SEARCH · Engineering Papers

Results for “Maximum principle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

NASA NTRS1988

The dynamics and control of the in-orbit SCOLE configuration

The study of the dynamics of the Spacecraft Control Laboratory Experiment (SCOLE) is extended to emphasize the synthesis of control laws for both the linearized system as well as the large amplitude slewing maneuvers required to rapidly reorient the antenna line of sight. For control of the system through small amplitude displacements from the nominal equilibrium position LQR techniques are used to develop the control laws. Pontryagin's maximum principle is applied to minimize the time required for the slewing of a general rigid spacecraft system. The minimum slewing time is calculated based on a quasi-linearization algorithm for the resulting two point boundary value problem. The effect of delay in the control input on the stability of a continuously acting controller (designed without considering the delay) is studied analytically for a second order plant. System instability can result even for delays which are only a small fraction of the natural period of motion.

Bainum, Peter M.↗

NASA NTRS1988

The dynamics and control of large flexible space structures, part 11

A mathematical model is developed to predict the dynamics of the proposed Spacecraft Control Laboratory Experiment during the stationkeeping phase. The Shuttle and reflector are assumed to be rigid, while the mass connecting the Shuttle to the reflector is assumed to be flexible with elastic deformations small as compared with its length. It is seen that in the presence of gravity-gradient torques, the system assumes a new equilibrium position primarily due to the offset in the mass attachment point to the reflector from the reflector's mass center. Control is assumed to be provided through the Shuttle's three torquers and throught six actuators located by painrs at two points on the mass and at the reflector mass center. Numerical results confirm the robustness of an LQR derived control strategy during stationkeeping with maximum control efforts significantly below saturation levels. The linear regulator theory is also used to derive control laws for the linearized model of the rigidized SCOLE configuration where the mast flexibility is not included. It is seen that this same type of control strategy can be applied for the rapid single axis slewing of the SCOLE through amplitudes as large as 20 degrees. These results provide a definite trade-off between the slightly larger slewing times with the considerable reduction in over-all control effort as compared with the results of the two point boundary value problem application of Pontryagin's Maximum Principle.

Bainum, Peter M.↗

NASA NTRS1989

Thrust vectoring effect on time-optimal 90 degrees angle of attack pitch up maneuvers of a high alpha fighter aircraft

Using thrust vectoring, the problem of pitching up a high alpha fighter aircraft to 90 degrees angle of attack in minimum time is considered. Pontryagin's maximum principle is used together with a two-point boundary value numerical algorithm to derive open-loop controls for various parameterized limits on thrust vectoring angles. Without thrust vectoring, a high alpha fighter with initial conditions 0.6 Mach number and 15,000 feet requires 7.0 seconds to pitch-up to 90 degrees. However, with 20-degree angle thrust vectoring, the pitch-up takes only 1.5 seconds with a final Mach number of 0.47. Also, the gain in altitude is less than 100 feet. More important, additional thrust vectoring yields litle benefit beyond the 20-degree angles. This paper describes control solutions in detail for thrust vectoring angles between 0 and 90 degrees.

Stalford, Harold↗

NASA NTRS1989

Singular trajectories for time-optimal half-loop maneuvers of a high alpha fighter aircraft

Consideration is given to the problem of deriving a time-optimal open-loop control for the half-loop maneuver of a high-alpha aircraft, with initial conditions Mach 0.6 and 15,000 feet. Pontriagin's maximum principle is used to derive candidate optimal solutions. Using the two-point boundary-value algorithm, the flight path angle is maximized for various increasing specified final times until a final time of 13.6 sec yields a 180-deg flight-path angle. As the final time increased from 0.0 to 13.6 sec, the optimization process revealed 13 distinct switching structures of the control law, of which 11 contained singular arcs, and two had double singular arcs.

Hoffman, Eric↗

NASA NTRS1989

Use of the quasilinearization algorithm for the simulation of LSS slewing

The use of the Maximum Principle for the large angle slewing of large space structures (LSS) usually results in the so-called two-point boundary-value problem, in which many requirements (e.g., minimum time, small amplitude, and limited control power, etc.) must be satisfied simultaneously. The successful solution of this problem depends largely on the use of an efficient numerical algorithm. There are many candidate algorithms available for this problem (e.g., quasilinearization, gradient, etc.). Here researchers discuss only the quasilinearization method which has been used for several cases of large angle slewing of LSS. The basic idea of this algorithm is to make a series of successive approximations of the solution from a particular solvable case (linear or nonlinear) to a more general practical case. For the rigid spacecraft slewing problem with no constraints on the controls, the solution procedure can be found in the literature. This procedure needs to be modified if a minimum time for the slewing problem is desired with control limits given. Recently, an indirect method for finding the minimum time was developed to meet all these requirements. For the general mixed (including both rigid and flexible parts) problem, an additional constraint of small vibrational amplitude on the flexible parts is imposed.

Li, Feiyue↗

NASA NTRS1989

The dynamics and control of large flexible space structures - 12, supplement 11

The rapid 2-D slewing and vibrational control of the unsymmetrical flexible SCOLE (Spacecraft Control Laboratory Experiment) with multi-bounded controls is considered. Pontryagin's Maximum Principle is applied to the nonlinear equations of the system to derive the necessary conditions for the optimal control. The resulting two point boundary value problem is then solved by using the quasilinearization technique, and the near minimum time is obtained by sequentially shortening the slewing time until the controls are near the bang-bang type. The tradeoff between the minimum time and the minimum flexible amplitude requirements is discussed. The numerical results show that the responses of the nonlinear system are significantly different from those of the linearized system for rapid slewing. The SCOLE station-keeping closed loop dynamics are re-examined by employing a slightly different method for developing the equations of motion in which higher order terms in the expressions for the mast modal shape functions are now included. A preliminary study on the effect of actuator mass on the closed loop dynamics of large space systems is conducted. A numerical example based on a coupled two-mass two-spring system illustrates the effect of changes caused in the mass and stiffness matrices on the closed loop system eigenvalues. In certain cases the need for redesigning control laws previously synthesized, but not accounting for actuator masses, is indicated.

Bainum, Peter M.↗

NASA NTRS1990

Shock-layer bounds for a singularly perturbed equation

The size of the shock-layer governed by a conservation law is studied. The conservation law is a parabolic reaction-convection-diffusion equation with a small parameter multiplying the diffusion term and convex flux. Rigorous upper and lower bounding functions for the solution of the conservation law are established based on maximum-principle arguments. The bounding functions demonstrate that the size of the shock-layer is proportional to the parameter multiplying the diffusion term.

Scroggs, Jeffrey S.↗

NASA NTRS1990

The dynamics and control of large flexible space structures - 13

The optimal control of three-dimensional large angle maneuvers and vibrations of a Shuttle-mast-reflector system is considered. The nonlinear equations of motion are formulated by using Lagrange's formula, with the mast modeled as a continuous beam subject to three-dimensional deformations. Pontryagin's Maximum Principle is applied to the slewing problem, to derive the necessary conditions for the optimal controls, which are bounded by given saturation levels. The resulting two point boundary value problem is then solved by using the quasilinearization algorithm and the method of particular solutions. The study of the large angle maneuvering of the Shuttle-beam-reflector spacecraft in the plane of a circular earth orbit is extended to consider the effects of the structural offset connection, the axial shortening, and the gravitational torque on the slewing motion. Finally the effect of additional design parameters (such as related to additional payload requirement) on the linear quadratic regulator based design of an orbiting control/structural system is examined.

Bainum, Peter M.↗

NASA NTRS1990

Rapid in-plane maneuvering of the flexible orbiting SCOLE

The rapid two-dimensional slewing and vibrational control of the unsymmetrical flexible SCOLE (Spacecraft Control Laboratory Experiment) with multi-bounded controls has been considered. Pontryagin's Maximum Principle has been applied to the nonlinear equations of the system to derive the necessary conditions for the optimal control. The resulting two-point boundary-value problem is then solved by using the quasilinearization technique, and the near-minimum time is obtained by sequentially shortening the slewing time until the controls are near the bang-bang type. The trade-off between the minimum time and the minimum flexible amplitude requirements has been discussed. The numerical results show that the responses of the nonlinear system are significantly different from those of the linearized system for rapid slewing.

Bainum, Peter M.↗

NASA NTRS1990

Nonlinear feedback control for high alpha flight

Analytical aerodynamic models are derived from a high alpha 6 DOF wind tunnel model. One detail model requires some interpolation between nonlinear functions of alpha. One analytical model requires no interpolation and as such is a completely continuous model. Flight path optimization is conducted on the basic maneuvers: half-loop, 90 degree pitch-up, and level turn. The optimal control analysis uses the derived analytical model in the equations of motion and is based on both moment and force equations. The maximum principle solution for the half-loop is poststall trajectory performing the half-loop in 13.6 seconds. The agility induced by thrust vectoring capability provided a minimum effect on reducing the maneuver time. By means of thrust vectoring control the 90 degrees pitch-up maneuver can be executed in a small place over a short time interval. The agility capability of thrust vectoring is quite beneficial for pitch-up maneuvers. The level turn results are based currently on only outer layer solutions of singular perturbation. Poststall solutions provide high turn rates but generate higher losses of energy than that of classical sustained solutions.

Stalford, Harold↗

NASA NTRS1990

Multiple strike slip faults sets: A case study from the Dead Sea transform

In many strike slip tectonic settings, large rotations of crust blocks about vertical axes have been inferred from paleomagnetic data. These blocks are bounded by sets of parallel faults which presumably accommodate the relative motion between the blocks as regional deformation progress. A mechanical model by Nur et al., (1986) suggests that rotations greater than phi sub c equals 25 to 45 degrees must be accommodated by more than one set of faults, with angle phi sub c between their direction; consequently the sum of the angles between sets must be roughly equal to the total tectonic material rotation. To test this model, the authors investigated the fault geometry and field relation of fault sets in the Mt. Hermon area in northern Israel, where paleomagnetic declination implies data 69 degrees plus or minus 13 degrees counter-clockwise block rotation. The statistical and field relation analysis of over 315 faults shows that the faulting is predominantly right lateral strike slip consisting of three distinct sets. The oldest set strikes 253 degrees, the second oldest set strikes 293 degrees and the youngest strikes 339 degrees. This last direction is consistent also with the current north-south direction of the maximum principle stress axis. The angle phi sub c between the first and second sets is 39 degrees and between the second and third sets 46 degrees, in good agreement with the phi sub c angle predicted from mechanical considerations. The sum of the two angles is 85 degrees, in good agreement with the 69 degrees plus or minus 13 degrees CCW paleomagnetically derived rotation. The results suggest specifically that the sequential development of multiple intersecting fault sets is responsible for the faulting in the Mt. Hermon area; and generally that the model of block rotation with multiple faults provides very good simple rules for analyzing very complex fault patterns.

Ron, Hagai↗

NASA NTRS1991

Maneuver simulations of flexible spacecraft by solving TPBVP

The optimal control of large angle rapid maneuvers and vibrations of a Shuttle mast reflector system is considered. The nonlinear equations of motion are formulated by using Lagrange's formula, with the mast modeled as a continuous beam. The nonlinear terms in the equations come from the coupling between the angular velocities, the modal coordinates, and the modal rates. Pontryagin's Maximum Principle is applied to the slewing problem, to derive the necessary conditions for the optimal controls, which are bounded by given saturation levels. The resulting two point boundary value problem (TPBVP) is then solved by using the quasilinearization algorithm and the method of particular solutions. In the numerical simulations, the structural parameters and the control limits from the Spacecraft Control Lab Experiment (SCOLE) are used. In the 2-D case, only the motion in the plane of an Earth orbit or the single axis slewing motion is discussed. In the 3-D slewing, the mast is modeled as a continuous beam subjected to 3-D deformations. The numerical results for both the linearized system and the nonlinear system are presented to compare the differences in their time response.

Bainum, Peter M.↗

NASA NTRS1991

The P1-RKDG method for two-dimensional Euler equations of gas dynamics

A class of nonlinearly stable Runge-Kutta local projection discontinuous Galerkin (RKDG) finite element methods for conservation laws is investigated. Two dimensional Euler equations for gas dynamics are solved using P1 elements. The generalization of the local projections, which for scalar nonlinear conservation laws was designed to satisfy a local maximum principle, to systems of conservation laws such as the Euler equations of gas dynamics using local characteristic decompositions is discussed. Numerical examples include the standard regular shock reflection problem, the forward facing step problem, and the double Mach reflection problem. These preliminary numerical examples are chosen to show the capacity of the approach to obtain nonlinearly stable results comparable with the modern nonoscillatory finite difference methods.

Cockburn, Bernardo↗

NASA NTRS1991

Numerical aspects of computing high Reynolds number flows on unstructured meshes

An edge-data structure describing a mesh edge-wise given the vertices of each edge and neighboring cell information is used developing algorithms for the Navier-Stokes equations on triangular meshes. Edge formulas for the Galerkin and finite-element discretization of gradient, divergence, Hessian, and Laplacian operators are derived. A simple edge formula is derived for the discretization of the Laplacian operator, where precise theoretical conditions for a discrete maximum principle can be ascertained. Practical issues associated with solving the Navier-Stokes equations on unstructured meshes are addressed, along with issues concerning the generation of highly stretched triangular meshes and the modeling of turbulence on unstructured meshes. A turbulence modeling strategy is proposed, and numerical results for a high-Reynolds-number flow about single- and multielement airfoils are discussed.

Barth, Timothy J.↗

NASA NTRS1991

Optimal interaction of indenter with inhomogeneous plate

Consideration is given to a new class of problems dealing with an optimal design of an inhomogeneous plate during dynamic penetration of the rigid indenter. The quality criterion of the process is defined by the specific mass of the target, which absorbs the given kinetic mass of the indenter. Parameters of control are expressed in terms of mechanical characteristics, i.e., distribution of density and the related hardness across the plate thickness. The maximum principle of Pontryagin is used to search for the piecewise continuous control function. With consideration of impact conditions and characteristics for a given class of material, an optimal target structure criterion was estimated for engineering applications.

Aptukov, Valery N.↗

NASA NTRS1990

An improved shooting method for solving minimum-time maneuver problems

The minimum-time attitude maneuvers of a rigid spacecraft are considered. Generally, the associated nonsingular, nonlinear two-point boundary-value problem, derived by using Pontryagin's Maximum Principle, can be solved through shooting methods to find the switching times for the bang-bang control. However, a good initial guess for the missing initial costates is important because the convergence range of the initial costates is very narrow, especially when a multi-bang-bang control strategy is needed. This paper proposes a numerical approach to generate the initial costates so that they are very close to the converged values. The initial costates are first generated by using a recently developed quasi-linearization technique for the near-minimum-time problem and then reduced in magnitude, through some properly designed scales, before the shooting method is used. Numerical examples indicate the closeness of the results from these two techniques (quasi-linearization and shooting).

Li, Feiyue↗

NASA NTRS1992

Optimal control computer programs

The solution of the optimal control problem, even with low order dynamical systems, can usually strain the analytical ability of most engineers. The understanding of this subject matter, therefore, would be greatly enhanced if a software package existed that could simulate simple generic problems. Surprisingly, despite a great abundance of commercially available control software, few, if any, address the part of optimal control in its most generic form. The purpose of this paper is, therefore, to present a simple computer program that will perform simulations of optimal control problems that arise from the first necessary condition and the Pontryagin's maximum principle.

Kuo, F.↗

NASA NTRS1994

A combined algorithm for minimum time slewing of flexible spacecraft

The use of Pontryagin's Maximum Principle for the large-angle slewing of large flexible structures usually results in the so-called two-point boundary-value problem (TPBVP), in which many requirements (e.g., minimum time, small flexible amplitude, and limited control powers, etc.) must be satisfied simultaneously. The successful solution of this problem depends largely on the use of an efficient numerical computational algorithm. There are many candidate algorithms available for his problem (e.g., quasilinearization, gradient, and shooting, etc.). In this paper, a proposed algorithm, which combines the quasilinearization method with a time shortening technique and a shooting method, is applied to the minimum-time, three-dimensional, and large-angle maneuver of flexible spacecraft, particularly the orbiting Spacecraft Control Laboratory Experiment (SCOLE) configuration. Theoretically, the nonlinear TPBVP can be solved only through the shooting method to find the 'exact' switching times for the bang-bang controls. However, computationally, a suitable guess for the missing initial costates is crucial because the convergence range of the unknown initial costates is usually narrow, especially for systems with high dimensions and when a multi-bang-bang control strategy is needed. On the other hand, the problems of near minimum time attitude maneuver of general rigid spacecraft and fast slewing of flexible spacecraft have been examined by the authors through a numerical approach based on the quasilinearization algorithm with a time shortening technique. Computational results have demonstrated its broad convergence range and insensitivity to initial costate choices. Consequently, a combined approach is naturally suggested here to solve the minimum time slewing problem. That is, in the computational process, the quasilinearization method is used first to obtain a near minimum time solution. Then, the acquired converged initial costates from the quasilinearization approach are transformed (tailored) to and used as the initial costate guess for starting the shooting method. Finally, the shooting method takes over the remaining calculations until the minimum-time solution converges. The nonlinear equations of motion of the SCOLE are formulated by using Lagrange's equations, with the mast modeled as a continuous beam subject to three-dimensional deformations. The numerical results will be presented and some related computational issues will also be discussed.

Bainum, P. M.↗