Chemical and thermal stability of thermoplastics in fast and mixed irradiation extremes
Not Available
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Not Available
The design and demonstration of an optical analysis system based on wavelength modulation spectroscopy in an atomic beam for uranium isotope abundance determinations is presented. This system probes the uranium 5f 3 6d7s 2 ( 5 L 6 ) → 5f 2 6d 2 7s 2 ( 5 K 5 ) transition at 861.031 nm, which is considered to be the most suitable transition for uranium isotopic analysis. A new laser characterization strategy was developed for the conditions where optimum laser wavelength modulation depth was small compared to the free spectral range (FSR) of etalons. Two capabilities enabled the higher-precision determination of isotope abundances of atomic beams: (1) reduction of low-frequency additive noise, especially the noise caused by black-body radiation and (2) suppression of non-absorption transmission losses. The performance of this system was validated with uranium samples of various isotopic compositions. Further, by comparing the measurements using natural uranium samples between the direct absorption and the wavelength modulation approaches, a 21-fold decrease in uncertainty of the integrated absorbance and a 6.8-fold improvement in the 1-σ precision of the number density were achieved. In addition, by comparing the results using uranium oxide samples, a 6.1-fold decrease in the uncertainty of inferred isotope abundance was obtained. These results demonstrate that the 1f-normalized 2f wavelength modulation spectroscopy (WMS-2f/1f) technique enables higher-precision analysis of atomic beams.
Quantifying the fission product 147 Nd in nuclear debris samples is an important component of post-detonation nuclear forensics. The most accurate quantifications are obtained when Nd is purified from all other fission products, actinides, activation products, and environmental matrix contained within the debris. In this study, a recently developed method for Nd purification was tested, purifying 147 Nd from solutions of mixed fission products using high-speed counter-current chromatography (HSCCC). Importantly, the new method allowed for faster elution of Nd from the column as compared with established high performance liquid chromatography (HPLC) methods, and resulted in accurate/precise 147 Nd quantification by gamma-ray spectrometry. While the up-front equipment costs associated with HSCCC may be higher, its operational costs are on par with those of HPLC (solvents, extractants, power). Gas-flow proportional beta decay counting revealed contamination from the nearest neighbor lanthanide 143 Pr (a gamma-silent radioisotope) in the HSCCC-purified samples, but the activity contribution from 147 Nd could still be quantified. Remarkably consistent elution profiles were observed for the HSCCC method, spanning rare earth element (REE) loadings of more than 10 orders of magnitude (tracer to mmol quantities). In conclusion, the reliability and speed of the new method suggest utility for the rapid separation and quantification of 147 Nd in unknown samples.
Bioreduction of hexavalent uranium (U(VI)) to tetravalent uranium (U(IV)) by dissimilatory metal-reducing bacteria (DMRB) is considered an effective strategy for uranium immobilization in contaminated environments. However, U(IV) can be reoxidized to U(VI) under fluctuating redox conditions and remobilized. This work investigates the oxidation behavior of biogenic U(IV) in the presence of bioreduced iron-bearing clay minerals (rNAu-2), iron-reducing bacteria (Shewanella putrefaciens CN32), and organic ligands (ethylenediaminetetraacetic acid (EDTA) and citrate). Results demonstrate that the presence of CN32 significantly inhibits U(IV) oxidation. rNAu-2 exerted a context-dependent influence on U(IV) oxidation: its effect was masked by bicarbonate-promoted U(VI) mobilization in the absence of active CN32, but became detectable when CN32-mediated microbial protection slowed U(IV) oxidation. EDTA and citrate markedly accelerate U(IV) oxidation via formation of soluble U(IV)-ligand complexes, changing U(IV) redox potentials, and by promoting clay mineral dissolution that enhances Fe(II)/Fe(III) redox cycling. Collectively, our findings constrain the roles that clay minerals, iron-reducing bacteria, and organic ligands play in governing U(IV) stability, emphasizing the need to account for these factors in developing robust bioremediation strategies.
The crystal structure of perfluorononanoic acid (PFNA) was solved via parallel tempering using synchrotron powder diffraction data obtained from the Brockhouse X-ray Diffraction and Scattering (BXDS) Wiggler Lower Energy (WLE) beamline at the Canadian Light Source. PFNA crystallizes in monoclinic space group P2 1 /c (#14) with lattice parameters a = 26.172(1) Å, b = 5.6345(2) Å, c = 10.9501(4) Å, and β = 98.752(2)°. The crystal structure is composed of dimers, with pairs of PFNA molecules connected by hydrogen bonds via the carboxylic acid functional groups. The Rietveld-refined structure was compared to a density functional theory-optimized structure, and the root-mean-square Cartesian difference was larger than normally observed for correct powder structures. The powder data likely exhibited evidence of disorder which was not successfully modeled.
Understanding how thermal history influences redox evolution and chemical fractionation is essential for characterizing high-temperature condensation in complex materials, including nuclear debris. Here, we tested the hypothesis that distinct thermal regimes in a plasma flow reactor influence redox pathways and elemental partitioning in ternary U/Ce/Cs systems. A configurable plasma flow reactor was modified with an external tube furnace to impose two distinct thermal gradients: continuous ambient cooling and a furnace-assisted thermal hold-up near 1400 K followed by rapid cooling. Transmission electron microscopy characterized phase identity, morphology, and nanoscale element distributions, while inductively coupled plasma-mass spectrometry quantified bulk elemental ratios. Across both thermal regimes, uranium and cerium condensed as UO 2 and CeO 2 as dominant refractory oxide products. Uranium partially oxidized to α-UO 3 during extended ambient cooling, while furnace-assisted hold-up preserved UO 2 and produced partial reduction of cerium to Ce 2 O 3 . Cesium remained volatile upstream and condensed later in the reactor, forming Cs 2 O and Cs-uranate phases with the highest incorporation after thermal hold-up. Bulk ICP-MS measurements supported these observations. U/Ce ratios remained comparatively stable and Cs displayed delayed and apparent transient enrichment that matched the nanoscale measurements. This integrated approach provides a quantitative method for linking thermal gradients to redox evolution and volatility-driven fractionation. These results show how the plasma flow reactor can identify where equilibrium descriptions remain adequate and where kinetic effects from residence time and temperature history must be considered when interpreting condensation behavior in multicomponent systems.
Uranyl peroxide complexes, particularly studtite (UO 4 ·4H 2 O), are important phases within the nuclear fuel cycle, forming through radiolysis-induced reactions on the surfaces of spent fuel and in waste environments. Studtite has been identified in Hanford’s irradiated fuel storage basins, Chornobyl’s corium lavas, and is anticipated on Fukushima’s fuel debris. While its formation and stability have been extensively studied, the reactivity of UO 4 ·4H 2 O in highly alkaline environments such as those encountered in high-level nuclear waste remains underexplored. These environments contain molar concentrations of [OH - ] and present a chemically dynamic and reactive environment where actinide behavior is not well understood. Reported here are investigations of uranium reactions in concentrated alkali hydroxides under mild hydrothermal conditions (<200 °C) that have resulted in the isolation of the alkali metal uranates Li 2 UO 4 , α-Na 2 UO 4 , γ-Na 2 U 2 O 7 , and K 2 U 2 O 7 . In contrast to conventional solid-state methods (>800 °C) that typically yield polycrystalline powders, our approach enables the isolation of these uranates as single crystals, allowing us to provide single-crystal structure solutions of certain uranates for the first time. Our findings match the results of high-level waste tank sampling, confirming that sodium diuranate (Na 2 U 2 O 7 ) is the most persistent uranium phase, potentially forming through reactions of uranyl peroxide intermediates with NaOH under radiolytic and highly alkaline conditions.
Here, in this work, we examine how radiation impacts the dissolution behavior of boehmite by subjecting dry nanoparticles of different sizes to 60 Co γ radiation and subsequently analyzing their dissolution behavior in caustic solutions as a function of temperature. The measured kinetics show that irradiation with an amount 228.24 Mrad significantly slows the dissolution rate, particularly for smaller sizes at lower temperatures. Specifically, the temperature-dependent dissolution rates of irradiated 20 nm boehmite versus pristine material in 3 M NaOH solutions were several times lower (e.g., rate constant of 0.026 vs 0.075 h –1 at 60 °C), with an apparent activation energy 40 kJ mol –1 higher. Although various imaging techniques and X-ray diffraction measurements consistently revealed no obvious differences between pristine and irradiated samples, after irradiation significant binding energy shifts were detected in the X-ray photoelectron Spectroscopy peaks of Al 2p and O 1s, and a change in their relative intensities indicated a lower O/Al ratio. This suggests that γ-irradiation may stabilize boehmite particle surfaces by driving their chemistry and structure toward more stable aluminum oxide forms. This finding may help explain slower dissolution rates of boehmite in nuclear waste and may be useful for the development of more robust predictive models and effective strategies for waste processing.
Extraction of neptunium from acidic matrices is important for its quantification, but its complex redox chemistry can cause variable yields. This study develops a microfluidic redox extraction for rapidly separating neptunium from submilliliter samples, achieving up to 90% process yield in less than 10 min for samples as small as 100 μL, with over 97% steady-state yield achieved after 20 min. It uses a supported liquid membrane module loaded with 30 vol % tributyl phosphate in n-dodecane, which performs forward- and back-extractions in a single, continuous step. Neptunium is first oxidized to +6 for extraction and then reduced during stripping. Bromate was selected as an oxidant over permanganate for its greater compatibility with the organic phase, achieving complete oxidation in under 30 s. Ascorbic acid and hydrogen peroxide were both effective reductants. Finally, the system’s high yield and rapid kinetics make it promising for future separations from complex mixtures.
The selective partitioning of americium (Am) and curium (Cm) is integral for nuclear science areas such as the nuclear fuel cycle, stockpile stewardship, and isotope production but remains a long-standing radioanalytical challenge due to nearly identical chemical properties. Differences in redox chemistry can be exploited since Am can be oxidized to the hexavalent oxidation state. Sodium bismuthate (NaBiO 3 ) exhibits favorable oxidation and ion exchange characteristics conducive to a rapid and efficient Am/Cm chromatographic separation. Contact of nitric acid with NaBiO 3 was shown to significantly decrease the nitric acid concentration and solution volume. The adsorption, kinetic, and chromatographic behavior of Am and Cm in systems that disperse NaBiO3 in filter aids was evaluated. Further, dispersion of NaBiO 3 increased separation factors to over 100, with rapid kinetics achieved within 1 min of contact and sustained for at least 2 h. The adsorption capacity was more than doubled from 0.066 mequiv g –1 for solid NaBiO 3 alone to 0.149(6) and 0.156(9) meq g –1 when dispersed in Celite 545 and silica gel, respectively. Complete separation was achieved in all systems with ~100% recovery in the respective eluted fractions.
Advanced sulfur chloride-based chlorination technologies are being developed to enable efficient recycling of aluminum and zirconium-based materials used in the nuclear industry. However, the impacts of ionizing radiation on the performance of these sulfur chloride compounds are not well established, despite this being critical knowledge for assessing their feasibility and longevity under envisioned process conditions. Here, in the present article, we report on the effects of cobalt-60 gamma irradiation (≤ 5 MGy) on the aluminum alloy 6061 (AA6061-T6) chlorination yield in sulfur monochloride (S 2 Cl 2 ). Our findings indicate that, compared to nonirradiated solvent, radiation-induced changes in the chemical composition of S 2 Cl 2 —identified using Raman spectroscopy—afford an additional, dose-dependent exothermic process prior to the chlorination reaction’s typical thermodynamic behavior. We attribute this new process to reactions involving aluminum species (metal, oxide, or [oxy]hydroxides) and sulfur dichloride (SCl 2 ), an S 2 Cl 2 radiolysis product that accumulates with absorbed gamma dose, but is absent following an AA6061-T6 chlorination study. Despite the exothermicity of this new process, the overall yield of chlorination decreased with increasing preirradiation dose. Consequently, the chemical reactivity, specificity (aluminum metal vs aluminum passivation and corrosion layer constituents), and byproducts of SCl 2 must be more thoroughly evaluated to support the continued development of advanced S 2 Cl 2 chlorination technologies.
Nuclear material operations pose unique hazards that are not encountered in other chemical, energy, or manufacturing industries. One of these hazards is the potential for a nuclear criticality accident when handling fissile isotopes such as 235 U and 239 Pu. These hazards are particularly high when fissile material is dissolved in solution as the neutron behaviors of the system can change rapidly with the physical and chemical changes accessible in solution. Current estimates of solution density used for criticality safety are outdated and hinder fissile material handling. Developing new estimates for these safety calculations requires experimental characterization and the derivation of empirical density models. We have derived a density law describing PuCl 3 /HCl/H 2 O solutions from experimental data characterizing solution density. Density data was treated using a Pitzer-derived eight-parameter equation, defining density as a function of analyte concentrations, temperature, and interactions between these variables. The model is predictive across the concentration and temperature ranges from which it was derived. The potential effects of varying oxidation states of plutonium, which are easily accessible in aqueous media, on the bulk solution density of the ternary system were also investigated. The resulting Pitzer-derived density law was applied to a nuclear criticality safety model, and the impact of the experimental characterization of solution density relative to previous estimates was demonstrated to be significant and suggest that the current approach to estimating density in nuclear criticality safety calculations may lead to overly conservative controls.
Explore the source record for details and available documents.
Amidate-based ligands (N-(tert-butyl)isobutyramide, ITA) bind κ 2 to form homoleptic, 8-coordinate complexes with tetravalent 237 Np (Np(ITA) 4 , 1-Np) and 242 Pu (Pu(ITA) 4 , 1-Pu). These compounds complete an isostructural series from Th, U–Pu and allow for the direct comparison between many of the early actinides with stable tetravalent oxidation states by nuclear magnetic resonance (NMR) spectroscopy and single crystal X-ray diffraction (SCXRD). The molecular precursors are subjected to controlled thermolysis under mild conditions with the exclusion of exogenous air and moisture, facilitating the removal of the volatile organic ligands and ligand byproducts. The preformed metal–oxygen bond in the precursor, as well as the metal oxidation state, are maintained through the decomposition, forming fully stoichiometric, oxidation-state pure NpO 2 and PuO 2 . Powder X-ray diffraction (PXRD), scanning transmission electron microscopy (STEM), and energy dispersive X-ray spectroscopy (EDS) elemental mapping supported the evaluation of these high-purity materials. This chemistry is applicable to a wide range of metals, including actinides, with accessible tetravalent oxidation states, and provides a consistent route to analytical standards of importance to the field of nuclear nonproliferation, forensics, and fundamental studies.
While uranium is the most extensively studied actinide in terms of chemical properties, there remains much to be explored about its fundamental chemistry. Organometallic and organoactinide chemistry first emerged in the 1950s with research that found inspiration from transition-metal chemistry with the synthesis and characterization of uranocene, expanding new opportunities for organoactinide chemistry. Since then, a significant amount of research has pursued many avenues characterizing the fundamental nature of the f orbitals and their modes of bonding as well as their potential in catalysis. Uranium(III/IV) arene complexes dominate much of uranium organometallic chemistry, with bonding interactions stabilized by δ-back-bonding. Recent additions to this area of chemistry include the first UI and new additions of U II organouranium compounds. Uranium–transition metal complexes are still rare and maintain U IV oxidation states, with variable bond lengths determining the transition-metal oxidation state. Resultant reactivities are discussed as synthetic complexes, and unique bonding and coordination motifs are highlighted. In conclusion, this Viewpoint will focus on significant developments in uranium chemistry from the last 15 years while considering key areas for future research.
Here, we report the isolation of the first plutonium(IV) complex with a Keggin ion chelator: Cs 20 [Pu(PW 11 O 39 ) 2 ] 2 ·13H 2 O. Single crystal XRD and solid-state UV–vis absorbance analysis demonstrate the stabilization of Pu 4+ by the Keggin ligand. The unit cell contains two [Pu(PW 11 O 39 ) 2 ] 10– complexes (Pu(PW 11 ) 2 ) bridged by Cs + . Raman and 31 P NMR spectra of Pu(PW 11 ) 2 are consistent with the analogous Zr 4+ , Hf 4+ , Ce 4+ , and Th 4+ complexes. The Pu–O bond distances at the two Pu sites are 2.35(3) and 2.34(3) Å, matching the value extrapolated from the bonding trend built with the other 8-coordinated tetravalent cations. However, the long-range arrangement of the Pu(PW 11 ) 2 complexes within the lattice is unique in the series of M IV (PW 11 ) 2 compounds: pairs of Pu(PW 11 ) 2 are organized perpendicular to each other. Based on solution-state UV–visible absorbance, small-angle X-ray scattering (SAXS), and 31 P NMR, the tetravalent cations quantitatively form the 1:2 species in solution ([Pu(PW 11 O 39 ) 2 ] 10– (aq) ) and no 1:1 species ([Pu(PW 11 O 39 )(H 2 O) x ] 3– (aq) ). Finally, a linear correlation exists between the metal–oxygen distances in the M IV (PW 11 ) 2 compounds and the corresponding metal dioxides, allowing for extrapolation for Pa 4+ , Am 4+ , and Bk 4+ . The results indicate that our microscale POM approach represents a viable pathway to probe properties of rare actinide ions in discrete molecules, beyond the traditional oxide extended solids.
In the pyrochemical reprocessing of used nuclear fuel, understanding the effects of ionizing radiation on the chemical behavior of fission products in molten chloride eutectic salt is crucial. Here, this study investigates the impact of radiation on the chemical and kinetic speciation of Nd ions in molten LiCl-KCl eutectic, which are challenging to separate due to their multivalent oxidation states and comproportionation reactions. Electron pulse radiolysis techniques were used to determine transient absorption spectra, chemical kinetics, and activation parameters for the reaction of Nd ions with the primary products of molten LiCl-KCl eutectic radiolysis: the solvated electron (e S - ) and dichlorine radical anion (Cl 2 •- ). Initially, Nd(III) reacted rapidly with e S - , forming Nd(II) with a second-order rate coefficient of k = (4.54 ± 0.07) × 10 10 M -1 s -1 at 673 K. The resulting Nd(II) ions then reacted slowly with Cl 2 •- , regenerating Nd(III) with an estimated rate of k = (1.72 ± 0.04) × 10 10 M -1 s -1 at 673 K. Additionally, the comproportionation reaction of Nd(III) and Nd(s) to form Nd(II) was monitored chemically and electrochemically. This work suggests that the comproportionation reaction of Nd(III) with Nd(s) to form Nd(II) is unstable in molten LiCl-KCl eutectic.
Radioactive decay of uranium (U) and its related daughter/fission products emit ionizing radiation, including γ (γ) rays and α (α) particles, that result in the formation of radical species and induce chemical reactivity in materials. While radioactivity is inherent to the chemistry of U there are limited studies that detail changes at an atomistic level. Here, this work describes the He-ion radiolysis of four solid-state U(VI) species: [UO 2 (NO 3 ) 2 ]·3(H 2 O) and M[UO 2 (NO 3 ) 3 ] (M = K + , Rb + , Cs + ). These materials were irradiated under different conditions (i.e. closed, open – Ar gas, or open – H 2 O-saturated Ar gas) to further evaluate the impact of water radiolysis on the chemical modification of these materials. Pre- and post-irradiation analyses were conducted using EPR, Raman, and ATR-IR spectroscopy on materials irradiated to 0, 5, 10, and 25 MGy. The results indicated the presence of nitrate radical (NO 3 • ) formation in all solid-state materials with similarities to those observed in γ-radiation studies. Irradiation of [UO 2 (NO 3 ) 2 ]·3(H 2 O) did not show evidence of reactive oxygen species bound to the U(VI) cation under inert conditions; however, surface reactivity was observed for samples irradiated in the H 2 O-saturated environment. Similar chemical changes were observed in the uranyl trinitrato compounds irradiated in the presence of H 2 O vapor and there were observed differences in the reactivity depending on the identity of the alkali cation.