SEARCH · Engineering Papers
Results for “Sizing”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Electronic impact of Ni2P nanoparticle size on hydrogenation rates
Nickle phosphide, Ni2P, nanoparticles supported on SiO2 show a marked volcano shaped size dependence. Kinetic analysis and physicochemical characterization shows the electron density of Ni to increase with increasing Ni2P size, enhancing in turn the H2 adsorption strength. For particles below 15 nm, H adsorbs weakly causing a low surface coverage of H, gradually increasing with particle size. For large particles, hydrogen binds too strongly causing a high coverage but low catalytic activity. The remarkable size dependence of the electronic properties show that Ni2P particle size can be used to fine-tune its activity for hydrogenation.
The effect of gravel size fraction on the distribution coefficients of selected radionuclides radionuclides
This manuscript addresses the consequences of the common practice of assuming that the gravel fraction of sediments does not participate in sorption reactions and thus sorption quantified by the distribution coefficient (Kd) construct can be estimated from laboratory tests on < 2mm fraction of sediments. As shown within the use of this common assumption can lead to inaccurate estimates of the mobility and sorption capacity of key radionuclides (Tc, U, and Np) at the Hanford Site where gravel dominates the lower Hanford formation and upper Ringold Formation. Batch sorption and column experiments showed that the distribution coefficient measured using only < 2mm fraction were not in agreement with those obtained from the bulk sediments depending on the radionuclide. The least reactive radionuclide, Tc showed the lowest effects from the presence of gravel. However, differences between measured Kds using < 2mm fractions of the sediment and the Kds measured on the bulk sediment were significant for strongly reactive radionuclides such as Np, especially on the sediment with gravel fractions that contained highly reactive sites. Highly reactive sites in the gravel fraction were attributed to the presence of Fe oxides coatings and/or reactive fracture faces on the gravel surfaces. Gravel correction factors that use the sum of the Kd,<2 mm and Kd,>2 mm values to estimate the Kd for the bulk sediment were found to best describe Kds for radionuclides on the bulk sediment. However, more detailed characterization of gravel surfaces should be also conducted to identify those gravels with higher reactive sorbents, if present. Gravel correction factors should be considered to predict precisely the sorption capacity of bulk sediments that contain more than 10% gravel and to estimate the mobility of contaminants in subsurface environments.
Evaluating Entrainment–Mixing Characteristics through Direct Comparisons of Drop Size Distributions Using In Situ Observations from ACE-ENA
Abstract Constraining the impacts of entrainment and associated mixing (i.e., entrainment–mixing) on cloud properties continues to be difficult, partly due to observational uncertainties as well as a lacking consensus of which methodologies for diagnosing entrainment–mixing are most appropriate. This study introduces a novel method to evaluate the presence and degree of inhomogeneous and homogeneous mixing using ∼100 h of in situ observations from a research aircraft over the northeastern Atlantic. Specifically, drop size distributions are compared between regions containing negligible and significant entrainment for select flight legs, making a direct characterization of the degree of homogeneous and inhomogeneous mixing possible. A measure of drop concentration variance is used as a proxy variable to diagnose entrainment–mixing. Results correspond well with entrainment–mixing metrics, showing lower Damköhler numbers where drop size distributions shift toward smaller drop sizes (i.e., inhomogeneous mixing) and greater transition length scales where drop size distributions do not (i.e., homogeneous mixing). Inhomogeneous mixing occurs in most samples from Aerosol and Cloud Experiment in the Eastern North Atlantic (ACE-ENA) (regardless of homogeneous mixing frequencies increasing with increasing spatial resolution from ∼100 to ∼10 m) and is associated with decreased drop size relative dispersion and both greater aerosol and drop concentrations compared with homogeneous mixing. Precipitating clouds have a greater frequency of homogeneous mixing compared with nonprecipitating clouds. The proposed methodology is similarly applied to in situ observations of southeast Pacific stratocumulus, shallow convective clouds over central Oklahoma and low-level clouds over the Southern Ocean. All four locations are primarily dominated by inhomogeneous mixing with minimal variability among each region.
Spatial variation in soil microbial processes as a result of woody encroachment depends on shrub size in tallgrass prairie
Aims: As woody plants encroach into grassland ecosystems, we expect that altered plant-soil interactions will lead to changes in the microbial processes that affect carbon storage and nutrient cycling. Specifically, this research aimed to address how (1) soil chemistry, (2) microbial nutrient demand, and (3) the rate and source of potential soil C mineralization vary spatially under individual woody shrubs of varying size within a mesic grassland. Methods: Here, we collected soil samples from the center, the midpoint between the center and edge, the edge, and the shrub-grass ecotone of multiple Cornus drummondii shrubs across a shrub-size gradient in infrequently burned tallgrass prairie. Results: We found total soil carbon and total soil nitrogen increased with shrub size in every location but the edge. Microbial demand for nitrogen also increased as shrubs increased in size. Across all shrub sizes and sampling locations, potential soil carbon mineralization rates were higher when microbes broke down proportionally more shrub-derived (C 3 ) organic matter than grass-derived (C 4 ) organic matter. Conclusions: Our results suggest that the spatio-temporal context of woody encroachment is critical for understanding its impact on belowground microbial processes. In this ecosystem, a longer period of occupancy by woody plants increases potentially mineralizable carbon.
Localized melt-scan strategy for site specific control of grain size and primary dendrite arm spacing in electron beam additive manufacturing
Not Available
Effects of particle size and AQDS on the flow of electron equivalents between magnetite and aqueous Fe2+
Magnetite can occur naturally in nano- to micro-size regimes and widely coexists with aqueous Fe2+ (Fe2+ (aq)) in natural environments. However, the effects of magnetite particle size on its interaction with Fe2+ (aq) in anoxic subsurface environments, particularly with redox-active organics, remain unclear. In this study, the interactions of Fe2+ (aq) with magnetite particles of 12 nm versus 109 nm (Mag-12 vs. Mag-109), with/without anthraquinone- 2,6-disulfonate (AQDS), were studied based on equilibrium Fe2+ (aq) concentrations, kinetics of AQDS reduction, and structural versus surface-localized Fe(II)/Fe(III) ratios (xstru and xsurf) of magnetite. In the absence of AQDS, Mag-12 tends to release Fe2+ (aq) at pH 7 but sorb Fe2+ (aq) at pH 8, while Fe2+ (aq) uptake by Mag-109 is observed at both pH 7 and 8. The amounts of Fe2+ (aq) adsorbed per unit area of Mag-109 is higher than that of Mag-12, due to the higher electron-accepting capacity of Mag-109 that facilitates interfacial electron transfer (IET) from surfaceassociated Fe(II) to structural Fe(III). The increases of xstru and xsurf in Mag-109 after reaction with Fe2+ (aq) at pH 7 and 8 suggest Fe2+ (aq) incorporation or electron injection into the structure of Mag-109. The presence of AQDS promotes Fe2+ (aq) uptake by both Mag-12 and Mag-109. However, AQDS reduction by Fe2+-amended Mag-12 results in the decrease of xstru and inhibits Fe2+ (aq) incorporation or electron injection into the structure. On the contrary, the increase of xstru observed in Fe2+-amended Mag-109 after reaction with AQDS suggests that Fe2+ (aq) incorporation or electron injection into the surface structure and then consequently into the interiors is more favorable for magnetite with larger particle sizes. The different flow directions of electron equivalents across the solid-solution interfaces can be attributed to the relatively higher electron-accepting capacity, i.e. redox potential, of Mag-109 than Mag-12; larger particle sizes facilitate IET from surface-associated Fe(II) to structural Fe(III) and promotes further Fe2+ (aq) uptake, culminating in the pronounced changes of redox potentials in magnetitebearing solutions. The results demonstrate that particle size and redox-active organics are important factors to affect reductive activity of Fe2+-magnetite system in redox-oscillating environments.
Micrometer-sized Magnetite Synthesis using Fe(OH)2(s) as a Precursor for Technetium Sequestration from Liquid Nuclear Waste Streams
Systematic batch experiments under variable adjusted physicochemical conditions were conducted to explore optimization of micrometer-sized magnetite synthesis for Tc sequestration from radionuclide waste streams using Fe(OH)2(s) as the precursor. Extensive solid characterization using x-ray diffraction and spectroscopic methods was performed to assess changes in particle morphology and size distribution, as well as Tc speciation and incorporation, in the produced mineral phases. The results show that the solution pH, temperature, and oxidation kinetics play key roles in the final mineral products. Micrometer-sized magnetite crystals (0.62-0.96 µm on average) with well-defined dodecahedral or octahedral structures were synthesized under near neutral (~pH 8) or alkaline (~pH13) conditions at 75 °C, respectively; whereas goethite dominated the end products at room temperature. An increase in pH at 75 °C improved Tc removal from 27% (near neutral pH) to 42% (alkaline pH), but the removal process remained inhibited by redox competitive Cr(VI) present in the waste streams. By adding additional Fe(II) to the system, Tc sequestration was dramatically improved to up to 87% without observable changes in the solid product. The sequestrated Tc existed as TcO2·2H2O and/or Tc(IV) incorporated into magnetite, where extended X-ray absorption fine structure (EXAFS) spectroscopy showed that more Tc was incorporated into magnetite at elevated temperatures and pH conditions, with complete Tc(IV) incorporation into magnetite occurring under 75 °C-pH 13 conditions. Our results indicate that optimal micrometer-sized magnetite can be produced for Tc sequestration by reacting Fe(OH)2(s) with a waste stream simulant under elevated pH (~13) and temperature (75 °C) conditions. The incorporation of reduced Tc(IV) into stable micrometer-sized magnetite provides a viable supplemental immobilizing technology that may be used to improve nuclear waste treatment and disposal needs.
Resolving Detonation NanoDiamond Size Evolution and Morphology at Sub-Microsecond Time-Scales During High-Explosive Detonations
Characterization of the initial morphology of detonation nanodiamond (DND) has been the focus of many research studies that aim to develop fundamental understanding of carbon condensation under extreme conditions. Identifying the pathways of DND formation has the potential for significant impact in many of the controlled synthesis of nanoscale carbon with tailored functionality; currently, a wide range of possible (and conflicting) mechanisms of nucleation and growth have been proposed and further research is essential. Building a comprehensive understanding of DND formation is challenging because it requires in situ characterization on the sub-µs time-scale during a high explosive detonation. In this study, time resolved small angle X-ray scattering (TR-SAXS) is used to reveal the early-stage DND morphology from < 0.1 μs to 6 μs after the detonation front passes through the X-ray beam path. We address the ambiguity of models previously reported for analysis of small angle scattering from DND by comparing (i) in situ, TR-SAXS recorded during early-stage particulate formation and (ii) ex situ SAXS and transmission electron microscopy measurements (TEM) of products recovered from detonation of the same high-explosive within a carefully designed ice chamber. The SAXS from both late-time ( > 1 μs) in situ and recovered DND exhibit consistent features in the I(q) curve. Such close similarity allows a high fidelity SAXS model derived from the ex situ SAXS and TEM measurements to be applied to the in situ data, which yields new insight into the early stage (< 1µs) morphology of DND. Our analysis indicates a size-distribution of DND particles is observed within 0.1 μs post-detonation and have a mean core diameter slightly below 4 nm and surface texture that consists of hemispherical protrusions that extend ~ 1 nm from the surface. Beyond ~ 0.3 μs, the size distribution increases slightly, while the surface texture persists for several microseconds after the detonation. Combined with thermochemical simulations, these results indicate that during detonation of Composition B, carbon is condensed into nanoscale diamond much faster than previously reported in other studies. Furthermore, the surface texture of the DND is shown to arise during condensation rather than via subsequent graphitization.
Size-dependent kinetics during non-equilibrium lithiation of nano-sized zinc ferrite
Spinel transition metal oxides (TMOs) have emerged as promising anode materials for lithium-ion batteries. It has been shown that reducing their particle size to nanoscale dimensions benefits overall electrochemical performance. Here, we use in situ transmission electron microscopy to probe the lithiation behavior of spinel ZnFe 2 O 4 as a function of particle size. We have found that ZnFe 2 O 4 undergoes an intercalation-to-conversion reaction sequence, with the initial intercalation process being size dependent. Larger ZnFe 2 O 4 particles (40 nm) follow a two-phase intercalation reaction. In contrast, a solid-solution transformation dominates the early stages of discharge when the particle size is about 6–9 nm. Using a thermodynamic analysis, we find that the size-dependent kinetics originate from the interfacial energy between the two phases. Furthermore, the conversion reaction in both large and small particles favors {111} planes and follows a core-shell reaction mode. Finally, these results elucidate the intrinsic mechanism that permits fast reaction kinetics in smaller nanoparticles.
Effect of quantum dot size and size distribution on the intersublevel transitions and absorption coefficients of III-V semiconductor quantum dot
The intersublevel absorption peak energy and absorption coefficient of non-uniform quantum dot (QD) ensembles are calculated analytically. The effect of size variations and size distribution of QDs on their energy states is analyzed. The dots are considered as a quantum box with finite potential at the barriers and the size distribution described by a Gaussian function. The influence of the aspect ratio (base to height ratio) of the QDs on the optical transitions is studied. Our model predicts the dot size (height and base) accurately to determine the absorption peaks and corresponding absorption coefficient. We also compute the absorption coefficient of the QD with different size distributions to verify the results calculated using this model with the reported experimental and other theoretical results.
Soot particle sizing during high-pressure Diesel spray combustion via time-resolved laser-induced incandescence
Single-pulse time-resolved laser-induced incandescence (TiRe-LII) signal transients from soot particulates were acquired during unsteady high pressure Diesel combustion in a constant volume cell for typical top dead center conditions during a Diesel engine cycle. Measurements were performed for initial gas pressures between 1 and 3 MPa, injection pressures between 50 and 130 MPa and laser probe timings between 5 and 16 ms after start of fuel injection. In separate experiments and for the same cell operating conditions gas temperatures were deduced from spectrally resolved soot pyrometry measurements. Implementing the LII model of Kock et al. [Combust. Flame 147 (20006) 79-92] ensemble mean soot particle diameters were evaluated from least-squares fitting of theoretical cooling curves to experimental TiRe-LII signal transients. Since in the experiments the environmental gas temperature and the width of an assumed particle size distribution were not known, the effects of the initial choice of these parameters on retrieved particle diameters were investigated. It is shown that evaluated mean particle diameters are only slightly biased by the choice of typical size distribution widths and gas temperatures. For a fixed combustion phase mean particle diameters are not much affected by gas pressure, however they become smaller at high fuel injection pressure. At a mean chamber pressure of 1.39 MPa evaluated mean particle diameters increased by a factor of two for probe delays between 5 and 16 ms after start of injection irrespective of the choices of first-guess fitting variables, indicating a certain robustness of data analysis procedure. (author)
Accuracy of Centerline of Flow Measurement for Sizing of the Zenith AAA Endovascular Graft and Predictive Factor for Risk of Inadequate Sizing
The purpose of this study was to evaluate the accuracy of centerline of flow (CLF) measurement for precise sizing of the Zenith AAA endovascular graft (Zenith) and to identify predictive factors of risk of inadequate endograft sizing. We analyzed 42 consecutive patients treated using the Zenith with pre- and postoperative multidetector CT between 2001 and 2007. Endograft sizing was retrospectively performed using CLF on a three-dimensional workstation. The following parameters were investigated: (a) change in distance from lowest renal artery to hypogastric artery between CLF on preoperative CT (CLFp) and CLF of graft path on postoperative CT (CLFg); (b) supposed success rate of adequate endograft length selection; and (c) predictive factors for significant alteration (>10 mm) between CLFp and CLFg. Median change in distance from lowest renal artery to hypogastric artery was 4 mm. CLFg was >10 mm shorter than CLFp in 10 of 84 limbs (12%). Multivariate analysis demonstrated tortuosity index (TI) of infrarenal abdominal aorta (p = 0.019), aneurysm diameter (p = 0.035), and ipsilateral side of the main body insertion (p = 0.042) as predictive factors of significant alteration between CLFp and CLFg. Adequate endograft length selection was achieved in 39 of 42 cases (93%). All three inadequate endograft length selections were associated with tortuous aorta (TI > 20 mm). In conclusion, distance calculations based on CLF measurement provided accurate length selection of the Zenith in the majority of cases. TI, aneurysm diameter, and ipsilateral side were predictive factors for significant alteration. The CLF and aortic measurements including the TI may allow for improved sizing for Zenith placements.
CdSe Magic-Size Clusters Deviate from Nanocrystal-Size Scalings for Ultrafast Intraband Relaxation and Auger Recombination
The cluster regime of colloidal semiconductor quantum dots (QDs) occupies an interesting space on the continuum from molecule to bulk material and allow the study of QD properties at extreme quantum confinement limits. For typical QDs, several size-dependent property trends are well established including intraband relaxation rates and universal scaling of Auger recombination with particle volume. Advances in synthesis now allow isolation of atomically precise semiconductor magic-size clusters (MCs), which offer experimental insight regarding how electronic structure changes with particle size in the ultrasmall limit. Here, we report intraband cooling and Auger recombination for several stable CdSe MCs as a function of particle size and observe deviation from QD response in the cluster regime. We additionally show optical signatures ascribed to transient disordering 2 that appear in the single exciton regime for MCs, which point to complexities regarding their implementation.
Male body size predicts reproductive success but not within-clutch paternity patterns in gopher tortoises ( Gopherus polyphemus )
In many vertebrates, body size is an important driver of variation in male reproductive success. Larger, more fit individuals are more likely to dominate mating opportunities, skewing siring success and resulting in lower effective population sizes and genetic diversity. The mating system of the gopher tortoise (Gopherus polyphemus) has been characterized as both female defense and scramble-competition polygyny. Mating systems are typically not fixed and can be influenced by factors such as population density, demographic structure, and environmental conditions;, however, most populations will have a predominant strategy that results from local conditions. We assessed how male body size influences patterns of paternity and reproductive success in a natural population of gopher tortoises in Florida, USA. Using microsatellites, we assigned parentage of 220 hatchlings from 31 nests collected during two reproductive seasons. Larger males were significantly more likely to sire offspring and sired more offspring than smaller males; however, the likelihood of a clutch being multiply-sired was unrelated to male body size. We also found evidence of mate fidelity across years. Although paternity patterns in this high-density population are more consistent with defense polygyny, female monopoly by males was incomplete, with both large and small males contributing to multiply-sired clutches. Additional behavioral data are needed to clarify the role of female mate selection in paternity outcomes. The context-dependence of mating systems underscores the need to compare parentage patterns across populations and to recognize the potential for more than one strategy to be employed within a single population.