Results for “Schlieren image” — Page 6

NASA NTRS2012

Analysis of Buzz in a Supersonic Inlet

A dual-stream, low-boom supersonic inlet designed for use on a small, Mach 1.6 aircraft was tested experimentally in the 8- by 6-Foot Supersonic Wind Tunnel (SWT) at the NASA Glenn Research Center (GRC). The tests showed that the inlet had good recovery and stable operation over large mass flow range. The inlet went into buzz at mass flows well below that needed for engine operation, and the experiments generated a wealth of data during buzz. High frequency response pressure measurements and high-speed schlieren videos were recorded for many buzz events. The objective of the present work was to use computational fluid dynamics (CFD) to predict some of the experimental data taken during buzz, compare those predictions to the experimental data, and to use both datasets to explain the physics of the buzz cycle. The calculations were done with the Wind-US CFD code using a second-order time-accurate differencing scheme and the SST turbulence model. Computed Mach number contours were compared with schlieren images, and ensemble-averaged unsteady pressures were compared to data. The results showed that the buzz cycle consisted partly of spike buzz, an unsteady oscillation of the main shock at the spike tip while the inlet pressure dropped, and partly of choked flow while the inlet repressurized. Most of the results could be explained by theory proposed by Dailey in 1954, but did not support commonly used acoustic resonance explanations.

Chima, Rodrick V.↗

NASA NTRS2012

Experimental Sonic Boom Measurements on a Mach 1.6 Cruise Low-Boom Configuration

A wind tunnel test has been conducted by Gulfstream Aerospace Corporation (GAC) to measure the sonic boom pressure signature of a low boom Mach 1.6 cruise business jet in the Langley Unitary Plan Wind Tunnel at Mach numbers 1.60 and 1.80. Through a cooperative agreement between GAC and the National Aeronautics and Space Administration (NASA), GAC provided NASA access to some of the experimental data and NASA is publishing these data for the sonic boom research community. On-track and off-track near field sonic boom pressure signatures were acquired at three separation distances (0.5, 1.2, and 1.7 reference body lengths) and three angles of attack (-0.26deg, 0.26deg, and 0.68deg). The model was blade mounted to minimize the sting effects on the sonic boom signatures. Although no extensive data analysis is provided, selected data are plotted to illustrate salient features of the data. All of the experimental sonic boom pressure data are tabulated. Schlieren images of the configuration are also included.

Wilcox, Floyd J., Jr.↗

NASA NTRS2014

Overview of NASA GRCs Green Propellant Infusion Mission Thruster Testing and Plume Diagnostics

The Green Propellant Infusion Mission (GPIM) is sponsored by NASA's Space Technology Mission Directorate (STMD) Technology Demonstration Mission (TDM) office. The goal of GPIM is to advance the technology readiness level of a green propulsion system, specifically, one using the monopropellant, AF-M315E, by demonstrating ground handling, spacecraft processing, and on-orbit operations. One of the risks identified for GPIM is potential contamination of sensitive spacecraft surfaces from the effluents in the plumes of AF-M315E thrusters. NASA Glenn Research Center (GRC) is conducting activities to characterize the effects of AF-M315E plume impingement and deposition. GRC has established individual plume models of the 22-N and 1-N thrusters that will be used on the GPIM spacecraft. The models describe the pressure, temperature, density, Mach number, and species concentration of the AF-M315E thruster exhaust plumes. The models are being used to assess the impingement effects of the AF-M315E thrusters on the GPIM spacecraft. The model simulations will be correlated with plume measurement data from Laboratory and Engineering Model 22-N, AF-M315E thrusters. The thrusters will be tested in a small rocket, altitude facility at NASA GRC. The GRC thruster testing will be conducted at duty cycles representatives of the planned GPIM maneuvers. A suite of laser-based diagnostics, including Raman spectroscopy, Rayleigh spectroscopy, Schlieren imaging, and physical probes will be used to acquire plume measurements of AFM315E thrusters. Plume data will include temperature, velocity, relative density, and species concentration. The plume measurement data will be compared to the corresponding simulations of the plume model. The GRC effort will establish a data set of AF-M315E plume measurements and a plume model that can be used for future AF-M315E applications.

green Propellants↗

NASA NTRS2014

The Green Propellant Infusion Mission Thruster Performance Testing for Plume Diagnostics

The Green Propellant Infusion Mission (GPIM) is sponsored by NASA's Space Technology Mission Directorate (STMD) Technology Demonstration Mission (TDM) office. The goal of GPIM is to advance the technology readiness level of a green propulsion system, specifically, one using the monopropellant, AF-M315E, by demonstrating ground handling, spacecraft processing, and on-orbit operations. One of the risks identified for GPIM is potential contamination of sensitive spacecraft surfaces from the effluents in the plumes of AF-M315E thrusters. NASA Glenn Research Center (GRC) is conducting activities to characterize the effects of AF-M315E plume impingement and deposition. GRC has established individual plume models of the 22-N and 1-N thrusters that will be used on the GPIM spacecraft. The model simulations will be correlated with plume measurement data from Laboratory and Engineering Model 22-N, AF-M315E thrusters. The thrusters are currently being tested in a small rocket, altitude facility at NASA GRC. A suite of diagnostics, including Raman spectroscopy, Rayleigh spectroscopy, and Schlieren imaging are being used to acquire plume measurements of AF-M315E thrusters. Plume data will include temperature, velocity, relative density, and species concentration. The plume measurement data will be compared to the corresponding simulations of the plume model. The GRC effort will establish a data set of AF-M315E plume measurements and a plume model that can be used for future AF-M315E applications.

Green Propellants↗

NASA NTRS2015

Plume and Shock Interaction Effects on Sonic Boom in the 1-foot by 1-foot Supersonic Wind Tunnel

The desire to reduce or eliminate the operational restrictions of supersonic aircraft over populated areas has led to extensive research at NASA. Restrictions are due to the disturbance of the sonic boom, caused by the coalescence of shock waves formed by the aircraft. A study has been performed focused on reducing the magnitude of the sonic boom N-wave generated by airplane components with a focus on shock waves caused by the exhaust nozzle plume. Testing was completed in the 1-foot by 1-foot supersonic wind tunnel to study the effects of an exhaust nozzle plume and shock wave interaction. The plume and shock interaction study was developed to collect data for computational fluid dynamics (CFD) validation of a nozzle plume passing through the shock generated from the wing or tail of a supersonic vehicle. The wing or tail was simulated with a wedgeshaped shock generator. This test entry was the first of two phases to collect schlieren images and off-body static pressure profiles. Three wedge configurations were tested consisting of strut-mounted wedges of 2.5- degrees and 5-degrees. Three propulsion configurations were tested simulating the propulsion pod and aft deck from a low boom vehicle concept, which also provided a trailing edge shock and plume interaction. Findings include how the interaction of the jet plume caused a thickening of the shock generated by the wedge (or aft deck) and demonstrate how the shock location moved with increasing nozzle pressure ratio.

Shock wave interaction↗

NASA NTRS2018

Computational and Experimental Study of Plume and Shock Interaction Effects on Sonic Boom in the NASA Ames 9x7 Supersonic Wind Tunnel

A wind tunnel test was performed in the NASA Ames 9x7 Supersonic Wind Tunnel focusing on the shock waves traveling through and interacting with an exhaust nozzle plume. This experimental study was conducted to develop and validate the CFD capability required to accurately include nozzle flow with impinging shock effects on near field and ground‐propagated sonic boom signatures. The model was made to be generic, and included a simple nozzle shape, two different aft decks, and a few generic horizontal tails. High pressure air was pumped through a nozzle at various nozzle pressure ratios (NPR) to represent the engine plume in flight. The three different aft body representations each created a different shock wave signature that passed through the plume. An aft deck configuration, where part of the aircraft shields the nozzle plume, was also tested. Retroreflective Background-Oriented Schlieren (RBOS) was used to obtain schlieren images of the flow field around the model and behind the model. This study compares wind tunnel data and numerical simulations conducted by the NASA Tetrahedral Unstructured Software System CFD code, USM3D.

Winski, Courtney S.↗

NASA NTRS2019

Examination of Annular-Electrode Spark Discharges in Flowing Oxygen – Experimental Nuances

Microsecond sparks and the resulting plume of hot gas/plasma were examined against a parametric pressure-distance matrix. Schlieren imaging is used to capture the spatial and temporal location of spark discharge exhaust for two milliseconds. Low pressure and larger gap widths created the largest size and intensity signal for the spark-affected plumes. Experimental exit-plume velocities trend well with analytic predictions using a mean pressure between the chamber and atmospheric conditions. Due to the quadratic relation of the annulus area and gap width, larger gap width velocities are more accurately represented by analytic predictions using atmospheric pressure as the larger exit area restricts the flow less. The same pressure adjustment, when applied to breakdown voltages, improves data alignment with Paschen’s Curve.

Darren C Tinker↗

NASA NTRS2019

Laboratory Scale Testing of Ignition Overpressure for Space Vehicle Launch Pad Environments

A scale model of a NASA representative space vehicle is used to develop a refined estimate of the transient pressure loads that are expected to form at the base of the vehicle in the event of a vapor cloud explosion. Flammable vapor clouds are known to form prior to engine startup due to the significant amount of unburned hydrogen that is ejected from the combustion chamber. In the event of a vapor cloud explosion, the vehicle and payload must be able to withstand the resulting overpressure waves. The study comprises an array of pressure sensors located along the base heat shield of the scale model space vehicle as well as the interior wall and throat plug plane of the solid rocket booster. A spark source generator is used to simulate the overpressure wave produced by a vapor cloud explosion while measurements are acquired with and without the effect of a mobile launcher. Time- resolved schlieren images of the simulated vapor cloud explosion reveal the path and impact of both the initial wave and several reflected waves on the various components at the base of the space vehicle. In some instances, the reflected waves superpose to create waves that are higher in amplitude than the initial overpressure wave. A time frequency analysis of the pressure waveforms measured inside the solid rocket booster reveal a ring down tone corresponding to a standing wave that is four times the length of the nozzle.

Tinney, Charles E.↗

NASA NTRS2019

Space Launch System Booster Separation Supersonic Powered Testing with Surface and Off-Body Measurements

A wind tunnel test was run in the NASA Langley Unitary Plan Wind Tunnel simulating the separation of the two solid rocket boosters (SRB) from the core stage of the NASA Space Launch System (SLS). The test was run on a 0.9% scale model of the SLS Block 1B Cargo (27005) configuration and the SLS Block 1B Crew (28005) configuration at a Mach of 4.0. High pressure air was used to simulate plumes from the booster separation motors located at the nose and aft skirt of the two boosters. Force and moment data were taken on both SRBs and on the core stage. Schlieren still photos and video were recorded throughout testing. A set of points were acquired using Cross-correlation Doppler Global Velocimetry (CCDGV) readings to get 3 component velocity measurements between the core and the left-hand SRB. The CCDGV laser was utilized to record flow visualization in the same location, between the core and the left-hand SRB. Pressure Sensitive Paint data were taken on a separate set of runs. Computational Fluid Dynamics (CFD) runs were computed on a subset of the wind tunnel data points for comparison. A combination of the force/moment, CCDGV and Pressure Sensitive Paint (PSP) data (as well as schlieren images) at the CFD-specified test conditions will be used te the CFD simulations that will be used to build an SLS booster separation database flight conditions.

Winski, Courtney S.↗

NASA NTRS2019

High-Speed Schlieren Analysis of Retropropulsion Jet in Mach 10 Flow

High-speed schlieren imaging of a 5-in.-diam, 70° sphere-cone model with a single centerline 15° half-angle nozzle was performed in a Mach 10 flow. Image sequences captured at 100 kHz were obtained with the nozzle plugged (fully blunted model), no nozzle flow, and with nozzle flow over a range of supply pressures. The freestream unit Reynolds number was kept constant for all runs at3.38×106m−1. Time-average information pertaining to the location, width, and stand-off distance of the bow shock, interface, terminal shock, and triple point as a function of jet pressure ratio are presented based on analysis of covariance images from each run. Measurement of jet plume boundary shape as a function of jet pressure ratio is also presented. Analyses of frequency content associated with the jet structure are shown, as are results of the proper orthogonal decomposition of these data. For all runs with nozzle flow, a dominant fundamental frequency of 2 kHz was observed. Finally, a discussion of bow shock unsteadiness resulting from interaction with freestream disturbances for the blunted and no nozzle flow is provided, as is a discussion on the formation of weak waves emanating from the bow shock resulting from this interaction.

Brett F Bathel↗

NASA NTRSDate not supplied

Some Effects of Tunnel Noise on Cylinder-Induced Mach 6 Transitional Shock Wave Boundary Layer Interactions

Experiments were conducted on a cylinder-induced shock wave boundary layer interaction (SBLI)as its state was brought through transition using a combination of boundary layer trips and Reynolds number sweep. A baseline case with no trips was also examined. The measurements were made in a Mach 6 freestream in the well-characterized Actively Controlled Expansion tunnel, which demonstrated a near tripling in fluctuation levels with unit Reynolds number increase from 3.0 to 3.5 million per meter. Surface oil flow and schlieren images suggested the jump in freestream noise served as the impetus for SBLI transition since the flow separation distance began to decrease as the Reynolds number progressed through those conditions. Likewise, surface mounted Kulite® pressure transducers indicated a rise in surface pressure fluctuations as well as initial growth in the instability responsible for transitioning the boundary layer within the interaction. Finally, heat transfer rates within the tripped SBLI were shown to be affected by the jump in freestream disturbance levels.

Andrew N Leidy↗

NASA NTRSDate not supplied

Space Launch System Booster Separation Supersonic Powered Testing with Surface and Off-body Measurements

A wind tunnel test was run in the NASA Langley Unitary Plan Wind Tunnel simulating the separation of the two solid rocket boosters (SRB) from the core stage of the NASA Space LaunchSystem (SLS). The test was run on a 0.9% scale model of the SLS Block 1B Cargo (27005) configuration and the SLS Block 1B Crew (28005) configuration at a Mach of 4.0. The SRBs weremounted separately from the core, and could be pitched, yawed, and translated in the X, Y, andZ directions relative to the core. High pressure air was used to simulate plumes from the booster separation motors located at the nose and aft skirt of the two boosters. Force and moment data were taken on both SRBs and on the core stage. Schlieren still photos and video were recorded throughout testing. A set of points were acquired using Cross-correlation Doppler Global Velocimetry (CCDGV) readings to get 3 component velocity measurements between the core and the left-hand SRB. The CCDGV laser was utilized to record flow visualization in the same location, between the core and the left-hand SRB. Pressure Sensitive Paint (PSP) data were taken on a separate set of runs. Computational Fluid Dynamics (CFD) runs were computed on a subset of the wind tunnel data points for comparison. A combinationof the force and moment, CCDGV, and PSP data (as well as schlieren images) at the CFD-specified test conditions will be used to validate the CFD simulations that will be used to build an SLS booster separation database at flight conditions.

SLS↗

NASA NTRSDate not supplied

Analysis of the Amplitude Response of a Two-Point and a Two-Line/Multi-Point Focused Laser Differential Interferometer

Experiments were performed with two different focused laser differential interferometer (FLDI) instruments to assess the amplitude response of each instrument to a traveling shock-wave generated by a laser spark. The first FLDI instrument generated two measurement points, with each measurement point providing sensitivity to density fluctuations induced by the shockwave. By performing a cross-correlation between the signals obtained from each measurement point, the phase velocity of density fluctuations can be obtained. The second FLDI instrument generated two measurement lines that are oriented either parallel or orthogonal to the shockwave direction of travel with the resulting interference pattern sampled at multiple equally-spaced points along each line. As a result, this instrument provides density fluctuation measurement capability at multiple points simultaneously. When the measurement lines are oriented parallel to the shockwave direction of travel, the phase velocity, rate of change of the phase velocity, and acceleration of density fluctuations traveling along each line can be obtained by performing a cross-correlation between points along a single line. When the measurement lines are oriented orthogonal to the shockwave direction of travel, the spatially-varying phase velocity can be obtained by performing a cross-correlation between points at the same relative location on each measurement line. Computations of the shockwave generated by the laser spark are used to simulate the response of each instrument and are compared to the experimental results. High-speed Schlieren imaging has also been performed and is compared with the FLDI measurements and computational results.

Focused Laser Differential Interferometer↗

NASA NTRSDate not supplied

Nearfield Anisotropic Mesh Adaptation for the Third AIAA Sonic Boom Workshop

Sonic boom prediction is critical for the development of low-boom supersonic aircraft and encouraging a replacement of the overland commercial supersonic ban with a certification standard. The Third AIAA Sonic Boom Workshop nearfield test cases provide a unique opportunity to review anisotropic adaptive-mesh strategies for complex geometries with important propulsion interaction effects. Anisotropic metrics formulated to control estimated Mach interpolation and integrated nearfield pressure signature (goal-oriented) errors are compared with the results obtained on workshop-provided meshes. Detailed flow solutions and mesh renderings are combined with computational schlieren images to reveal the complex interactions present in a shock-plume interaction wind tunnel model and a prototype of the Low-Boom Flight Demonstrator. A favorable comparison of independent implementations of the entire simulation process provides evidence that each process is implemented correctly and sets a solid foundation for confidence in the nearfield prediction of each method.

sonic boom↗

NASA NTRSDate not supplied

Analysis of the Amplitude Response of a Two-Point and a Multi-Point Focused Laser Differential Interferometer

Experiments were performed with two different focused laser differential interferometer (FLDI) instruments to assess the relative amplitude response of each instrument to a traveling shockwave generated by a laser spark in air. The first FLDI instrument generated two slightly-separated measurement points, with each measurement point providing sensitivity to density fluctuations induced by the shockwave. By performing a cross-correlation between the signals obtained from each measurement point, the phase velocity of density fluctuations can be obtained. The second FLDI instrument generated a measurement line that was oriented parallel to the shockwave direction of travel with the resulting interference pattern sampled at multiple equally-spaced points along the line. As a result, this instrument provides density fluctuation measurement capability at multiple points simultaneously. When the measurement line is oriented parallel to the shockwave direction of travel, the phase velocity, rate of change of the phase velocity, and acceleration of density fluctuations traveling along each line can be obtained by performing a cross-correlation between points along the line. Numerical computations of the shockwave generated by the laser spark are used to simulate the response of each instrument and are compared to the experimental results. High-speed schlieren imaging has also been performed and is compared with the FLDI measurements and computational results.

Brett F. Bathel↗

NASA NTRSDate not supplied

Analysis of the Amplitude Response of a Two-Point and a Multi-Point Focused Laser Differential Interferometer

Experiments were performed with two different focused laser differential interferometer (FLDI) instruments to assess the relative amplitude response of each instrument to a traveling shockwave generated by a laser spark in air. The first FLDI instrument generated two slightly-separated measurement points, with each measurement point providing sensitivity to density fluctuations induced by the shockwave. By performing a cross-correlation between the signals obtained from each measurement point, the phase velocity of density fluctuations can be obtained. The second FLDI instrument generated a measurement line that was oriented parallel to the shockwave direction of travel with the resulting interference pattern sampled at multiple equally-spaced points along the line. As a result, this instrument provides density fluctuation measurement capability at multiple points simultaneously. When the measurement line is oriented parallel to the shockwave direction of travel, the phase velocity, rate of change of the phase velocity, and acceleration of density fluctuations traveling along each line can be obtained by performing a cross-correlation between points along the line. Numerical computations of the shockwave generated by the laser spark are used to simulate the response of each instrument and are compared to the experimental results. High-speed schlieren imaging has also been performed and is compared with the FLDI measurements and computational results.

Interferometry↗

NASA NTRS2021

Boundary Layer Instabilities Over a Cone-Cylinder-Flare Model at Mach 6

Computations are performed to investigate the boundary-layer instabilities over a sharp cone-cylinder-flare model at zero degrees angle of attack. The model geometry and the flow conditions are selected to match the experiments conducted in the Boeing/AFOSR Mach 6 Quiet Tunnel (BAM6QT) at Purdue University. The geometry consists of a nominally sharp 5-degree half-angle cone, followed by a cylindrical segment and then a 10-degree flare. An axisymmetric separation bubble is generated as a result of the laminar shock/boundary-layer interaction in the cylinder-flare region. The comparison of the laminar flow solution and the schlieren images shows a remarkable agreement between the respective locations of both the boundarylayer edge and the reattachment shock. The predicted heat flux distribution is also in agreement with the measured values downstream of the reattachment location. The analysis of convective and global instabilities is performed for flare half angles equal to 8, 10, and 12 degrees and nosetip radii equal to 0.1, 1, and 5 mm. The linear amplification of first and second Mack mode instabilities that begin to amplify in the cone region are computed with a combination of the parabolized stability equations (PSE) and the harmonic linearized Navier-Stokes equations (HLNSE). The predicted frequency spectra of the surface pressure fluctuations associated with both planar and oblique instability waves are compared with the measured spectra at the various locations of the PCB and Kulite sensors. The comparison shows that the computational analysis captures the distinct lobes within the disturbance amplification spectra measured in the experiments, but some differences in amplification characteristics are noted at low frequencies. Overall, the oblique disturbances are found to be more amplified than the planar disturbances. To our knowledge, this represents the first successful comparison between convective instability analysis and measured surface pressure fluctuations for a hypersonic configuration with a separation bubble. Finally, the global instability analysis shows that the laminar flow becomes supercritical for flare half angles larger than 8 degrees. The unstable global mode for the experimental configuration of a 10 degrees flare and a sharp nosetip cone corresponds to a stationary three-dimensional disturbance that is concentrated in the recirculation region and achieves its maximum growth rate for an azimuthal wavenumber of 5.

Boundary layer transition↗

NASA NTRS2022

Boundary Layer Instabilities Over a Cone-Cylinder-Flare Model at Mach 6

Computations are performed to investigate the boundary-layer instabilities over a sharp cone-cylinder-flare model at zero degrees angle of attack. The model geometry and the flow conditions are selected to match the experiments conducted in the Boeing/AFOSR Mach 6 Quiet Tunnel (BAM6QT) at Purdue University. The geometry consists of a nominally sharp 5-degree half-angle cone, followed by a cylindrical segment and then a 10-degree flare. An axisymmetric separation bubble is generated as a result of the laminar shock/boundary-layer interaction in the cylinder-flare region. The comparison of the laminar flow solution and the schlieren images shows a remarkable agreement between the respective locations of both the boundarylayer edge and the reattachment shock. The predicted heat flux distribution is also in agreement with the measured values downstream of the reattachment location. The analysis of convective and global instabilities is performed for flare half angles equal to 8, 10, and 12 degrees and nosetip radii equal to 0.1, 1, and 5 mm. The linear amplification of first and second Mack mode instabilities that begin to amplify in the cone region are computed with a combination of the parabolized stability equations (PSE) and the harmonic linearized Navier-Stokes equations (HLNSE). The predicted frequency spectra of the surface pressure fluctuations associated with both planar and oblique instability waves are compared with the measured spectra at the various locations of the PCB and Kulite sensors. The comparison shows that the computational analysis captures the distinct lobes within the disturbance amplification spectra measured in the experiments, but some differences in amplification characteristics are noted at low frequencies. Overall, the oblique disturbances are found to be more amplified than the planar disturbances. To our knowledge, this represents the first successful comparison between convective instability analysis and measured surface pressure fluctuations for a hypersonic configuration with a separation bubble. Finally, the global instability analysis shows that the laminar flow becomes supercritical for flare half angles larger than 8 degrees. The unstable global mode for the experimental configuration of a 10 degrees flare and a sharp nosetip cone corresponds to a stationary three-dimensional disturbance that is concentrated in the recirculation region and achieves its maximum growth rate for an azimuthal wavenumber of 5.

Hydrodynamic instability↗