Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SILICIDES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Design of Silicide-Strengthened Nb–Si–Cr–(Mo) alloys for additive manufacturing

Three high–intermetallic volume Nb–Si–Cr–(Mo) alloys were designed using CALPHAD modeling with the goal of identifying high–specific strength, oxidation-resistant alloys that can be additively manufactured using powder bed fusion. The silicides Nb 5 Si 3 and Nb 9 Si 2 Cr3 were targeted as the primary strengthening phases, and the addition of Cr promoted the NbCr 2 phase. These alloys were cast and surface-processed with electron beam welding at different speeds to simulate additive manufacturing, and the phases and microstructures of both cast and welded regions were characterized. The weld processing was found to produce fine-grained microstructures in each alloy with fine-scale intermetallics uniformly distributed among a body-centered cubic Nb matrix. Microstructural refinement and hardness were found to increase with weld velocity; one alloy reached its highest hardness of approximately 16 GPa before the brittleness at higher velocities became detrimental. One alloy was found to be qualitatively the least brittle while also attaining a hardness of 13 GPa and was therefore identified as a good candidate for additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2013

Effects of (Al,Ge) double doping on the thermoelectric properties of higher manganese silicides

Experiments and analysis have been carried out to investigate the effects of Al and (Al,Ge) doping on the microstructure and thermoelectric properties of polycrystalline higher manganese silicide (HMS) samples, which were prepared by solid-state reaction, ball milling, and followed by spark plasma sintering. It has been found that Al doping effectively increases the hole concentration, which leads to an increase in the electrical conductivity and power factor. By introducing the second dopant Ge into Al-doped HMS, the electrical conductivity is increased, and the Seebeck coefficient is decreased as a result of further increased hole concentration. The peak power factor is found to occur at a hole concentration between 1.8 × 10{sup 21} and 2.2 × 10{sup 21} cm{sup −3} measured at room temperature. The (Al,Ge)-doped HMS samples show lower power factors owing to their higher hole concentrations. The mobility of Mn(Al{sub 0.0035}Ge{sub y}Si{sub 0.9965-y}){sub 1.8} with y = 0.035 varies approximately as T{sup −3/2} above 200 K, suggesting acoustic phonon scattering is the dominant scattering mechanism. The thermal conductivity of HMS does not change appreciably by Al or (Al,Ge) doping. The maximum ZT of (Al,Ge)-doped HMS is 0.57 at 823 K, which is similar to the highest value found in the Al-doped HMS samples. The ZT values were reduced in the Mn(Al{sub 0.0035}Ge{sub y}Si{sub 0.9965-y}){sub 1.8} samples with high Ge concentration of y = 0.025 and 0.035, because of reduced power factor. In addition, a two-band model was employed to show that the hole contribution to the thermal conductivity dominates the bipolar and electron contributions for all samples from 300 to 823 K and accounts for about 12% of the total thermal conductivity at about 800 K.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Electrical properties of amorphous and epitaxial Si-rich silicide films composed of W-atom-encapsulated Si clusters

We investigated the electrical properties and derived the energy band structures of amorphous Si-rich W silicide (a-WSi{sub n}) films and approximately 1-nm-thick crystalline WSi{sub n} epitaxial films (e-WSi{sub n}) on Si (100) substrates with composition n = 8–10, both composed of Si{sub n} clusters each of which encapsulates a W atom (WSi{sub n} clusters). The effect of annealing in the temperature range of 300–500 °C was also investigated. The Hall measurements at room temperature revealed that a-WSi{sub n} is a nearly intrinsic semiconductor, whereas e-WSi{sub n} is an n-type semiconductor with electron mobility of ∼8 cm{sup 2}/V s and high sheet electron density of ∼7 × 10{sup 12 }cm{sup −2}. According to the temperature dependence of the electrical properties, a-WSi{sub n} has a mobility gap of ∼0.1 eV and mid gap states in the region of 10{sup 19 }cm{sup −3} eV{sup −1} in an optical gap of ∼0.6 eV with considerable band tail states; e-WSi{sub n} has a donor level of ∼0.1 eV with sheet density in the region of 10{sup 12 }cm{sup −2} in a band gap of ∼0.3 eV. These semiconducting band structures are primarily attributed to the open band-gap properties of the constituting WSi{sub n} cluster. In a-WSi{sub n}, the random network of the clusters generates the band tail states, and the formation of Si dangling bonds results in the generation of mid gap states; in e-WSi{sub n}, the original cluster structure is highly distorted to accommodate the Si lattice, resulting in the formation of intrinsic defects responsible for the donor level.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2016

Capping of rare earth silicide nanowires on Si(001)

The capping of Tb and Dy silicide nanowires grown on Si(001) was studied using scanning tunneling microscopy and cross-sectional high-resolution transmission electron microscopy. Several nanometers thick amorphous Si films deposited at room temperature allow an even capping, while the nanowires maintain their original structural properties. Subsequent recrystallization by thermal annealing leads to more compact nanowire structures and to troughs in the Si layer above the nanowires, which may even reach down to the nanowires in the case of thin Si films, as well as to V-shaped stacking faults forming along (111) lattice planes. This behavior is related to strain due to the lattice mismatch between the Si overlayer and the nanowires.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2016

On the structural and electronic properties of Ir-silicide nanowires on Si(001) surface

Iridium (Ir) modified Silicon (Si) (001) surface is studied with Scanning Tunneling Microscopy/Spectroscopy (STM/STS) and Density Functional Theory (DFT). A model for Ir-silicide nanowires based on STM images and ab-initio calculations is proposed. According to our model, the Ir adatom is on the top of the substrate dimer row and directly binds to the dimer atoms. I-V curves measured at 77 K shows that the nanowires are metallic. DFT calculations confirm strong metallic nature of the nanowires.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2016

Improvement of the thermal stability of nickel silicide using a ruthenium interlayer deposited via remote plasma atomic layer deposition

In this study, the effects of a thin Ru interlayer on the thermal and morphological stability of NiSi have been investigated. Ru and Ni thin films were deposited sequentially to form a Ni/Ru/Si bilayered structure, without breaking the vacuum, by remote plasma atomic layer deposition (RPALD) on a p-type Si wafer. After annealing at various temperatures, the thermal stabilities of the Ni/Ru/Si and Ni/Si structures were investigated by various analysis techniques. The results showed that the sheet resistance of the Ni/Ru/Si sample was consistently lower compared to the Ni/Si sample over the entire temperature range. Although both samples exhibited the formation of NiSi{sub 2} phases at an annealing temperature of 800 °C, as seen with glancing angle x-ray diffraction, the peaks of the Ni/Ru/Si sample were observed to have much weaker intensities than those obtained for the Ni/Si sample. Moreover, the NiSi film with a Ru interlayer exhibited a better interface and improved surface morphologies compared to the NiSi film without a Ru interlayer. These results show that the phase transformation of NiSi to NiSi{sub 2} was retarded and that the smooth NiSi/Si interface was retained due to the activation energy increment for NiSi{sub 2} nucleation that is caused by adding a Ru interlayer. Hence, it can be said that the Ru interlayer deposited by RPALD can be used to control the phase transformation and physical properties of nickel silicide phases.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Superconducting platinum silicide analyzed by x-ray photoelectron spectroscopy

Platinum silicide has garnered increased attention due to its potential applications as a superconductor within silicon technology. In this work, we characterize a superconducting PtSi film using x-ray photoelectron spectroscopy with an Al K α excitation source. Survey spectra, Pt 5s, Pt 4f, Pt 4d, Pt 4p, Pt 4s, Si 2p, Si 2s, O 1s core levels, and the valence band spectrum were measured. In conclusion, this collection of high-quality core level spectra of a superconducting PtSi film provide reference data for this material, which often has a minimal native silicon oxide layer and overlapping Si and Pt core level peaks.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

Diffusion Paths for Interstitial Impurities in Different Polymorphic Modifications of Niobium Silicide Nb{sub 5}Si{sub 3}

Structural models of the α, β, and γ modifications of Nb{sub 5}Si{sub 3} silicides, which are used as a reinforcing phase in composites obtained in situ based on the Nb‒Si system, have been constructed by computer simulation methods. A geometric analysis of unit cells is performed using the H-poisk program to estimate the voids existing in the structures. The results of measuring the number of voids and their sizes are reported. A conclusion about possible diffusion paths of interstitial boron, carbon, nitrogen and oxygen atoms is drawn based on the calculation results, and the solubility of these impurities in the structure of each Nb{sub 5}Si{sub 3} modification is estimated.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Analysis of optical and magnetooptical spectra of Fe{sub 5}Si{sub 3} and Fe{sub 3}Si magnetic silicides using spectral magnetoellipsometry

The optical, magnetooptical, and magnetic properties of polycrystalline (Fe{sub 5}Si{sub 3}/SiO{sub 2}/Si(100)) and epitaxial Fe{sub 3}Si/Si(111) films are investigated by spectral magnetoellipsometry. The dispersion of the complex refractive index of Fe{sub 5}Si{sub 3} is measured using multiangle spectral ellipsometry in the range of 250–1000 nm. The dispersion of complex Voigt magnetooptical parameters Q is determined for Fe{sub 5}Si{sub 3} and Fe{sub 3}Si in the range of 1.6–4.9 eV. The spectral dependence of magnetic circular dichroism for both silicides has revealed a series of resonance peaks. The energies of the detected peaks correspond to interband electron transitions for spin-polarized densities of electron states (DOS) calculated from first principles for bulk Fe{sub 5}Si{sub 3} and Fe{sub 3}Si crystals.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2018

Effect of Epitaxial Alignment on Electron Transport from Quasi-Two-Dimensional Iron Silicide α-FeSi{sub 2} Nanocrystals Into p-Si(001)

Self-assembled growth of α-FeSi{sub 2} nanocrystal ensembles on gold-activated and gold-free Si(001) surface by molecular beam epitaxy is reported. The microstructure and basic orientation relationship (OR) between the silicide nanocrystals and silicon substrate were analysed. The study reveals that utilisation of the gold as catalyst regulates the preferable OR of the nanocrystals with silicon and their habitus. It is shown that electron transport from α-FeSi2 phase into p-Si(001) can be tuned by the formation of (001)—or (111)—textured α-FeSi2 nanocrystals ensembles. A current-voltage characteristic of the structures with different preferable epitaxial alignment (α-FeSi{sub 2}(001)/Si(100) and α-FeSi{sub 2}(111)/Si(100)) shows good linearity at room temperature. However, it becomes non-linear at different temperatures for different ORs due to different Schottky barrier height governed by a particular epitaxial alignment of the α-FeSi{sub 2}/p-Si interfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2018

New Possible Structure of Silicide Mg{sub 2}Si under Pressure

As a result of an evolutionary search based on the density functional theory, a new low-symmetry structure of silicide Mg{sub 2}Si under pressure was discovered. This structure can exist along with the known structures of the symmetry Pnma and P63/mmc and is stable at a pressure of about 20 GPa. The lattice parameters of the discovered structure are in better agreement with the experimental values than the lattice parameters of the known structures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2016

Rate Theory Modeling and Simulation of Silicide Fuel at LWR Conditions

As a promising candidate for the accident tolerant fuel (ATF) used in light water reactors (LWRs), the fuel performance of uranium silicide (U 3 Si 2 ) at LWR conditions needs to be well understood. In this report, rate theory model was developed based on existing experimental data and density functional theory (DFT) calculations so as to predict the fission gas behavior in U 3 Si 2 at LWR conditions. The fission gas behavior of U 3 Si 2 can be divided into three temperature regimes. During steady-state operation, the majority of the fission gas stays in intragranular bubbles, whereas the dominance of intergranular bubbles and fission gas release only occurs beyond 1000 K. The steady-state rate theory model was also used as reference to establish a gaseous swelling correlation of U 3 Si 2 for the BISON code. Meanwhile, the overpressurized bubble model was also developed so that the fission gas behavior at LOCA can be simulated. LOCA simulation showed that intragranular bubbles are still dominant after a 70 second LOCA, resulting in a controllable gaseous swelling. The fission gas behavior of U 3 Si 2 at LWR conditions is benign according to the rate theory prediction at both steady-state and LOCA conditions, which provides important references to the qualification of U 3 Si 2 as a LWR fuel material with excellent fuel performance and enhanced accident tolerance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2016

Simulated Fission Gas Behavior in Silicide Fuel at LWR Conditions

As a promising candidate for the accident tolerant fuel (ATF) used in light water reactors (LWRs), the fuel performance of uranium silicide (U 3 Si 2 ) at LWR conditions needs to be well-understood. However, existing experimental post-irradiation examination (PIE) data are limited to the research reactor conditions, which involve lower fuel temperature compared to LWR conditions. This lack of appropriate experimental data significantly affects the development of fuel performance codes that can precisely predict the microstructure evolution and property degradation at LWR conditions, and therefore evaluate the qualification of U 3 Si 2 as an AFT for LWRs. Considering the high cost, long timescale, and restrictive access of the in-pile irradiation experiments, this study aims to utilize ion irradiation to simulate the inpile behavior of the U 3 Si 2 fuel. Both in situ TEM ion irradiation and ex situ high-energy ATLAS ion irradiation experiments were employed to simulate different types of microstructure modifications in U 3 Si 2 . Multiple PIE techniques were used or will be used to quantitatively analyze the microstructure evolution induced by ion irradiation so as to provide valuable reference for the development of fuel performance code prior to the availability of the in-pile irradiation data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2017

Radiation Re-solution Calculation in Uranium-Silicide Fuels

The release of fission gas from nuclear fuels is of primary concern for safe operation of nuclear power plants. Although the production of fission gas atoms can be easily calculated from the fission rate in the fuel and the average yield of fission gas, the actual diffusion, behavior, and ultimate escape of fission gas from nuclear fuel depends on many other variables. As fission gas diffuses through the fuel grain, it tends to collect into intra-granular bubbles, as portrayed in Figure 1.1. These bubbles continue to grow due to absorption of single gas atoms. Simultaneously, passing fission fragments can cause collisions in the bubble that result in gas atoms being knocked back into the grain. This so called “re-solution” event results in a transient equilibrium of single gas atoms within the grain. As single gas atoms progress through the grain, they will eventually collect along grain boundaries, creating inter-granular bubbles. As the inter-granular bubbles grow over time, they will interconnect with other grain-face bubbles until a pathway is created to the outside of the fuel surface, at which point the highly pressurized inter-granular bubbles will expel their contents into the fuel plenum. This last process is the primary cause of fission gas release. From the simple description above, it is clear there are several parameters that ultimately affect fission gas release, including the diffusivity of single gas atoms, the absorption and knockout rate of single gas atoms in intra-granular bubbles, and the growth and interlinkage of intergranular bubbles. Of these, the knockout, or re-solution rate has an particularly important role in determining the transient concentration of single gas atoms in the grain. The re-solution rate will be explored in the following sections with regards to uranium-silicide fuels in order to support future models of fission gas bubble behavior.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Phase equilibria of advanced technology uranium silicide-based nuclear fuel

The phases in uranium-silicide binary system were evaluated in regards to their stabilities, phase boundaries, crystal structures, and phase transitions. The results from this study were used in combination with a well assessed literature to optimize the U-Si phase diagram using the CALPHAD method. A thermodynamic database was developed, which could be used to guide nuclear fuel fabrication, could be incorporated into other nuclear fuel thermodynamic databases, or could be used to generate data required by fuel performance codes to model fuel behavior in normal or off-normal reactor operations. The U 3 Si 2 and U 3 Si 5 phases were modeled using the Compound Energy Formalism model with 3 sublattices to account for the variation in composition. The crystal structure used for the USi phase was the tetragonal with an I4/mmm space. Above 450°C, the U 3 Si 5 phase was modeled. The composition of the USi 2 phase was adjusted to USi 1.84 . The calculated invariant reactions and the enthalpy of formation for the stoichiometric phases were in agreement with experimental data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2016

Nano-scale mechanical behavior of uranium silicide compounds

Uranium silicide compounds exhibit a range of attractive material properties for nuclear fuel applications, but little is known regarding their mechanical behavior. The structure of nuclear fuels at high burnup can prove to be especially difficult given the significant changes in both chemistry and microstructure caused by fission products. Nano-indentation appears to be a valuable addition to post irradiation examination. The present focus is assessment of the room temperature modulus and hardness of U{sub 3}Si{sub 2}, U{sub 3}Si{sub 5} and USi materials. Each of the compositions under investigation was synthesized via arc melting of the pure metals in an Ar atmosphere using a titanium getter to remove O{sub 2} contamination. The resulting pellets following milling and sintering of the arc melted material were between 96 and 98% of density. Coupling different techniques (SEM and Chemical Analysis), microstructural investigations of the samples has been performed. Preliminary nano-mechanical response of U-Si fuel materials has been demonstrated, on a Hysitron Tribo-indenter which will impact the ability to design advanced fuel materials for enhanced high temperature performance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2016

Development of molecular dynamics potential for uranium silicide fuels

The use of uranium-silicide (U-Si) in place of uranium dioxide (UO{sub 2}) is one of the promising concepts being proposed to increase the accident tolerance of nuclear fuels for light water reactors. First-principles based density functional theory (DFT) electronic structure calculations may provide the most reliable information. However, it is probably not possible to obtain kinetic information such as amorphization under irradiation directly from DFT simulations due to size and time limitations. Thus, a more feasible way may be to employ molecular dynamics (MD) simulation. Unfortunately, so far no MD potential is available for U-Si to discover the underlying mechanisms. Here, we present our recent progress in developing a U-Si potential. The development is based on the Tersoff type potentials for single element U and Si. The Si potential is taken from the literature and a Tersoff type U potential is developed in this project. With the primary focus on the U{sub 3}Si{sub 2} phase, some other U-Si systems such as U{sub 3}Si are also included as a test of the transferability of the potentials for binary U-Si phases. Based on the potentials for unary U and Si, two sets of parameters for the binary U-Si system are developed using the Tersoff mixing rules and the cross-term fitting, respectively. The cross-term potential is found to give better results on the enthalpy of formation, lattice constants and elastic constants than those produced by the Tersoff mixing potential, with the reference data taken from either experiments or DFT calculations. In particular, the results on the formation enthalpy and lattice constants for the U{sub 3}Si{sub 2} phase and lattice constants for the high temperature U{sub 3}Si (h-U{sub 3}Si) phase generated by the cross-term potential agree well with experimental data. Reasonable agreements are also reached on the elastic constants of U{sub 3}Si{sub 2}, on the formation enthalpy for the low temperature U{sub 3}Si (m-U{sub 3}Si) and h-U{sub 3}Si phases, and on the lattice constants of m-U{sub 3}Si phase. All these phases are predicted to be mechanically stable. The unary U potential is also tested for three metallic U phases (α, β, γ). The potential is found capable to predict the cohesive energies well against experimental data for all three phases. It matches reasonably with previous experiments on the lattice constants and elastic constants of αU. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Challenges and opportunities to alloyed and composite fuel architectures to mitigate high uranium density fuel oxidation: uranium silicide

We report the challenges and opportunities to alloyed and composite fuel architectures designed and intended to mitigate oxidation of the fuel during a cladding breech of a water-cooled reactor are discussed in three review manuscripts developed in parallel, with the presented article focused on the oxidation performance of uranium silicide. Several high uranium density fuels are under consideration for deployment as accident tolerant and/or advanced technology nuclear reactor fuels, including UN, U 3 Si 2 , UC and UB 2 . Presented here are the literature for the U3Si2 degradation modes, thermodynamics, and oxidation performance of the pure compound and its reported alloyed and composite architectures. Furthermore, this review covers the materials and techniques for the incorporation of additives, dopants, or composite fuel architectures to improve the oxidation/corrosion behavior for high uranium density fuels for use in LWRs.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗