Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Morphological”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Eruptive viscosity and volcano morphology

Terrestrial central volcanoes formed predominantly from lava flows were classified as shields, stratovolcanoes, and domes. Shield volcanoes tend to be large in areal extent, have convex slopes, and are characterized by their resemblance to inverted hellenic war shields. Stratovolcanoes have concave slopes, whereas domes are smaller and have gentle convex slopes near the vent that increase near the perimeter. In addition to these differences in morphology, several other variations were observed. The most important is composition: shield volcanoes tend to be basaltic, stratovolcanoes tend to be andesitic, and domes tend to be dacitic. However, important exceptions include Fuji, Pico, Mayon, Izalco, and Fuego which have stratovolcano morphologies but are composed of basaltic lavas. Similarly, Ribkwo is a Kenyan shield volcano composed of trachyte and Suswa and Kilombe are shields composed of phonolite. These exceptions indicate that eruptive conditions, rather than composition, may be the primary factors that determine volcano morphology. The objective of this study is to determine the relationships, if any, between eruptive conditions (viscosity, erupted volume, and effusion rate) and effusive volcano morphology. Moreover, it is the goal of this study to incorporate these relationships into a model to predict the eruptive conditions of extraterrestrial (Martian) volcanoes based on their morphology.

Posin, Seth B.↗
NASA NTRS1990

Growth morphology with anisotropic surface kinetics

The morphological evolution of crystals growing from an incongruent vapor phase is studied using a Monte Carlo model, and the full range of growth morphologies is recovered. The diffusion in the bulk nutrient and the anisotropy in the interface kinetics are morphologically destabilizing and stabilizing, respectively. For a given set of simulation parameters and lattice symmetries there is a critical size, which scales linearly with the mean free path in the vapor, beyond which a crystal cannot retain its stable, macroscopically faceted growth shape. Surface diffusion stabilizes faceted growth on the shorter scale of the mean surface diffusion length. In simulations with a uniform drift superimposed on the random walk nutrient transport, crystal faces oriented toward the drift show enhanced morphological stability compared to the purely diffusive situation. Rotational drifts with periodic reversal of direction are morphologically stabilizing for all crystal facets.

Xiao, Rong-Fu↗
NASA NTRS1991

Randomization of dust-ejecta motions and the observed morphology of cometary heads

The computer code that has been used over years to study the dust-coma morphology of comets and to generate their synthetic images is upgraded by introducing two categories of random perturbations into the motions of dust particles ejected from discrete sources of activity on the nucleus surface. The new technique is applied to three types of morphological features: multiple concentric halos, a system of spiral jets, and a sunward fan-shaped coma. The results indicate that inclusion of random perturbations substantially enhances the capability for generating synthetic images that faithfully simulate the observed appearance of dust comets. By increasing the magnitude of perturbations in the synthetic images beyond a certain limit, it is possible to 'erase' morphological features characteristic of the ejection process. This implies that the lack of distinct morphology in the head of a comet cannot be interpreted as the absence of discrete sources of activity on the nucleus surface. The effects of varying random perturbations on the appearance of the computer-generated images are investigated in detail and the suspected major role that imperfect flow collimation (or flow divergence) in dust jets plays with regard to the observed coma morphology is discussed.

Sekanina, Zdenek↗
NASA NTRS1993

Kinematics of compact groups and morphologies of the member galaxies

We present the results of a kinematical and morphological study of galaxies in the Hickson compact groups. The redshift survey of 457 galaxies has been completed. The great majority of the galaxies have velocities within about 1000 km/s(exp -1) of the median velocity of the group. The velocities of the groups range from 1380 to 41731 km/s(exp -1) with a median of 8889 km/s(exp -1), corresponding to a median distance of 89 h(exp -1)Mpc. With the addition of the radial velocity selection criterion, a relatively large sample of physically dense compact groups was defined. The nature of the velocity dispersion-morphology relation (Hickson, Kindl and Huchra 1989, hereafter HKH) is investigated. This is the tendency of groups with high velocity dispersions to contain fewer late type galaxies. We find that this strong correlation is not due to any sample selection effects. The morphology concordance in compact groups (HKH), which is the trend for galaxies in a group to have similar morphological types, can be fully explained by the velocity dispersion-morphology correlation. A significant correlation is found between crossing time and the fraction of gas-rich galaxies in the groups. Groups with short crossing times typically contain fewer late-type galaxies. This may be evidence that significant dynamical evolution has occurred in these groups.

Mendesdeoliveira, Claudia↗
NASA NTRS1997

Process-Induced Morphological Defects in Epitaxial CVD Silicon Carbide

Silicon carbide (SiC) semiconductor technology has been advancing rapidly, but there are numerous crystal growth problems that need to be solved before SiC can reach its full potential. Among these problems is a need for an improvement in the surface morphology of epitaxial films that are grown to produce device structures. Various processes before and during epilayer growth lead to the formation of morphological defects observed in SiC epilayers grown on SiC substrates. In studies of both 6H and 4H-SiC epilayers, atomic force microscopy (AFM) and other techniques have been used to characterize SiC epilayer surface morphology. In addition to the well-known micropipe defect, SiC epilayers contain growth pits, triangular features (primarily) in 4H-SiC, and macro step due to step bunching. In work at NASA Lewis, it has been found that factors contributing to the formation of some morphological defects include: defects in the substrate bulk, defects in the substrate surface caused by cutting and polishing the wafer, the tilt angle of the wafer surface relative to the basal plane, and growth conditions. Some of these findings confirm results of other research groups. This paper presents a review of published and unpublished investigations into processes that are relevant to epitaxial film morphology.

Powell, J. A.↗
NASA NTRS1998

Phylogenetic mapping of bacterial morphology

The availability of a meaningful molecular phylogeny for bacteria provides a context for examining the historical significance of various developments in bacterial evolution. Herein, the classical morphological descriptions of selected members of the domain Bacteria are mapped upon the genealogical ancestry deduced from comparison of small-subunit rRNA sequences. For the species examined in this study, a distinct pattern emerges which indicates that the coccus shape has arisen and accumulated independently multiple times in separate lineages and typically survived as a persistent end-state morphology. At least two other morphologies persist but have evolved only once. This study demonstrates that although bacterial morphology is not useful in defining bacterial phylogeny, it is remarkably consistent with that phylogeny once it is known. An examination of the experimental evidence available for morphogenesis as well as microbial fossil evidence corroborates these findings. It is proposed that the accumulation of persistent morphologies is a result of the biophysical properties of peptidoglycan and their genetic control, and that an evolved body-plan strategy based on peptidoglycan may have been a fate-sealing step in the evolution of Bacteria. More generally, this study illustrates that significant evolutionary insights can be obtained by examining biological and biochemical data in the context of a reliable phylogenetic structure.

NASA Discipline Exobiology↗
NASA NTRS2004

Comparing morphologies of drainage basins on Mars and Earth using integral-geometry and neural maps

We compare morphologies of drainage basins on Mars and Earth in order to confine the formation process of Martian valley networks. Basins on both planets are computationally extracted from digital topography. Integral-geometry methods are used to represent each basin by a circularity function that encapsulates its internal structure. The shape of such a function is an indicator of the style of fluvial erosion. We use the self-organizing map technique to construct a similarity graph for all basins. The graph reveals systematic differences between morphologies of basins on the two planets. This dichotomy indicates that terrestrial and Martian surfaces were eroded differently. We argue that morphologies of Martian basins are incompatible with runoff from sustained, homogeneous rainfall. Fluvial environments compatible with observed morphologies are discussed. We also construct a similarity graph based on the comparison of basins hypsometric curves to demonstrate that hypsometry is incapable of discriminating between terrestrial and Martian basins. INDEX TERMS: 1824 Hydrology: Geomorphology (1625); 1886 Hydrology: Weathering (1625); 5415 Planetology: Solid Surface Planets: Erosion and weathering; 6225 Planetology: Solar System Objects Mars. Citation: Stepinski, T. F., and S. Coradetti (2004), Comparing morphologies of drainage basins on Mars and Earth using integral-ge

Stepinski, T. F.↗
NASA NTRS1993

Opto-electronic morphological processor

The opto-electronic morphological processor of the present invention is capable of receiving optical inputs and emitting optical outputs. The use of optics allows implementation of parallel input/output, thereby overcoming a major bottleneck in prior art image processing systems. The processor consists of three components, namely, detectors, morphological operators and modulators. The detectors and operators are fabricated on a silicon VLSI chip and implement the optical input and morphological operations. A layer of ferro-electric liquid crystals is integrated with a silicon chip to provide the optical modulation. The implementation of the image processing operators in electronics leads to a wide range of applications and the use of optical connections allows cascadability of these parallel opto-electronic image processing components and high speed operation. Such an opto-electronic morphological processor may be used as the pre-processing stage in an image recognition system. In one example disclosed herein, the optical input/optical output morphological processor of the invention is interfaced with a binary phase-only correlator to produce an image recognition system.

Yu, Jeffrey W.↗
NASA NTRS2018

Scattering and Radiative Properties of Morphologically Complex Carbonaceous Aerosols: A Systematic Modeling Study

This paper provides a thorough modeling-based overview of the scattering and radiative properties of a wide variety of morphologically complex carbonaceous aerosols. Using the numerically-exact superposition T-matrix method, we examine the absorption enhancement, absorption Angstroem exponent (AAE), backscattering linear depolarization ratio (LDR), and scattering matrix elements of black-carbon aerosols with 11 different model morphologies ranging from bare soot to completely embedded soot-sulfate and soot-brown carbon mixtures. Our size-averaged results show that fluffy soot particles absorb more light than compact bare-soot clusters. For the same amount of absorbing material, the absorption cross section of internally mixed soot can be more than twice that of bare soot. Absorption increases as soot accumulates more coating material and can become saturated. The absorption enhancement is affected by particle size, morphology, wavelength, and the amount of coating. We refute the conventional belief that all carbonaceous aerosols have AAEs close to 1.0. Although LDRs caused by bare soot and certain carbonaceous particles are rather weak, LDRs generated by other soot-containing aerosols can reproduce strong depolarization measured by Burton et al. for aged smoke. We demonstrate that multi-wavelength LDR measurements can be used to identify the presence of morphologically complex carbonaceous particles, although additional observations can be needed for full characterization. Our results show that optical constants of the host/coating material can significantly influence the scattering and absorption properties of soot-containing aerosols to the extent of changing the sign of linear polarization. We conclude that for an accurate estimate of black-carbon radiative forcing, one must take into account the complex morphologies of carbonaceous aerosols in remote sensing studies as well as in atmospheric radiation computations.

carbonaceous aerosols; scattering matrix; polariza↗
NASA NTRS2026

Modeling Study of Hatch Spacing’s Effect on Grain Morphology in Repairing Damaged Metal Parts with Welding and Hatch Spacing’s Potential Use in Lunar Exploration

The welding process is a potential way of repairing a damaged metal component, especially cavity damage caused by a harsh environment like the lunar environment, which is characterized by large temperature differences and reduced gravity. The adjustment of welding parameter (e.g., hatch spacing) can improve production efficiency in the repair process. Seen from the microstructural level, hatch spacing sensitivity affects the metallic grain evolution and morphology in the welding process, which can further influence a repaired part’s mechanical properties; however, the study of hatch spacing’s effect on microstructure is challenging. Traditional experimental procedures are costly and time-consuming, and any change in hatch spacing value needs roll-back of experimental procedure. A modeling study can address the above challenges in experimental observation. In this research, a modeling approach based on the Kinetic Monte Carlo (KMC) Potts theory was used to simulate grain evolution and morphology with three hatch spacings. Through quantifying and analyzing the predicted grain morphologies, the effect of hatch spacing on microstructure in a welding-fabricated part was investigated. The predicted grain morphologies were validated with an EBSD image of welding microstructure, which has been published before. The primary grain morphologies were columnar grains with a small amount of fine equiaxed grains formed in the scanning path centerline. When increasing the hatch spacing, the columnar grains become larger and more lengthy, while the effect of hatch spacing on the equiaxed grains is not obvious.

Welding for repairing↗
DOE OSTI2022

Metal‐Organic Framework (MOF) Morphology Control by Design

Abstract Exerting morphological control over metal‐organic frameworks (MOFs) is critical for determining their catalytic performance and to optimize their packing behavior in areas from separations to fuel gas storage. A mechanism‐based approach to tailor the morphology of MOFs is introduced and experimentally demonstrated for five cubic Zn 4 O‐based MOFs. This methodology provides three key features: 1) computational screening for selection of appropriate additives to change crystal morphology based on knowledge of the crystal structure alone; 2) use of additive to metal cluster geometric relationships to achieve morphologies expressing desired crystallographic facets; 3) potential for suppression of interpenetration for certain phases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Optimization of anionic conductivity through the coexistence of ionomer cluster and backbone-backbone morphologies in anion exchange membranes

Random copolymers of poly(4-vinylpyridine) and polyisoprene were synthesized, and subsequently quaternized with 1-alkylbromides. The number of carbons on the pendant side-chain of the resultant comb-shaped polymer, n, ranged from 2-8. The comb-shaped polymers were crosslinked employing thiol-ene chemistry to give mechanically robust ion conducting membranes. Analysis by wide and medium-angle X-ray scattering show three morphology regimes that are dependent on the number of carbons on the pendant side-chains. When n = 2, ionomer cluster morphology was dominant, when n = 8 backbone-backbone morphology was dominant, and when n = 3-6, the membrane showed a coexistence of both ionomer cluster and backbone-backbone morphologies. Evaluation of the water uptake of the membranes showed a maximum water uptake per cation of 9.5 when n = 5 at 95% relative humidity (RH) and 60 degrees C. Finally, conductivity of the samples characterized by electrochemical impedance spectroscopy showed bromide conductivity as high as 110 mS/cm when n = 3 at 95% RH and 90 degrees C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Dispersity-Driven Stabilization of Coexisting Morphologies in Asymmetric Diblock Copolymer Thin Films

Despite decades of research, characterization of the effects of polymer chain dispersity on the structural properties of block copolymer thin films remains challenging. Here we present an integrated experimental and modeling approach to characterize the morphology of thin films containing asymmetric diblock copolymers. Specifically, we used synergistic neutron reflectivity (NR) and self-consistent field theory (SCFT)-based modeling to realize unexpected morphology of thin films containing asymmetric copolymers. Using NR, a highly stable and reproducible mixed phase of coexisting cylinders and lamellar domains was discovered in asymmetric poly(deuterated-styrene-b-n butyl methacrylate) (dPS-PBMA) copolymer thin films containing 34% volume fraction of dPS. SCFT reveals how to obtain such a thermodynamically stable morphology in the presence of disperse majority block and asymmetric interactions of polymer species with surfaces. Stabilization of the coexisting domains is a consequence of the depth segregation based on chain-length distribution. The asymmetric chains microphase-separate into cylindrical domains close to the substrate and near-symmetric chains form lamellar domains at the air interface. In the absence of dispersity, the coexistence of cylindrical and lamellar domains is thermodynamically unstable because of the absence of depth segregation. Overall, such an effect of dispersity on diblock copolymer thin-film morphology reveals a unique and powerful strategy to create coexisting nanoscale domains and tailor properties of thin films.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Tradeoff between Intermolecular Interaction and Backbone Disorder by High Molecular Dipole Block for Improving Blend Morphology of Polymer Solar Cells

Constructing terpolymer has attracted increasing attention as a strategy to improve the performance of polymer solar cell. Terpolymer usually offers an opportunity to lower the frontier molecular orbital energy level, introduces additional absorption band and sometimes optimizes the morphology of the active blend. Generally, the additional segment in terpolymer backbone inevitably introduces backbone disorder, which causes entropy rises. However, selecting a suitable dipole unit introduces extra driving forces for crystallization by enhancing intermolecular interactions. This provides a handy knob for tradeoff between intermolecular interaction and backbone disorder, thus regulating the blend morphology. In this study, a high dipole and electron-deficient group of pyrrolo[3,4-f ]benzotriazole-5,7(6H)-dione (TzBI) is incorporated into the high-performance donor polymer and a series of terpolymers with different content of TzBI are designed. As expected, the morphology is optimized gradually for improving charge generation and charge transport, also suppressing charge recombination. The champion device with 10% TzBI exhibited a power conversion efficiency (PCE) of 18.36%, which is 5% increase compared to the controlled device. This study presents a charming terpolymer strategy by highly electron-deficient and high dipole segment to realize a tradeoff between intermolecular interaction and backbone disorder, facilitating the optimization of morphology and elevation of fill factor and device efficiency.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Smartly Optimizing Crystallinity, Compatibility, and Morphology for Polymer Solar Cells by Small Molecule Acceptor with Unique 2D-EDOT Side Chain

A desired morphology is essential for achieving efficient polymer solar cells. Donors and acceptors with appropriate crystallization can lead to a suitable phase-separated morphology for effective photocurrent generation process. Inspired by the success of Y6 acceptors and the 2D side chain engineering on popular polymer donors and small molecule acceptors, the usage of unique 2D 3,4-ethylene dioxythiophene (EDOT) side chains on Y6 to regulate its crystallinity, compatibility, and thus the related blend morphology is explored. Here, in this study, two molecules of BTP-EDOT-4F and BTP-EDOT-4Cl with such unique 2D EDOT side chains are designed and synthesized. Due to the advantage of EDOT side chain, when these molecules are blended with PM6, the decent power conversion efficiencies (PCEs) of 16.78% and 15.87% are obtained. Furthermore, BTP-EDOT-4F is selected as the third component and added into PM6:L8-BO binary system to form ternary blends. The optimized crystallinity, compatibility, and morphology of such ternary blend are discovered in the presence of BTP-EDOT-4F, which enables efficient exciton dissociation and charge transport as well as decreased recombination, resulting in higher short circuit current density (J sc ) and fill factor. Finally, the outstanding PCE of 18.56% is achieved in ternary blends containing PM6, L8-BO, and BTP-EDOT-4F.

2D EDOT side chains↗
DOE OSTI2024

Crossbreeding Effect of Chalcogenation and Iodination on Benzene Additives Enables Optimized Morphology and 19.68% Efficiency of Organic Solar Cells

Volatile solid additives have attracted increasing attention in optimizing the morphology and improving the performance of currently dominated non-fullerene acceptor-based organic solar cells (OSCs). However, the underlying principles governing the rational design of volatile solid additives remain elusive. Herein, a series of efficient volatile solid additives are successfully developed by the crossbreeding effect of chalcogenation and iodination for optimizing the morphology and improving the photovoltaic performances of OSCs. Five benzene derivatives of 1,4-dimethoxybenzene (DOB), 1-iodo-4-methoxybenzene (OIB), 1-iodo-4-methylthiobenzene (SIB), 1,4-dimethylthiobenzene (DSB) and 1,4-diiodobenzene (DIB) are systematically studied, where the widely used DIB is used as the reference. The effect of chalcogenation and iodination on the overall property is comprehensively investigated, which indicates that the versatile functional groups provided various types of noncovalent interactions with the host materials for modulating the morphology. Among them, SIB with the combination of sulphuration and iodination enabled more appropriate interactions with the host blend, giving rise to a highly ordered molecular packing and more favorable morphology. As a result, the binary OSCs based on PM6:L8-BO and PBTz-F:L8-BO as well as the ternary OSCs based on PBTz-F:PM6:L8-BO achieved impressive high PCEs of 18.87%, 18.81% and 19.68%, respectively, which are among the highest values for OSCs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Quantifying Pore Morphology in Spray-Formed Tantalum Using X-ray Micro-computed Tomography

In order to establish quantitative process–structure–property relationships in thermal spray coatings, a robust framework for defining (micro)structural characteristics is needed. Here, we present a quantitative characterization of the three-dimensional morphology of porosity in spray-formed tantalum samples based on high-resolution X-ray micro-computed tomography. Using synchrotron facilities, we acquired dozens of high-resolution scans, enabling a statistically meaningful comparison across multiple samples, different regions within samples, and spray processes. We quantify the spatial distribution, size, and topology of porous inclusions, with a significant focus on variability across samples and different spray processes (plasma and cold sprayed), as well as sensitivity to image segmentation and resolution. Based on a typical segmentation, we report porosities ranging from 0.9 to 1.7 pct for all samples tested, with significant sensitivity due to image segmentation resulting in estimates as low as 0.6 pct and as high as 4.8 pct. For the complex pore space morphology observed in these materials, we argue that a conventional analysis based on identifying individual pores is not well suited, and propose an alternative approach based on morphological metrics with a rich history in porous media literature, such as spatial correlations, local pore thickness, and scale-dependent sub-sampling. Spatial correlations indicate anisotropic splat structures, but only mildly anisotropic pores. Various measures of pore size show a wide distribution of sizes, ranging from sub-micron to 10-micron length scales. Scale-dependent variations in porosity suggest that representative volumes of several hundred microns are required for convergence of morphological metrics, with larger volumes for cold-spray materials. This work provides a robust quantitative basis for describing three-dimensional pore structure in thermal spray coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-performance organic photodetectors enabled by a refined fibrillar multiphase morphology

Film morphology of donor:acceptor blend layers plays a critical role in photon-to-current efficiency and dark/noise current of organic photodetectors (OPDs). One effective approach to manipulate crystallization and mesoscale phase separation of such blend layers is sequential casting (SC). However, the guiding strategies to control the morphology and the impacts on OPD performance of the SC films remain elusive, as the film structural evolution during SC is different from conventional blend casting (BC). In this report a refined fibrillar multiphase morphology is demonstrated by SC in an NT812:IEICO-4F blend film, where the high-quality IEICO-4F crystallites infiltrate the robust NT812 fibril network from the surface to the bulk. Such a morphology leads to improved charge generation and collection, reduced trap states, and enhanced charge block capability of resultant device, enabling simultaneous achievement of high external quantum efficiency and low dark/noise current. A maximum special detectivity of 5 × 10 13 Jones is achieved at 860 nm under –0.1 V, which is among the highest detectivities for vis-to-NIR OPDs. The linear dynamic range and response speed are also improved. Such enhancements are parallelly observed from OPD devices based on other blend systems with similar fibrillar refinement, which provides guidelines for film structure manipulation towards high OPD performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗