SEARCH · Engineering Papers

Results for “STABILITY AUGMENTATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Stability and control of maneuvering high-performance aircraft

The stability and control of a high-performance aircraft was analyzed, and a design methodology for a departure prevention stability augmentation system (DPSAS) was developed. A general linear aircraft model was derived which includes maneuvering flight effects and trim calculation procedures for investigating highly dynamic trajectories. The stability and control analysis systematically explored the effects of flight condition and angular motion, as well as the stability of typical air combat trajectories. The effects of configuration variation also were examined.

Stengel, R. F.↗

NASA NTRS1990

Lateral-directional stability and control characteristics of the Quiet Short-Haul Research Aircraft (QSRA)

The results are presented of flight experiments to determine the lateral-directional stability and control characteristics of the Quiet Short-Haul Research Aircraft (QSRA), an experimental aircraft designed to furnish information on various aerodynamic characteristics of a transport type of airplane that makes use of the upper-surface blown (USB) flap technology to achieve short takeoff and landing (STOL) performance. The flight program designed to acquire the data consisted of maneuvers produced by rudder and control-wheel inputs with the airplane in several configurations that had been proposed for landing approach and takeoff operation. The normal stability augmentation system was not engaged during these maneuvers. Time-history records from the maneuvers were analyzed with a parameter estimation procedure to extract lateral-directional stability and control derivatives. For one aircraft configuration in which the USB flaps were deflected 50 deg, several maneuvers were performed to determine the effects of varying the average angle of attack, varying the thrust coefficient, and setting the airplane's upper surface spoilers at a 13 deg symmetrical bias angle . The effects on the lateral characteristics of deflecting the spoilers were rather small and generally favorable. The data indicate that for one test, conducted at low thrust (a thrust coefficient of 0.38), compared with results from tests at thrust coefficients of 0.77 and larger, there was a significant decrease in the lateral control effectiveness, in the yaw damping and in the directional derivative. The directional derivative was also decreased (by about 30 percent) when the average angle of attack of the test was increased from 3 to 16 deg.

Stephenson, Jack D.↗

NASA NTRS1974

A predictive pilot model for STOL aircraft landing

An optimal control approach has been used to model pilot performance during STOL flare and landing. The model is used to predict pilot landing performance for three STOL configurations, each having a different level of automatic control augmentation. Model predictions are compared with flight simulator data. It is concluded that the model can be effective design tool for studying analytically the effects of display modifications, different stability augmentation systems, and proposed changes in the landing area geometry.

Kleinman, D. L.↗

NASA NTRS1985

Development of a sensitivity analysis technique for multiloop flight control systems

This report presents the development and application of a sensitivity analysis technique for multiloop flight control systems. This analysis yields very useful information on the sensitivity of the relative-stability criteria of the control system, with variations or uncertainties in the system and controller elements. The sensitivity analysis technique developed is based on the computation of the singular values and singular-value gradients of a feedback-control system. The method is applicable to single-input/single-output as well as multiloop continuous-control systems. Application to sampled-data systems is also explored. The sensitivity analysis technique was applied to a continuous yaw/roll damper stability augmentation system of a typical business jet, and the results show that the analysis is very useful in determining the system elements which have the largest effect on the relative stability of the closed-loop system. As a secondary product of the research reported here, the relative stability criteria based on the concept of singular values were explored.

Vaillard, A. H.↗

NASA NTRS1988

A Mathematical Formulation of the SCOLE Control Problem. Part 2: Optimal Compensator Design

The study initiated in Part 1 of this report is concluded and optimal feedback control (compensator) design for stability augmentation is considered, following the mathematical formulation developed in Part 1. Co-located (rate) sensors and (force and moment) actuators are assumed, and allowing for both sensor and actuator noise, stabilization is formulated as a stochastic regulator problem. Specializing the general theory developed by the author, a complete, closed form solution (believed to be new with this report) is obtained, taking advantage of the fact that the inherent structural damping is light. In particular, it is possible to solve in closed form the associated infinite-dimensional steady-state Riccati equations. The SCOLE model involves associated partial differential equations in a single space variable, but the compensator design theory developed is far more general since it is given in the abstract wave equation formulation. The results thus hold for any multibody system so long as the basic model is linear.

Balakrishnan, A. V.↗

NASA NTRS1981

Effects of displacement and rate saturation on the control of statically unstable aircraft

Methodologies are presented for the analysis and design of stability augmentation control laws for aircraft in which 'hard' displacement and rate limiting are significant. Candidate control laws are derived using the linear-quadratic (LQ) regulator. Analytical and computational estimates of the stability limits imposed by control saturation are presented using state trajectories with control limiting, as well as describing functions and eigenvalue computation. Analysis also includes an investigation of the interaction of the state-space saturation and stability boundaries for various choices of LQ weighting matrices. For minimum-energy control, the saturation and stability boundaries are shown to be parallel. In this case, there is a direct relation between the solution to the matrix Riccati equation and the aircraft's open-loop dynamics.

Hanson, G. D.↗

NASA NTRS2004

A New Approach to Attitude Stability and Control for Low Airspeed Vehicles

This paper describes an approach for controlling the attitude of statically unstable thrust-levitated vehicles in hover or slow translation. The large thrust vector that characterizes such vehicles can be modulated to provide control forces and moments to the airframe, but such modulation is accompanied by significant unsteady flow effects. These effects are difficult to model, and can compromise the practical value of thrust vectoring in closed-loop attitude stability, even if the thrust vectoring machinery has sufficient bandwidth for stabilization. The stabilization approach described in this paper is based on using internal angular momentum transfer devices for stability, augmented by thrust vectoring for trim and other "outer loop" control functions. The three main components of this approach are: (1) a z-body axis angular momentum bias enhances static attitude stability, reducing the amount of control activity needed for stabilization, (2) optionally, gimbaled reaction wheels provide high-bandwidth control torques for additional stabilization, or agility, and (3) the resulting strongly coupled system dynamics are controlled by a multivariable controller. A flight test vehicle is described, and nonlinear simulation results are provided that demonstrate the efficiency of the approach.

Lim, K. B.↗

NASA NTRS1974

Determination of propulsion-system-induced forces and moments of a Mach 3 cruise aircraft

During the joint NASA/USAF flight research program with the YF-12 airplane, the Dutch roll damping was found to be much less during automatic inlet operation than during fixed inlet operation at Mach numbers greater than 2.5 and with the yaw stability augmentation system off. It was concluded that the significant reduction in Dutch roll damping was due to the forces and moments induced by the variable-geometry features of the inlet. Two stability-derivative extraction techniques were applied to the flight data; the recently developed Newton-Raphson technique and the time vector method. These techniques made it possible to determine the forces and moments generated by spike and bypass door movement.

Gilyard, G. B.↗

NASA NTRS2001

Rotor Design Options for Improving V-22 Whirl-Mode Stability

With current tilt-rotor technology, very stiff, thick wings of limited aspect ratio are essential to meet aeroelastic stability requirements, which severely limits cruise efficiency and maximum speed. Larger and more efficient tiltrotors; will need longer and lighter wings, for which whirl-mode flutter is a serious design issue. Numerous approaches to improving the whirl-mode airspeed boundary have been investigated, typically focusing on wing design, active stability augmentation, and variable geometry rotors. The research to be reported applies the much simpler approaches of sweeping the outboard blade sections and extending balance weights at the tip. Improving proprotor whirl-mode stability margins is an ongoing research activity at NASA Ames Research Center. Previous efforts focussed on the XV-15 rotor. This is the first application of these design principles to a full V-22 rotor model in CAMRAD II (a previous publication presented results for a preliminary analytical model). The analysis to be discussed in the proposed paper includes a dual load-path blade model, a compressible-flow aerodynamic model, a representation of swashplate/rotor modal coupling, and other new features. The paper will include discussions of the mechanisms by which blade sweep and tip-mass offsets improve whirl-flutter margins. The V-22 was modeled with CAMRAD II; the rotor model is shown. It is also shows an example swept blade derived from the V-22 rotor system. For this rotor, the primary significance of sweep is the improved whirl-flutter boundary, not the reduced Mach-number effects. An offset tip mass is also shown.

Acree, C. W., Jr.↗

NASA NTRS2011

A Piloted Evaluation of Damage Accommodating Flight Control Using a Remotely Piloted Vehicle

Toward the goal of reducing the fatal accident rate of large transport airplanes due to loss of control, the NASA Aviation Safety Program has conducted research into flight control technologies that can provide resilient control of airplanes under adverse flight conditions, including damage and failure. As part of the safety program s Integrated Resilient Aircraft Control Project, the NASA Airborne Subscale Transport Aircraft Research system was designed to address the challenges associated with the safe and efficient subscale flight testing of research control laws under adverse flight conditions. This paper presents the results of a series of pilot evaluations of several flight control algorithms used during an offset-to-landing task conducted at altitude. The purpose of this investigation was to assess the ability of various flight control technologies to prevent loss of control as stability and control characteristics were degraded. During the course of 8 research flights, data were recorded while one task was repeatedly executed by a single evaluation pilot. Two generic failures, which degraded stability and control characteristics, were simulated inflight for each of the 9 different flight control laws that were tested. The flight control laws included three different adaptive control methodologies, several linear multivariable designs, a linear robust design, a linear stability augmentation system, and a direct open-loop control mode. Based on pilot Cooper-Harper Ratings obtained for this test, the adaptive flight control laws provided the greatest overall benefit for the stability and control degradation scenarios that were considered. Also, all controllers tested provided a significant improvement in handling qualities over the direct open-loop control mode.

Cunningham, Kevin↗

NASA NTRS1978

Pilot-optimal augmentation synthesis

An augmentation synthesis method usable in the absence of quantitative handling qualities specifications, and yet explicitly including design objectives based on pilot-rating concepts, is presented. The algorithm involves the unique approach of simultaneously solving for the stability augmentation system (SAS) gains, pilot equalization and pilot rating prediction via optimal control techniques. Simultaneous solution is required in this case since the pilot model (gains, etc.) depends upon the augmented plant dynamics, and the augmentation is obviously not a priori known. Another special feature is the use of the pilot's objective function (from which the pilot model evolves) to design the SAS.

Schmidt, D. K.↗

NASA NTRS1979

Control system techniques for improved departure/spin resistance for fighter aircraft

Some fundamental information on control system effects on controllability of highly-maneuverable aircraft at high angles of attack and techniques for enhancing fighter aircraft departure/spin resistance using control system design is summarized. The discussion includes: (a) a brief review of pertinent high angle-of-attack phenomena including aerodynamics, inertia coupling, and kinematic coupling; (b) effects of conventional stability augmentation systems at high-alpha; (c) high-alpha control system concepts designed to enhance departure/spin resistance; and (d) the outlook for applications of these concepts to future fighters, particularly those designs which incorporate relaxed static stability.

Nguyen, L. T.↗

NASA NTRS1976

Study of an aircraft decoupled longitudinal control system for approach and landing

A series of ground-based and in-flight simulation studies of the application of steady-state decoupled longitudinal controls to a short take-off and landing (STOL) transport have been made. The externally blown flap STOL was selected for study because it was considered to be a worst-case situation from the control viewpoint. The decoupled longitudinal control system used constant prefilter and feedback gains to provide independent control of flight-path angle, pitch angle, and forward velocity during landing approach. The decoupled controls were compared to a more conventional stability augmentation system. The pilots were enthusiastic about the decoupled controls; the pilot workload was reduced and the landing performance significantly improved. The benefit of the decoupled controls was more dramatic during in-flight simulation using a variable stability airplane than was the case with either fixed- or moving-base, ground-based simulators.

Miller, G. K., Jr.↗

NASA NTRS2000

Exploratory Studies in Generalized Predictive Control for Active Aeroelastic Control of Tiltrotor Aircraft

The Aeroelasticity Branch at NASA Langley Research Center has a long and substantive history of tiltrotor aeroelastic research. That research has included a broad range of experimental investigations in the Langley Transonic Dynamics Tunnel (TDT) using a variety of scale models and the development of essential analyses. Since 1994, the tiltrotor research program has been using a 1/5-scale, semispan aeroelastic model of the V-22 designed and built by Bell Helicopter Textron Inc. (BHTI) in 1981. That model has been refurbished to form a tiltrotor research testbed called the Wing and Rotor Aeroelastic Test System (WRATS) for use in the TDT. In collaboration with BHTI, studies under the current tiltrotor research program are focused on aeroelastic technology areas having the potential for enhancing the commercial and military viability of tiltrotor aircraft. Among the areas being addressed, considerable emphasis is being directed to the evaluation of modern adaptive multi-input multi- output (MIMO) control techniques for active stability augmentation and vibration control of tiltrotor aircraft. As part of this investigation, a predictive control technique known as Generalized Predictive Control (GPC) is being studied to assess its potential for actively controlling the swashplate of tiltrotor aircraft to enhance aeroelastic stability in both helicopter and airplane modes of flight. This paper summarizes the exploratory numerical and experimental studies that were conducted as part of that investigation.

Kvaternik, Raymond G.↗

NASA NTRS1980

Control-system techniques for improved departure/spin resistance for fighter aircraft

This paper summarizes some fundamental information on control-system effects on controllability of highly maneuverable aircraft at high angles of attack and techniques for enhancing fighter aircraft departure/spin resistance using control-system design. The discussion includes (1) a brief review of pertinent high-angle-of-attack phenomena including aerodynamics, inertia coupling, and kinematic coupling, (2) effects of conventional stability augmentation systems at high angle of attack, (3) high-angle-of-attack control-system concepts designed to enhance departure/spin resistance, and (4) the outlook for applications of these concepts to future fighters, particularly those designs which incorporate relaxed static stability.

High angle of attack↗

NASA NTRS1983

Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transport project-longitudinal handling qualities study of a relaxed-stability airplane

The results of a piloted simulation of longitudinal handling qualities of an airplane with relaxed static stability are described. This task was performed under the Integrated Application of Active Controls (IAAC) Technology Project within the NASA Energy Efficient Transport Program. A representative medium range transport airplane, the Boeing Model 757, was simulated. Evaluations were made of the unaugmented airplane and of the airplane with an Essential Pitch Augmented Stability (PAS) System and with a Primary PAS System at various center of gravity (cg) conditions. Level 2 pilot ratings were attained with cg locations aft to about 57% mean aerodynamic chord (MAC) or 6% aft of the neutral point for unaugmented landing approach. For Mach = 0.80, unaugmented cruise Level 2 ratings were attained to 47% MAC or 5% forward of the maneuver point. The augmented airplane model provided handling qualities close to or within the Level 1 boundary at all cg locations for both Essential and Primary PAS. Analyses of the test conditions when compared with existing handling qualities criteria based on classical unaugmented airplane characteristics agreed well with the pilot ratings. The unaugmented results are comparable to those reported by both the Douglas Aircraft Company and Lockheed California Company from simulation investigations of transport configurations with roughly similar dimensional and mass characteristics.

Source record↗

NASA NTRS1976

Stability and control of maneuvering high-performance aircraft

Stability and control characteristics of a high-performance aircraft have been examined over a wide range of maneuvering flight conditions, in order to identify general rules for the design of departure-preventing control systems. This has been accomplished using fully coupled linear dynamic models which account for nonzero mean values of aerodynamic angles and angular rates. Stability augmentation systems derived from optimal control theory are shown to maintain stable, well-damped aircraft dynamics over a wide range of maneuvering flight conditions. This design approach generates cross-feeds and control interconnects (as well as conventional feedback terms) for improved aircraft stability.

Stengel, R. F.↗

NASA NTRS1986

Decoupling control synthesis for an oblique-wing aircraft

Interest in oblique-wing aircraft has surfaced periodically since the 1940's. This concept offers some substantial aerodynamic performance advantages but also has significant aerodynamic and inertial cross-coupling between the aircraft longitudinal and lateral-directional axes. This paper presents a technique for synthesizing a decoupling controller while providing the desired stability augmentation. The proposed synthesis procedure uses the concept of a real model-following control system. Feedforward gains are selected on the assumption that perfect model-following conditions are satisfied. The feedback gains are obtained by using eigensystem assignment, and the aircraft is stabilized by using partial state feedback. The effectiveness of the control laws developed in achieving the desired decoupling is illustrated by application to linearized equations of motion of an oblique-wing aircraft for a given flight condition.

Alag, G. S.↗