Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Optical Storage Devices”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS2008

Phase Matching of Diverse Modes in a WGM Resonator

Phase matching of diverse electromagnetic modes (specifically, coexisting optical and microwave modes) in a whispering-gallery-mode (WGM) resonator has been predicted theoretically and verified experimentally. Such phase matching is necessary for storage of microwave/terahertz and optical electromagnetic energy in the same resonator, as needed for exploitation of nonlinear optical phenomena. WGM resonators are used in research on nonlinear optical phenomena at low optical intensities and as a basis for design and fabrication of novel optical devices. Examples of nonlinear optical phenomena recently demonstrated in WGM resonators include low-threshold Raman lasing, optomechanical oscillations, frequency doubling, and hyperparametric oscillations. The present findings regarding phase matching were made in research on low-threshold, strongly nondegenerate parametric oscillations in lithium niobate WGM resonators. The principle of operation of such an oscillator is rooted in two previously observed phenomena: (1) stimulated Raman scattering by polaritons in lithium niobate and (2) phase matching of nonlinear optical processes via geometrical confinement of light. The oscillator is partly similar to terahertz oscillators based on lithium niobate crystals, the key difference being that a novel geometrical configuration of this oscillator supports oscillation in the regime. The high resonance quality factors (Q values) typical of WGM resonators make it possible to achieve oscillation at a threshold signal level much lower than that in a non-WGM-resonator lithium niobate crystal.

Savchenkov, Anatoliy↗
NASA NTRS2010

Enhanced Microbial Detection Capabilities by a Rapid Portable Instrument

We present data describing a progression of continuing technology development - from expanding the detection capabilities of the current PTS unit to re-outfitting the instrument with a protein microarray increasing the number of detectable compounds. To illustrate the adaptability of the cartridge format, on-orbit operations data from the ISS demonstrate the detection of the fungal cell wall compound beta-glucan using applicable LOCAD-PTS cartridges. LOCAD-PTS is a handheld device consisting of a spectrophotometer, an onboard pumping mechanism, and data storage capabilities. A suite of interchangeable cartridges lined with four distinct capillaries allow a hydrated sample to mix with necessary reagents in the channels before being pumped to the optical well for spectrophotometric analysis. The reagents housed in one type of cartridge trigger a reaction based on the Limulus Amebocyte Lysate (LAL) assay, which results in the release of paranitroaniline dye. The dye is measured using a 395 nm filter. The LAL assay detects the Gram-negative bacterial cell wall molecule, endotoxin or lipopolysaccharide (LPS). The more dye released, the greater the concentration of endotoxin in the sample. Sampling, quantitative analysis, and data retrieval require less than 20 minutes. This is significantly faster than standard culture-based methods, which require at least a 24 hour incubation period.Using modified cartridges, we demonstrate the detection of Gram negative bacteria with protein microarray technology. Additionally, we provide data from multiple field tests where both standard and advanced PTS technologies were used. These tests investigate the transfer of target microbial molecules from one surface to another. Collectively, these data demonstrate that the new cartridges expand the number of compounds detected by LOCAD-PTS, while maintaining the rapid, in situ analysis characteristic of the instrument. The unit provides relevant data for verifying sterile sample collection protocols, which are critical for conducting accurate scientific experiments during future missions to the Moon and Mars.

Morris, Heather↗
NASA NTRS2013

NASA Tech Briefs, July 2013

Dielectrophoresis-Based Particle Sensor Using Nanoelectrode Arrays; Multi-Dimensional Damage Detection for Surfaces and Structures; ULTRA: Underwater Localization for Transit and Reconnaissance Autonomy; Autonomous Cryogenic Leak Detector for Improving Launch Site Operations; Submillimeter Planetary Atmospheric Chemistry Exploration Sounder; Method for Reduction of Silver Biocide Plating on Metal Surfaces; Silicon Micromachined Microlens Array for THz Antennas; Forward-Looking IED Detector Ground Penetrating Radar; Fully Printed, Flexible, Phased Array Antenna for Lunar Surface Communication, Battery Charge Equalizer with Transformer Array; An Efficient, Highly Flexible Multi-Channel Digital Downconverter Architecture; Dimmable Electronic Ballast for a Gas Discharge Lamp; Conductive Carbon Nanotube Inks for Use with Desktop Inkjet Printing Technology; Enhanced Schapery Theory Software Development for Modeling Failure of Fiber-Reinforced Laminates; High-Performance, Low-Temperature-Operating, Long-Lifetime Aerospace Lubricants; Carbon Nanotube Microarrays Grown on Nanoflake Substrates; Differential Muon Tomography to Continuously Monitor Changes in the Composition of Subsurface Fluids; Microgravity Drill and Anchor System; 20 Granular Media-Based Tunable Passive Vibration Suppressor; 21 Miga Aero Actuator and 2D Machined Mechanical Binary Latch; Micro-XRF for In Situ Geological Exploration of Other Planets; Hydrogen-Enhanced Lunar Oxygen Extraction and Storage Using Only Solar Power; Uplift of Ionospheric Oxygen Ions During Extreme Magnetic Storms; Miniaturized, High-Speed, Modulated X-Ray Source; Hollow-Fiber Spacesuit Water Membrane Evaporator 25 High-Power Single-Mode 2.65-micrometers InGaAsSb/AlInGaAsSb Diode Lasers; Optical Device for Converting a Laser Beam Into Two Co-aligned but Oppositely Directed Beams; A Hybrid Fiber/Solid-State Regenerative Amplifier with Tunable Pulse Widths for Satellite Laser Ranging; X-Ray Diffractive Optics; SynGenics Optimization System (SynOptSys); 29 CFD Script for Rapid TPS Damage Assessment; radEq Add-On Module for CFD Solver Loci-CHEM; Science Opportunity Analyzer (SOA) Version 8; 30 Autonomous Byte Stream Randomizer; Distributed Engine Control Empirical/Analytical Verification Tools; Dynamic Server-Based KML Code Generator Method for Level-of-Detail Traversal of Geospatial Data; Automated Planning of Science Products Based on Nadir Overflights and Alerts for Onboard and Ground Processing; Linked Autonomous Interplanetary Satellite Orbit Navigation; Risk-Constrained Dynamic Programming for Optimal Mars Entry, Descent, and Landing; Scheduling Operations for Massive Heterogeneous Clusters; Deepak Condenser Model (DeCoM); Flight Software Math Library; Recirculating 1-K-Pot for Pulse-Tube Cryostats; 35 Method for Processing Lunar Regolith Using Microwaves; Wells for In Situ Extraction of Volatiles from Regolith (WIEVR); and Estimating the Backup Reaction Wheel Orientation Using Reaction Wheel Spin Rates Flight Telemetry from a Spacecraft.

Source record↗
NASA NTRS1980

Studies of laser and laser devices

The generation of tunable, infrared, and ultraviolet light, and the control of this light by mode-locking and modulation techniques are discussed. Particular emphasis is given to energy storage and extraction using atomic levels, the development of a tunable narrowband vacuum ultraviolet light source, and to the generation and applications of ultrashort optical pulses.

Harris, S. E.↗
NASA NTRS1981

Technology and future ground processing systems

Land-observing satellites with multiple thematic mappers will produce data at rates of 100 to 300 Mbps. When coupled with a high daily scene production rate, these rates will require new approaches to ground processing. Consideration is given here to future downlink rates and data volumes, and requirements peculiar to the future user community are discussed. The advanced technologies required to attain an operational system in the years 1985-1990 are considered, together with advances foreseen in communications, mass storage, bulk memories, and data processing. Using advanced devices, a centralized data processing system capable of handling the 100 Mbps data rate is described. New approaches, among them a parallel pipelined calibration front-end, real-time browse image production, a high bandwidth optical disk archive, regional image broadcast and massively parallel product production, are considered. A distributed system capable of handling the 300 Mbps data rate is then described. Designs for a hub system and a regional processing center are presented.

Wood, B. J.↗
DOE OSTI2026

Multiscale Characterization of Electrode-Induced Degradation in Perovskite Solar Cells

The stability of metal-halide-perovskite (MHP) solar cells must be understood and improved for the commercial viability of MHP technologies. Here, we apply multiscale characterization methods to study degradation modes, specifically electrode corrosion, for p-i-n MHP partial device stacks and full devices that are stored in the dark under an inert atmosphere. Our multiscale characterization approaches include full-device electro-optical performance using current-voltage (JV) curves and spatial imaging with electroluminescence (EL) and photoluminescence (PL). We further correlate interface properties using cross-sectional Kelvin probe force microscopy, which maps the nanoscale electric field properties, and electron microscopy, which demonstrates structural and chemical features. Devices stored as a full device stack degrade primarily by metal (Ag) electrode diffusion into the absorber, with formation of AgI byproducts and Ag accumulation near the indium tin oxide (ITO) contact. This causes decomposition of the perovskite absorber domains, loss of the potential drop at the electron transport layer (ETL)/perovskite interface near the metal contact, and increased equivalent resistance at the perovskite/hole transport layer (HTL) interface near the ITO contact. The devices stored without metal show a different degradation pathway dominated by corrosion of the ITO, creating voids at the ITO electrode surface with diffusion of In and Sn into the absorber. We conclude that metal electrode-induced degradation is the most severe degradation pathway under dark storage, but that ITO corrosion and absorber instability must also be mitigated. We further demonstrate mitigation of these degradation pathways by changes to the device stack, including a SnO x blocking layer at the ETL side and replacing ITO with FTO at the HTL side. These results provide a useful demonstration of specific dark degradation pathways at each electrode interface, as well as a unique multiscale example that links degradation of chemical, structural, and electrical interface properties to the full-device electro-optical characteristics.

14 SOLAR ENERGY↗
DOE OSTI2022

Tunable and reconfigurable atomically thin heterostructures

Heterocrystals of metal dichalcogenides and Bi 2 S 3 , Bi 2 Se 3 or Bi 2 Te 3 are presented, in which the metal dichalcogenides and Bi 2 S 3 , Bi 2 Se 3 or Bi 2 Te 3 do not largely retain their independent properties. These heterocrystals exhibit electronic and optical changes, which make them attractive for beyond-silicon electronics and optoelectronics. Particularly, these heterocrystals can be re-configured in a manner that allows bit writing and pattern drawing. Embodiments of these heterocrystals, methods of forming these heterocrystals, methods of reconfiguring the heterocrystals, information storage devices, optoelectronic circuits and photonic crystals are presented.

Vargas, Anthony↗
DOE OSTI2022

Watching Polarons Move in the Energy and Frequency Domains Using Color Impedance Spectroscopy

The hybrid electronic–ionic transport property of π-conjugated polymers enables new (opto)electrochemical device constructs for energy conversion and storage and biosensing applications. One major challenge is separating the energy and frequency dependence of Faradaic events–those involving charge transfer and the redox processes of the conjugated backbone–from the non-Faradaic components, such as ionic motion. Herein, we combine optical spectroscopy with electrochemical impedance spectroscopy (EIS) to resolve the frequency response of ionic–electronic coupling as a function of electrochemical doping potential. First, using EIS, we identify two different frequency regimes resulting in potential-dependent capacitive elements on the order of ~10 μF/cm 2 in a high-frequency regime and ~50–150 μF/cm 2 in a low-frequency regime. Given the larger magnitude and greater potential dependence, we posit that polaronic motion is more likely to occur at low frequencies (<1 kHz) and overlaps with ionic motion. The use of color impedance spectroscopy (CIS) enables observation of polaronic motion with frequency modulation. We observe that higher doping potentials show a greater motion of polarons above the DC-bias baseline concentration for onset in electrochemical doping, but all potentials considered demonstrate a critical frequency at which the polaronic motion is “frozen” (~40 Hz). Furthermore, this critical information obtained from CIS in highly dielectric environments offers a unique figure of merit for future studies on electronic–ionic coupling by which to compare across polymer/electrolyte interfaces, including the role of a charge-supporting electrolyte, a solvent, and alternative Faradaic processes (e.g., electrocatalysis).

36 MATERIALS SCIENCE↗
DOE OSTI2020

Vacuum-Free, All-Solution, and All-Air Processed Organic Photovoltaics with over 11% Efficiency and Promoted Stability Using Layer-by-Layer Codoped Polymeric Electrodes

Nonfullerene organic photovoltaics (OPVs) have achieved a breakthrough in pushing the efficiency beyond 15%. Although this sheds light on OPV commercialization, the high cost associated with the scalable device fabrications remains a giant challenge. Herein, a vacuum-free, all-solution and all-air processed OPV is reported that yields 11.12% efficiency with a fill factor of 0.725, due to the usages of high-merit polymeric electrodes and modified active blends. The design principle toward the high-merit electrodes is to induce heavy acid doping into the matrices for a raised carrier concentration and mobility, make a large removal of insulating components in the whole matrices rather than surfaces, and restrain the formation of large-domain aggregates. A unique layer-by-layer doping is developed to enable the polymeric electrodes with record-high trade-offs between optical transmittance and electrical conductivity. Moreover, solvent vapor annealing is proposed to boost device efficiency and it has the advantages of finely adjusting the active blend morphology and raising the electron mobility. The resulting devices are highly efficient and most (≈91%) of the initial efficiency are maintained in 30 day storage. Finally, this work indicates bright future for making cost-effective all-solution processed OPVs in air.

14 SOLAR ENERGY↗
NASA NTRS2001

The Need for Optical Means as an Alternative for Electronic Computing

An increasing demand for faster computers is rapidly growing to encounter the fast growing rate of Internet, space communication, and robotic industry. Unfortunately, the Very Large Scale Integration technology is approaching its fundamental limits beyond which the device will be unreliable. Optical interconnections and optical integrated circuits are strongly believed to provide the way out of the extreme limitations imposed on the growth of speed and complexity of nowadays computations by conventional electronics. This paper demonstrates two ultra-fast, all-optical logic gates and a high-density storage medium, which are essential components in building the future optical computer.

Adbeldayem, Hossin↗
DOE OSTI2023

The Roadrunner Trap: A QSCOUT Device

The Roadrunner ion trap is a micro-fabricated surface-electrode ion trap based on silicon technology. This trap has one long linear section and a junction to allow for chain storage and reconfiguration. It uses a symmetric rf-rail design with segmented inner and outer control electrodes and independent control in the junction arms. The trap is fabricated on Sandia’s High Optical Access (HOA) platform to provide good optical access for tightly focused laser beams skimming the trap surface. It is packaged on our custom Bowtie-102 ceramic pin or land grid array packages using a 2.54 mm pitch for backside pins or pads. This trap also includes an rf sensing capacitive divider and tungsten wires for heating or temperature monitoring. The Roadrunner builds on the knowledge gained from previous surface traps fabricated at Sandia while improving ion control capabilities.

42 ENGINEERING↗
NASA NTRS1989

Optical processing for distributed sensors in control of flexible spacecraft

A recent potential of distributed image processing is discussed. Applications in the control of flexible spacecraft are emphasized. Devices are currently being developed at NASA and in universities and industries that allow the real-time processing of holographic images. Within 5 years, it is expected that, in real-time, one may add or subtract holographic images at optical accuracy. Images are stored and processed in crystal mediums. The accuracy of their storage and processing is dictated by the grating level of laser holograms. It is far greater than that achievable using current analog-to-digital, pixel oriented, image digitizing and computing techniques. Processors using image processing algebra can conceptually be designed to mechanize Fourier transforms, least square lattice filters, and other complex control system operations. Thus, actuator command inputs derived from complex control laws involving distributed holographic images can be generated by such an image processor. Plans are revealed for the development of a Conjugate Optics Processor for control of a flexible object.

Montgomery, Raymond C.↗
DOE OSTI2024

Light–Material Interactions Using Laser and Flash Sources for Energy Conversion and Storage Applications

Abstract This review provides a comprehensive overview of the progress in light–material interactions (LMIs), focusing on lasers and flash lights for energy conversion and storage applications. We discuss intricate LMI parameters such as light sources, interaction time, and fluence to elucidate their importance in material processing. In addition, this study covers various light-induced photothermal and photochemical processes ranging from melting, crystallization, and ablation to doping and synthesis, which are essential for developing energy materials and devices. Finally, we present extensive energy conversion and storage applications demonstrated by LMI technologies, including energy harvesters, sensors, capacitors, and batteries. Despite the several challenges associated with LMIs, such as complex mechanisms, and high-degrees of freedom, we believe that substantial contributions and potential for the commercialization of future energy systems can be achieved by advancing optical technologies through comprehensive academic research and multidisciplinary collaborations.

Materials Science↗
NASA NTRS2018

Role of a Chemist in Modern Industries: Design and Development of Nanoengineered Multifunctional Materials

During the past fifteen years significant investment has been made for the applications of nanotechnology in almost every aspect of life. Almost every area of research has projected improvements including biotechnology, bioinspired electronic, optical and radiological sensors, or a promise for the emergence of some novel device technologies. For such applications major focus has been placed on research nanoparticles, nanotubes nanorods and two-dimensional structures similar to that of graphene. Some near- term applications of nano- particles and nanowires have produced very promising results for better synthesis of energy storage materials, design of biologically active composites like apatites, laser host crystals, photodetectors and sensor materials for radiation detection. To achieve desired morphologies, nanomaterials can be utilized some organic melt and orient the grains by the directional solidification method. The organic treated materials produce different characteristics than coarsened oxide materials. The focus is also understanding the morphology and performance function in human organs that occur because of aging or disease, and responses to interventions. We annealed to determine the changes in morphologies and hence effect of aging. In this presentation, we will discuss correlation between the designed composition, micromorphology and the performance parameters of nanomaterials. To understand the mechanism of formation of nanoparticles, nanoboloids, fibers experimental details and observations on the of multinary compounds will be presented. These observations on the transition of nanomorphology can highlight the mechanism of the phase transition in some oxides and selenides.

Singh, N. B.↗
NASA NTRSDate not supplied

New Phase Change Materials for Active Photonics

Phase change materials or PCMs are truly remarkable compounds whose unique switchable properties have fueled an explosion of emerging applications in electronics and photonics. Nonetheless, if we discount their use in optical discs, PCMs’ immense application potential in photonics beyond data recording has only begun to unfold in the past decade. While the material requirements for optical or electronic data storage have been succinctly summarized as five key elements “writability, archival storage, erasability, readability, and cyclability” decades ago, these requirements are not universally relevant to the diverse set of photonic applications now being explored. It also comes as no surprise that existing PCMs, which have been heavily vetted for data storage, are not necessarily the optimal compositions for different use cases in optics and photonics. PCMs with their attributes custom-tailored for specific applications are therefore in demand as phase-change photonics continue to expand. Here we discuss the PCM selection and design strategies specifically for photonic applications as well as our recent work developing active integrated photonic devices and metasurface optics based on new PCMs tailored for photonics.

phase change materials↗
NASA NTRS2011

Local Leak Detection and Health Monitoring of Pressurized Tanks

An optical gas-detection sensor safely monitors pressurized systems (such as cryogenic tanks) and distribution systems for leaks. This sensor system is a fiber-coupled, solid optical body interferometer that allows for the miniaturized sensing element of the device to be placed in the smallest of recesses, and measures a wide range of gas species and densities (leaks). The deflection of the fringe pattern is detected and recorded to yield the time-varying gas density in the gap. This technology can be used by manufacturers or storage facilities with toxic, hazardous, or explosive gases. The approach is to monitor the change in the index of refraction associated with low-level gas leaks into a vacuum environment. The completion of this work will provide NASA with an enabling capability to detect gas system leaks in space, and to verify that pressurized systems are in a safe (i.e. non-leaking) condition during manned docking and transit operations. By recording the output of the sensor, a time-history of the leak can be constructed to indicate its severity. Project risk is mitigated by having several interferometric geometries and detection techniques available, each potentially leveraging hardware and lessons learned to enhance detectability.

Polzin, Kurt↗
NASA NTRS1993

Spacecraft optical disk recorder memory buffer control

This paper discusses the research completed under the NASA-ASEE summer faculty fellowship program. The project involves development of an Application Specific Integrated Circuit (ASIC) to be used as a Memory Buffer Controller (MBC) in the Spacecraft Optical Disk System (SODR). The SODR system has demanding capacity and data rate specifications requiring specialized electronics to meet processing demands. The system is being designed to support Gigabit transfer rates with Terabit storage capability. The complete SODR system is designed to exceed the capability of all existing mass storage systems today. The ASIC development for SODR consist of developing a 144 pin CMOS device to perform format conversion and data buffering. The final simulations of the MBC were completed during this summer's NASA-ASEE fellowship along with design preparations for fabrication to be performed by an ASIC manufacturer.

Hodson, Robert F.↗
DOE OSTI2022

Wavefront Preservation in Soft X-Ray Beamlines for the Advanced Light Source Upgrade

In the 4th generation of X-ray light sources, including Free-Electron Lasers (FEL) and Diffraction-Limited Storage Rings (DLSR), the emittance of the electron beam is small or negligible compared to the emittance of the photon beam produced by insertion devices, thus generating coherent beams of light. Over the next few years, several lightsource facilities will be built or upgraded to produce X-ray beams of unprecedented coherent flux. Delivering these exceptional beams to the sample chambers requires beamline optical systems that are designed to preserve the wavefront properties. Our goal in the Advanced Light Source upgrade project (ALS-U) is to create a new class of beamlines that reach diffraction-limited X-ray optical quality through tightly integrated, efficient optical systems, diagnostics, and adaptive mirrors, thus providing users with new scientific capabilities offered by coherent X-ray light interactions with matter. Herein we describe aspects of the beamlines’ design as they enter the project’s final design phase.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗