Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STIRRING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Correlation between microstructure and residual stress formation in friction stir welded armor steels characterized by neutron diffraction

Friction stir welding (FSW) is a solid-state joining process that minimizes the heat-affected zone (HAZ) compared with fusion-based arc welding, making it well suited for joining martensitic armor steels where hardness and ballistic resistance are critical. This study investigates residual stress formation in three defect-free FSW butt-joint configurations relevant to armored-vehicle fabrication: similar rolled homogeneous armor (RHA–RHA, Case 1), similar high-hardness armor (HHA–HHA, Case 2), and dissimilar HHA–RHA (Case 3) joints produced under temperature-controlled conditions (770 °C). Neutron diffraction was employed to quantify the magnitude and spatial distribution of residual stresses in the longitudinal, transverse, and normal directions and to correlate them with weld microstructure and hardness. Tensile residual stresses were concentrated in the softened HAZ, reaching approximately 300 MPa for Case 2 and 400 MPa for Case 1 (≈50–70 % of the base-metal yield strength; ∼581 MPa for RHA and ∼566 MPa for HHA), while compressive residual stresses dominated the stir zone. The spatial extent of tensile stresses scaled with the width of the softened HAZ, which was largest in the dissimilar HHA–RHA joint and smallest in the HHA–HHA joint. Full-width-at-half-maximum (FWHM) analysis revealed low microstrain in overtempered HAZ regions and high microstrain in the stir zone associated with severe plastic deformation and fresh martensite formation. This work demonstrates that residual stress evolution in FSW of martensitic armor steels is governed not primarily by peak temperature or thermal contraction, as inferred from fusion-welding analogies, but by the competition between transformation-induced volumetric expansion and tempering-induced stress relaxation. The relative dominance of these mechanisms is shown to depend on alloy hardenability and local thermal history, leading to more extensive HAZ softening and broader tensile stress regions in the lower-hardenability RHA steel. These findings establish a transferable mechanistic framework for optimizing solid-state joining strategies in high-strength steels and other transformation-hardening alloys beyond armor applications.

Friction stir welding↗
DOE OSTI2015

Effect of friction stir welding and post-weld heat treatment on a nanostructured ferritic alloy

Nanostructured ferritic alloys (NFAs) are new generation materials for use in high temperature energy systems, such as nuclear fission or fusion reactors. However, joining these materials is a concern, as their unique microstructure is destroyed by traditional liquid-state welding methods. The microstructural evolution of a friction stir welded 14YWT NFA was investigated by atom probe tomography, before and after a post-weld heat treatment (PWHT) at 1123K. The particle size, number density, elemental composition, and morphology of the titanium-yttrium-oxygenenriched nanoclusters (NCs) in the stir and thermally-affected zones were studied and compared with the base metal. No statistical difference in the size of the NCs was observed in any of these conditions. After the PWHT, increases in the number density and the oxygen enrichment in the NCs were observed. Therefore, these new results provide additional supporting evidence that friction stir welding appears to be a viable joining technique for NFAs, as the microstructural parameters of the NCs are not strongly affected, in contrast to traditional welding techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Room temperature corrosion behaviour of plastically deformed AISI 304 stainless steel by friction stir welding in neutral and acidified chloride solutions

Severe plastic deformation of 304L stainless steel plate was carried out by friction stirring under an isothermal tool temperature at 825°C. The friction stirred zone showed extensive grain refinement, high fraction of low angle grain boundaries due to dislocation rearrangement, Σ3 and Σ9 special grain boundaries and discrete Fe–Cr–Mn-rich particles. Electrochemical polarisation measurements were done on the base metal (BM) and friction stir welded (FSW) specimens in the neutral and acidified 3.5% NaCl solutions. The BM showed marginally better pitting resistance in the neutral chloride solution than the FSW because of a larger fraction of special grain boundaries, and larger grain size. Whereas in acidified 3.5% NaCl solution, the FSW showed better corrosion resistance than the BM. Furthermore, the surface film of the FSW had a lower impedance and a lower defect concentration than the BM indicating higher diffusivity of point defects in the FSW.

36 MATERIALS SCIENCE↗
DOE OSTI2012

THE SHAPES OF MILKY WAY SATELLITES: LOOKING FOR SIGNATURES OF TIDAL STIRRING

We study the shapes of Milky Way satellites in the context of the tidal stirring scenario for the formation of dwarf spheroidal galaxies. The standard procedures used to measure shapes involve smoothing and binning of data and thus may not be sufficient to detect structural properties such as bars, which are usually subtle in low surface brightness systems. Taking advantage of the fact that in nearby dwarfs photometry of individual stars is available, we introduce discrete measures of shape based on the two-dimensional inertia tensor and the Fourier bar mode. We apply these measures of shape first to a variety of simulated dwarf galaxies formed via tidal stirring of disks embedded in dark matter halos and orbiting the Milky Way. In addition to strong mass loss and randomization of stellar orbits, the disks undergo morphological transformation that typically involves the formation of a triaxial bar after the first pericenter passage. These tidally induced bars persist for a few Gyr before being shortened toward a more spherical shape if the tidal force is strong enough. We test this prediction by measuring in a similar way the shape of nearby dwarf galaxies, satellites of the Milky Way. We detect inner bars in Ursa Minor, Sagittarius, Large Magellanic Cloud, and possibly Carina. In addition, 6 out of 11 dwarfs that we studied show elongated stellar distributions in the outer parts that may signify transition to tidal tails. We thus find the shapes of Milky Way satellites to be consistent with the predictions of the tidal stirring model.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2015

Stability of Y–Ti–O precipitates in friction stir welded nanostructured ferritic alloys

Nanostructured ferritic alloys, which have complex microstructures which consist of ultrafine ferritic grains with a dispersion of stable oxide particles and nanoclusters, are promising materials for fuel cladding and structural applications in the next generation nuclear reactor. This paper evaluates microstructure of friction stir welded nanostructured ferritic alloys using electron microscopy and atom probe tomography techniques. Atom probe tomography results revealed that nanoclusters are coarsened and inhomogeneously distributed in the stir zone and thermomechanically affected zone. Three hypotheses on coarsening of nanoclusters are presented. Finally, the hardness difference in different regions of friction stir weld has been explained.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Additive Friction Stir Deposition of a Tantalum–Tungsten Refractory Alloy

Additive friction stir deposition (AFSD) is a solid-state metal additive manufacturing technique, which utilizes frictional heating and plastic deformation to create large deposits and parts. Much like its cousin processes, friction stir welding and friction stir processing, AFSD has seen the most compatibility and use with lower-temperature metals, such as aluminum; however, there is growing interest in higher-temperature materials, such as titanium and steel alloys. In this work, we explore the deposition of an ultrahigh-temperature refractory material, specifically, a tantalum–tungsten (TaW) alloy. The solid-state nature of AFSD means refractory process temperatures are significantly lower than those for melt-based additive manufacturing techniques; however, they still pose difficult challenges, especially in regards to AFSD tooling. In this study, we perform initial deposition trials of TaW using twin-rod-style AFSD with a high-temperature tungsten–rhenium-based tool. Many challenges arise because of the high temperatures of the process and high mechanical demand on AFSD machine hardware to process the strong refractory alloy. Despite these challenges, successful deposits of the material were produced and characterized. Mechanical testing of the deposited material shows improved yield strength over that of the annealed reference material, and this strengthening is mostly attributed to the refined recrystallized microstructure typical of AFSD. These findings highlight the opportunities and challenges associated with ultrahigh-temperature AFSD, as well as provide some of the first published insights into twin-rod-style AFSD process behaviors.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Defect‐Free Sound Insulator Using Single Metal‐Based Friction Stir Process Array

Metals are excellent conductors for phonon transportation such as vibration, sound, and heat. Generally, metal sound insulators require multimaterial structure or defects and unimetal sound insulators are challenging. Therefore, a design of a defect-free sound insulator made by single alloys with multiple friction stir processes (FSPs) is proposed. Periodic friction stir processing can induce superlattice-like local mechanical properties’ modifications. By experimental acoustic characterization, it is observed that FSP can introduce clear acoustic–elastic property contrast on an aluminum plate by the presence of stir zone and heat-affected zones. In numerical simulations, the signature FSP-induced property profile is periodically and parallelly arranged on a long aluminum plate. The transmission gap frequencies are present on the frequency spectrum with the sound propagation direction perpendicular to the FSP paths. Disorder offsets on FSP periodicity are further introduced. Anderson localization is found on a resonance frequency, which provides −11 dB sound reduction by an exponential decay. Due to the finite design length, the slight disorder can also enhance sound insulation in the periodic transmission gap frequency. In conclusion, with analysis and comparison with different configurations, the best performance in the models can achieve −30 dB sound insulation in the 350 mm-long aluminum alloy plate with 14 parallel FSPs.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Physics-based process model approach for detecting discontinuity during friction stir welding

The goal of this work is to develop a method for detecting the creation of discontinuities during friction stir welding. This in situ weld monitoring method could significantly reduce the need for post-process inspection. A process force model and a discontinuity force model were created based on the state-of-the-art understanding of flow around an friction stir welding (FSW) tool. These models are used to predict the FSW forces and size of discontinuities formed in the weld. Friction stir welds with discontinuities and welds without discontinuities were created, and the differences in force dynamics were observed. In this paper, discontinuities were generated by reducing the tool rotation frequency and increasing the tool traverse speed in order to create "cold" welds. Experimental force data for welds with discontinuities and welds without discontinuities compared favorably with the predicted forces. The model currently overpredicts the discontinuity size.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Stress interference in multilayer additive friction stir deposition of AA6061 aluminum

Due to the multilayer deposition nature of metal additive manufacturing processes, each layer being printed experiences the state of thermokinetic and thermomechanical stress that in turn interfere with the state of thermokinetics and thermomechanical stress of subsequently deposited layers. Especially, this multilayer interference significantly affects the resultant properties of the component fabricated using solid-state additive friction stir deposition due to evolution of asymmetric state of planar stress. Due to the lack of comprehensive and suitable in situ diagnosis technique, the complex interference of inter- and multi-layer stresses during additive friction stir deposition was studied in an integrated approach of numerical simulation of fluidic state and experimental probing of stress influenced ultrasonic elastography. The uni-directional and bi-directional layer deposition configurations adopted during additive friction stir deposition result in the generation of constructive and destructive interference of the interlayer stress and hence, asymmetric and symmetric dynamic elasticity distribution respectively within the subsequent layers. With subsequent deposition of additional layers, the odd and even numbers of deposited layers generate asymmetric and nearly symmetric dynamic elasticity distributions.

Yang, Teng↗
DOE OSTI2018

Friction Stir Welding of Dissimilar Al/Al and Al/Non-Al Alloys: A Review

Friction stir welding is a solid-state welding technique that has many advantages over traditional fusion welding, and has been widely adopted in the aerospace and automotive industries. This article reviews research developments in friction stir welding of dissimilar alloys systems, including combinations of aluminum alloys with Mg alloys, Cu, and steel. Microstructural evolution, hardness, tensile and fatigue properties, residual stresses, and corrosion behavior of dissimilar welds will be reported. The effects of processing parameters such as tool rotation and traverse speeds, tool position, material position, and tool geometry on the weld quality are also presented. Discussions on future research directions in friction stir welding will also be provided in the context of existing literature and future high-integrity applications.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Heat Exposure on the Fatigue Properties of AA7050 Friction Stir Welds

This work examines the effect of heat exposure on the subsequent monotonic and fatigue properties of friction stir-welded AA7050. Mechanical characterization tests were conducted on friction stir-welded specimens as-welded (AW) and specimens heated to 315 °C in air for 20 min. Monotonic testing revealed high joint efficiencies of 98% (UTS) in the AW specimens and 60% in the heat-damaged (HD) specimens. Experimental results of strain-controlled fatigue testing revealed shorter fatigue lives for the HD coupons by nearly a factor of four, except for the highest strain amplitude tested. Postmortem fractography analysis found similar crack initiation or propagation behavior between the AW and HD specimens; however, the failure locations for the AW were predominantly in the heat-affected zone, while the HD specimens also failed in the stir zone. Microhardness measurements revealed a relatively uniform strength profile in the HD group, accounting for the variety of failure locations observed. The differences in both monotonic and cyclic properties observed between the AW and HD specimens support the conclusion that the heat damage (315 °C at 20 min) acts as an over-aging and a quasi-annealing treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Interfacial Microstructure and Mechanical Properties of Friction Stir Welded Joints of Commercially Pure Aluminum and 304 Stainless Steel

In the present investigation, friction stir welding of commercially pure aluminum and 304 stainless steel was carried out at varying tool rotational speeds from 200 to 1000 rpm in steps of 200 rpm using 60 mm/min traverse speed at 2 (degree) tool tilt angle. Microstructural characterization of the interfacial zone was carried out using optical microscope and scanning electron microscope. Energy-dispersive spectroscopy indicated the presence of FeAl{sub 3} intermetallic phase. Thickness of the intermetallic layer increased with the increase in tool rotational speed. X-ray diffraction studies indicated the formation of intermetallic phases like FeAl{sub 2}, Fe{sub 4}Al{sub 13}, Fe{sub 2}Al{sub 5}, and FeAl{sub 3}. A maximum tensile strength of ~ 90% that of aluminum along with ~ 4.5% elongation was achieved with the welded sample at tool rotational speed of 400 rpm. The stir zone showed higher hardness as compared to base metals, heat affected zone, and thermo-mechanically affected zone due to the presence of intermetallics. The maximum hardness value at the stir zone was achieved at 1000 rpm tool rotational speed.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Rotation Speed on the Microstructure and Mechanical Properties of Friction-Stir-Welded CuSn6 Tin Bronze

Four-mm-thick CuSn6 tin bronze plates were friction stir welded at a constant tool traverse speed of 100 mm min{sup −1}. Favorable joints could be obtained with rotation speeds ranging from 600 to 1000 rev min{sup −1}, and groove was found on the surface of the joint under 400 rev min{sup −1}. The microstructure of the weld nugget zone was characterized by equiaxed recrystallized grains with heterogeneity along the thickness direction. Moreover, the grain size of the thermo-mechanically affected zone and stir zone increased with the increase in rotation speed. Hardness of the stir zone was higher than that of other zones due to microstructural refinement. There was little change in tensile properties of the defect-free welded joints. During tensile test, all of the defect-free joints were fractured at heat-affected zone with typical plastic fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Influence of Welding Speed on Zigzag Line Feature and Tensile Property of a Friction-Stir-Welded Al-Zn-Mg Aluminum Alloy

The zigzag line has significant and complicated effects on the mechanical properties of friction-stir-welded aluminum alloys. The zigzag line feature and its affecting characteristic on joint property are largely related to welding speed. In this paper, an Al-Zn-Mg aluminum alloy was butt friction-stir-welded, and the effects of welding speed on zigzag line feature and joint property were studied in detail in order to reveal the intrinsic correlations between the critical process parameter and the weld quality and, consequently, to provide guidance for the process optimization. The results indicate that at high welding speed of 300 mm/min, the loose and dilute distribution of the oxide layer fragments induces the relatively ambiguous zigzag line feature; the joint does not fail through the zigzag line during tensile test and shows superior tensile properties. With decreasing welding speed to 175 and 50 mm/min, the zigzag line feature is not weakened by the severer tool stirring action, as widely reported by previous studies, but is strengthened gradually due to the enhancement of the collective flow and more concentrated redistribution of broken oxide particles, leading to joint failure at zigzag lines and the degradation of tensile properties of joints.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Tool Pin Eccentricity on the Microstructure and Mechanical Properties of Friction Stir Processed Al-6061 Alloy

Three different stir tools with the pin eccentricity of 0, 0.4 and 0.8 mm were applied to the friction stir processing (FSP) of Al-6061 alloy. Results show that the pin-affected zone (PAZ) enlarges and the grain size in the stir zone (SZ) decreases as the pin eccentricity increases. Moreover, the low peak FSP temperature induced by the pin eccentricity gives rise to the coarsening of strengthening precipitates in the SZ. Compared with the pin-eccentric FSP samples, the SZ produced without pin eccentricity exhibits the highest hardness and yield strength due to the high amount of fine precipitates. However, the application of pin eccentricity elevates the overall tensile properties of FSP samples through changing the failure location from heat-affected zone (HAZ) to SZ.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructural Characteristics and Mechanical Properties of Friction-Stir-Welded CuSn6 Tin Bronze

Tin bronze is widely applied in various industries for its excellent wear and corrosion resistance. Friction stir welding is a solid-state welding process, which generates less heat and avoids the melting-related defects. CuSn6 tin bronze plates of 4 mm in thickness were friction-stir-welded at welding speeds ranging from 50 to 150 mm/min under a constant rotation speed. The microstructural and mechanical properties of joints were investigated. The microstructure of the stir zone consists of refined equiaxed grains. The grain size decreased from top to bottom of the welds. The mean grain size is increased with increasing welding speed. The largest strength and elongation of welded joints were both obtained at the welding speed of 100 mm/min. During tensile test, all of the joints were fractured at the heat affected zone of retreating side with typical plastic fracture feature, since the grains were coarsened by welding heat.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure and Mechanical Behavior of Friction Stir-Welded Sc-Modified Al-Zn-Mg Alloys Made Using Different Base Metal Tempers

The microstructure and property of friction stir weld joints of a Sc-modified Al-Zn-Mg alloy developed using base metal in hot-rolled (HR) and T6 temper were studied and compared in this work. The results showed that the microstructure and property exhibited significant difference between the two friction stir weld joints. The weld efficiency of the FSW joint developed using base metal in HR condition is over 90%, while that of the FSW joint developed using base metal in T6 condition is only 70%. The hardness of the weld nugget of HR joint is obviously higher than that of the weld nugget of T6 joint, due to the different changes in the original precipitates during the friction stir welding process. The strengthening mechanism in different zones of the two FSW joints was discussed to examine the microstructure–properties relationship, and the main difference of the strengthening mechanism between the two FSW joints was revealed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Joining AA7099 to Ni-Cr-Mo Steel Using Single Pass Friction Stir Dovetailing and AA6061 Butter Layer

A novel single pass friction stir dovetailing (FSD) was developed to join thick plate AA7099 to Ni-Cr-Mo steel in a lap configuration through the use of an AA6061 butter layer. The butter layer approach can be shown to significantly reduce interfacial failures by inhibiting the formation of brittle Fe–Al intermetallic compounds (IMCs) which are typically formed during conventional friction stir welding (FSW) of AA7099 directly to steel. This study evaluates the strength and microstructural evolution of the aluminum/steel joint interface between single pass FSD of AA7099/AA6061(butter)/steel fabricated using three different FSD tool configurations. The butter layer was achieved by placement of a free-floating strip of AA6061 within the dovetail groove that was pre-machined in the steel substrate. Friction stir welding was then used to simultaneously join the thick plate AA7099, the AA6061 strip and the AA7099 in a single weld pass. To optimize the joining process, three different pin geometries (full thread, half smooth/half thread, no thread) were evaluated; it was demonstrated that the half smooth/half thread tool produced the strongest weld joint due to the absence of a Zn rich layer at the Al/steel interface. The efficacy of this unique processing technique was tested using lap shear tensile testing as well as high resolution transmission electron microscopy (TEM). A discussion of the new FSD technique, joint configurations, and process parameters are provided along with joint microstructural analyses and mechanical performance.

Olszta, Matthew J.↗