals and the formation of secondary minerals. Formed autunite, as a phosphorus-containing mineral, can attract bacteria to liberate phosphorus, meeting their nutrient requirements and causing uranium release back into the environment. Previous studies have been conducted under aerobic conditions. This research was extended to investigate the stability of the autunite mineral under anaerobic conditions pertaining to the Hanford Site, and to study the effect of facultative anaerobic bacteria on the uranium (VI) release from autunite. Objectives: - Evaluate bacterial interactions with uranium (VI) by focusing on facultative anaerobic bacteria, Shewanella Oneidensis MR1. - Study the effect of bacteria on the dissolution of the uranyl phosphate solid phases created as a result of sodium tripolyphosphate injections into the subsurface at the Hanford 300 Area. - Evaluate the role of anaerobic bacteria as one of the factors affecting the outcome of environmental remediation. Experimental Approach: - 16 crimp-sealed bottles were prepared with 50 ml of media solution and 90 mg (4.4 mM of uranium VI) Ca-autunite mineral obtained from Hanford site. Bottles were inoculated with Shewanella Oneidensis MR1 strains when autunite was equilibrated with the media solutions. Bacteria was obtained from Pacific Northwestern National Laboratory (PNNL). - Solution media preparation: 20 mM NaHepes buffer: pH=7, 10 mM Lactate plus bicarbonate in four concentrations (0, 3, 5 and 10 of KHCO{sub 3}) and a bacteria-free control. Samples were taken from the supernatant solutions of the experimental and control bottles. Wet and dry digestion was performed until a white solid residue was acquired. Dilution was made on solid samples for KPA analysis to determine concentration of U (VI) as function of time. The results suggests that in the absence of HCO{sub 3}{sup -} there was a decrease in the of uranium (VI) concentration due to metal reducing bacteria Shewanella Oneidensis MR1, but for higher concentrations of HCO{sub 3}{sup -}, there is no significant difference in uranium (VI) reduction before and after inoculation with bacteria. - Although bottles were sealed, there is an hypothesis that it was oxygen restricted but not strictly performed under anaerobic conditions. For that matter there is a reason to repeat the experiment using the glove box to understand the uranium (VI) reduction mechanism and behavior of bacteria with oxic/anoxic interfaces. Conclusions: - Higher bicarbonate concentrations might interfere with uranium (VI) reduction by anaerobic bacteria. - It is necessary to reduce time of sampling before the inoculation and prolong sampling time after inoculation. - It might be necessary to increase concentration of lactate. Future Work: - Conduct experiment in strictly anaerobic conditions by using the glove box and evaluate if further reduction of uranium (VI) is obtained in the presence of carbonates (HCO{sub 3}{sup -}). - Finalize analysis of calcium and phosphorous via ICP instrument.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Disordered interfaces of alkaline aluminate salt hydrates provide glimpses of Al 3+ coordination changes

Hypothesis: The precipitation and dissolution of aluminum-bearing mineral phases in aqueous systems often proceed via changes in both aluminum coordination number and connectivity, complicating molecular-scale interpretation of the transformation mechanism. Here, the thermally induced transformation of crystalline sodium aluminum salt hydrate, a phase comprised of monomeric octahedrally coordinated aluminate which is of relevance to industrial aluminum processing, has been studied. Because intermediate aluminum coordination states during melting have not previously been detected, it is hypothesized that the transition to lower coordinated aluminum ions occurs within a highly disordered quasi-two-dimensional phase at the solid-solution interface. Experiments and simulations: In this work, in situ X-ray diffraction (XRD), Raman and 27 Al nuclear magnetic resonance (NMR) spectroscopy were used to monitor the melting transition of nonasodium aluminate hydrate (NSA, Na 9 [Al(OH) 6 ] 2 ·3(OH)·6H 2 O). A mechanistic interpretation was developed based on complementary classical molecular dynamics (CMD) simulations including enhanced sampling. A reactive forcefield was developed to bridge speciation in the solution and in the solid phase. Findings: In contrast to classical dissolution, aluminum coordination change proceeds through a dynamically stabilized ensemble of intermediate states in a disordered layer at the solid-solution interface. In both melting and dissolution of NSA, octahedral, monomeric aluminum transition through an intermediate of pentahedral coordination. The intermediate dehydroxylates to form tetrahedral aluminate (Al(OH)$_4^–$) in the liquid phase. This coordination change is concomitant with a breaking of the ionic aluminate-sodium ion linkages. The solution phase Al(OH)$_4^–$ ions subsequently polymerize into polynuclear aluminate ions. However, there are some differences between bulk melting and interfacial dissolution, with the onset of the surface-controlled process occurring at a lower temperature (~30 °C) and the coordination change taking place more gradually as a function of temperature. This work to determine the local structure and dynamics of aluminum in the disordered layer provides a new basis to understand mechanisms controlling aluminum phase transformations in highly alkaline solutions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Physics-Based Continuum Modeling for an Aqueous Rechargeable Zn/MnO 2 Battery

This study introduces a framework for modeling the aqueous Zn/MnO 2 rechargeable battery. A reaction system and a physics-based continuum model are proposed based on two reaction types, one involving insertion and the second related to dissolution and deposition of a solid reaction product. The model, fitted to empirical data, predicts voltage behavior and capacity limitations during cycling, identifying electrolytic zinc depletion as a limiting mechanism, depending on the original cell construction. The research suggests the need for further material characterization and reaction analysis, which will advance our understanding and facilitate the development of grid-scale energy storage solutions.

Electrochemistry↗

Modeling and Validation of Sodium Plugging for Heat Exchangers in Sodium-cooled Fast Reactor Systems

The project “Modeling and Validation of Sodium Plugging for Heat Exchangers in Sodium-cooled Fast Reactor Systems” was conducted jointly by Westinghouse Electric Company (Westinghouse) and Argonne National Laboratory (ANL), over the period October 1, 2013- March 31, 2016. The project’s motivation was the need to provide designers of Sodium Fast Reactors (SFRs) with a validated, state-of-the-art computational tool for the prediction of sodium oxide (Na 2 O) deposition in small-diameter sodium heat exchanger (HX) channels, such as those in the diffusion bonded HXs proposed for SFRs coupled with a supercritical CO 2 (sCO 2 ) Brayton cycle power conversion system. In SFRs, Na 2 O deposition can potentially occur following accidental air ingress in the intermediate heat transport system (IHTS) sodium and simultaneous failure of the IHTS sodium cold trap. In this scenario, oxygen can travel through the IHTS loop and reach the coldest regions, represented by the cold end of the sodium channels of the HXs, where Na 2 O precipitation may initiate and continue. In addition to deteriorating HX heat transfer and pressure drop performance, Na 2 O deposition can lead to channel plugging especially when the size of the sodium channels is small, which is the case for diffusion bonded HXs whose sodium channel hydraulic diameter is generally below 5 mm. Sodium oxide melts at a high temperature well above the sodium melting temperature such that removal of a solid plug such as through dissolution by pure sodium could take a lengthy time. The Sodium Plugging Phenomena Loop (SPPL) was developed at ANL, prior to this project, for investigating Na 2 O deposition phenomena within sodium channels that are prototypical of the diffusion bonded HX channels envisioned for SFR-sCO 2 systems. In this project, a Computational Fluid Dynamic (CFD) model capable of simulating the thermal-hydraulics of the SPPL test section and provided with Na 2 O deposition prediction capabilities, was developed. This state-of-the-art computational tool incorporates a first-principles Na 2 O deposition model developed by ANL, and combines it with predictive capabilities for the spatial and temporal variation of temperature, velocity, dissolved oxygen concentration, and wall temperature under flowing sodium conditions. The CFD model was validated under no-deposition conditions using experimental data collected with the SPPL, demonstrating the model’s capability to predict the thermal-hydraulics of the SPPL test section within the measurement uncertainty characterizing the SPPL instrumentation. The model’s deposition prediction capability was not, however, validated as the SPPL could not be operated under plugging conditions during the project, resulting in the lack of deposition data with adequate pedigree for a CFD model validation. Two novel diagnostic techniques to detect and characterize Na 2 O deposits, i.e. Ultrasonic Time Domain Reflectometry (UTDR) and Potential Drop (PD) techniques, were developed to ultimately assist in the validation effort under plugging conditions, which can be performed once the SPPL becomes operational. This development effort consisted first in demonstrating, analytically and/or computationally, the capability of these techniques to diagnose Na 2 O deposits inside of small channels (particularly the deposit’s thickness), and subsequently in the fabrication and testing of prototypical UTDR and PD instrumentation. The testing, performed on mockups of the SPPL test section, demonstrated the capability of these techniques to detect and characterize material discontinuities like those induced by sodium oxide deposition on stainless steel channel walls. Because of the mentioned impossibility to run the SPPL in a plugging mode, the developed instrumentation could not be tested in-situ, i.e. at the SPPL while deposits are being formed inside of the SPPL test section. Recommended future work includes a possible enhancement in the CFD modeling technique and installation of the developed UTDR and PD instrumentation on the test section, followed by plugging tests to be conducted with the SPPL. The installation of the UTDR and PD diagnostic instrumentation on the SPPL test section will allow collection of Na 2 O deposition data after the onset of deposition to nearly complete channel plugging, which can ultimately be used for the validation of the CFD model.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Advances in the Glass Formulations for the Hanford Tank Waste Treatment and Immobilization Plant

The Department of Energy-Office of River Protection (DOE-ORP) is constructing the Hanford Tank Waste Treatment and Immobilization Plant (WTP) to treat radioactive waste currently stored in underground tanks at the Hanford site in Washington. The WTP that is being designed and constructed by a team led by Bechtel National, Inc. (BNI) will separate the tank waste into High Level Waste (HLW) and Low Activity Waste (LAW) fractions with the majority of the mass (~90%) directed to LAW and most of the activity (>95%) directed to HLW. The pretreatment process, envisioned in the baseline, involves the dissolution of aluminum-bearing solids so as to allow the aluminum salts to be processed through the cesium ion exchange and report to the LAW Facility. There is an oxidative leaching process to affect a similar outcome for chromium-bearing wastes. Both of these unit operations were advanced to accommodate shortcomings in glass formulation for HLW inventories. A by-product of this are a series of technical challenges placed upon materials selected for the processing vessels. The advances in glass formulation play a role in revisiting the flow sheet for the WTP and hence, the unit operations that were being imposed by minimal waste loading requirements set forth in the contract for the design and construction of the plant. Another significant consideration to the most recent revision of the glass models are the impacts on resolution of technical questions associated with current efforts for design completion.

Kruger, Albert A.↗

Advances in the glass formulations for the Hanford Tank Waste Treatment and Immobilization Plant - 15053

The Department of Energy-Office of River Protection (DOE-ORP) is constructing the Hanford Tank Waste Treatment and Immobilization Plant (WTP) to treat radioactive waste currently stored in underground tanks at the Hanford site in Washington. The WTP that is being designed and constructed by a team led by Bechtel National, Inc. (BNI) will separate the tank waste into High Level Waste (HLW) and Low Activity Waste (LAW) fractions with the majority of the mass (∼90%) directed to LAW and most of the activity (>95%) directed to HLW. The pretreatment process, envisioned in the baseline, involves the dissolution of aluminum-bearing solids so as to allow the aluminum salts to be processed through the cesium ion exchange and report to the LAW Facility. There is an oxidative leaching process to affect a similar outcome for chromium-bearing wastes. Both of these unit operations were advanced to accommodate shortcomings in glass formulation for HLW inventories. A by-product of this are a series of technical challenges placed upon materials selected for the processing vessels. The advances in glass formulation play a role in revisiting the flow sheet for the WTP and hence, the unit operations that were being imposed by minimal waste loading requirements set forth in the contract for the design and construction of the plant. Another significant consideration to the most recent revision of the glass models are the impacts on resolution of technical questions associated with current efforts for design completion. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Manipulating Interfacial Dissolution–Redeposition Dynamics to Resynthesize Electrode Surface Chemistry

The solid-liquid electrochemical interface offers a two-dimensional environment for geometrically confined interfacial reactions to tailor electrode surface chemistry under operating conditions. In this study, we demonstrate that the dissolution and redeposition kinetics of transition metal cations, a ubiquitous phenomenon at the electrochemical interface, can be manipulated to regulate the chemical composition and crystal structure of the electrode surface as well as the overall electrochemical performance. Foreign cations (e.g., Ti 4+ ), either added as electrolyte additives or dissolved from surface coatings, can rapidly participate in the electrode dissolution-redeposition process, and facilitate the establishment of the dissolution-redeposition equilibrium. Our work expands the control over the electrochemical reactions at the solid-liquid interface and provides new insights into interfacial studies in electrochemistry and surface science.

25 ENERGY STORAGE↗

Chloride substitution in sodium borohydride

The dissolution of sodium chloride and sodium borohydride into each other resulting in formation of solid solutions of composition Na(BH{sub 4}){sub 1-x}Cl{sub x} is studied. The dissolution reaction is facilitated by two methods: ball milling or combination of ball milling and annealing at 300 deg. C for three days of NaBH{sub 4}-NaCl samples in molar ratios of 0.5:0.5 and 0.75:0.25. The degree of dissolution is studied by Rietveld refinement of synchrotron radiation powder X-ray diffraction (SR-PXD) data. The results show that dissolution of 10 mol% NaCl into NaBH{sub 4}, forming Na(BH{sub 4}){sub 0.9}Cl{sub 0.1}, takes place during ball milling. A higher degree of dissolution of NaCl in NaBH{sub 4} is obtained by annealing resulting in solid solutions containing up to 57 mol% NaCl, i.e. Na(BH{sub 4}){sub 0.43}Cl{sub 0.57}. In addition, annealing results in dissolution of 10-20 mol% NaBH{sub 4} into NaCl. The mechanism of the dissolution during annealing and the decomposition pathway of the solid solutions are studied by in situ SR-PXD. Furthermore, the stability upon hydrogen release and uptake were studied by Sieverts measurements. - Graphical Abstract: Dissolution of sodium chloride and sodium borohydride into each other resulting in formation of solid solutions of composition Na(BH{sub 4}){sub 1-x}Cl{sub x} is studied. Dissolution is facilitated by two methods: ball milling or annealing at 300 deg. C for three days of NaBH{sub 4}-NaCl samples. Sample compositions and dissolution mechanism are studied by Rietveld refinement of synchrotron radiation powder X-ray diffraction data. Highlights: > Studies of dissolution of sodium chloride and sodium borohydride into each other. > Solid state diffusion facilitated by mechanical and thermal treatments. > Dissolution is more efficiently induced by heating than by mechanical treatment. > Mechanism for dissolution studied by Rietveld refinement of in situ SR-PXD data.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of Irradiation on Strengthening of a Model Fe-9Cr Oxide Dispersion Strengthened Alloy

The growing energy demand will increasingly call upon advanced nuclear reactors to supply safe and reliable energy worldwide. However, structural and cladding materials in these reactors will be subject to extreme conditions of up to a few hundred displacements per atom (dpa) at temperatures as high as 600 deg. C. Oxide dispersion strengthened (ODS) alloys are leading candidates for these components because their dispersion of Y-Ti-O nanoclusters provides high strength at elevated temperatures and dimensional stability under irradiation. But recent work has suggested that the oxides are unstable under irradiation, which has serious implications on mechanical performance. Thus, the objective of this work is to understand the change in strengthening mechanisms of an Fe-9Cr ODS alloy under irradiation. We use two approaches to assess strengthening of a proton-irradiated and neutron-irradiated Fe-9Cr ODS. First, nanoindentation directly measures changes in yield strength. Second, microstructure measurements are passed through models of two strengthening mechanisms. Results of these two approaches are compared to infer the strengthening mechanisms in the irradiated ODS alloy. A model Fe-9Cr ODS steel was irradiated to 3 dpa at 500 deg. C using either 2.0 MeV protons or a fast neutron spectrum. Both irradiation types induced the formation of dislocation loops and voids. Both proton and neutron irradiation resulted in dissolution of oxide nanoclusters, though neutron irradiation led to much more extensive oxide nano-cluster dissolution. The irradiated microstructure was used to predict irradiation hardening by considering both the precipitation strengthening and solid solution strengthening mechanisms. Due to more extensive oxide nano-cluster dissolution under neutron irradiation, the solid solution strengthening mechanism must be considered in order for the predicted change in yield strength to be comparable to that measured by nanoindentation. (authors)

36 MATERIALS SCIENCE↗