Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Post-irradiation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Fission Product Quantification and Burnup Analysis via Gamma Spectrometry of the AGR-5/6/7 TRISO Fuel Experiment

Five capsules containing varying configurations of TRISO fuel compacts were irradiated in the most recent Advanced Gas Reactor (AGR) TRISO test campaign, AGR-5/6/7. As part of the post-irradiation examination (PIE) of this work all the fuel compacts and capsule graphite holders were measured with the Precision Gamma Scanner (PGS) to determine isotopic activities and locations using gamma spectrometry. Measuring the compacts allowed for the comparison of physics model depletion calculations with the measured compact activity to validate models. These measurements also are used to find compacts of interest with low fission product retention that may be tested in subsequent PIE. Measurements of the holders can confirm fission product distribution and migration. Of the isotopes measured, Cs-137 and Cs-134 were used to estimate location of failed particles as well as determine a measured burnup estimation. Results from Capsule 1 compacts and the holder indicate many fuel particle failures occurred. There are high amounts of cesium in the holder near Stack 9 of Capsule 1 that corresponds to low fractions?measured-to-calculated (M/C) ratio?of cesium remaining in those compacts. All other capsules had cesium retention ratios near 1. The isotope 110mAg had less consistent results. Capsule 2 compacts exhibited a M/C of 0.20, much lower than anticipated for the temperatures these compacts underwent. Capsule 3 experienced much higher temperatures, >1300C and had an average M/C of 0.75. These are the opposite results than what was predicted by past AGR experiments for the relationship between temperature and isotope retention. Capsule 4 and 5 showed good fission product retention and agreement with the physics model predictions. The burnup results from the PGS measurements showed strong agreement between the physics models and the measured values. Using a ratio of Cs-134/Cs-137 to calculate the burnup match closely with the physics models. Additionally, the Cs-137 burnup results were less accurate but extremely close to the model results.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Production Target Studies at the M4 Diagnostic Absorber

High power production targetry is becoming essential to the future of HEP, but our current physics simulations are lacking validation in the lower energy ranges that many proposed secondary beam experiments will use. We propose a study of target materials at the M4 diagnostic absorber to monitor target temperatures during irradiation by an 8 GeV proton beam and provide some experimental validation for our simulations at lower energies as well as potentially perform post-irradiation examination of samples to understand changes to material properties.

Bloomer, Madeleine [UC, Davis] (ORCID:000900080329↗
DOE OSTI2025

Advanced Manufactured Strain Sensors for Extreme Environments

Experimentation at irradiation test facilities are essential for reducing the innovation time of developmental fuels, fuel cladding, and structural materials employed in next-generation nuclear reactors. However, due to the harsh conditions generated in such reactors and limited instrumentation space, the evaluation of a material’s mechanical properties is often limited to characterization after the materials have been removed from reactor conditions, or post-irradiation examination. These experiments are costly, time-consuming, and fail to capture the critical time-evolving phenomena that occur during the irradiation experiments. Advanced manufactured digital image correlation patterns and strain sensor devices serve as two promising technologies that can be deployed in the confined and challenging orientations of these irradiation experiments while also providing key insight on salient materials phenomena (i.e., mechanical properties). To guide the development of the printed strain sensors prior to their deployment in critical experiments, the adhesion strength between the substrate and printed film interface is measured via tensile testing and a non-contact laser-induced spallation technique. The establishment of these process control steps helped guide the successful fabrication and testing of direct-write strain sensing devices discussed in this work. The fabrication process controls are necessary for enabling the sustained operation of these strain sensing device through experimentation and minimize the potential for premature failure.

36 - MATERIALS SCIENCE↗
DOE OSTI2026

Microscopy and Characterization Suite (MaCS) and National Synchrotron Light Source-II (NSLS-II) FY 2025 Annual Report

The Microscopy and Characterization Suite (MaCS) laboratory at the Critical Materials and Energy Systems Innovation Center (CMESIC), formerly the Center for Advanced Energy Studies (CAES) and the National Synchrotron Light Source-II (NSLS-II) at Brookhaven National Laboratory (BNL) partner with the Nuclear Science User Facilities (NSUF). These partnerships provide funding that allows researchers to access these facilities at no cost for studying irradiation effects on nuclear fuels and materials. Through NSUF, both MaCS and NSLS-II support post-irradiation examination (PIE) and irradiation activities for NSUF Rapid Turnaround Experiments (RTE) and NSUF Consolidated Innovative Nuclear Research (CINR) awards.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

AGR 1 and 2 Isotopic Depletion Validation

This presentation includes work performed developing a computational benchmark for the AGR 1 and 2 experiments. These experiments involve irradiation of TRISO particle compact in the Advanced Test Reactor (ATR). Many post-irradiation measurements were made from these experiments, including isotopic concentrations of fission products. The benchmark involves a MCNP-ORIGEN coupled model of the ATR and AGR experiment capsules to calculate a comprehensive inventory of fission product and actinide concentrations in the compacts. This presentation describes the experiments, the measurements obtained, the benchmark model, and results of the model evaluation.

97 - MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Advanced Manufactured Strain Sensors for Extreme Environments

Experimentation at irradiation test facilities are essential for reducing the innovation time of developmental fuels, fuel cladding, and structural materials employed in next-generation nuclear reactors. However, due to the harsh conditions generated in such reactors and limited instrumentation space, the evaluation of a material’s mechanical properties is often limited to characterization after the materials have been removed from reactor conditions, or post-irradiation examination. These experiments are costly, time-consuming, and fail to capture the critical time-evolving phenomena that occur during the irradiation experiments. Advanced manufactured digital image correlation patterns and strain sensor devices serve as two promising technologies that can be deployed in the confined and challenging orientations of these irradiation experiments while also providing key insight on salient materials phenomena (i.e., mechanical properties).To guide the development of the printed strain sensors prior to their deployment in critical experiments, the adhesion strength between the substrate and printed film interface is measured via tensile testing and a non-contact laser-induced spallation technique. The establishment of these process control steps helped guide the successful fabrication and testing of direct-write strain sensing devices discussed in this work. The fabrication process controls are necessary for enabling the sustained operation of these strain sensing device through experimentation and minimize the potential for premature failure.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

NDMAS

Overview of Current ART-GCR Data: Fuel Fabrication, Irradiation Monitoring (Fuel & Graphite – near real-time for HDG-1), Post-Irradiation Examination (Fuel & Graphite), Graphite Characterization (Baseline and Irradiated), High Temperature Metals Mechanical Tests, Design, Methods, and Validation Data, Japan Atomic Energy Agency’s High Temperature Test Reactor (HTTR), Argonne National Laboratory’s Natural convection Shutdown heat removal Test Facility (NSTF), Oregon State University’s High Temperature Test Facility (HTTF), Generation IV International VHTR Materials Handbook, Additional related data, and Advanced Test Reactor operations (near real-time).

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Characterization of Pinhole Collimators for High-Resolution Gamma Imaging of Irradiated Fuel

Post-irradiation examination (PIE) of nuclear fuels requires imaging tools capable of resolving isotopic and spatial features with high throughput. This project contributes to a proof-of-concept effort aimed at advancing gamma emission tomography (GET) by evaluating novel fine-aperture pinhole collimators. Two Rose’s metal collimators, 100 µm (20° acceptance angle) and 350 µm (30° acceptance angle), were prototyped and characterized for their effectiveness in transporting gamma rays through the pinhole aperture. To support data collection, a Python-based data acquisition system was developed to coordinate a rotation stage, linear stage, and CZT detector, reducing latency in high-rate gamma event logging to one second per acquisition. Queue-based file writing enabled seamless real-time data capture for count rates up to 35,000 counts per second (cps). List-mode parsing algorithms were implemented to differentiate single and simultaneous gamma interactions for future tomographic reconstruction. Detector response was evaluated in both spectroscopy and list mode acquisition methods across varying source distances to confirm absolute and collimator efficiencies. Preliminary efficiency figures suggest effective collimation of gamma-rays with energies below 700 keV, with ~4% residual intensity through the aperture for Cs-137. The impact of collimator geometry on image quality is currently being evaluated. This groundwork supports the ongoing development of a sub mm resolution cone-beam CT system for imaging fuel phantoms, an essential step toward improving GET efficiency and accelerating nuclear fuel qualification efforts.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗
DOE OSTI2025

Assessment of buffer-IPyC thermomechanical debonding behavior using new experimental strength data in BISON

TRIstructural ISOtropic (TRISO) fuel is a nuclear fuel commonly used in High Temperature Gas-cooled Reactors (HTGRs). A single sub-millimeter-diameter TRISO fuel particle consists of a spherical fuel kernel surrounded by four coating layers: a low-density pyrocarbon buffer layer, an inner pyrolytic carbon (IPyC) layer, a silicon carbide (SiC) layer, and an outer pyrolytic carbon (OPyC) layer. The kernel is commonly made of UO2 or a mixture of uranium carbide and uranium oxide (UCO). During reactor operation, the TRISO coating layers are subjected to irradiation-induced dimensional changes and the associated thermomechanical behavior of each layer. One of the observed behaviors is gap formation between the buffer and IPyC layer due to the porous buffer’s irradiation-induced shrinkage exceeding that of the IPyC layer. Not all irradiated particles will experience buffer-IPyC gap formation. The debonding may be partial, or it may be nearly total. However, from post-irradiation examination of UCO TRISO fuels irradiated as part of the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program, it was concluded that partial buffer-IPyC debonding was the most common type of buffer-IPyC interaction. To predict TRISO thermomechanical performance, multi-physics models have been built that are being continually updated and refined. The BISON code is a finite element-based nuclear fuel performance code that may be used for 1D, 2D, and 3D TRISO particle simulations. This code is used to calculate fuel temperature, kernel swelling, buffer densification, thermal and irradiation creep, fracture, and fission gas production and release. One of the recent additions to the BISON code is the ability to model the process of layer debonding. This paper will focus on the simulation results of the improved BISON debonding model that will utilize updated strengths measured from irradiated AGR TRISO fuel particles. The new experimental strength data from micromechanical tests of irradiated TRISO fuel samples were exercised in the BISON simulations and compared to baseline strength data to assess their applicability in the models. This also includes updated buffer-IPyC bond strengths to simulate layer delamination. Based on current experimental observations it is noted that the buffer-IPyC separation occurs not exactly at the junction of these two layers, but more on the side of the buffer layer. That observation is also implemented in the TRISO interface debonding model. This improved modeling approach using experimental strength data to characterize buffer-IPyC debonding and its potential subsequent cracking will be presented in the paper along with comparisons to available experimental observations.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

AGR-5/6/7 Ceramography Report

The Advanced Gas Reactor (AGR) Fuel Development and Qualification Program was established in 2002 to conduct research and development on tri-structural isotropic (TRISO)-coated particle fuel for High Temperature Gas-cooled Reactors (HTGRs). All AGR irradiations have been completed: AGR-1 (Collin 2015), AGR-2 (Collin 2014), AGR-3/4 (Collin 2016) and AGR-5/6/7 (Pham 2021). The objectives of each program are presented in Figure 1.1. The purpose of the AGR-5/6/7 program was to provide a baseline fuel qualification data set to support licensing, deployment, and operation of HTGRs in the United States. To achieve these goals, the program includes fuel fabrication, irradiations of TRISO fuels and high-temperature materials, safety testing and post-irradiation examination (PIE), fuel performance modeling, and fission product (FP) transport (Sharp 2020). The AGR-5/6/7 work continues as a final irradiation program of the Advanced Reactor Technologies (ART) program, that began in February 2018 and ended in July 2020. The AGR-5/6/7 fuel compacts were irradiated for a total of approximately 360.9 effective full power days (EFPDs) (Stempien 2023), resulting in final burn-up values, on a per-compact basis, ranging from 5.66% to 15.26% fissions per initial heavy metal atom (FIMA), and fast fluence values ranging from 1.62×1025 n/m2 to 5.55×1025 n/m2 (E >0.18 MeV) (Stempien 2022)

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Defining Probe Closure Offset and Scan Stitching Methodology for Element Contact Profilometry in the Hot Fuel Examination Facility

The Element Contact Profilometer (ECP) is a non-destructive post-irradiation examination (PIE) method established in the Materials and Fuels Complex (MFC) Hot Fuel Examination Facility (HFEF). The ECP suspends a fuel rod with a standard end-fitting in a vertical orientation and draws it between two opposed Sony probes with sapphire rod tips, which measure the diameter directly as a function of vertical stage position through contact profilometry. The ECP is equipped with concave rollers, which pinch the rod to maintain a consist position between these sapphire probe tips. A schematic of the analysis head is shown in Figure 1. The gripper that suspends the rod end-fitting is able to rotate to allow measuring of any azimuthal angle around the rod. This system is used to characterize the diameter of full-length light water reactor (LWR) irradiated fuel rods at multiple azimuthal angles in support of the Advanced Fuels Campaign (AFC).

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

AFC FAST Status Report Fiscal Year 2025

The Fission Accelerated Steady-state Test (FAST) methodology has been used to test several innovative metallic fuel designs for use in Sodium?cooled Fast Reactors (SFRs). The FAST method utilizes geometrically scaled fuel pins to produce improved burnup rates for fuels while maintaining semi-prototypic thermal conditions. This report provides a summary description of the test matrix and test objectives for the AFC FAST irradiation campaign as well as details of the as-built conditions for all rodlets. This report also include status update on the irradiation conditions for the rodlets as well as post-irradiation examination (PIE) results on low to mid?range burnup fuel rodlets and a summary power history for those rodlets. A brief discussion provides some early interpretation of the results and whether or not FAST is producing results typical of metallic fuels. Lastly, an outlook for the work expected to be completed in fiscal year (FY) 2026 is also included.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Enabling In-Core Strain Measurement: Printed Sensors for Advanced Reactors

Advances in nuclear energy systems require an improved understanding of fuels, cladding, and structural materials; however, the extreme environmental conditions at irradiation test facilities often limit mechanical property evaluation to post-irradiation examination. In-situ monitoring techniques can accelerate materials qualification by providing direct insight into real-time material behavior during irradiation testing. Additively manufactured (AM) strain gauges offer a compact, material-compatible alternative to commercial sensors, particularly where space constraints, attachment limitations, or material compatibility requirements complicate conventional sensor use. This poster presents an overview of the development and testing of AM strain gauges in nuclear-relevant environments, demonstrating their potential to enhance structural health monitoring capabilities during irradiation experiments.

36 - MATERIALS SCIENCE↗
DOE OSTI2026

Mechanical Behavior of Neutron Irradiated Refractory Multi-Principal Element Alloys Processed via Spark Plasma Sintering

The search for advanced materials capable of withstanding the extreme conditions of Generation IV reactors is a critical area in materials science research. These reactors operate under severe environments, including high temperatures, corrosion, stress, and irradiation damage. Consequently, there is a need for innovative alloy systems to ensure the reliability and longevity of proposed Generation IV reactor components. Refractory multi-principal-element alloys (RMPEA) have emerged as a promising candidate due to their exceptional properties. These alloys, characterized by their composition of multiple principal elements in near-equiatomic ratios, exhibit superior resistance to irradiation damage, reduced void swelling, enhanced microstructural stability, and minimal irradiation-induced hardening. While initial studies on RMPEAs have shown promising results, most research has been limited to thin films, nanocrystalline microstructures, and ion irradiation, which do not accurately represent the behavior of bulk materials. To address this gap, our research focused on the neutron irradiation of bulk RMPEAs. We aim to conduct comprehensive post-irradiation examinations (PIE) of RMPEAs irradiated at the Advanced Test Reactor at Idaho National Laboratory. The RMPEAs were synthesized using spark plasma sintering (SPS) with mechanically alloyed metallurgical powder. The RMPEA specimens are a MoNbTi alloy system with additions of -Zr, and -ZrV. Furthermore, PIE consisted of mechanical testing and advanced materials characterization. The mechanical testing consisted of sub-sized tensile testing, micro- and nano- indentation. Microstructural characterization included scanning electron microscopy and transmission electron microscopy. Mechanical testing coupled with advanced microscopy techniques provides insight into phase morphology and its effects on the mechanical properties of the RMPEA specimens. The results indicate that both pristine and irradiated RMPEA specimens exhibited brittle behavior during tensile testing, which can be attributed to their heterogeneous microstructure. The SPS manufacturing process did not include any post treatment, which resulted in a heterogeneous microstructure. Energy-dispersive X-ray spectroscopy revealed the presence of intermetallic such as laves phases within the microstructure. Specifically, Ti-rich precipitates were observed in the MoNbTi specimen, while Mo-rich precipitates were found in the MoNbTiZrV specimen. Nano-hardness testing of pristine samples showed that the laves phases exhibited higher hardness values compared to the matrix phase, suggesting that precipitate hardening is likely the dominant hardening mechanism in these specimens. The results from this work will be used to build a finite element model to predict mechanical behavior of future MPEA compositions. Thus, enabling for a streamlined approach to developing novel MPEAs for the nuclear industry.

36 - MATERIALS SCIENCE↗
DOE OSTI2026

EDS Analysis of FCCI in AFC-FAST Fuel Pins

The Advanced Fuel Campaign’s Fission Accelerated Steady-state Testing (FAST) program uses metallic fuel pins with small diameters to reach a desired burnup more quickly. This enables accelerated testing of advanced fuel designs and decreases the time between idea conception and commercial usage. Post-irradiation examination is critical in this process, especially with respect to the fuel-cladding chemical interactions (FCCI). In this work, energy dispersive X-ray spectroscopy (EDS) is used to track how elements from the fuel and fission products have diffused through the cladding. Elemental redistribution along the fuel-cladding interface is mapped and FCCI region thicknesses are measured. The correlations between geometry, temperature, burnup, and FCCI thickness are presented.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Through-thickness fracture behavior of neutron-irradiated nuclear graphite NBG-17 Using X-ray micro-CT

Achieving precise control over crack propagation in nuclear graphite and conducting quantitative analysis remain challenging. In this study, the through-thickness fracture behavior of pristine and neutron-irradiated (700 °C, ∼7 dpa) NBG-17 nuclear graphite was investigated using split-disc testing coupled with micro-computed tomography (micro-CT). A notably lower number of micropores was observed in the neutron-irradiated specimen. The fracture toughness of neutron-irradiated NBG-17 was measured to be 1.45 MPa√m, compared to 1.17 ± 0.05 MPa√m for the pristine specimen. In both materials, cracks were found to initiate at the filler–binder interface, and often correlated with microstructural features such as pores and thermal cracks. Crack bridging and deflections emerged as the primary toughening mechanisms in both unirradiated and irradiated NBG-17. However, compared with the pristine specimen, the cracks in the neutron-irradiated specimen were more likely to grow trans granularly, resulting in less deflected crack paths. The reduced micro-porosity and strengthened filler–binder boundaries were considered to be the cause of the observed differences in crack morphologies. In conclusion, this study provides a qualitative analysis of the fracture behavior of neutron-irradiated nuclear graphite in the absence of radiolytic oxidation.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Microscopic analysis of irradiated UN–Mo–W for space nuclear propulsion

Nuclear propulsion is an effective method of providing thrust in deep space, allowing for shorter mission duration for long-term surface missions to Mars. The fuel for nuclear propulsion systems must exhibit superior mechanical and thermal properties, to decrease the possibility of fuel failure and to increase reactor efficiency. Here, the objective of the Sirius project is to fabricate and irradiate cermet fuels at the Idaho National Laboratory Transient Reactor Facility to determine the properties of the fuel after irradiation at prototypical nuclear propulsion start-up conditions. The Sirius project featured 3 test capsules, Sirius-1 featured uranium nitride fuel dispersed in a matrix of tungsten and rhenium, while Sirius-2A and -2B featured uranium nitride-molybdenum-tungsten fuel (UN-Mo-W). The fuel samples from the Sirius-2A and -2B capsules were examined after irradiation using optical microscopy, scanning electron microscopy, and X-ray diffraction analyses. The mechanical properties of the fuel from Sirius-2A and -2B are discussed in a previous work. In this study, the results of the optical microscopy, scanning electron microscopy, and X-ray diffraction analyses are discussed.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Role of Accelerated Burnup Irradiation Testing in Support of Accelerated Fuel Qualification

Accelerated fuel qualification has gained attention as a means to reduce the time needed to realize new nuclear fuel concepts and expand the operating windows of existing fuel forms. A key component of this approach is accelerated burnup irradiation testing. Although the concept of accelerated burnup has been familiar to the community for many decades, the specifics about how the increasing fission rate may be used as a qualification tool have not yet been elucidated. The present work provides a vision of how accelerated fission rate testing can enable accelerated fuel qualification. Technology readiness levels (TRLs) are reintroduced to demarcate the stages of traditional fuel qualification, and accelerated fuel qualification is presented in this context. The critical steps needed to achieve each TRL are reframed within the context of modern nuclear materials research and development, as revolutionary fuel concepts are more common than previous eras. The practical impacts of accelerated fuel qualification approaches as applied to contemporary fuel qualification efforts are illustrated. Examples are given to illustrate how accelerated burnup irradiations are being used currently and could be applied in the future to support qualification and licensure. Finally, outstanding challenges in the application of accelerated burnup methods to nuclear fuel qualification are summarized, with priority placed on understanding how fission rate impacts diffusion, microstructure evolution, and other critical mechanisms that dictate fuel performance.

Accelerated fuel qualification↗