Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Shape memory alloy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Rapid solidified ductile Cu-Al-Mn ribbon and its elastocaloric potential

Abstract Cu-Al-Mn alloys display martensitic transformation over a wide range of temperatures. In addition to low cost, this alloy is known for its low transformation stress with reasonable latent heat favoring elastocaloric applications. However, the ductility of Cu-Al-Mn can be limited owing to ordering and intergranular fracture. Through rapid solidification by melt spinning, we show that Cu-Al-Mn ribbon can be made highly ductile (greater than 8% tensile strain in the as-spun state and 10% tensile strain after heat treatment). The ductility of the melt-spun ribbon is related to the suppression of L2 1 ordering that is characterized through magnetic property measurement. Heat treatment of the ribbon promotes bamboo grain formation, and the latent heat is increased to 6.4 J g −1 . Under tensile conditions, we show that the ribbon exhibited about 4 °C temperature change (4.4 °C on heating and 4.2 °C on cooling from 6.3% strain).

36 MATERIALS SCIENCE↗
DOE OSTI2020

Mapping of Texture and Phase Fractions in Heterogeneous Stress States during Multiaxial Loading of Biomedical Superelastic NiTi

Thermoelastic deformation mechanisms in polycrystalline biomedical-grade superelastic NiTi are spatially mapped using in situ neutron diffraction during multiaxial loading and heating. The trigonal R-phase is formed from the cubic phase during cooling to room temperature and subsequently deforms in compression, tension, and torsion. The resulting R-phase variant microstructure from the variant reorientation and detwinning processes are equivalent for the corresponding strain in tension and compression, and the variant microstructure is reversible by isothermal loading. The R-phase variant microstructure is consistent between uniaxial and torsional loading when the principal stress directions of the stress state are considered (for the crystallographic directions observed here). The variant microstructure evolution is tracked and the similarity in general behavior between uniaxial and torsional loading, in spite of the implicit heterogeneous stress state associated with torsional loading, pointed to the ability of the reversible thermoelastic transformation in NiTi to accommodate stress and strain mismatch with deformation. This ability of the R-phase, despite its limited variants, to accommodate stress and strain and satisfy strain incompatibility in addition to the existing internal stresses has significance for reducing irrecoverable deformation mechanisms during loading and cycling through the phase transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Determining Multi-Component Phase Diagrams with Desired Characteristics Using Active Learning

Herein, we demonstrate how to predict and experimentally validate phase diagrams for multi-component systems from a high-dimensional virtual space of all possible phase diagrams involving several elements based on small existing experimental data. The experimental data for bulk phases for known systems represents a sampling from this space, and screening the space allows multi-component phase diagrams with given design criteria to be built. This approach uses machine learning methods to predict phase diagrams and Bayesian experimental design to minimize experiments for refinement and validation, all within an active learning loop. The approach is proven by predicting and synthesizing the ferroelectric ceramic system (1-ω)(Ba 0.61 Ca 0.28 Sr 0.11 TiO 3 )-ω(BaTi 0.888 Zr 0.0616 Sn 0.0028 Hf 0.0476 O 3 ) with a relatively high transition temperature and triple point, as well as the NiTi-based pseudo-binary phase diagram (1-ω)(Ti 0.309 Ni 0.485 Hf 0.20 Zr 0.006 )-ω(Ti 0.309 Ni 0.485 Hf 0.07 Zr 0.068 Nb 0.068 ) designed for high transition temperature (ω ≤ 1). Each phase diagram is validated and optimized through only three new experiments. The complexity of these compounds is beyond the reach of today’s computational methods.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High performance Nb/TiNi nanocomposites produced by packaged accumulative roll bonding

Taking full advantage of intrinsic high strength of nano-reinforcements has been proven difficult in a composite until the concept of strain matching was experimental verified in a nanowire Nb/TiNi in-situ composite, which was obtained via solidifying eutectic Nb/TiNi and subsequent severe wire drawing. However, the volume fraction of the nano-reinforcement was dictated by eutectic reaction, which severely limited the development of high-performance composites. Here, the martensitic transformation nanocomposites were successfully acquired with increased volume fraction and changeable morphology of the nano-reinforcement through hot packaged ARB (PARB) and subsequent wire drawing. The nano-reinforcement with lamellar configuration in the composite could exhibit a large lattice strain of similar to 3.8%, which demonstrated the applicability and effectiveness of the strain matching principle in nano-lamellar composite. The obtained composites show a yield strength over 2.0 GPa and a quasi-linear elastic strain as larger as similar to 6.5% with adjustable apparent elastic modulus from 30 to 50 GPa.

42 ENGINEERING↗
DOE OSTI2020

Temperature-dependence of superelastic stress in nanocrystalline NiTi with complete transformation capability

Nanocrystalline (NC) NiTi were previously reported to obtain non-hysteretic superelasticity and nearly zero temperature-dependence of superelastic stresses. However, the influence of the non-transforming regions in the specimens was not ruled out. In this study, we fabricate NC NiTi specimens with grain size down to 15 nm by wire drawing and annealing. Our specimens have no detectable non-transforming regions and thus are of complete transformation capability. We demonstrate that the hysteretic superelasticity is observed in all specimens of different grain sizes and that the minimum temperature-dependence of superelastic stresses is 4.7 MPa/K. Possible reasons for the discrepancy have been discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Dynamics and structure of the B2→B19’ phase transformation in NiTi revealed through in situ 4D-STEM

The structural evolution of NiTi during the B2→B19’ martensitic phase transformation via thermal cycling is investigated using in situ four dimensional scanning transmission electron microscopy (4D-STEM). With 4D-STEM, we can directly visualize and quantify the nanoscale evolution of the martensitic structure on thermal cycling and also investigate the origin of diffuse scattering of NiTi in the pre-transitional state. Mapping of the martensite orientation and strain visualizes the progression of the transformation front and self-accommodation of the B19’ structure. Diffuse streaking and strain are measured in the pre-transitional austenite (B2) phase and demonstrate no localization or preferential directionality hinting that long-range homogeneous instability rather than nanoscale heterogeneities may be the origin of the pre-transitional anomalies in NiTi. Finally, it is revealed that NiTi does not reform the same martensite nanostructure on thermal cycling but does express similar features. This small variation is likely owing to transformation-induced dislocations.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Taming the Pseudoelastic Response of Nitinol Using Ion Implantation

Implantation of Ni 50.5 Ti 49.5 wire with 30 MeV Ni 6+ ions at doses (< 0.1 DPA) typically smaller than employed in the literature is shown to systematically alter the pseudoelastic response, with extrema in Berkovich nanoindentation load (+50%), hysteresis (–60%), and recoverable displacement (–19%) occurring at ~ 3.6 μm below the implantation surface. These extraordinary values are attributed to ~ 10 to 20 nm amorphous clusters that constrain the stress-induced B2-B19' phase transformation. This is substantiated by phase field simulations of crystalline-amorphous composites and molecular dynamics simulations of crystalline-vacancy cluster composites showing the spatial refinement of martensite caused by nm-scale defects. Finally, the results suggest that ion implantation may potentially expand the processing and performance space for NiTi, by creating amorphous defects at smaller length scales than dislocation substructures produced by conventional deformation processing.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A non-volatile thermal switch for building energy savings

Compared with traditional static insulation, a thermally switchable building envelope could reduce annual heating and cooling loads by intermittently coupling to the outside environment when beneficial. Here, we demonstrate a voltage-actuated, contact/non-contact thermal switch that meets the unique challenges of this application. The switch is non-volatile, consuming electricity only briefly while switching and none to hold steady state. The switch ratio is 12, the off state has a low effective thermal conductivity of 0.045 W m -1 K -1 , comparable to fiberglass insulation, and the performance is stable over 1,000 switching cycles. Numerical simulations using real-world climate data show that combining this thermal switch with a thermal storage layer in a building envelope can yield annual energy savings of 9%-55% (heating) and 17%-76% (air conditioning), depending on the climate zone. The greatest benefits are realized when the exterior temperature crosses well above and below the desired interior temperature within a single 24 h period.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Combinatorial Exploration and Mapping of Phase Transformation in a Ni–Ti–Co Thin Film Library

Combinatorial synthesis and high-throughput characterization of a Ni–Ti–Co thin film materials library are reported for exploration of reversible martensitic transformation. The library was prepared by magnetron co-sputtering, annealed in vacuum at 500 °C without atmospheric exposure, and evaluated for shape memory behavior as an indicator of transformation. Composition, structure, and transformation behavior of the 177 pads in the library were characterized using high-throughput wavelength dispersive spectroscopy (WDS), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and four-point probe temperature-dependent resistance (R(T)) measurements. A new, expanded composition space having phase transformation with low thermal hysteresis and Co > 10 at. % is found. Unsupervised machine learning methods of hierarchical clustering were employed to streamline data processing of the large XRD and XPS data sets. Through cluster analysis of XRD data, we identified and mapped the constituent structural phases. Finally, composition–structure–property maps for the ternary system are made to correlate the functional properties to the local microstructure and composition of the Ni–Ti–Co thin film library.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Role of nanoscale coherent precipitates on the thermo-mechanical response of martensitic materials (Final Report)

Coherent second phases can have a profound effect on the properties and performance of martensitic materials, and we lack a comprehensive, mechanistic understanding of the underlying processes. This limits our ability to rationally design second phases to tailor the response of martensitic materials. To address this situation, this project sought to develop a mechanistic, predictive understanding of the thermal and mechanical response of martensitic materials with nanoscale coherent heterogeneities. A synergistic combination of atomistic simulations and experiments was used to relate the local properties of each phase (in particular, their free energy landscape) and the material nanostructure (volume fraction, shape and size of second phase precipitates, and defects that may disrupt coherency) to the overall materials response. The focus was on second phases expected to induce phenomena or properties not otherwise achievable: second order martensitic transformation in SMAs, ultra-low stiffness, increased control of transition temperatures, and fatigue resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Hardenability and microstructural evolution of a precipitation strengthened Ni 50 Ti 21 Hf 25 Al 4 alloy

NiTi-based quaternary alloys are used in a variety of mechanical components, such as bearings, actuators, and dampers, owing to their good hardenability, wear resistance, and corrosion resistance. Additionally, one of the most notable characteristics of NiTi-based alloys is their shape memory effect and pseudoelastic properties. Connecting the macroscopic processing parameters employed in the design of new intermetallic alloys to the nanoscale structural characteristics dictating their behavior is crucial for improving their mechanical properties and expanding the spectrum of potential applications. Here, in this work, an arc melted Ni 50 Ti 21 Hf 25 Al 4 (at%) alloy was solution treated at 1050 °C followed by quenching and aging at 600 °C to investigate the effect of aging time on the microstructure and mechanical properties. Two types of nano-sized precipitates were observed and determined as face-centered orthorhombic H-phase (TiHf)Ni and L2 1 Heusler precipitates Ni 2 TiAl. The morphology and orientation of the H-phase were investigated using scanning and transmission electron microscopy (SEM and TEM), elucidating the coarsening kinetics and strengthening contribution of that phase to the intermetallic mechanical behavior. Following coarsening, the presence of Heusler nanoprecipitates was detected under overaged conditions through TEM imaging and nanobeam electron diffraction patterns. A peak hardness condition of 756 HV was achieved after 70 h of aging, indicating that the co-precipitation of H-phase and Heusler precipitates through a well-designed aging treatment can lead to optimal mechanical performance, thus elevating the alloy’s potential as a viable material for industrial applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effect of Melt-Spinning Parameters on the Structure and Properties of Ni 55.5 Mn 18.8 Ga 24 Si 1.7 Heusler Alloy Ribbons

Ni–Mn-based Heusler alloys are known to demonstrate magnetic shape memory and giant magnetocaloric effect (MCE). These effects depend on the phases, crystallographic and magnetic phase transitions, and the crystallographic texture characteristics. These structural characteristics, in turn, are a function of the processing parameters. In the current work, Ni 55.5 Mn 18.8 Ga 24 Si 1.7 Heusler alloy was processed by melt-spinning under a helium atmosphere. This process results in a fine microstructure. The ribbon that was produced with a narrower nozzle width, faster wheel speed, and higher cast temperature, indicating a faster cooling rate, had double the magnetic entropy change close to room temperature. However, the other ribbon demonstrated a large entropy change over a broader temperature range, extending its usability. The effect of the melt-spinning process parameters on the developing microstructure, crystallographic structure and texture, transformation temperatures, and the magnetic entropy change were studied to explain the difference in magnetocaloric behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Shape memory effect in metallic glasses

Shape memory effect (SME), mainly present in crystalline Ti-Ni alloys, is basically missing in metallic glasses (MGs) that lack the long-range periodic order of crystals. In this work, we report experimental results of SME in annealed MGs, in which the low-energy configuration state recovery is observed by both differential scanning calorimetry and X-ray photon correlation spectroscopy. We elucidate the origin of SME in MGs under the potential energy landscape framework, i.e., after annealing, the energy of MGs enters into a deep basin and atoms are located in the low-energy configuration state. Albeit deviating from their relative stable configurations by temperature changes, atoms in the annealed MGs tend to return to the low-energy atomic configurations along certain trajectories as pre-annealing temperature is approached, These results could extend the application of MGs as functional materials by directionally manipulating their energy states via annealing and rejuvenation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Martensitic transformation in superlattices of two non-transforming metals

A number of studies have shown that the coherent integration of a second non-transforming phase in martensitic materials results in unprecedented thermo-mechanical properties. We demonstrate the possibility of martensitic transformation by epitaxially combining two non-transforming materials, Mg (hexagonal closed packed) and MgLi (body centered cubic). Density functional theory calculations predict that MgLi/Mg superlattices undergo a transformation crystallographically equivalent to MgSc alloys and can be expected to result in finite temperature shape memory behavior. We predict the zero-temperature energy of the martensite phase to be 9.3 meV/atom lower than austenite for a 50–50 at. % MgLi/Mg nanolaminate, which is expected to result in a martensitic transformation temperature of approximately 150 K. This energy difference can be tuned between 4.9 and 18.1 meV/atom by varying the fraction of the pure Mg phase in the superlattice, potentially enabling the transformation from cryogenic to room and higher temperatures. While Li diffusion might limit the applications of the systems proposed, this work opens the door to a new approach to create martensitic materials.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗