Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SURFACE ROUGHNESS EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Passive microwave sensing of soil moisture content: Soil bulk density and surface roughness

Microwave radiometric measurements over bare fields of different surface roughnesses were made at the frequencies of 1.4 GHz, 5 GHz, and 10.7 GHz to study the frequency dependence as well as the possible time variation of surface roughness. The presence of surface roughness was found to increase the brightness temperature of soils and reduce the slope of regression between brightness temperature and soil moisture content. The frequency dependence of the surface roughness effect was relatively weak when compared with that of the vegetation effect. Radiometric time series observation over a given field indicated that field surface roughness might gradually diminish with time, especially after a rainfall or irrigation. This time variation of surface roughness served to enhance the uncertainty in remote soil moisture estimate by microwave radiometry. Three years of radiometric measurements over a test site revealed a possible inconsistency in the soil bulk density determination, which turned out to be an important factor in the interpretation of radiometric data.

Wang, J. R.↗
NASA NTRS1984

Cold-air performance of compressor-drive turbine of department of energy upgraded automobile gas turbine engine. 3: Performance of redesigned turbine

The aerodynamic performance of a redesigned compressor drive turbine of the gas turbine engine is determined in air at nominal inlet conditions of 325 K and 0.8 bar absolute. The turbine is designed with a lower flow factor, higher rotor reaction and a redesigned inlet volute compared to the first turbine. Comparisons between this turbine and the originally designed turbine show about 2.3 percentage points improvement in efficiency at the same rotor tip clearance. Two versions of the same rotor are tested: (1) an as cast rotor, and (2) the same rotor with reduced surface roughness. The effect of reducing surface roughness is about one half percentage point improvement in efficiency. Tests made to determine the effect of Reynolds number on the turbine performance show no effect for the range from 100,000 to 500,000.

Roelke, R. J.↗
NASA NTRS2000

Azimuth variation in microwave scatterometer and radiometer data over Antarctica

In this paper, we explore the use of NASA scatterometer (NSCAT) data, European remote sensing (ERS) advanced microwave instrument (AMI) scatterometer mode data, and special sensor microwave/imager (SSM/I) data to study surface roughness effects in Antarctica. All three sensors provide strong evidence of azimuth modulation, which is correlated with the surface slope environment and results in a katabatic wind flow regime.

azimuthal↗
NASA NTRS2007

RadSTAR L-Band Imaging Scatterometer: Performance Assessment

RadSTAR is an instrument development program aimed at combining a radiometer and a scatterometer system into a highly compact configuration that uses a single, electronically scanned antenna to provide co-located and simultaneous measurements of emission and backscatter for airborne and spaceborne applications [I]. The program was designed to map soil moisture and ocean salinity, both important components of the water cycle, and to map sea ice density and thickness, an important factor in ocean-atmosphere heat exchange in Polar Regions. The accuracy in estimation of these and a number of other Earth science parameters can be greatly enhanced by providing the co-aligned radar/radiometer microwave measurements. For instance, radiometer estimates of soil moisture from soil emission are affected by emission from vegetation, and from the roughness of the surface. Complementary measurements using the scatterometer can be used to evaluate the vegetation and surface roughness effects. Hence, the combined observations can provide an improved estimate. As with soil moisture, the ocean salinity is a function of the microwave emission from the sea surface temperature (SST) and sea roughness. There, the addition of radar backscatter measurements of sea roughness enables the correction of the emissivity and provide more accurate estimates of ocean salinity. Similar arguments can be made for other important Earth science parameters. This paper discusses the RadSTAR program, the radar system design, calibration, and digital beamforming techniques, and presents preliminary analysis of the data collected during the test flights. The data sets obtained during the flights and during the radar calibration in the anechoic chamber are also employed to asses the performance of the radar. The paper also discusses the Digital Beamforming Synthetic Aperture Radar (DBSAR) processor, a real-time processor recently developed for the LIS instrument which enables beam synthesis, fine resolutions, and large swaths.

Rincon, Rafael↗
NASA NTRS1981

An experimental investigation of silicon wafer surface roughness and its effect on the full strength of plated metals

Plated silicon wafers with surface roughness ranging from 0.4 to 130 microinches were subjected to tensile pull strength tests. Electroless Ni/electroless Cu/electroplated Cu and electroless Ni/electroplated Cu were the two types of plate contacts tested. It was found that smoother surfaces had higher pull strength than rougher, chemically etched surfaces. The presence of the electroless Cu layer was found to be important to adhesion. The mode of fracture of the contact as it left the silicon was studied, and it was found that in almost all cases separation was due to fracture of the bulk silicon phase. The correlation between surface roughness and mode of contact failure is presented and interpreted.

Spiers, G. D.↗
NASA NTRSDate not supplied

The Effect of Boundary Layer Character on Stochastic Rotor Blade Vortex Shedding Noise

This work illustrates the effect of a rotor blade’s boundary layer on the broadband LBL-VS self-noise emitted from an optimum hovering rotor through experimental and multi-fidelity computational studies. Blade surface roughness effects associated with different manufacturing techniques and the effect of adding a boundary layer trip were shown to decrease LBL-VS noise by upwards of 30 dB at the frequency of maximum emission with a slight penalty in aerodynamic performance when compared with smooth rotor blades. Low-fidelity 2-D viscous flow analysis verified the presence of laminar separation bubbles on the rotor blades which are responsible for LBL-VS noise. Three high-fidelity lattice-Boltzmann simulations were conducted with different wall-functions to predict the boundary layer character correspondent to their experimental counterpart and the resultant presence or absence of LBL-VS noise. Excellent aerodynamic and aeroacoustic agreement was seen between the lattice-Boltzmann simulations and the experimental data for the cases with surface roughness and the boundary layer trip, with the broadband noise results from the simulation with fully turbulent wall-functions diverging from the experimental results above 5 kHz. The transitional wall-function simulation which emulated the smooth experimental blades underpredicted thrust by 14% and broadband noise by a minimum of 10 dB with an accurately predicted broadband noise trend.

Christopher S Thurman↗
NASA NTRS1996

Applications of an Energy Transfer Model to Three Problems in Planetary Regoliths: The Solid-State Greenhouse, Thermal Beaming, and Emittance Spectra

Several problems of interest in planetary infrared remote sensing are investigated using a new radiative-conductive model of energy transfer in regoliths: the solid-state greenhouse effect, thermal beaming, and reststrahlen spectra. The results of the analysis are as follows: (1) The solid-state greenhouse effect is self-limiting to a rise of a few tens of degrees in bodies of the outer solar system. (2) Non-Lambertian directional emissivity can account for only about 20% of the observed thermal beaming factor. The remainder must have another cause, presumably surface roughness effects. (3) The maximum in a reststrahlen emissivity spectrum does not occur exactly at the Christiansen wavelength where, by definition, the real part of the refractive index equals one, but rather at the first transition minimum in reflectance associated with the transition from particle scattering being dominated by volume scattering to that dominated by strong surface scattering. The transparency feature is at the second transition minimum and does not require the presence of a second band at longer wavelength for its occurance. Subsurface temperature gradients have only a small effect on emissivity bands.

Hapke, Bruce↗
NASA NTRS1985

Lubrication of nonconformal contacts

Minimum film thickness results for piezoviscous-rigid regime of lubrication are developed for a compressible Newtonian fluid with Roelands viscosity. The results provide a basis for the analysis and design of a wide range of machine elements operating in the piezoviscous-rigid regime of lubrication. A new numerical method of calculating elastic deformation in contact stresses is developed using a biquadratic polynomial to approximate the pressure distribution on the whole domain analyzed. The deformation of every node is expressed as a linear combination of the nodal pressures whose coefficients can be combined into an influence coefficient matrix. This approach has the advantages of improved numerical accuracy, less computing time and smaller storage size required for influence matrix. The ideal elastohydrodynamic lubrication is extended to real bearing systems in order to gain an understanding of failure mechanisms in machine elements. The improved elastic deformation calculation is successfully incorporated into the EHL numerical scheme. Using this revised numerical technique and the flow factor model developed by Patir and Cheng (1978) the surface roughness effects on the elastohydrodynamic lubrication of point contact is considered. Conditions typical of an EHL contact in the piezoviscous-elastic regime entrained in pure rolling are investigated. Results are compared with the smooth surface solutions. Experiments are conducted to study the transient EHL effects in instrument ball bearings.

Jeng, Y. R.↗
NASA NTRS1978

Dynamics of short eccentric plain seals with high axial Reynolds number

Plain seals with high axial flow rates produce large stiffness and damping coefficients that can help stabilize high-speed rotating machinery. When the shaft is eccentric in the seal, a Bernoulli effect low-pressure region occurs on the large-clearance side of the shaft. A fluid-restoring force tends to center the shaft and reduce vibrations. This work extends the previous theory for short plain centered seals to large eccentricities using a perturbation analysis. Surface roughness effects are also included. An analysis of seals used in the Space Shuttle main engine hydrogen fuel turbopump indicates the desirability of plain seals over the labyrinth type. Experimental results confirm this.

Allaire, P. E.↗
NASA NTRS1982

The effects of varying surface roughness on aerodynamic and aeolian processses

The investigation of aeolian processes on Earth and Mars using wind tunnel simulations is described. The effect of variations in surface roughness on aerodynamic and aeolian processes was examined. Friction velocity ratios, wind friction threshold speeds, particle flux, and total flux were determined for various sand depths, degrees of surface roughness, and heights above a pebble bed.

Reding, L. M.↗
NASA NTRS1976

Remote sensing of soil moisture with microwave radiometers

Results are presented that were derived from measurements made by microwave radiometers during the March 1972 and February 1973 flights of National Aeronautics and Space Administration (NASA) Convair-9900 aircraft over agricultural test sites in the southwestern part of United States. The purpose of the missions was to study the use of microwave radiometers for the remote sensing of soil moisture. The microwave radiometers covered the 0.8- to 21-cm wavelength range. The results show a good linear correlation between the observed microwave brightness temperature and moisture content of the 0- to 1-cm layer of the soil. The results at the largest wavelength (21 cm) show the greatest sensitivity to soil moisture variations and indicate the possibility of sensing these variations through a vegetative canopy. The effect of soil texture on the emission from the soil was also studied and it was found that this effect can be compensated for by expressing soil moisture as a percent of field capacity for the soil. The results were compared with calculations based on a radiative transfer model for layered dielectrics and the agreement is very good at the longer wavelengths. At the shorter wavelengths, surface roughness effects are larger and the agreement becomes poorer.

Schmugge, T.↗
NASA NTRS1985

Eccentricity and misalignment effects on the performance of high-pressure annular seals

Annular pressure seals act as powerful hydrostatic bearings and influence the dynamic characteristics of rotating machinery. This work, using the existing concentric seal theories, provides a simple approximate method for calculation of both seal leakage and the dynamic coefficients for short seals with large eccentricity and/or misalignment of the shaft. Rotation and surface roughness effects are included for leakage and dynamic force calculation. The leakage calculations for both laminar and turbulent flow are compared with experimental results. The dynamic coefficients are compared with analytical results. Excellent agreement between the present work and published results have been observed up to the eccentricitiy ratio of 0.8.

Chen, W. C.↗
NASA NTRS1994

Estimation of grain sizes and mixing ratios of fine powder mixtures of common geologic minerals

Two different approaches for modeling reflectance spectra of intimate mixtures, Hapke's model and the isograin model, are used to estimate grain sizes and mixing ratios of powder mixtures of three geologic minerals: olivine, orthopyroxene, and plagioclase. In Hapke's model, scattering and extinction effiencies are mixed separately, and both models employ semiempirical refractive index spectra for component minerals. Mixing ratios of mixtures of grain size 45-75 micrometers are well estimated by both models assuming a common grain size of 60 micrometers and optimizing the constants for the single-particle scattering. For each model, effective grain size ratios for mineral constituents in mixtures of grain size less than 25 micrometers, are derived successfully that allows mineral abundances to be accurately predicted within approximately 4 wt percent. On the other hand, neither model can accurately predict mineral reflectance spectra for its smaller grain sizes less than 25 and 25-45 micrometers using an absorption coefficient spectrum derived from a larger grain size (45-75 micrometers). The errors in both models are significantly reduced if surface roughness effects of the smaller grain-size fractions are modeled.

Hiroi, Takahiro↗
NASA NTRS1984

Effect of substrate chemical pretreatment on the tribological properties of graphite films

Rubbed films of natural flake Madagascar graphite were applied to ASTM A-355(D) steel with chemical surface pretreatments of zinc phosphate, gas nitride, salt nitride, sulfo-nitride, and with mechanical pretreatment (sandblasting). SAE 1045 steel pins were slid against these films using a pin-on-disk tribometer. The results indicate that two different lubricating mechanisms can occur. In the chemical surface pretreatment, the graphite can mix together to form a surface layer of the two constituents and this plasticity flowing layer provides the lubrication. The longest endurance lives and the lowest pin wear rates were obtained with this mechanism. In the other, surface topography appeared to control the mechanism. A rough surface was necessary to serve as a reservoir to supply the graphite to the flat metallic plateaus where it was sheared in very thin films between the plateaus and the sliding pin surface. For this mechanism, chemical pretreatment seemed to do little more than serve as a means for roughening the surface. Mean friction was not significantly influenced by chemical pretreatment, but surface roughness effects were observed.

Fusaro, R. L.↗