Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solid dissolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Tracer Film Growth Study of the Corrosion of Magnesium Alloys AZ31B and ZE10A in 0.01% NaCl Solution

We conducted a sequential isotopic tracer study of corrosion film growth for Mg-3Al-1Zn-0.25Mn (AZ31B) and Mg-1.2Zn-0.25Zr-<0.5Nd (ZE10A) by 4 h immersion in H 2 18 O or D 2 16 O, followed by a 20 h immersion in a 0.01 wt% NaCl H 2 18 O or D 2 16 O solution. Sputter depth profiles were obtained for 16 O, 18 O, H, and D using secondary ion mass spectrometry (SIMS). When compared to the previous tracer study for these alloys in salt-free water, the addition of 0.01 wt% NaCl resulted in a transition from oxygen inward-dominated film growth to a component of mixed inward/outward film growth for both alloys. The hydrogen tracer behavior remained inward growing for AZ31B, and short-circuit, inward growing for ZE10A, in both pure water and in 0.01 wt% NaCl solution, with extensive penetration of D beyond the film and into the underlying alloy also observed for ZE10A. Our analysis of the films by X-ray photoelectron spectroscopy (XPS) and cross-section scanning transmission electron microscopy (STEM) indicated intermixed Mg(OH) 2 and MgO, with the relative fraction of Mg(OH) 2 peaking near the center of the film. These findings suggest a decoupled film growth mechanism, with initial formation of oxide followed by NaCl-accelerated conversion to hydroxide, likely by both solid-state and dissolution-precipitation processes.

36 MATERIALS SCIENCE↗

Subsurface Uranium Fate and Transport: Integrated Experiments and Modeling of Coupled Biogeochemical Mechanisms of Nanocrystalline Uraninite Oxidation by Fe(III)-(hydr)oxides - Project Final Report

Subsurface bacteria including sulfate reducing bacteria (SRB) reduce soluble U(VI) to insoluble U(IV) with subsequent precipitation of UO 2 . We have shown that SRB reduce U(VI) to nanometer-sized UO 2 particles (1-5 nm) which are both intra- and extracellular, with UO 2 inside the cell likely physically shielded from subsequent oxidation processes. We evaluated the UO 2 nanoparticles produced by Desulfovibrio desulfuricans G20 under growth and non-growth conditions in the presence of lactate or pyruvate and sulfate, thiosulfate, or fumarate, using ultrafiltration and HR-TEM. Results showed that a significant mass fraction of bioreduced U (35-60%) existed as a mobile phase when the initial concentration of U(VI) was 160 µM. Further experiments with different initial U(VI) concentrations (25 - 900 M) in MTM with PIPES or bicarbonate buffers indicated that aggregation of uraninite depended on the initial concentrations of U(VI) and type of buffer. It is known that under some conditions SRB-mediated UO 2 nanocrystals can be reoxidized (and thus remobilized) by Fe(III)-(hydr)oxides, common constituents of soils and sediments. To elucidate the mechanism of UO 2 reoxidation by Fe(III) (hydr)oxides, we studied the impact of Fe and U chelating compounds (citrate, NTA, and EDTA) on reoxidation rates. Experiments were conducted in anaerobic batch systems in PIPES buffer. Results showed EDTA significantly accelerated UO 2 reoxidation with an initial rate of 9.5 M day-1 for ferrihydrite. In all cases, bicarbonate increased the rate and extent of UO 2 reoxidation with ferrihydrite. The highest rate of UO 2 reoxidation occurred when the chelator promoted UO 2 and Fe(III) (hydr)oxide dissolution as demonstrated with EDTA. When UO 2 dissolution did not occur, UO 2 reoxidation likely proceeded through an aqueous Fe(III) intermediate as observed for both NTA and citrate. To complement to these laboratory studies, we collected U-bearing samples from a surface seep at the Rifle field site and have measured elevated U concentrations in oxic iron-rich sediments. To translate experimental results into numerical analysis of U fate and transport, a reaction network was developed based on Sani et al. (2004) to simulate U(VI) bioreduction with concomitant UO 2 reoxidation in the presence of hematite or ferrihydrite. The reduction phase considers SRB reduction (using lactate) with the reductive dissolution of Fe(III) solids, which is set to be microbially mediated as well as abiotically driven by sulfide. Model results show the oxidation of HS– by Fe(III) directly competes with UO 2 reoxidation as Fe(III) oxidizes HS– preferentially over UO 2 . The majority of Fe reduction is predicted to be abiotic, with ferrihydrite becoming fully consumed by reaction with sulfide. Predicted total dissolved carbonate concentrations from the degradation of lactate are elevated (log(pCO 2 ) ~ –1) and, in the hematite system, yield close to two orders-of-magnitude higher U(VI) concentrations than under initial carbonate concentrations of 3 mM. Modeling of U(VI) bioreduction with concomitant reoxidation of UO 2 in the presence of ferrihydrite was also extended to a two-dimensional field-scale groundwater flow and biogeochemically reactive transport model for the South Oyster site in eastern Virginia. This model was developed to simulate the field-scale immobilization and subsequent reoxidation of U by a biologically mediated reaction network.

54 ENVIRONMENTAL SCIENCES↗

Recovery of Mo in LEU-Modified Cintichem Process at Elevated Mo Concentrations

Argonne National Laboratory with support from DOE’s National Nuclear Security Administration Office of Material Management & Minimization (M 3 ) is helping SHINE Medical Technologies in developing domestic production of Mo-99. SHINE is planning to produce Mo-99 by fission of low enriched uranium-235 (LEU) in a subcritical aqueous solution using accelerator-based neutron generation. SHINE’s subcritical system can contain ~250L of LEU solution that is processed through a recovery titania-based column to recover Mo, while the remaining LEU solution can be available for another irradiation. The Mo-containing solution is then fed into another titania-based concentration column to further concentrate the solution to allow for the final purification step using the LEU modified Cintichem (LMC) process. The LMC process is a relatively small-scale process that was designed to work with 50mL volumes. By concentrating the Mo solution that feeds into the LMC process from ~250L to ~50mL, the actual chemical concentration of Mo becomes important. It is estimated that up to ~15mM Mo concentration could be present in the LMC feed. Since the LMC process was originally proposed for purification of Mo after dissolution of irradiated U solid targets, the chemical concentration of Mo was not a concern, due to presence of only trace amounts of Mo.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Waste Treatment and Immobilization Plant, a Leader in the International Glass Community - 16003

The U.S. Department of Energy (DOE), Office of River Protection (ORP) is constructing the Tank Waste Treatment and Immobilization Plant (WTP) [1] to treat radioactive waste currently stored in underground tanks at the Hanford Site in Washington State. The WTP that is being designed to separate the tank waste into high-level waste (HLW) and low-activity waste (LAW) fractions with the majority of the mass (approximately 90 percent) directed to LAW and most of the activity (greater than 95 percent) directed to HLW. The pretreatment process, envisioned in the baseline, involves the dissolution of aluminum bearing solids to allow the aluminum salts to be processed through the cesium ion exchange and report to the LAW Facility. There is an oxidative leaching process to affect a similar outcome for chromium-bearing wastes. These two unit operations were advanced to accommodate shortcomings in glass formulation for HLW inventories. A significant consideration to the most recent revision of the glass models is the extensive collaboration developed, funded, managed, and coordinated from the ORP. The current effort includes researchers at the Pacific Northwest National Laboratory, Idaho National Laboratory, Savannah River National Laboratory, Brookhaven National Laboratory, Catholic University of America, Washington State University, Rutgers University, Institute of Chemical Technology Prague, University of Ottawa, Tokyo Institute of Technology, The University of Adelaide, and University of Sheffield. Independent technical evaluation having been solicited from faculty of Alfred University and Vanderbilt University. These advances in glass chemistry generate a need to revisit the feed vectors, flowsheet, and the unit operations driven by minimal waste loading requirements set forth in the contract for the design and construction of the plant. The current status and plans for the immediate future of glass chemistry are the subject of the primary concern to successfully completing our clean-up mission at Hanford. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

TANK 12 SLUDGE CHARACTERIZATION AND ALUMINUM DISSOLUTION DEMONSTRATION

A 3-L sludge slurry sample from Tank 12 was characterized and then processed through an aluminum dissolution demonstration. The dominant constituent of the sludge was found to be aluminum in the form of boehmite. The iron content was minor, about one-tenth that of the aluminum. The salt content of the supernatant was relatively high, with a sodium concentration of {approx}7 M. Due to these characteristics, the yield stress and plastic viscosity of the unprocessed slurry were relatively high (19 Pa and 27 cP), and the settling rate of the sludge was relatively low ({approx}20% settling over a two and a half week period). Prior to performing aluminum dissolution, plutonium and gadolinium were added to the slurry to simulate receipt of plutonium waste from H-Canyon. Aluminum dissolution was performed over a 26 day period at a temperature of 65 C. Approximately 60% of the insoluble aluminum dissolved during the demonstration, with the rate of dissolution slowing significantly by the end of the demonstration period. In contrast, approximately 20% of the plutonium and less than 1% of the gadolinium partitioned to the liquid phase. However, about a third of the liquid phase plutonium became solubilized prior to the dissolution period, when the H-Canyon plutonium/gadolinium simulant was added to the Tank 12 slurry. Quantification of iron dissolution was less clear, but appeared to be on the order of 1% based on the majority of data (a minor portion of the data suggested iron dissolution could be as high as 10%). The yield stress of the post-dissolution slurry (2.5 Pa) was an order of magnitude lower than the initial slurry, due most likely to the reduced insoluble solids content caused by aluminum dissolution. In contrast, the plastic viscosity remained unchanged (27 cP). The settling rate of the post-dissolution slurry was higher than the initial slurry, but still relatively low compared to settling of typical high iron content/low salt content sludges. Approximately 40% of the post-dissolution sludge settled over a three week period. The corresponding volume of supernatant that was decanted from the waste was approximately 35% of the total waste volume. The decanted supernatant contained approximately one-third of the dissolved aluminum and exhibited a mild greenish-grey hue.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Tank 12 Sludge Characterization and Aluminum Dissolution Demonstration

A 3-L sludge slurry sample from Tank 12 was characterized and then processed through an aluminum dissolution demonstration. The dominant constituent of the sludge was found to be aluminum in the form of boehmite. The iron content was minor, about one-tenth that of the aluminum. The salt content of the supernatant was relatively high, with a sodium concentration of {approx}7 M. Due to these characteristics, the yield stress and plastic viscosity of the unprocessed slurry were relatively high (19 Pa and 27 cP), and the settling rate of the sludge was relatively low ({approx}20% settling over a two and a half week period). Prior to performing aluminum dissolution, plutonium and gadolinium were added to the slurry to simulate receipt of plutonium waste from H-Canyon. Aluminum dissolution was performed over a 26 day period at a temperature of 65 C. Approximately 60% of the insoluble aluminum dissolved during the demonstration, with the rate of dissolution slowing significantly by the end of the demonstration period. In contrast, approximately 20% of the plutonium and less than 1% of the gadolinium partitioned to the liquid phase. However, about a third of the liquid phase plutonium became solubilized prior to the dissolution period, when the H-Canyon plutonium/gadolinium simulant was added to the Tank 12 slurry. Quantification of iron dissolution was less clear, but appeared to be on the order of 1% based on the majority of data (a minor portion of the data suggested iron dissolution could be as high as 10%). The yield stress of the post-dissolution slurry (2.5 Pa) was an order of magnitude lower than the initial slurry, due most likely to the reduced insoluble solids content caused by aluminum dissolution. In contrast, the plastic viscosity remained unchanged (27 cP). The settling rate of the post-dissolution slurry was higher than the initial slurry, but still relatively low compared to settling of typical high iron content/low salt content sludges. Approximately 40% of the post-dissolution sludge settled over a three week period. The corresponding volume of supernatant that was decanted from the waste was approximately 35% of the total waste volume. The decanted supernatant contained approximately one-third of the dissolved aluminum and exhibited a mild greenish-grey hue.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

THE SUITABILITY OF SODIUM PEROXIDE FUSION FOR PRODUCTION-SCALE PLUTONIUM PROCESSING OPERATIONS

Sodium peroxide (Na{sub 2}O{sub 2}) fusion is a method that offers significant benefits to the processing of high-fired plutonium oxide (PuO{sub 2}) materials. Those benefits include reduction in dissolution cycle time, decrease in residual solids, and reduction of the potential for generation of a flammable gas mixture during dissolution. Implementation of Na{sub 2}O{sub 2} fusion may also increase the PuO{sub 2} throughput in the HB-Line dissolving lines. To fuse a material, Na{sub 2}O{sub 2} is mixed with the feed material in a crucible and heated to 600-700 C. For low-fired and high-fired PuO{sub 2}, Na{sub 2}O{sub 2} reacts with PuO{sub 2} to form a compound that readily dissolves in ambient-temperature nitric acid without the use of potassium fluoride. The Savannah River National Laboratory (SRNL) demonstrated the feasibility of Na{sub 2}O{sub 2} fusion and subsequent dissolution for the processing of high-fired PuO{sub 2} materials in HB-Line. Testing evaluated critical dissolution characteristics and defined preliminary process parameters. Based on experimental measurements, a dissolution cycle can be complete in less than one hour, compared to the current processing time of 6-10 hours for solution heating and dissolution. Final Pu concentrations of 30-35 g/L were produced without the formation of precipitates in the final solution.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural pattern formation during liquid metal dealloying: Phase-field simulations and theoretical analyses

In recent years, liquid metal dealloying has emerged as a promising material processing method to generate micro- and nanoscale bicontinuous or porous structures. Most previous studies focused on the experimental characterization of the dealloying process and on the properties of the dealloyed materials, leaving the theoretical study incomplete to fully understand the fundamental mechanisms of the liquid metal dealloying process. In this paper, we use theoretical models and phase-field simulations to clarify the kinetics and pattern formation during liquid metal dealloying. Our investigation starts from a theoretical analysis of the 1D dissolution of a binary precursor alloy, which reveals that the 1D dissolution process involves two regimes. In the first regime, due to the low solubility of one of the elements in the melt, it accumulates at the solid-liquid interface, which reduces the dissolution kinetics. In the second regime, the interface kinetics reaches a stationary regime where both elements of the precursor alloy dissolve into the melt. Previous works revealed that in the early dealloying stage, the dealloying front is destabilized by an interfacial spinodal decomposition, which triggers the formation of interconnected ligaments. Here we extend this line of work by proposing a linear stability analysis able to predict the initial length scale of the ligaments formed in the initial stage of the dealloying. Combining this analysis with the 1D dissolution model proposed here enables us to better understand the initial conditions (composition of the precursor alloy and the melt) leading to a planar dissolution without interface destabilization. Finally, we report a strong influence of solid-state diffusion on dealloying. Although the solid-state diffusivity is four to five orders of magnitude smaller than in the liquid phase, it is found to affect both dissolution kinetics and ligament morphologies.

36 MATERIALS SCIENCE↗

Continuous optical in-situ pH monitoring during early hydration of cementitious materials

A luminescent sensor technique for pH analyses has been tested in cementitious media. The optical sensors monitor in-situ pH every 5 s during early hydration reactions over a period of 100 h from initial fluid up to consolidated stage. The pH development was analysed in calcium aluminate, calcium sulfoaluminate and OPC/slag cements up to a pH level of 13.3 and directly correlated with the heat of hydration. Thus tracing the dissolution and formation processes of solid phases via pH sensor monitoring is possible. This measurement technique enables the recording of continuous and highly reproducible pH data sets from slurries, pastes, and hardening materials leading to new vistas for individual (trans)formation pathways of solids, hydration and consolidation reactions in high alkaline cementitious systems.

36 MATERIALS SCIENCE↗

DISSOLUTION OF NEPTUNIUM OXIDE RESIDUES

This report describes the development of a dissolution flowsheet for neptunium (Np) oxide (NpO{sub 2}) residues (i.e., various NpO{sub 2} sources, HB-Line glovebox sweepings, and Savannah River National Laboratory (SRNL) thermogravimetric analysis samples). Samples of each type of materials proposed for processing were dissolved in a closed laboratory apparatus and the rate and total quantity of off-gas were measured. Samples of the off-gas were also analyzed. The quantity and type of solids remaining (when visible) were determined after post-dissolution filtration of the solution. Recommended conditions for dissolution of the NpO{sub 2} residues are: Solution Matrix and Loading: {approx}50 g Np/L (750 g Np in 15 L of dissolver solution), using 8 M nitric acid (HNO{sub 3}), 0.025 M potassium fluoride (KF) at greater than 100 C for at least 3 hours. Off-gas: Analysis of the off-gas indicated nitric oxide (NO), nitrogen dioxide (NO{sub 2}) and nitrous oxide (N{sub 2}O) as the only identified components. No hydrogen (H{sub 2}) was detected. The molar ratio of off-gas produced per mole of Np dissolved ranged from 0.25 to 0.4 moles of gas per mole of Np dissolved. A peak off-gas rate of {approx}0.1 scfm/kg bulk oxide was observed. Residual Solids: Pure NpO{sub 2} dissolved with little or no residue with the proposed flowsheet but the NpCo and both sweepings samples left visible solid residue after dissolution. For the NpCo and Part II Sweepings samples the residue amounted to {approx}1% of the initial material, but for the Part I Sweepings sample, the residue amounted to {approx}8 % of the initial material. These residues contained primarily aluminum (Al) and silicon (Si) compounds that did not completely dissolve under the flowsheet conditions. The residues from both sweepings samples contained minor amounts of plutonium (Pu) particles. Overall, the undissolved Np and Pu particles in the residues were a very small fraction of the total solids.

08 HYDROGEN↗

CO 2 utilization in built environment via the P CO 2 swing carbonation of alkaline solid wastes with different mineralogy

Carbon mineralization to solid carbonates is one of the reaction pathways that can not only utilize captured CO 2 but also potentially store it in the long term. In this study, the dissolution and carbonation behaviors of alkaline solid wastes (i.e., waste concrete) was investigated. Concrete is one of the main contributors to a large carbon emission in the built environment. Thus, the upcycling of waste concrete via CO 2 utilization has multifaceted environmental benefits including CO 2 emission reduction, waste management and reduced mining. Unlike natural silicate minerals such as olivine and serpentine, alkaline solid wastes including waste concrete are highly reactive, and thus, their dissolution and carbonation behaviors vary significantly. Here, both conventional acid (e.g., hydrochloric acid) and less studied carbonic acid (i.e., CO 2 saturated water) solvent systems were explored to extract Ca from concrete. Non-stoichiometric dissolution behaviors between Ca and Si were confirmed under far-from-equilibrium conditions (0.1 wt% slurry density), and the re-precipitation of the extracted Si was observed at near-equilibrium conditions (5 wt% slurry density), when the Ca extraction was performed at a controlled pH of 3. These experiments, with a wide range of slurry densities, provided valuable insight into Si re-precipitation phenomena and its effect on the mass transfer limitation during concrete dissolution. Next, the use of the partial pressure of CO 2 for the pH swing carbon mineralization process was investigated for concrete, and the results were compared to those of Mg-bearing silicate minerals. In the P CO 2 swing process, the extraction of Ca was significantly limited by the precipitation of the carbonate phase (i.e., calcite), since CO 2 bubbling could not provide a low enough pH condition for concrete–water–CO 2 systems. Furthermore, this study showed that the two-step carbon mineralization via P CO 2 swing, that has been developed for Mg-bearing silicate minerals, may not be viable for highly reactive Ca-bearing silicate materials (e.g., concrete). The precipitated calcium carbonate (PCC) derived from waste concrete via a pH swing process showed very promising results with a high CO 2 utilization potential as an upcycled construction material.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

ANALYSIS OF THE LEACHING EFFICIENCY OF INHIBITED WATER AND TANK SIMULANT IN REMOVING RESIDUES ON THERMOWELL PIPES

A key component for the accelerated implementation and operation of the Salt Waste Processing Facility (SWPF) is the recovery of Tank 48H. Tank 48H is a type IIIA tank with a maximum capacity of 1.3 million gallons. Video inspection of the tank showed that a film of solid material adhered to the tank internal walls and structures between 69 inch and 150 inch levels. From the video inspection, the solid film thickness was estimated to be 1mm, which corresponds to {approx}33 kg of TPB salts (as 20 wt% insoluble solids) (1). This film material is expected to be easily removed by single-rinse, slurry pump operation during Tank 48H TPB disposition via aggregation processing. A similar success was achieved for Tank 49H TPB dispositioning, with slurry pumps operating almost continuously for approximately 6 months, after which time the tank was inspected and the film was found to be removed. The major components of the Tank 49H film were soluble solids - Na{sub 3}H(CO{sub 3}){sub 2} (Hydrated Sodium Carbonate, aka: Trona), Al(OH){sub 3} (Aluminum Hydroxide, aka: Gibbsite), NaTPB (Sodium Tetraphenylborate), NaNO{sub 3} (Sodium Nitrate) and NaNO{sub 2} (Sodium Nitrite) (2). Although the Tank 48H film is expected to be primarily soluble solids, it may not behave the same as the Tank 49H film. There is a risk that material on the internal surfaces of Tank 48H could not be easily removed. As a risk mitigation activity, the chemical composition and leachability of the Tank 48H film are being evaluated prior to initiating tank aggregation. This task investigated the dissolution characteristics of Tank 48H solid film deposits in inhibited water and DWPF recycle. To this end, SRNL received four separate 23-inch long thermowell-conductivity pipe samples which were removed from the tank 48H D2 risers in order to determine: (1) the thickness of the solid film deposit, (2) the chemical composition of the film deposits, and (3) the leaching behavior of the solid film deposit in inhibited water (IW) and in DWPF recycle simulant (3).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Polymer Nanogels as Reservoirs To Inhibit Hydrophobic Drug Crystallization

Herein the effects of cross-link density and composition on the loading and in vitro dissolution of the drug phenytoin as amorphous solid dispersions in emulsion polymerized poly(N-isopropylacrylamide) (PNIPAm) and poly(N-isopropylacrylamide-co-N,N-dimethylacrylamide) nanogels were investigated near the lower critical solution temperature (LCST). Nanogel size and particle density in phosphate buffered saline were quantified by dynamic light scattering (DLS) and viscometry experiments, while drug–nanogel interactions were revealed by cross peaks in aqueous-state nuclear Overhauser effect spectroscopy measurements. Spray-dried dispersions (SDDs) of drug-loaded PNIPAm nanogel particles (R ≈ 43 nm) were directly visualized by cryogenic transmission electron microscopy and further quantified by small-angle X-ray scattering during in vitro dissolution. SDD dissolution profiles were highly dependent on the nanogel cross-link density and directly correlated with the state of dispersion of the drug-loaded nanogel particles. A balance between net particle hydrophobicity and hydrophilicity along with the distance in temperature from the LCST are shown to dictate the in vitro dissolution of the amorphous solid dispersions. Solubility enhancement mechanisms disclosed in this study provide essential guidance for the design of effective nanogels for oral drug delivery applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Graphite Steel and Chromium-Nickel Steel Corrosion: Solution Flow Through Corrosion Experiments

The corrosion of steel, when exposed to various compositions of brines is a complex, heterogeneous process involving dissolution and precipitation of multiple solids. The rate at which elements will be released from the corrosion process under these conditions will depend, in part, on effects associated with secondary alteration phases (passivating film) that may potentially form under these conditions. Understanding these processes has required the development of sophisticated methods to sample and quantitatively characterize the composition of the steel as it corrodes and releases elements. The determination of the concentrations of both brine and steel corrosion components in solutions sampled from these tests is required to fully understand the process that may eventually lead to dissolution of corrosion products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Study of autunite dissolution in the presence of Shewanella oneidensis MR1 and different bicarbonate concentrations - 15736

Remediation of uranium at Hanford Site 300 area via tripolyphosphate injections could sequester uranium (VI) in an insoluble form, creating different types of uranium phosphate minerals like autunite. The factors that influence the dissolution of such minerals come into question. Bacteria can play a significant role in the dissolution of minerals and the formation of secondary minerals. Formed autunite, as a phosphorus-containing mineral, can attract bacteria to liberate phosphorus, meeting their nutrient requirements and causing uranium release back into the environment. Previous studies have been conducted under aerobic conditions. This research was extended to investigate the stability of the autunite mineral under anaerobic conditions pertaining to the Hanford Site, and to study the effect of facultative anaerobic bacteria on the uranium (VI) release from autunite. Objectives: - Evaluate bacterial interactions with uranium (VI) by focusing on facultative anaerobic bacteria, Shewanella Oneidensis MR1. - Study the effect of bacteria on the dissolution of the uranyl phosphate solid phases created as a result of sodium tripolyphosphate injections into the subsurface at the Hanford 300 Area. - Evaluate the role of anaerobic bacteria as one of the factors affecting the outcome of environmental remediation. Experimental Approach: - 16 crimp-sealed bottles were prepared with 50 ml of media solution and 90 mg (4.4 mM of uranium VI) Ca-autunite mineral obtained from Hanford site. Bottles were inoculated with Shewanella Oneidensis MR1 strains when autunite was equilibrated with the media solutions. Bacteria was obtained from Pacific Northwestern National Laboratory (PNNL). - Solution media preparation: 20 mM NaHepes buffer: pH=7, 10 mM Lactate plus bicarbonate in four concentrations (0, 3, 5 and 10 of KHCO{sub 3}) and a bacteria-free control. Samples were taken from the supernatant solutions of the experimental and control bottles. Wet and dry digestion was performed until a white solid residue was acquired. Dilution was made on solid samples for KPA analysis to determine concentration of U (VI) as function of time. The results suggests that in the absence of HCO{sub 3}{sup -} there was a decrease in the of uranium (VI) concentration due to metal reducing bacteria Shewanella Oneidensis MR1, but for higher concentrations of HCO{sub 3}{sup -}, there is no significant difference in uranium (VI) reduction before and after inoculation with bacteria. - Although bottles were sealed, there is an hypothesis that it was oxygen restricted but not strictly performed under anaerobic conditions. For that matter there is a reason to repeat the experiment using the glove box to understand the uranium (VI) reduction mechanism and behavior of bacteria with oxic/anoxic interfaces. Conclusions: - Higher bicarbonate concentrations might interfere with uranium (VI) reduction by anaerobic bacteria. - It is necessary to reduce time of sampling before the inoculation and prolong sampling time after inoculation. - It might be necessary to increase concentration of lactate. Future Work: - Conduct experiment in strictly anaerobic conditions by using the glove box and evaluate if further reduction of uranium (VI) is obtained in the presence of carbonates (HCO{sub 3}{sup -}). - Finalize analysis of calcium and phosphorous via ICP instrument.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Disordered interfaces of alkaline aluminate salt hydrates provide glimpses of Al 3+ coordination changes

Hypothesis: The precipitation and dissolution of aluminum-bearing mineral phases in aqueous systems often proceed via changes in both aluminum coordination number and connectivity, complicating molecular-scale interpretation of the transformation mechanism. Here, the thermally induced transformation of crystalline sodium aluminum salt hydrate, a phase comprised of monomeric octahedrally coordinated aluminate which is of relevance to industrial aluminum processing, has been studied. Because intermediate aluminum coordination states during melting have not previously been detected, it is hypothesized that the transition to lower coordinated aluminum ions occurs within a highly disordered quasi-two-dimensional phase at the solid-solution interface. Experiments and simulations: In this work, in situ X-ray diffraction (XRD), Raman and 27 Al nuclear magnetic resonance (NMR) spectroscopy were used to monitor the melting transition of nonasodium aluminate hydrate (NSA, Na 9 [Al(OH) 6 ] 2 ·3(OH)·6H 2 O). A mechanistic interpretation was developed based on complementary classical molecular dynamics (CMD) simulations including enhanced sampling. A reactive forcefield was developed to bridge speciation in the solution and in the solid phase. Findings: In contrast to classical dissolution, aluminum coordination change proceeds through a dynamically stabilized ensemble of intermediate states in a disordered layer at the solid-solution interface. In both melting and dissolution of NSA, octahedral, monomeric aluminum transition through an intermediate of pentahedral coordination. The intermediate dehydroxylates to form tetrahedral aluminate (Al(OH)$_4^–$) in the liquid phase. This coordination change is concomitant with a breaking of the ionic aluminate-sodium ion linkages. The solution phase Al(OH)$_4^–$ ions subsequently polymerize into polynuclear aluminate ions. However, there are some differences between bulk melting and interfacial dissolution, with the onset of the surface-controlled process occurring at a lower temperature (~30 °C) and the coordination change taking place more gradually as a function of temperature. This work to determine the local structure and dynamics of aluminum in the disordered layer provides a new basis to understand mechanisms controlling aluminum phase transformations in highly alkaline solutions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Physics-Based Continuum Modeling for an Aqueous Rechargeable Zn/MnO 2 Battery

This study introduces a framework for modeling the aqueous Zn/MnO 2 rechargeable battery. A reaction system and a physics-based continuum model are proposed based on two reaction types, one involving insertion and the second related to dissolution and deposition of a solid reaction product. The model, fitted to empirical data, predicts voltage behavior and capacity limitations during cycling, identifying electrolytic zinc depletion as a limiting mechanism, depending on the original cell construction. The research suggests the need for further material characterization and reaction analysis, which will advance our understanding and facilitate the development of grid-scale energy storage solutions.

Electrochemistry↗