Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

PIPS-2025: an updated practical pressure scale for the large-volume presses

In 1997, AIRAPT recommended a set of room-temperature pressure reference points (PRPs) for the large-volume press (LVP) community, known as the Practical International Pressure Scale (PIPS-97). With recent AIRAPT-recommended ruby scale Ruby2020 for diamond-anvil cell (DAC) experiments, it is now necessary to re-examine PIPS-97 for consistency with the DAC pressure scale. Here, we reconstruct equations of state (EOSs) for NaCl and Au that are explicitly tied to Ruby2020 and recalculate the PRPs using these EOSs. The revised PRP values are given. GaAs is removed from the PRP list because of the complexity of its phase transitions. The ZnS value, although retained, requires further investigation. Overall, the revised pressures are systematically higher than PIPS-97 by up to 4% at 35 GPa. We propose that this updated set of PRPs, referred to as PIPS-2025, be adopted for LVP experiments to improve pressure consistency between the LVP and DAC communities.

Large volume press↗
DOE OSTI2026

Simultaneous x-ray diffraction measurements of nine pressure calibrants to 140 GPa

Accurate pressure calibration is fundamental to quantitative high-pressure science, yet inconsistencies among widely used secondary pressure scales persist. In this work, we report simultaneous synchrotron x-ray diffraction meatogether in diamond anvil cells to 140 GPa. This simultaneous-measurement strategy minimizes transitive errors and run-to-run inconsistencies inherent to paired-measurement approaches, yielding direct experimental volume-volume (V-V) relations among the calibrants. These V-V relations link the compression state of each phase to that of every other phase measured in the same experiment. By anchoring these V-V relations to the reduced 300 K equation of state (EOS) of copper derived from ramp-compression measurements, we derive an internally consistent set of Cu-referenced pressure scales via Vinet EOS fits. Because the primary experimental result is the V-V dataset, it provides an EOS-independent constraint that can be rereferenced if primary standards are revised. The dataset further enables a direct experimental cross-check of consistency between the adopted reduced 300 K Cu EOS and the corresponding reduced 300 K ramp-derived EOSs for Pt, Au, Ta, and hcp-Fe under a fixed V-V constraint. The residuals quantify small, material-dependent mismatches between each phase EOS and the Cu reference EOS.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

The structure of high-Mg alkali-bearing aluminosilicate glasses investigated in situ at ambient and high pressure by multi-angle energy dispersive X-ray diffraction and infrared microspectroscopy

The structural properties of synthetic high-Mg alkali-bearing aluminosilicate glasses analogues of natural picritic-to-komatiitic magmas were investigated in situ by multiangle energy dispersive X-ray diffraction at 2.1 GPa and ambient pressure and by Fourier Transform infrared spectroscopy up to 5.4 GPa in a cycle of compression and decompression experiments. Our results show that the intermediate range ordering of the glass structure at 2.1 GPa is 3.14 Å, increasing to 3.19 Å when decompressed. The local structure shows T-O lengths of 1.66 Å (2.1 GPa) and 1.65 Å (ambient pressure), T-T distances of 3.19 Å at high pressure, which lengthen to 3.21 Å at ambient pressure, causing the T-O-T angle of 147° determined at 2.1 GPa to widen to 154° upon decompression. The deconvoluted infrared spectra result in the presence of Q 1 , Q 2 , Q 3 populations in the aluminosilicate spectral region, whose proportions remain relatively unchanged up to 5.4 GPa. The structural response of the investigated glasses to cold-compression does not involve changes in polymerization, but rather a shrinking and compaction of the structure as evidenced by the Qn species shifting to higher wavenumbers as a function of pressure. The structural properties determined from X-ray diffraction for this glass composition are discussed together with those of glasses emerging from previous studies to highlight a compositional dependence mainly dictated by the amount of SiO 2 and Al 2 O 3 .

glass structure↗
DOE OSTI2024

Pressure stability in explicitly coupled simulations of poromechanics with application to CO 2 sequestration

We study in detail the pressure stabilizing effects of the non-iterated fixed-stress splitting in poromechanical problems which are nearly undrained and incompressible. When applied in conjunction with a spatial discretization which does not satisfy the discrete inf–sup condition, namely a mixed piecewise linear–piecewise constant spatial discretization, the explicit fixed-stress scheme can have a pressure stabilizing effect in transient problems. This effect disappears, however, upon time step refinement or the attainment of steady state. The interpretation of the scheme as an Augmented Lagrangian method similar to Uzawa iteration for incompressible flow helps explain these results. Moreover, due to the slowly evolving solution within undrained seal regions, we show that the explicit fixed-stress scheme requires very large time steps to reveal its pressure stabilizing effect in examples of geologic CO 2 sequestration. We note that large time steps can result in large errors in drained regions, such as the aquifer or reservoir regions of these examples, and can prevent convergence of nonlinear solvers in the case of multiphase flows, which can make the explicit scheme an unreliable source of pressure stabilization. We conclude by demonstrating that pressure jump stabilization is as effective in the explicit fixed-stress setting as in the fully implicit setting for undrained problems, while maintaining the stability and convergence of the fixed-stress split for drained problems.

58 GEOSCIENCES↗
DOE OSTI2025

Two-dimensional burn velocity and analysis of burn products of nitromethane at high pressure

We have studied the laser-initiated deflagration of nitromethane (CH 3 NO 2 ) under high static pressure in the diamond anvil cell. Time-resolved images of the deflagrations have been obtained using intensified CCDs (ICCD). In contrast with previous work, we rely on spontaneous emission from the reaction, rather than changes in the speckle pattern produced by artificial illumination of the sample. Furthermore, as opposed to the 1D records obtained previously with streak cameras, ICCDs permit imaging of the burn in two dimensions providing the ability to directly observe anisotropic deflagration behavior. Here, we report several examples of this behavior and discuss its possible origins. We have also investigated the products of the reaction using Raman spectroscopy. At pressures below 25 GPa, the burn product is observed to be opaque and has a Raman spectrum consistent with a carbonaceous soot. At pressures above 25 GPa, the burn product is observed to be transparent (consistent with earlier reports) and its Raman spectrum reveals the presence of molecular N 2 and a nitrogen-carbonate species. The latter species can be recovered to ambient pressure and has a Raman spectrum consistent with ammonium carbonate or ammonium bicarbonate. To aid interpretation of the Raman spectra, measurements have also been made on the isotopologues CH 3 15 NO 2 and 13 CH 3 NO 2 . This work establishes the importance of advanced time-resolved imaging to reveal the details of deflagration under high pressure and further advances our understanding of the corresponding chemistry.

Deflagration↗
DOE OSTI2024

Dynamics of hydrogen–ammonia–natural gas lean-premixed high-pressure flames

The influence of fuel composition on self-excited combustion instabilities in a high-pressure combustor operated with ammonia, hydrogen, and natural gas fuels is characterized with high-frequency pressure measurements and imaging of the flame structure. A micromix multi-stage injector with 19 elements is used to introduce the fuel blend premixed with heated air into an optically accessible combustor operated at ~1.1 MPa. As hydrogen is substituted for natural gas, longitudinal thermoacoustic instabilities are observed in the combustor with pressure fluctuation amplitudes as large as 8% of the mean chamber value. In the absence of natural gas, limit-cycle instability magnitude is largely insensitive to ammonia addition. However, fuel compositions with > 20% natural gas result in positive correlation between instability amplitude and ammonia concentration. Spatial distribution of heat release in the combustor evaluated from OH* chemiluminescence imaging reveals axial growth in the regions of heat release fluctuation as hydrogen decreases, thus correlating flame length to instability amplitude. Distinct transitions from the first harmonic of the fundamental longitudinal acoustic mode (~1100 Hz) to the fundamental mode (~550 Hz) are observed with root mean square pressure fluctuations exceeding 7% of the mean chamber value. Here, these cases correspond to hydrogen mole fractions ≤ 50%. Analysis of the phase relationship between pressure fluctuations upstream and downstream of the flame zone indicates acoustic coupling of the injector as a key contributor to instability growth.

03 NATURAL GAS↗
DOE OSTI2025

Structure and Superconductivity of Hydrogenated TiZr Alloys Under High Pressure

The effects of pressure on the structure and electrical transport properties, including electrical resistance and critical magnetic field values for superconductivity in pristine and hydrogenated TiZr alloys, were investigated. As pressure increased from ambient to 55 GPa, the structure of the pristine TiZr alloys transformed from hcp to bcc via an intermediate ω phase. The superconducting transition temperature (T c ) significantly increased from 1.76 K at ambient pressure to 15.5 K at 52.2 GPa, accompanied by an extrapolated upper critical field of 24.5 T at T = 0 K. In contrast, the hydrogenated samples exhibited substantially lower T c values compared to the pristine ones, with a T c of 4.6 K at 50.5 GPa and an extrapolated upper critical field of 1.8 T at T = 0 K. Upon decompression, the superconductivity in the hydrogenated sample persisted down to 25 GPa, disappearing when the pressure was reduced to 19 GPa. Synchrotron X-ray diffractions (XRD) analysis revealed the formation of three hydrides: I4/mmm-(Ti, Zr)H 2 , P6 3 /mmc-(Ti, Zr)H 3 , and I4̅3d-(Ti,Zr) 4 H 15 . Finally, by combining XRD and electrical resistance data, we tentatively propose that the P6 3 /mmc-(Ti, Zr)H 3 predominantly induces superconductivity. In contrast to superhydrides, where electron–phonon interactions increase the superconducting temperature at high pressure, hydrogen atoms in hcp-(Ti, Zr)H 3 reduce T c .

36 MATERIALS SCIENCE↗
DOE OSTI2026

Pressurized Gas-Driven Elemental Redistribution Enables Ultrastable PtNi Catalysts for Heavy-Duty Vehicles

Gas-driven element redistribution, characterized by the preferential enrichment of one element at the surface relative to the bulk, is frequently observed in multicomponent alloys. Using L1 0 -ordered PtNi as a model system, we reveal that gas pressure plays a critical role in governing adsorption-driven surface composition during annealing in reducing gases: low pressure favors Pt surface segregation, while high pressure facilitates Ni surface enrichment. In this study, we developed a high-pressure nitriding (HPN) strategy that modulates the surface structure and composition of PtNi catalysts. The resulting HPN-PtNi exhibits enhanced performance and durability in membrane electrode assemblies for heavy-duty fuel cell applications, maintaining a high current density of 1.19 A cm −2 at 0.7 V after 90,000 voltage cycles. Through a combination of experimental and theoretical analyses, we reveal that the HPN process forms additional stabilizing Ni−N bonds and induces elemental redistribution with Ni surface enrichment and a Ni-deficient Pt subsurface. These modifications alter the atomic coordination environment of the ordered PtNi phase. This work presents a generalizable strategy to design robust and high-performing Pt-based catalysts by controlling gas-pressure-driven elemental redistribution and dopant incorporation.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2025

Pressure induced irreversible phase transformation in an ordered high-entropy alloy

We report on a pressure induced irreversible phase transformation in an ordered eutectic high-entropy alloy (EHEA) AlCoCrFeNi2.1. The suction cast sample was synthesized by arc melting of raw elements resulting in an ordered B2 and FCC phase mixture for eutectic AlCoCrFeNi2.1 alloy. This phase mixture was confirmed by transmission electron microscopy (TEM) where superlattice reflections corresponding to ordered B2 phase were observed while the FCC phase remains disordered. The B2 phase was observed to be enriched in Nickel and Aluminum while the surrounding FCC phase is enriched in Fe, Cr and Co. The suction-cast EHEA sample was studied by X-ray diffraction under high pressure in a diamond anvil cell with platinum pressure marker to 73 GPa at ambient temperature. The B2 to FCC phase transformation is completed by 3 GPa in sharp contrast to BCC to FCC phase transition of 21 GPa in additively manufactured EHEA samples. The X-ray diffraction and TEM studies of pressure recovered samples show presence of only FCC grains without any specific orientation with respect to starting sample. These results are consistent with molecular dynamics simulations that the presence of B2 phase aids in the formation of the B2 to FCC phase transition under high pressures.

36 MATERIALS SCIENCE↗
DOE OSTI2025

X-ray diffraction strains in laser-ablated aluminum, nickel, sodium, and invar: Pressures to 475 GPa

Dynamically compressed materials in longitudinal waves are described by two physical models: hydrostatic pressure, with equal, normal, principal stresses or material uniaxially strained in the wave propagation direction. These models are disparate, so experimental comparisons and evaluations are important. Polycrystalline material in a state of hydrostatic pressure will have no eccentricity of x-ray-diffracted Debye–Scherrer rings. A general three-dimensional solution of Bragg diffracted x rays based on principal crystallographic strains in the compression wave was found. The distortion of x-ray diffraction beams has been used for strain measurements; the analysis developed incorporates a strained reciprocal lattice and the incident x-ray beam. Strain-distorted Polanyi surfaces form an annulus of compression with an ellipsoid of revolution in reciprocal space, which is intersected by Ewald's sphere for Bragg diffraction. The in situ measurements for strain describe nanosecond diffraction evaluated using two planes, (hkl) and (h′k′l′), both in the same crystallographic phase. Diffraction from Al, Ni, Na, and Invar quantifies the compression axial strains in these materials: The compression axial ratios are 0.65, 1.05, 0.88, and 1.58 at pressures of 291, 402, 409, and 367 GPa for the respective materials. Crystal structure transformations with homogeneous pressurized stresses, mandating equal normal strains, should not be anticipated to agree with heterogeneous, uniaxially strained, and sheared crystalline phases. Measurements support in-plane strains increasing with pressure, p , in fcc and hcp aluminum as ε 22 = −0.21 p /TPa.

Alloys↗
DOE OSTI2025

Microfluidic cells for the 1–10 2 MPa pressure range

Thin membrane-delimited fluid cells supporting up to 1 at (0.1 MPa) of pressure are well known and commercially available for use in vacuum chambers of electron, photon, or various particle beam microscopies or spectroscopies. Hereby, we report on the development of fluid cells capable of working at 1–10 MPa, extending the analysis domain for investigating chemical, biochemical, or physical processes at pressures of interest in chemical synthesis, underwater biochemistry studies or underground geology. We explored ways to optimize cell membranes to better resist pressure beyond simply increasing the thickness or decreasing the size of the membranes, using finite element analysis and experimental validation via membrane bulging experiments and failure statistics. Fluid cell prototypes were fabricated using ∼75 nm-thick SiN x membranes, engineered to withstand 4.7 MPa (average value), compared to regular (un-engineered) membranes withstanding only 3.4 MPa (average value). The fluid cell prototypes include eight microchannels for feeding/evacuating the fluids and applying pressure into micro-reaction chambers, two electrodes for electrochemical or conduction measurements in the sample, and a possible pressure or temperature sensor, customizable for specific experiments.

hi-pressure↗
DOE OSTI2024

Suppression of metal-to-insulator transition and stabilization of superconductivity by pressure in Re 3 Ge 7

The effect of pressure on the low-temperature states of the Re 3 ⁡Ge 7 is investigated by both electrical and Hall resistance and magnetization measurements. At ambient pressure, the temperature-dependent resistance of Re 3 ⁡Ge 7 behaves quasilinearly from room temperature down to 60 K, then undergoes a two-step metal-to-insulator transition (MIT) at temperatures T 1 =59.4K and T 2 =58.7K, which may be related to a structural phase transition or occurrence of charge-density wave ordering. Upon applying pressure, the two-step (T 1 ,T 2 ) MIT splits into three steps (T 1 ,T 2 . and T 3 ) above 1 GPa, and all traces of MITs are fully suppressed by ~8 GPa. Subsequently, the onset of bulk superconductivity (SC) occurs between 10.8 and 12.2 GPa and persists to our highest pressure of 26.8 GPa. At 12.2 GPa the superconducting transition temperature, T c , and upper critical field, H c ⁢2 reach the maximum of T c (onset) ~5.9 K and H c ⁢2 (1.8 K) ~14 kOe. Finally, our results not only present the observation of SC under high pressure in Re 3 ⁡Ge 7 but also delineate the interplay between SC and other competing electronic states by creating a T-p phase diagram for this potentially topologically nontrivial system Re 3 ⁡Ge 7 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Superconducting dome and structural changes in LaRu 3 ⁢Si 2 under pressure

LaRu 3 ⁢Si 2 is of current research interest as a kagome metal with a superconducting transition temperature, 𝑇 𝑐 ∼7 K, and higher-temperature charge density wave orders. Here we report on electrical transport and x-ray diffraction measurements on LaRu 3 ⁢Si 2 under pressure up to 65 GPa and 35 GPa, respectively. The superconducting transition temperature 𝑇 𝑐 first gets slightly enhanced and reaches a maximum ∼8.7 K at ∼8.5 GPa. With further applied pressure, 𝑇 𝑐 is initially gradually suppressed, then more rapidly suppressed, followed by gradual suppression, revealing a superconducting dome. Two possible pressure-induced structural phase transitions are also observed at room temperature, from the original hexagonal phase to another hexagonal structure above ∼11.5 GPa, and further to a structure with lower symmetry above ∼23.5 GPa. These transition pressures roughly correlate with features found in our pressure-dependent transport data.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Pressure dependence of intermediate-range order and elastic properties of glassy Baltic amber

Amber is a unique example of a fragile glass that has been extensively aged below its glass transition temperature, thus reaching a state that is not accessible under normal experimental conditions. In this paper, we studied the medium-range order of Baltic amber by x-ray diffraction (XRD) at high pressures. The pressure dependences of the low-angle XRD intensity between 0 and 5 Å -1 were measured from 0 to 7.3 GPa by the energy-dispersive XRD. The first diffraction peak at 1.1 Å -1 and ambient pressure has a doublet structure consisting of the first sharp diffraction peak (FSDP) at 1.05 Å -1 and the second feature at 1.40 Å -1 . The peak position and the width of the FSDP increase as the pressure increases, while the intensity of the FSDP decreases. Below P 0 = 2.4 GPa, the rapid increase of the FSDP peak position was observed, while above P 0 , the gradual increase was observed. Below P 0 , voids and holes in a relatively low-density state are suppressed, whereas above P 0 , the suppression becomes mild. Such a change suggests the crossover from the low- to high-density state at P 0 . There is a close correlation between the pressure dependence of XRD and previously reported sound velocity results. The correlation between the mean-square fluctuation of the shear modulus on the nanometer scale and fragility in amber and other glass formers is also discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Tunneling Spectroscopy at Megabar Pressures: Determination of the Superconducting Gap in Sulfur

The recent discovery of high-temperature, high-pressure superconductors, such as hydrides and nickelates, has opened exciting avenues in studying high-temperature superconductivity. The primary superconducting properties of these materials are well characterized by measuring various electrical and magnetic properties, despite the challenges posed by the high-pressure environment. Experimental microscopic insight into the pairing mechanism of these superconductors is even more challenging, due to the lack of direct probes of the superconducting gap structures at high pressure conditions. Here, we have developed a planar tunnel junction technique for diamond anvil cells and present ground-breaking tunneling spectroscopy measurements at megabar pressures. We determined the superconducting gap of elemental sulfur at 160 GPa, a key constituent of the high-temperature superconductor H 3 S . High quality tunneling spectra indicate that β -Po phase sulfur is a type II superconductor with a single s -wave gap with a gap value 2 Δ ( 0 ) = 5.6 meV . This technique is compatible with superconducting compounds synthesized in diamond anvil cells and provides insight into the pairing mechanism in novel superconductors under high-pressure conditions. Published by the American Physical Society 2024

36 MATERIALS SCIENCE↗
DOE OSTI2026

Pore-Scale Study on the Positive Feedback Between Stress and Porosity Caused by Pressure Solution in Porous Media

Pressure solution is an important process in the evolution of sedimentary rocks, which provide storage space for most of our petroleum resources. It directly influences the generation, migration, and storage of petroleum fluids in subsurface sedimentary rocks. Here, in this paper, we develop a pore-scale, mechanochemical model to demonstrate a possible positive feedback between the local porosity and pore surface stress, in which a higher local porosity causes a higher local pore surface stress, thus enhancing pressure solution and consequently further increasing the local porosity. Pore surface stress represents stress on a solid grain adjacent to a pore. Specifically, the pore-scale, mechanochemical model directly simulates the stress distribution over solid and pore surfaces using a finite element model. The dissolution of solids at the solid-pore interfaces under a far-from-equilibrium condition is simulated using a first-order kinetics model that accounts for the local stress distribution. The updated pore geometry, caused by pore surface dissolution, is then used in the stress simulation in the next numerical iteration. Two types of porous media, the Oriskany sandstone and an artificial porous medium with spherical pores, were tested in the mechanochemical simulation. The positive stress-porosity feedback during pressure solution was observed in both samples. In addition, the model quantitatively illustrated the distribution of local mineral dissolution rates on all pore surfaces, as well as its relation to the effective mineral dissolution rate of the entire sample. Based on the comparison between the two porous media, the local mineral dissolution was regulated by pore space distribution, geometry, and coalescence during pressure solution. This work is the first that uses direct, pore-scale numerical simulation to demonstrate the positive stress-porosity feedback during pressure solution, which has the potential to advance the understanding of the mechanical-chemical (MC) coupling in many geological processes that are relevant to subsurface energy systems, such as the recovery of petroleum hydrocarbons and geothermal energy.

CT scanning↗
DOE OSTI1991

Pressure Safety Training (Rev. 8)

This is the workbook for the Pressure Safety Training Course. It is intended as a reference manual and guide for all work with pressurized liquids or gases. This workbook contains basic references to make work with pressure safer. It is intended to supplement classroom instruction, rather than serve as a definitive text on pressure. Earlier versions of the manual were intended specifically for training at Lawrence Livermore National Laboratory. This revision is a generic version intended for training at all DOE facilities. The information in the Standards chapter is from the LLNL Health and Safety Manual. It is included here as a convenient reference and guide for developing similar standards at your own facility.

42 ENGINEERING↗
DOE OSTI2026

Reducing the Strain Required for Ambient‐Pressure Superconductivity in Ruddlesden‐Popper Bilayer Nickelates

ABSTRACT The discovery of high‐temperature superconductivity in pressurized bulk Ruddlesden‐Popper (RP) bilayer nickelates has prompted the conjecture that epitaxial compressive strain might mimic essential aspects of hydrostatic pressure. The realization of superconductivity in films on SrLaAlO 4 (001) (SLAO) supports this correspondence, yet it remains unclear whether the pressure–temperature phase diagram of RP bilayer nickelates can be systematically mapped (and studied at ambient pressure) as a function of epitaxial strain. To this end, experimental access near the elusive edge of the superconducting phase boundary would provide invaluable insight into the nature of the superconducting state and the ground state from which it emerges. Here we report superconducting RP bilayer nickelates grown on LaAlO 3 (001) (LAO), where the compressive strain required for ambient‐pressure superconductivity is nearly halved to −1.2%. These films exhibit a superconducting onset above 10 K and reach zero resistance at 3 K, with normal‐state transport properties differing from those of films grown on SLAO. Our comparative study shows that strain–rather than interfacial structure is the primary factor governing the superconductivity and normal‐state properties. This work offers a new opportunity to probe emergent phenomena near the superconducting phase boundary in the strain–temperature phase diagram of RP bilayer nickelates.

Tarn, Yaoju [Department of Applied Physics Stanfor↗