Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Sintering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Relation between microstructural heterogeneous surface layer and nitrogen pressure during sintering in Si3N4-Ml2O3 ceramics

The effects of N2 pressure (0.1 to 50 MPa) during sintering on the thickness of the microstructurally heterogeneous layer (MHL) formed near the surface of the compact, transverse-rupture strength, were investigated for Si3N4-(10 to 20) mol % MgO-5.5 mol % Al2O3 ceramics. The sintering temperature and time were 1973 K and 3.6 ks, respectively. The N2 gas was introduced into the furnace at about 1273 K. When the compacts were sintered under a certain N2 pressure, for example, about 20 and 7 MPa for 10 and 15 mol% MgO, respectively, the evolutions of N and Si were suppressed. The thickness of the MHL became very small and at the same time the strength of the surface layer of the compact (which was normally less than that of the inside in the case of 0.1 MPa) became nearly the same value as that of the inside. At higher pressure, the strength of both surface layer and the inside decreased considerably. Some discussion was made on these results.

Hayashi, K.↗
NASA NTRS1987

Deformation and fracture of single-crystal and sintered polycrystalline silicon carbide produced by cavitation

An investigation was conducted to examine the deformation and fracture behavior of single-crystal and sintered polycrystalline SiC surfaces exposed to cavitation. Cavitation erosion experiments were conducted in distilled water at 25 C by using a magnetostrictive oscillator in close proximity (1 mm) to the surface of SiC. The horn frequency was 20 kHz, and the double amplitude of the vibrating disk was 50 microns. The results of the investigation indicate that the SiC (0001) surface could be deformed in a plastic manner during cavitation. Dislocation etch pits were formed when the surface was chemically etched. The number of defects, including dislocations in the SiC (0001) surface, increased with increasing exposure time to cavitation. The presence of intrinsic defects such as voids in the surficial layers of the sintered polycrystalline SiC determined the zones at which fractured grains and fracture pits (pores) were generated. Single-crystal SiC had superior erosion resistance to that of sintered polycrystalline SiC.

Miyoshi, Kazuhisa↗
NASA NTRS1988

Gravity and configurational energy induced microstructural changes in liquid phase sintering

Experiments were performed with W-Ni-Fe heavy alloys in order to measure the microstructural changes vs. position that occur in liquid-phase sintering under normal gravity. The experimentally observed segregation is less than the calculated equilibrium segregation due to the retarding effect from the rigid solid skeleton formed during sintering. These results improve understanding of microstructure, mechanical properties, component shape, and dimensional stability benefits that may be realized from low-gravity sintering.

Kipphut, C. M.↗
NASA NTRS1989

Improved silicon carbide for advanced heat engines. II - Pressureless sintering and mechanical properties of injection molded silicon carbide

The influence on density and strength of pressureless sintering in vacuum and argon environments has been evaluated with injection molded SiC materials. Main effects and two factor interactions of sintering (cycle variables temperature, time, heating rate, and atmosphere) were assessed. An improved understanding of the influence of the processing flaws and sintering conditions has been obtained. Strength and density have improved from a baseline level of 299 MPa (43.3 Ksi) and 94 pct of theoretical density to values greater than 483 MPa (70 Ksi) and 97 pct.

Whalen, Thomas J.↗
NASA NTRS1989

Deformation and fracture of single-crystal and sintered polycrystalline silicon carbide produced by cavitation

An investigation was conducted to examine the deformation and fracture behavior of single-crystal and sintered polycrystalline SiC surfaces exposed to cavitation. Cavitation erosion experiments were conducted in distilled water at 25 C by using a magnetostrictive oscillator in close proximity (1 mm) to the surface of SiC. The horn frequency was 20 kHz, and the double amplitude of the vibrating disk was 50 microns. The results of the investigation indicate that the SiC (0001) surface could be deformed in a plastic manner during cavitation. Dislocation etch pits were formed when the surface was chemically etched. The number of defects, including dislocations in SiC (0001) surface, increased with increasing exposure time to cavitation. The presence of intrinsic defects such as voids in the surficial layers of the sintered polycrystalline SiC determined the zones at which fractured grains and fracture pits (pores) were generated. Single-crystal SiC had superior erosion resistance to that of sintered polycrystalline SiC.

Miyoshi, Kazuhisa↗
NASA NTRS1990

An analysis of the contact sintering process in III-V solar cells

The possibility of eliminating the gross mechanical changes that take place during sintering while retaining the processes that reduce contact resistivity is investigated. Before considering the electrical aspects, however, it is necessary to understand the relevant metallurgy. As the sintering process proceeds in the InP-Au system, dramatic color changes occur that enable a precise measurement of the kinetics of each step. A detailed insight into the processes that control each stage in the InP-Au interaction has resulted. It is shown that contact sintering in the InP-Au system consists of three consecutive stages, each of which is controlled by a separate mechanism.

Weizer, Victor G.↗
NASA NTRS1989

Densification and coarsening during solid state sintering of ceramics: A review of the models. II - Grain growth

Two processes occur simultaneously during the sintering of a ceramic powder compact: densification and coarsening (or grain growth). Both processes have as their driving force the reduction of the excess free surface energy of the powder particles. Several different mechanisms of atom transport, operating concurrently or consecutively, may be responsible for the two processes. Algebraic, geometric and topological models have been proposed and refined in attempts to determine the mechanism, or mechanisms, responsible for densification under defined processing conditions. These efforts have met with varying degrees of success. Recently, it has become apparent that more attention must be paid to the coarsening processes during sintering. The models for both densification and coarsening during solid state sintering are reviewed with particular emphasis on their applicability to engineering ceramics.

Shaw, Nancy J.↗
NASA NTRS1991

Indirect measurement of the viscosity of the intergranular glass phase in yttria-sintered silicon nitride

Dense, sintered Si3N4 possesses a residual intergranular glass phase which softens at high temperatures, resulting in degradation of the ceramic's mechanical properties at high temperatures. An important parameter in the determination of the high temperature mechanical properties of sintered Si3N4 is the temperature-viscosity relationship of the intergranular glass. A method for indirectly measuring the intergranular glass viscosity at a given temperature using physical modelling of a two phase glass crystal microstructure and beam bending viscometry measurements of Si3N4 is described. Intergranular glass viscosities obtained by this method are presented for a yttria sintered Si3N4.

Dittmar, Mark B.↗
NASA NTRS1990

An analysis of the contact sintering process in III-V solar cells

The possibility of eliminating the gross mechanical changes that take place during sintering while retaining the processes that reduce contact resistivity is investigated. Before considering the electrical aspects, however, it is necessary to understand the relevant metallurgy. As the sintering process proceeds in the InP-Au system, dramatic color changes that enable a precise measurement of the kinetics of each step occur. A detailed insight into the processes that control each stage in the InP-Au interaction has resulted. It is shown that contact sintering in the InP-Au system consists of three consecutive stages, each of which is controlled by a separate mechanism.

Weizer, Victor G.↗
NASA NTRS1997

Performance Comparison Between NiH2 Dry Sinter and Slurry Electrode Cells

The electrical and thermal performance of dry sinter and slurry process electrode cells manufactured for the Hubble Space Telescope (HST) batteries have been characterized for a matrix of operating conditions over the temperature range from 14 to 86 F at various charge control levels. The dry sinter process electrode cells tested are similar to the onboard HST NiH2 cells. The slurry process electrode cells were developed to be less susceptible to electrode expansion and impedance changes with life. Both cell types were impregnated by the aqueous electrochemical process. Test conditions included standard capacity tests and electrical cycling using 96-minute cycling regimens incorporating gr depth-of-discharge (DOD) cycles. The dry sinter process electrodes have higher operating capacities to 1.20V/cell, but both electrode types have similar heat dissipation for the conditions tested. The results of the testing included cyclic heat generation during a typical 96-minute cycle, operating capacity data vs. cutoff voltage to generate a temperature-compensated voltage curve, and voltage characteristics suitable to develop a voltage prediction model. Analysis of data shows differences in the discharge voltage plateaus operating conditions evaluated. This is the basis for recommended changes in the battery charge control.

Armantrout, J. D.↗
NASA NTRS2004

Sintering of BaCe(0.85)Y(0.15)O3-(Beta) With/Without SrTiO Dopant

The sintering behavior of BaCe(0.85)Y(0.15)O3-(Beta) doped with SrTiO is described. Complete reaction and crystallization of perovskite phase by solid state was achieved by calcining at 1200 degrees C for 24 hours.Smaples were sintered at 1450 degrees C, 1550 degrees C, and 1650 degrees C. SrTiOsub3 enhanced sintering, while optimal dopant level was different for powders synthesized by solid state and co-precipitation. Both powders exhibit similar grain growth behavior.

Dynys, Fred↗
NASA NTRS2004

Sintering of BaCe(sub 0.85)Y(sub 0.15)O(sub 3-delta) with/without SrTiO3 Dopant

The perovskite composition, BaCe(sub 0.85)Y(sub 0.15)O(sub 3-delta), displays excellent protonic conduction at high temperatures making it a desirable candidate for hydrogen separation membranes. This paper reports on the sintering behavior of BaCe(sub 0.85)Y(sub 0.15)O(sub 3-delta) powders doped with SrTiO3. Two methods were used to synthesize BaCe(sub 0.85)Y(sub 0.15)O(sub 3-delta) powders: (1) solid state reaction and (2) wet chemical co-precipitation. Co-precipitated powder crystallized into the perovskite phase at 1000 C for 4 hrs. Complete reaction and crystallization of the perovskite phase by solid state was achieved by calcining at 1200 C for 24 hrs. Solid state synthesis produced a coarser powder with an average particle size of 1.3 microns and surface area of 0.74 sq m/g. Co-precipitation produced a finer powder with a average particle size of 65 nm and surface area of 14.9 sq m/g. Powders were doped with 1, 2, 5, and 10 mole % SrTiO3. Samples were sintered at 1450 C, 1550 C and 1650 C. SrTiO3 enhances sintering, optimal dopant level is different for powders synthesized by solid state and co-precipitation. Both powders exhibit similar grain growth behavior. Dopant levels of 5 and 10 mole % SrTiO3 significantly enhances the grain size.

Dynys, F.↗
NASA NTRS2004

Ceramic Interconnects with Low Sintering Temperature

Ceramic interconnects for use in solid oxide he1 cells are expected to operate between 900 to approximately 1000 C, sinter below 1400 C to allow co-firing and meet a number thermal mechanical requirements. The pervoskite type (ABO3) lanthanum chromite based materials have emerged as a leading candidate that will meet these criteria by varying the composition on the A and B sites. A need therefore exists to determine this material's temperature dependent electrical and mechanical properties with respect to these site substitutions. In this investigation oxide powders were prepared by the glycine-nitrate process. Ionic substitutions were carried out on A sites with Ca or Sr, and B sites with Co and Al, respectively. Only stoichiometric compositions were considered for the sake of stability. The powders and their ability to sinter were investigated by XRD, SEM, dilatometry and density measurements. The sintered materials were further examined by SEM, thermal expansion and electric conductivity measurements in order to elucidate the resulting microstructure, electrical and mechanical properties. In addition quantum mechanical calculations were performed to obtain insight into the effects of these dopants on the materials electronic band structure and lattice parameter.

Zhong, Zhi-Min↗
NASA NTRS2003

Sintering and Interface Strain Tolerance of Plasma-Sprayed Thermal and Environmental Barrier Coatings

Ceramic thermal and environmental barrier coatings will be more aggressively designed to protect gas turbine engine hot section SiC/SiC Ceramic Matrix Composite (CMC) components in order to meet future engine higher fuel efficiency and lower emission goals. A coating system consisting of a zirconia-based oxide topcoat (thermal barrier) and a mullite/BSAS silicate inner coat (environmental barrier) is often considered a model system for the CMC applications. However, the coating sintering, and thermal expansion mismatch between the zirconia oxide layer and the silicate environmental barrier/CMC substrate will be of major concern at high temperature and under thermal cycling conditions. In this study, the sintering behavior of plasma-sprayed freestanding zirconia-yttria-based thermal barrier coatings and mullite (and/or barium-strontium-aluminosilicate, i.e., BSAS) environmental barrier coatings was determined using a dilatometer in the temperature range of 1200-1500 C. The effects of test temperature on the coating sintering kinetics were systematically investigated. The plasma-sprayed zirconia-8wt.%yttria and mullite (BSAS) two-layer composite coating systems were also prepared to quantitatively evaluate the interface strain tolerance of the coating system under thermal cycling conditions based on the dilatomentry. The cyclic response of the coating strain tolerance behavior and interface degradation as a function of cycle number will also be discussed.

Zhu, Dongming↗
NASA NTRS2011

Solvent/Non-Solvent Sintering To Make Microsphere Scaffolds

A solvent/non-solvent sintering technique has been devised for joining polymeric microspheres to make porous matrices for use as drug-delivery devices or scaffolds that could be seeded with cells for growing tissues. Unlike traditional sintering at elevated temperature and pressure, this technique is practiced at room temperature and pressure and, therefore, does not cause thermal degradation of any drug, protein, or other biochemical with which the microspheres might be loaded to impart properties desired in a specific application. Also, properties of scaffolds made by this technique are more reproducible than are properties of comparable scaffolds made by traditional sintering. The technique involves the use of two miscible organic liquids: one that is and one that is not a solvent for the affected polymer. The polymeric microspheres are placed in a mold having the size and shape of the desired scaffold, then the solvent/non-solvent mixture is poured into the mold to fill the void volume between the microspheres, then the liquid mixture is allowed to evaporate. Some of the properties of the resulting scaffold can be tailored through choice of the proportions of the liquids and the diameter of the microspheres.

Laurencin, Cato T.↗
NASA NTRS2012

Multi-Scale Modeling of Liquid Phase Sintering Affected by Gravity: Preliminary Analysis

A multi-scale simulation concept taking into account impact of gravity on liquid phase sintering is described. The gravity influence can be included at both the micro- and macro-scales. At the micro-scale, the diffusion mass-transport is directionally modified in the framework of kinetic Monte-Carlo simulations to include the impact of gravity. The micro-scale simulations can provide the values of the constitutive parameters for macroscopic sintering simulations. At the macro-scale, we are attempting to embed a continuum model of sintering into a finite-element framework that includes the gravity forces and substrate friction. If successful, the finite elements analysis will enable predictions relevant to space-based processing, including size and shape and property predictions. Model experiments are underway to support the models via extraction of viscosity moduli versus composition, particle size, heating rate, temperature and time.

Olevsky, Eugene↗
NASA NTRS2017

Nuclear Rocket Ceramic Metal Fuel Fabrication Using Tungsten Powder Coating and Spark Plasma Sintering

Nuclear thermal propulsion is an enabling technology for crewed Mars missions. An investigation was conducted to evaluate spark plasma sintering (SPS) as a method to produce tungsten-depleted uranium dioxide (W-dUO2) fuel material when employing fuel particles that were tungsten powder coated. Ceramic metal fuel wafers were produced from a blend of W-60vol% dUO2 powder that was sintered via SPS. The maximum sintering temperatures were varied from 1,600 to 1,850 C while applying a 50-MPa axial load. Wafers exhibited high density (>95% of theoretical) and a uniform microstructure (fuel particles uniformly dispersed throughout tungsten matrix).

Barnes, M. W.↗
DOE OSTI2025

High-temperature nanoindentation creep studies on castable and sintered nanostructured low-activation ferritic-martensitic alloys

In this article, we present the creep characteristics of two reduced activation ferritic-martensitic steels of identical starting compositions formed by different fabrication routes: a nanostructured ferritic alloy commonly referred to as a castable nanostructured alloy (CNA) and a sintered nanostructured alloy (SNA) variant. Through a series of nanoindentation experiments spanning a temperature range of 25 °C to 650 °C, with a maximum load of 100 mN, we find creep behaviors in the cast and sintered materials to be remarkably similar. The creep stress exponent (n) for CNA and SNA were found to be in the range of 8–35 and the activation volume was ∼14–42b 3 , underscoring a dominance of dislocation-mediated mechanisms in both alloys. Notably, we observed a decline in the creep stress exponent with increasing temperature, attributable to the heightened influence of thermally activated dislocations. This phenomenon suggests a potential transition in the deformation mechanism towards a thermally activated dislocation climb process, significantly impacting the observed creep behavior.

36 MATERIALS SCIENCE↗