Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “OILS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

A model for droplet heating and evaporation of water-in-oil emulsified fuel

Water-in-oil (W/O) emulsified fuel is a promising alternative fuel by inducing flash boiling of water at high temperature that can improve the atomization of fuel spray. The heating and evaporation process of emulsified fuel droplet is affected by the diffusion and coalescence of small dispersed water droplets in oil during the heating. In this study, a model is developed for the droplet heating and evaporation of W/O emulsified fuel with these key physics considered. The diffusivity of dispersed water droplets in oil is calculated using the Stokes-Einstein equation. The deactivation temperature of surfactant is selected as a criterion for the water coalescence since the water coalescence is due to the deactivation of surfactant. The process of water coalescence is simplified that the dispersed water droplets coalesce into one single water sub-droplet at the center of the oil droplet instantly as the droplet temperature reaches the deactivation temperature of surfactant. The model is validated against experimental data of single droplet under different heating temperatures, surfactant concentrations, and sizes of dispersed water droplets. Based on the proposed model, the effects of fuel properties and heating conditions on the droplet heating and evaporation are analyzed.

Droplet coalescence↗
DOE OSTI2020

Ternary Phase Diagram of Water/Bio-Oil/Organic Solvent for Bio-Oil Fractionation

Separating bio-oil by fractionation with different chemical composition is a critical step to refine these oils and obtain high value products. Cold-water precipitation of pyrolytic lignin from bio-oil is the most common approach used. However, the obtained aqueous phase from this method still contain phenols, is diluted and difficult to use. In this study, the use of liquid-liquid extraction with different solvents (1-butanol, ethyl acetate, 1-octanol, dichloromethane, toluene, and hexane) for the separation of targeted molecules (lignin oligomers, sugars, acetic acid) is explored. Ternary phase diagrams for the organic solvent/water/bio-oil are reported. The partition coefficient of compounds of interest (both light and heavy fraction) is reported for the liquid-liquid equilibrium zone. When using butanol as solvent, the highest separation factor of total phenols over total sugars was observed. Furthermore, our results provide information to design L-L separation units with the capacity to selectively recover targeted molecules from pyrolysis oils.

09 BIOMASS FUELS↗
DOE OSTI2022

Conversion of Phenolic Oil from Biomass Pyrolysis into Phenyl Esters

Bio-oil is among the most economical approaches for advanced biofuel production. However, bio-oil faces several challenges including high acidity and viscosity, poor storage, and thermal stability. This study focuses on the upgradation of lignocellulosic (corn stover and yellow pine) bio-oil derived phenolic oil (PO), produced by the autothermal fast pyrolysis, through acid-catalyzed esterification reaction. Our strategy exploits a little recognized chemistry: the Fischer esterification of PO and carboxylic acids into carboxylic acid phenyl esters (CAPE) using Dean Stark distillation. Analyses by the Folin–Ciocalteu method, Karl Fischer titration, gas chromatography flame ionization detector, and the molecular weight determination by gel permeation chromatography suggest the conversion of 50 wt% added phenolics to their corresponding CAPE. The Fourier transform infrared spectroscopy analysis confirmed the formation of new C=O and two C–O stretching bands and decrease in the intensity of phenolic-OH bands in the CAPE. The 13 C NMR analysis supports the formation of CAPE together with some unreacted precursors. A base-catalyzed ester hydrolysis experiment and mass balance calculation show an excellent agreement (within 5% range) of the equivalent weight between the produced ester and the phenyl hexanoate. Brookfield analysis indicates that CAPE has 330-fold lower viscosity than starting PO. Heating values of CAPE were higher than PO, from which they were derived (42.2 and 43.6%, respectively, for PO from pyrolysis of corn stover and yellow pine), while moisture content decreased by 98.3 and 98.7%, respectively. The CAPE, which is a phenolic analogue of methyl esters used in biodiesel, has improved stability compared to PO from which it was derived.

42 ENGINEERING↗
DOE OSTI2024

Liquid–Liquid Equilibrium Prediction in Fast Pyrolysis Bio-Oil Systems: A Framework for Incorporating Bio-Oil Complexity

The study of mixtures of bio-oil, water and organic solvents in different proportions can serve as a cost-effective analysis of its content due to the formation of immiscible phases. This manuscript attempts to replicate experimentally determined partition coefficients (K OW ) of relevant species present in fast pyrolysis bio-oil (FPBO). A commercial flowsheeting simulator with surrogate bio-oil model representation is used. Concurrently, pyrolytic lignins in FPBO (‘pyrolignin’) do not have an agreed-upon structural representation, and the literature is ripe with wide variations of said representations. Thus, during the description of FPBO, this pyrolignin fraction was modeled using 20 possible structures (phenolic dimers to tetramers), with the goal of determining the structures for which the experimental data are best described. Two cases were considered: Case 1 normalized the reported experimental mass balance, while Case 2 included the unreported fraction in the mass balance to the total pyroligin. Please, add here a comment on the prediction of the Water oil equilibrium. The best KOW predictions for levoglucosan (LVG) were obtained when the system was modeled with no pyrolignin, presenting an MRE under 10% for both systems WO and BO. Among the possible structures, D2 (dimer), F1 (trimer) and I1, and I3 (tetramers) presented MRE ≤ 13% for both cases.

09 BIOMASS FUELS↗
DOE OSTI2017

Metabolic and spatio-taxonomic response of uncultivated seafloor bacteria following the Deepwater Horizon oil spill

The release of 700 million liters of oil into the Gulf of Mexico over a few months in 2010 produced dramatic changes in the microbial ecology of the water and sediment. Here in this work, we reconstructed the genomes of 57 widespread uncultivated bacteria from post-spill deep-sea sediments, and recovered their gene expression pattern across the seafloor. These genomes comprised a common collection of bacteria that were enriched in heavily affected sediments around the wellhead. Although rare in distal sediments, some members were still detectable at sites up to 60 km away. Many of these genomes exhibited phylogenetic clustering indicative of common trait selection by the environment, and within half we identified 264 genes associated with hydrocarbon degradation. Alkane degradation ability was near ubiquitous among candidate hydrocarbon degraders, whereas just three harbored elaborate gene inventories for the degradation of alkanes and aromatic and polycyclic aromatic hydrocarbons (PAHs). Differential gene expression profiles revealed a spill-promoted microbial sulfur cycle alongside gene upregulation associated with PAH degradation. Gene expression associated with alkane degradation was widespread, although active alkane degrader identities changed along the pollution gradient. Finally, analyses suggest that a broad metabolic capacity to respond to oil inputs exists across a large array of usually rare indigenous deep-sea bacteria.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2014

Biomass Feedstocks for Renewable Fuel Production: A review of the impacts of feedstock and pretreatment on the yield and product distribution of fast pyrolysis bio-oils and vapors

Renewable transportation fuels from biomass have the potential to substantially reduce greenhouse gas emissions and diversify global fuel supplies. Thermal conversion by fast pyrolysis converts up to 75% of the starting plant material (and its energy content) to a bio-oil intermediate suitable for upgrading to motor fuel. Woody biomass, by far the most widely-used and researched material, is generally preferred in thermochemical processes due to its low ash content and high quality bio-oil produced. However, the availability and cost of biomass resources, e.g. forest residues, agricultural residues, or dedicated energy crops, vary greatly by region and will be key determinates in the overall economic feasibility of a pyrolysis-to-fuel process. Formulation or blending of various feedstocks, combined with thermal and/or chemical pretreatment, could facilitate a consistent, high-volume, lower-cost biomass supply to an emerging biofuels industry. However, the impact of biomass type and pretreatment conditions on bio-oil yield and quality, and the potential process implications, are not well understood. This literature review summarizes the current state of knowledge regarding the effect of feedstock and pretreatments on the yield, product distribution, and upgradability of bio-oil.

09 BIOMASS FUELS↗
DOE OSTI2023

Developing Non-Food Grade Brassica Biofuel Feedstock Cultivars with High Yield, Oil Content, and Oil Quality that are Suitable for Low Input Production Dryland Systems (Final Report)

The U.S. uses a substantial amount of fossil fuel as an energy source for a wide range for functions including home heating, agriculture and transportation. In the transportation sector, diesel and jet fuel are consumed at a rapid rate, and alternative liquid energy is being investigated globally and nationally to reduce our dependence on fossil fuel and reduce the impact of our carbon footprint on global climate change. Non-food Brassica crops have the potential of producing high oil yield (over 250 gal acre-1) and have oil quality highly desirable for use as biodiesel or bio jet fuel. Developing oilseed feedstock Brassica cultivars with higher seed and oil yield, with high oil quality and with resistance to pathogens, that can be grown with few chemical inputs will helping break our dependence on fossil fuels and reduce importation of fossil fuels. While some oilseed Brassicas have been grown on a small scale for many years in the Pacific Northwest (PNW), adoption has been limited, and the potential of the crops have not been realized or even fully investigated. This report summarizes the results of a study to develop superior non-food grade winter (B. napus) and spring (B. napus and B. juncea) oilseed cultivars suitable for a range of PNW, and other US environments with high resistance to the biotic and abiotic stresses suitable for high-quality biofuel feedstocks. In conducting this work, genome-wide association selection was used to dissect the genetic architecture of industrial Brassica oilseed germplasm for yield, quality, and resistance to biotic and abiotic stresses. A genome-wide bioinformatics approach was used to identify putative PRR (pattern recognition receptor) - type resistance genes that confer durable resistance to blackleg. A novel transgenic approach was developed to generate resistant non-food oilseed lines using PPR genes Br1033 and Br8486. These genes were inserted into regionally adapted oilseed cultivars.

09 BIOMASS FUELS↗
NASA NTRS1969

Discrimination of fish oil and mineral oil slicks on sea water

Fish oil and mineral oil slicks on sea water can be discriminated by their different spreading characteristics and by their reflectivities and color variations over a range of wavelengths. Reflectivities of oil and oil films are determined using a duel beam reflectance apparatus.

Mac Dowall, J.↗
NASA NTRS1982

Analysis of remote sensing data collected for detection and mapping of oil spills: Reduction and analysis of multi-sensor airborne data of the NASA Wallops oil spill exercise of November 1978

Airborne, remotely sensed data of the NASA Wallops controlled oil spill were corrected, reduced and analysed. Sensor performance comparisons were made by registering data sets from different sensors, which were near-coincident in time and location. Multispectral scanner images were, in turn, overlayed with profiles of correlation between airborne and laboratory-acquired fluorosensor spectra of oil; oil-thickness contours derived (by NASA) from a scanning fluorosensor and also from a two-channel scanning microwave radiometer; and synthetic aperture radar X-HH images. Microwave scatterometer data were correlated with dual-channel (UV and TIR) line scanner images of the oil slick.

Source record↗
NASA NTRS2012

Comparison of an Inductance In-Line Oil Debris Sensor and Magnetic Plug Oil Debris Sensor

The objective of this research was to compare the performance of an inductance in-line oil debris sensor and magnetic plug oil debris sensor when detecting transmission component health in the same system under the same operating conditions. Both sensors were installed in series in the NASA Glenn Spiral Bevel Gear Fatigue Rig during tests performed on 5 gear sets (pinion/gear) when different levels of damage occurred on the gear teeth. Results of this analysis found both the inductance in-line oil debris sensor and magnetic plug oil debris sensor have benefits and limitations when detecting gearbox component damage.

Dempsey, Paula J.↗
DOE OSTI2023

Recent Progress in Electrochemical Upgrading of Bio-Oil Model Compounds and Bio-Oils to Renewable Fuels and Platform Chemicals

Sustainable production of renewable carbon-based fuels and chemicals remains a necessary but immense challenge in the fight against climate change. Bio-oil derived from lignocellulosic biomass requires energy-intense upgrading to produce usable fuels or chemicals. Traditional upgrading methods such as hydrodeoxygenation (HDO) require high temperatures (200–400 °C) and 200 bar of external hydrogen. Electrochemical hydrogenation (ECH), on the other hand, operates at low temperatures (<80 °C), ambient pressure, and does not require an external hydrogen source. These environmental and economically favorable conditions make ECH a promising alternative to conventional thermochemical upgrading processes. ECH combines renewable electricity with biomass conversion and harnesses intermediately generated electricity to produce drop-in biofuels. This review aims to summarize recent studies on bio-oil upgrading using ECH focusing on the development of novel catalytic materials and factors impacting ECH efficiency and products. Here, electrode design, reaction temperature, applied overpotential, and electrolytes are analyzed for their impacts on overall ECH performance. We find that through careful reaction optimization and electrode design, ECH reactions can be tailored to be efficient and selective for the production of renewable fuels and chemicals. Preliminary economic and environmental assessments have shown that ECH can be viable alternative to convention upgrading technologies with the potential to reduce CO2 emissions by 3 times compared to thermochemical upgrading. While the field of electrochemical upgrading of bio-oil has additional challenges before commercialization, this review finds ECH a promising avenue to produce renewable carbon-based drop-in biofuels. Finally, based on the analyses presented in this review, directions for future research areas and optimization are suggested.

09 BIOMASS FUELS↗
DOE OSTI2013

A Forecast of Crude Oil Production from Carbon Dioxide Enhanced Oil Recovery in the United States through 2018

CO2 supply for enhanced oil recovery operations in the United States is expected to increase 64% between 2012 and 2018, from 3.3 BCFd to 5.4 BCFd. The CO2 utilization rate (URNet the amount of CO2 supplied per incremental barrel of crude oil produced) can be used to estimate crude oil production based on CO2 supply rate. Based on compiled historical data we estimate the following regional CO2 Utilization rates: Permian basin, 8,500 scf/bbl, Rocky mountain, 8,000 scf/bbl, Gulf Coast, 25,000 scf/bbl. Applying these rates to the regional forecast for CO2 supply we forecast production from CO2 EOR in the United States in 2018 will be 500,000 bpd.

GHG↗
DOE OSTI2020

3D Structure of Oil Droplets in Hardened Geopolymer Emulsions: Impact of Various Commercial Liquid Oils - 20184

Cement-based solidification/stabilization (S/S) is a widely applied technique for the immobilization of inorganic hazardous constituents. However, S/S is considered less compatible for organic liquid waste (OLW) because organic compounds may inhibit binder hydration. Geopolymers (i.e. alumino-silicate materials) are an alternative for applications in which Portland cements are inappropriate. In a previous work, we proposed a direct immobilization of organic liquid waste in a geopolymer binder (GEOIL composite). We demonstrated the feasibility for producing various composites on model system (hexadecane) and on a hydraulic oil, which are dispersed in the geopolymer binder as droplets (10-50 μm typical size). In nuclear facilities, legacy waste based on organic liquids are currently stored. Many of them have been used for various applications in the nuclear industry (lubrication, cutting, analysis, liquid/liquid extraction..) with very wide chemical compositions. In this study, we study the influence of various commercial organic oils immobilized in hardened geopolymer emulsions by X-ray micro-tomography. Image analysis make it possible to determine the 3D spatial and size distributions of oil droplets in geopolymer emulsions. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2018

Improved Lubricating Performance by Combining Oil-Soluble Hairy Silica Nanoparticles and an Ionic Liquid as an Additive for a Synthetic Base Oil

This article reports on improved lubricating performance by combining oil-soluble poly(lauryl methacrylate) brush-grafted silica nanoparticles (hairy NPs or HNP) and an oil-miscible phosphonium-phosphate ionic liquid (IL) as a friction-reducing additive for a polyalphaolefin (PAO) oil. The HNP was synthesized by surface-initiated reversible addition–fragmentation chain transfer polymerization. At a total concentration of 2% and sufficiently high individual concentrations for HNP and IL in PAO, high-contact stress, ball-on-flat reciprocating tribological tests showed that the friction decreased by up to 23% compared with 2% HNP alone in PAO and by up to 35% compared to the PAO mixed with 2% IL. Scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy (XPS) analysis revealed that the tribofilm formed from the PAO containing 1% HNP + 1% IL was enriched with both Si and P, indicating that both hairy NPs and IL were involved in the tribochemical reactions. In addition, the O 1s and Si 2p peaks in the core-level XPS spectra exhibited significant shifts for the mixture of 1% HNP + 1% IL compared to those for 2% HNP, suggesting the possible formation of new covalent bonds. These results indicated that HNP and IL reacted with each other and also with the metal substrate during the rubbing process, which likely strengthened the tribofilm and its bonding with the substrate and thus further improved the lubrication.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Structural transitions of 4:1 methanol–ethanol mixture and silicone oil under high pressure

A 4:1 (volume ratio) methanol–ethanol (ME) mixture and silicone oil are two of the most widely used liquid pressure-transmitting media (PTM) in high-pressure studies. Their hydrostatic limits have been extensively studied using various methods; however, the evolution of the atomic structures associated with their emerging nonhydrostaticity remains unclear. Here, we monitor their structures as functions of pressure up to ∼30 GPa at room temperature using in situ high-pressure synchrotron x-ray diffraction (XRD), optical micro-Raman spectroscopy, and ruby fluorescence spectroscopy in a diamond anvil cell. No crystallization is observed for either PTM. The pressure dependence of the principal diffraction peak position and width indicates the existence of a glass transition in the 4:1 ME mixture at ∼12 GPa and in the silicone oil at ∼3 GPa, beyond which a pressure gradient emerges and grows quickly with pressure. There may be another liquid-to-liquid transition in the 4:1 ME mixture at ∼5 GPa and two more glass-to-glass transitions in the silicone oil at ∼10 GPa and ∼16 GPa. By contrast, Raman signals only show peak weakening and broadening for typical structural disordering, and Raman spectroscopy seems to be less sensitive than XRD in catching these structural transitions related to hydrostaticity variations in both PTM. These results uncover rich pressure-induced transitions in the two PTM and clarify their effects on hydrostaticity with direct structural evidence. The high-pressure XRD and Raman data on the two PTM obtained in this work could also be helpful in distinguishing between signals from samples and those from PTM in future high-pressure experiments.

Chen, Xiehang (ORCID:0000000168541506)↗
DOE OSTI2017

Impact of Expanded North Slope of Alaska Crude Oil Production on Crude Oil Flows in the Contiguous United States

The National Transportation Fuels Model was used to simulate a hypothetical increase in North Slope of Alaska crude oil production. The results show that the magnitude of production utilized depends in part on the ability of crude oil and refined products infrastructure in the contiguous United States to absorb and adjust to the additional supply. Decisions about expanding North Slope production can use the National Transportation Fuels Model take into account the effects on crude oil flows in the contiguous United States.

02 PETROLEUM↗
NASA NTRS1983

Oil film thickness using airborne laser-induced oil fluorescence backscatter

Remote airborne measurement of oil film thickness on ocean surface using laser-induced water Raman backscatter is discussed. It is pointed out that the theoretical model of oil fluorescence by Horvath et al. (1971) contains the necessary constituents to provide for the natural background fluorescence that is also induced by the laser during the course of an oil thickness experiment. How the various parameters of the model are obtained from typical airborne profile data is discussed, and it is shown that the water Raman backscatter may be used to assist further in the application of the data. The regions or water types over which the technique might be most useful or applicable are discussed.

Hoge, F. E.↗