Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MOF”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Development and Test Evaluations for Ni-DOBDC Metal Organic Framework (MOF) Engineered Forms

A joint effort to prepare engineered forms of a Ni-DOBDC metal organic framework (MOF) was completed with contributions from PNNL, SNL and the INL. Two independent methods were used at INL and SNL to prepare engineered form (EF) sorbents from Ni-DOBDC MOF powder developed and prepared at PNNL. Xe and Kr capacity test evaluations were performed at ambient temperature with the cryostat experimental setup at INL. The initial INL EF MOF test results indicated a Xe capacity of 1.6 mmol/kg sorbent and no Kr capacity. A large loss of surface area also occurred during minimal testing rendering the INL EF MOF unusable. Four capacity tests were completed using the SNL EF MOF at ambient temperature and resulted in Xe capacities of 1.4, 4.2, 5.0 and 3.8 mmol/kg sorbent with no Kr capacity observed in any ambient temperature tests. Two additional capacity tests were performed at 240 K to further evaluate SNL EF MOF performance. Xe capacities of 50.7 and 49.3 mmol/kg of sorbent and Kr capacities of 0.77 and 0.69 mmol/kg of sorbent were obtained, respectively. Following the adsorption evaluations, the SNL EF MOF material had lost about 40 % of the initial mass and 40 % of the initial surface area. In general, the Xe capacity results at ambient temperature for the INL and SNL EF Ni-DOBDC MOF’s were lower than 9.8 mmol Xe/kg sorbent test results reported by INL in FY-12 using PNNL’s inital EF supplied material.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Post synthetic amine functionalization of MOF-808 for CO 2 sorption via ligand exchange and Michael addition

Post synthetic modification of metal organic frameworks presents a viable route for amine functionalization which can significantly enhance CO 2 sorption capacity. We present a facile means of amine incorporation using limited synthetic steps and low-cost reagents that results in a high density of primary alkyl amines distributed through a zirconium-based metal organic framework (MOF). Both the MOF synthesis and the post synthetic modification take place under aqueous conditions and result in strongly bound molecular amines available for sorbate interaction throughout the MOF pores. Furthermore, this amine incorporation protocol results in a significantly increased CO 2 capacity compared with the unmodified MOF-808. Specifically, CO 2 isotherms collected at 298 K for the unmodified MOF-808 show uptakes of 0.06, 0.2, and 1.2 mmol/g at 4, 15, and 100 kPa, respectively, which can be compared with 0.3, 0.7, and 2.5 mmol/g for the glycine grafted MOF-808 and 0.5, 0.9, and 2.3 mmol/g for ethylenediamine grafted MOF-808.

Amine sorbent↗

Densification Pressure Optimization of MOF-808-Based Membranes for Lithium Metal Batteries

The use of metal–organic frameworks (MOFs) in hybrid electrolytes for lithium (Li) metal batteries has grown in prominence in recent years, primarily due to the chemical tunability of the MOF’s pore structures, which can directly influence Li–ion transport properties. The most attractive form factor for a MOF electrolyte is a thin, flexible membrane, which requires the application of pressure to increase the contact between the MOF particles. Herein, a systematic study of the influence of pressure on the properties of MOF-808-based membranes is presented. It is shown that when a dry, roll-pressed membrane is subjected to pressure ≥120 MPa, a total loss of crystallinity and a significant loss of porosity is observed. Alternatively, a slurry-cast membrane, compressed under controlled pressures, can maintain crystallinity and porosity while decreasing the interparticle void space. Interesting, the conductivity of the membranes infiltrated with liquid electrolyte is not greatly affected by the pressure applied, though ultimately it is shown that for cycling with Li metal, compressed membranes with compact particles are preferred. In conclusion, this study highlights the critical importance of controlling the pressure applied to MOF-based membranes during fabrication and during cell assembly and lays out the foundation for further investigation of how to optimize membrane fabrication for hybrid electrolytes that use MOFs as the dominate component.

25 ENERGY STORAGE↗

Design and Synthesis of Novel Porous Metal-Organic Frameworks (MOFs) Toward High Hydrogen Storage Capacity

Statement of Objectives: 1. Synthesize viable porous MOFs for high H2 storage at ambient conditions to be assessed by measuring H2 uptake. 2. Develop a better understanding of the operative interactions of the sorbed H2 with the organic and inorganic constituents of the sorbent MOF by means of inelastic neutron scattering (INS, to characterize the H2-MOF interactions) and computational studies (to interpret the data and predict novel materials suitable for high H2 uptake at moderate temperatures and relatively low pressures). 3. Synergistically combine the outcomes of objectives 1 and 2 to construct a made-to-order inexpensive MOF that is suitable for super H2 storage and meets the DOE targets - 6% H2 per weight (2kWh/kg) by 2010 and 9% H2 per weight (3kWh/kg) by 2015. The ongoing research is a collaborative experimental and computational effort focused on assessing H2 storage and interactions with pre-selected metal-organic frameworks (MOFs) and zeolite-like MOFs (ZMOFs), with the eventual goal of synthesizing made-to-order high H2 storage materials to achieve the DOE targets for mobile applications. We proposed in this funded research to increase the amount of H2 uptake, as well as tune the interactions (i.e. isosteric heats of adsorption), by targeting readily tunable MOFs:

08 HYDROGEN↗

Photoexcitation of Fe 3 O Nodes in MOF Drives Water Oxidation at pH=1 When Ru Catalyst Is Present

Abstract Artificial photosynthesis strives to convert the energy of sunlight into sustainable, eco‐friendly solar fuels. However, systems with light‐driven water oxidation reaction (WOR) at pH=1 are rare. Broadly used [Ru(bpy) 3 ] 2+ (bpy=2,2’‐bipyridine) photosensitizer has a fixed +1.23 V potential which is insufficient to drive most water oxidation catalysts (WOCs) in acid, while Fe 2 O 3 , featuring the highly oxidizing holes, is not stable at low pH. Here, the key examples of Fe‐based metal–organic framework (MOF) water oxidation photoelectrocatalysts active at pH=1 are presented. Fe‐MIL‐126 and Fe MOF‐dcbpy structures were formed with 4,4’‐biphenyl dicarboxylate (bpdc), 2,2’‐bipyridine‐5,5’‐dicarboxylate (dcbpy) linkers and their mixtures. Presence of dcbpy linkers allows integration of metal‐based catalysts via coordination to 2,2’‐bipyridine fragments. Fe‐based MOFs were doped with Ru‐based precursors to achieve highly active MOFs bearing [Ru(bpy)(dcbpy)(H 2 O) 2 ] 2+ WOC. Materials were analyzed with X‐ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infra‐red (FTIR) spectroscopy, resonance Raman, X‐ray absorption spectroscopy, fs optical pump‐probe, electron paramagnetic resonance (EPR), diffuse reflectance and electric conductivity measurements and were modeled by band structure calculations. It is shown that under reaction conditions, Fe III and Ru III oxidation states are present, indicating rate‐limiting electron transfer in MOF. Fe 3 O nodes emerge as photosensitizers able to drive prolonged O 2 evolution in acid. Further developments are possible via MOF's linker modification for enhanced light absorption, electrical conductivity, reduced MOF solubility in acid, Ru‐WOC modification for faster WOC catalysis, or Ru‐WOC substitution to 3d metal‐based systems. The findings give further insight for development of light‐driven water splitting systems based on Earth‐abundant metals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Revisiting Competitive Adsorption of Small Molecules in the Metal–Organic Framework Ni-MOF-74

To precisely evaluate the potential of metal-organic frameworks (MOFs) for gas separation and purification applications, it is crucial to understand how various molecules competitively adsorb inside MOFs. In this paper, we combine in situ infrared spectroscopy with ab initio calculations to investigate the mechanisms associated with co-adsorption of a number of small molecules including CO, NO, and CO 2 inside the prototypical framework Ni-MOF-74. Surprisingly, we find that the displacement of CO bound inside Ni-MOF-74 (binding energy of 53 kJ/mol) is readily driven by CO 2 exposure, even though CO 2 has a noticeably weaker binding energy of only 41 kJ/mol; meanwhile, the significantly more strongly binding NO molecule (90 kJ/mol) is not able to easily displace bound CO inside Ni-MOF74. These results show that single-phase binding energies of a molecule inside the MOF cannot completely describe their interaction with the MOF in the presence of other guest molecules. Here, we unveil a number of crucial factors such as the kinetic barrier, partial pressure, secondary binding sites, and guest-host/lateral interactions that control the co-adsorption process and combined with the binding energy are better descriptors of the behavior and adsorption of gas mixtures inside MOFs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Photochemical CO 2 Reduction by a Postsynthetically Modified Zr-MOF

Metal–organic frameworks are an excellent platform for photochemical CO 2 reduction into valuable chemicals. Herein, we report the synthesis and photocatalytic behavior of Ru@MOF-808, a Zr-based MOF, modified with a Ru-polypyridyl complex. The postsynthetic modification was achieved using solvent-assisted incorporation of bipyridine–carboxylate ligands onto the nodes of the MOF-808, followed by the coordination of Ru­(II)-terpyridine moiety. A thorough characterization including 1 H NMR, diffuse reflectance UV/vis, X-ray absorption spectroscopy and gas adsorption studies, combined with DFT calculations, provides strong support for efficient incorporation of the molecular Ru-complex at the loading of one Ru center per node. In the presence of a strong sacrificial reductant BIH, Ru@MOF-808 was found to catalyze the photochemical reduction of CO 2 into a mixture of CO and formate ion. When compared to the homogeneous model catalyst Ru­(tpy)­(bpy) 2+ , Ru@MOF-808 was found to exhibit higher formate yields. Additionally, to explain these formate enhancements, we propose a mechanism that involves CO 2 capture at the MOF nodes to form Zr-bicarbonate species, which further react in a hydride transfer reaction with photogenerated Ru–H donor, thereby outperforming molecular catalysts in HCOO – production. Overall, the results presented in this work indicate the potential of Zr-based MOFs in integrating CO 2 capture with its photochemical conversion to desired products.

CO2 reduction↗

Boosting Photoelectric Conductivity in Porphyrin-Based MOFs Incorporating C 60

Electronic structure calculations show that guest C60 in the porphyrin-containing metal organic frameworks Zn 2 (TCPB)(DA-ZnP) (DA-MOF; H 4 TCPB = 1,2,4,5-tetrakis(4-carboxyphenyl)benzene, DA-ZnP = [5,15-bis[(4-pyridyl)ethynyl]-10,20-diphenylporphinato]zinc(II)) and Zn 2 (TCPB)(F-ZnP) (F-MOF; F-ZnP = [5,15-di(4-pyridyl)-10,20-bis(pentafluorophenyl)porphinato]zinc(II)) engenders high photoelectrical conductivity due to efficient donor–acceptor charge-transfer (CT) interactions. Structural modifications at the meso position of the porphyrin influence the preferred positions of C 60 within the frameworks, giving rise to host–guest interactions with different anisotropic structural, electronic, and optoelectronic properties. A preferred slipped-parallel π-stacked interaction of C 60 that is predicted for NH 2 -substituted DA-MOF and F-MOF fosters strong CT transitions and lowers band gaps by ~1.0 eV compared to the pristine DA-MOF and F-MOF. Hopping rates computed using Marcus theory are found to be anisotropic and accelerated by multiple orders of magnitude across π-stacked interfaces created by C 60 incorporation, a consequence of strong electronic coupling between initial and final diabatic states. Calculations indicate that photoinduced electron transfer, as well as direct CT from porphyrin to C 60 upon irradiation, triggers a charge separation process that leads to the formation of what should be long-lived electron-trapped states at the heterojunctions. Lastly, design principles revealed here for the control of photophysical and electron-transfer processes will be useful for constructing new MOF-derived visible- and infrared-based optoelectronics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Facile Fabrication of Hierarchical MOF–Metal Nanoparticle Tandem Catalysts for the Synthesis of Bioactive Molecules

Multifunctional metal–organic frameworks (MOFs) that possess permanent porosity are promising catalysts in organic transformation. Herein, we report the construction of a hierarchical MOF functionalized with basic aliphatic amine groups and polyvinylpyrrolidone-capped platinum nanoparticles (Pt NPs). The postsynthetic covalent modification of organic ligands increases basic site density in the MOF and simultaneously introduces mesopores to create a hierarchically porous structure. The multifunctional MOF is capable of catalyzing a sequential Knoevenagel condensation–hydrogenation–intramolecular cyclization reaction. The unique selective reduction of the nitro group to intermediate hydroxylamine by Pt NPs supported on MOF followed by intramolecular cyclization with a cyano group affords an excellent yield (up to 92%) to the uncommon quinoline N-oxides over quinolines. The hierarchical MOF and polyvinylpyrrolidone capping agent on Pt NPs synergistically facilitate the enrichment of substrates and thus lead to high activity in the reduction–intramolecular cyclization reaction. The bioactivity assay indicates that the synthesized quinoline N-oxides evidently inhibit the proliferation of lung cancer cells. Finally, our findings demonstrate the feasibility of MOF-catalyzed direct synthesis of bioactive molecules from readily available compounds under mild conditions.

36 MATERIALS SCIENCE↗

Exceptional NH 3 Detection by Cu(cyhdc) MOF Sensor Due to H 2 O Coadsorption

Metal–organic framework (MOF)-based electrical impedance sensors are a growing class of sensors that show utility in the detection of environmentally toxic gases. Detection of trace NH 3 has been particularly difficult to design due to the low electrical response of NH 3 . However, this has been circumvented by judiciously selecting a MOF that has enhanced electrical response to NH 3 due to coadsorption with predominant atmospheric gases such as water. Herein, an MOF Cu(cyhdc) based sensor has been successfully demonstrated for the enhanced detection of environmentally toxic NH 3 gas. The sensor shows a change in impedance when it is exposed to 5 ppm of NH 3 . At 20 °C, >30% relative humidity (RH) is necessary to elicit a change, with the response increasing with RH and reaching 3170× at 92% RH, producing the largest published response to NH 3 for a MOF direct electrical sensor. In the absence of water, no change is observed toward 5 ppm of NH 3 over 20–50 °C. Here, this electrical response is largely driven by huge decreases in the imaginary component of the impedance, attributed to increased capacitance at the surface of the MOF crystallites upon NH 3 and H 2 O coadsorption. Complementary structural and microstructural characterization proves that the Cu(cyhdc) crystalline structure and morphology remain intact under trace NH 3 and/or H 2 O adsorption. Despite extremely low NH 3 , loadings seen in TGA, XPS, and FT-IR confirm NH 3 and H 2 O adsorption, and changes to the metal-carboxylate IR peak positions are observed upon NH 3 adsorption. Concentrated primarily at the outer surfaces of the MOF crystallites, this NH 3 and H 2 O coadsorption effectively increases the surface capacitance across the Cu(cyhdc) powder and enables direct electrical detection of trace NH 3 . Together, these results demonstrate how coadsorption of specific molecules (H 2 O) can be used to enable the electrical detection of trace toxic gases that would otherwise not have produced a MOF sensor response.

ammonia↗

Linker Installation: Engineering Pore Environment with Precisely Placed Functionalities in Zirconium MOFs

Precise placement of multiple functional groups in a highly ordered metal–organic framework (MOF) platform allows the tailoring of the pore environment, which is required for advanced applications. To realize this, we present a comprehensive study on the linker installation method, in which a stable MOF with coordinatively unsaturated Zr 6 clusters was employed and linkers bearing different functional groups were postsynthetically installed. Specifically, a Zr-MOF with inherent missing linker sites, namely, PCN-700, was initially constructed under kinetic control. Twelve linkers with different substituents were then designed to study their effect on MOF formation kinetics and therefore resulting MOF structures. Guided by the geometrical analysis, linkers with different lengths were installed into a parent PCN-700, giving rise to 11 new MOFs and each bearing up to three different functional groups in predefined positions. Systematic variation of the pore volume and decoration of pore environment were realized by linker installation, which resulted in synergistic effects including an enhancement of H2 adsorption capacities of up to 57%. In addition, a size-selective catalytic system for aerobic alcohol oxidation reaction is built in PCN-700 through linker installation, which shows high activity and tunable size selectivity. Altogether, these results exemplify the capability of the linker installation method in the pore environment engineering of stable MOFs with multiple functional groups, giving an unparalleled level of control.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Wavelength-Dependent Energy and Charge Transfer in MOF: A Step toward Artificial Porous Light-Harvesting System

Chromophore assemblies within well-defined porous coordination polymers, such as metal–organic frameworks (MOFs), can emulate the functionality of the antenna rings of chlorophylls in light-harvesting complexes (LHCs). The chemical, electronic, and structural diversities define MOFs as a promising platform where photogenerated excitons can be displaced to redox catalysts similar to the reaction center of the LHC. The precise positioning of the pigments and complementary redox units enables us to understand the charge/energy-transfer process within these crystalline solid compositions. In this study, we postsynthetically anchored tetraphenylporphyrinato zinc(II) (TPPZn)-derived complementary pigment within the 1D pores of 1,3,6,8-tetrakis(p-benzoicacid)pyrene (H4TBAPy)-derived NU-1000 MOF to form a high-density donor–acceptor system. The ground- and excited-state redox potentials of the donor and acceptor were chosen to facilitate an energy transfer (EnT) from the excited MOF (i.e., NU-1000*) to TPPZn and a charge transfer (CT) from excited porphyrin (i.e., TPPZn*). Thus, the processes depend on the excitation wavelength. The energy transfer process was spectroscopically probed by excitation–emission mapping: MOF emission was completely quenched at 460 nm, where the pyrene-centered emission was expected. Instead, the excited MOF efficiently transfers the energy to manifest a TPPZn-centered emission at 670 nm (k EnT ≈ 4.7 × 10 11 s–1). The excited TPPZn pigment, with a neighboring TBAPy linker, forms an artificial “special-pair”-like system driving the charge-separation process (k CT = 1.2 × 10 10 s –1 ). The findings demonstrate a synthetic MOF-based artificial LHC system where their well-defined structure will open up new possibilities as the separated charge can hop along the 1D pore channel for further mechanistic understanding and future developments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Presentation of gas-phase-reactant-accessible single-rhodium-atom catalysts for CO oxidation, via MOF confinement of an Anderson polyoxometalate

Geometric or electronic confinement of guests within nanoporous hosts holds promise for imparting catalytic functionality, including single-metal-atom catalytic functionality, to existing materials. When the nanoporous host is a metal–organic framework (MOF), single-metal-ion catalysts have typically been installed by grafting to an open site on an inorganic node, with the node effectively becoming the support for the catalyst. This approach, however, imposes compositional constraints, as the node not only needs to be receptive to grafting, but also must be capable of stabilizing the framework against solvent evacuation, chemical exposure, and heating. Here, we show that disk-like, Anderson polyoxometalate clusters (RhMo 6 O 24 n- and Mo 7 O 24 m- ; POMs) can be confined in pore-specific and orientation-specific fashion within the hierarchically porous, Zr(IV)-based MOF, NU1K. Self-limiting loading of one cluster per pore, and associated nano-confinement, serve to isolate each POM and prevent consolidation caused by sintering. Additionally, the oriented confinement serves to expose individual rhodium atoms to candidate gas-phase reactants, while enabling the rhodium atom to employ a well-defined oxy-molybdenum cluster, rather than a MOF node, as a support. Synchrotron-based difference-electron-density maps and differential pair-distribution-function analyses of scattered X-rays establish cluster siting and orientation and confirm isolation. Nanoconfined (i.e., MOF- and POM-confined) single-rhodium(III)-atoms are catalytically competent for an illustrative gas-phase reaction, CO oxidation by O 2 , with the MOF-isolated POM enormously outperforming nonporous, MOF-free, solid (NH 4 ) 3 [H 6 RhMo 6 O 24 ]·6H 2 O. This paper highlights the value of MOF-based nano-confinement and oriented isolation of planar POMs as a means of uniformly presenting and stabilizing potent single-metal-atom catalysts, in reactant-accessible form, on well-defined supports.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structural reversibility of Cu doped NU-1000 MOFs under hydrogenation conditions

The metal-organic framework (MOF), NU-1000, and its metalated counterparts have found proof-of-concept application in heterogeneous catalysis and hydrogen storage amongst others. A vapor-phase technique, akin to atomic layer deposition (ALD), is used to selectively deposit divalent Cu ions on oxo, hydroxo-bridged hexa-zirconium(IV) nodes capped with terminal –OH and -OH 2 ligands. Subsequent reaction with steam yields node-anchored, CuII-oxo,hydroxo clusters. We find that cluster installation via AIM (= ALD In MOFs) is accompanied by an expansion of MOF mesopore (channel) diameter . We investigated the behavior of the cluster-modified material, termed Cu-AIM-NU-1000, to heat treatment up to 325 °C, at atmospheric pressure with a low flow of H2 into the reaction cell. The response under these conditions revealed two important results: (1) Above 200 °C, the initially installed few-metal-ion clusters reduce to neutral Cu atoms. The neutral atoms migrate from the nodes and aggregate into Cu nanoparticles. While the size of particles formed in the MOF interior is constrained by the width of mesopores (ca. 3 nm), those formed on the exterior surface of the MOF can grow as large as ca. 8 nm. (2) Reduction and release of Cu atoms from the MOFs nodes is accompanied NU-1000 undergoes dynamic structural transformation as it reverts back to its original dimension following the release. These results show while the MOF framework itself remains intact at 325 °C in an H 2 atmosphere, the small, AIM-installed Cu II -oxo,hydroxo clusters are stable with respect to reduction and conversion to metallic nanoparticles only up to ~200 °C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Colorometric detection of water using MOF-polymer films and composites

A method including exposing a mixture of a porous metal organic framework (MOF) and a polymer to a predetermined molecular species, wherein the MOF has an open metal site for the predetermined molecular species and the polymer has a porosity for the predetermined molecular species; and detecting a color change of the MOF in the presence of the predetermined molecular species. A method including combining a porous metal organic framework (MOF) and a polymer, wherein the MOF has an open metal site for a predetermined molecular species and the polymer has a porosity for the predetermined molecular species. An article of manufacture including a mixture of a porous metal organic framework (MOF) and a polymer, wherein the MOF has an open metal site for a predetermined molecular species and the polymer has a porosity for the predetermined molecular species.

36 MATERIALS SCIENCE↗

Vapor Phase Installation of CpCo(CO) 2 in MOF‐808

Metal-organic frameworks (MOFs), including MOF-808 present an opportunity for vapor phase installation of reactive centers that may serve as uniform sites for precision catalysis. The mechanism of cobalt installation in MOF-808 through atomic layer deposition (ALD) upon CpCo(CO )2 exposure is investigated through in situ FTIR spectroscopy complemented by density functional theory modeling. The role of subsequent H 2 O exposure in the hydrolysis of carbonyl and cyclopentadienyl ligands to complete the installation is also investigated. In situ FTIR study reveals that upon exposure of CpCo(CO) 2 to MOF-808 at 115 °C, a long-lived, stable intermediate is formed that presents carbonyl stretching vibrations similar to the undissociated precursor that are attributed to multiple chemisorbed carbonyl complexes. In MOF-808, cobalt species are initially absorbed near the BTC linker rather than directly on the nodes, revealing the importance of non-covalent interactions in the installation process. DFT suggests that H 2 O exposure promotes carbonyl elimination but leaves a cyclopentadienyl-capped cobalt that is more stable than the complete hydrolysis product. The simulations are consistent with cobalt installation in MOF-808 using CpCo(CO) 2 and H 2 O at 115 °C and further consistent with the lack of ALD thin film deposition of cobalt oxide thin films on planar supports.

36 MATERIALS SCIENCE↗

Reticular chemistry in the rational synthesis of functional zirconium cluster-based MOFs

In the past two decades, reticular chemistry has developed into a powerful tool for the design and synthesis of porous, crystalline framework materials. The discovery of the first hexanuclear, zirconium cluster-based MOF (i.e. UiO-66; fcu net) led to a vast library of functional Zr-MOFs with various properties. The versatile connectivity of zirconium hexanuclear clusters and the adaptable tunability of organic ligands have resulted in the rational synthesis of a large set of Zr-MOFs based on edge-transitive nets; these nets commonly exists in crystalline network structures as suggested by reticular chemistry. In this review, we summarize recent advances in the synthesis of zirconium cluster-based MOFs in the light of reticular chemistry design principles. Isoreticular tuning of MOF parent structures and post-synthetic modification of Zr-MOFs for targeted applications are also deliberated.

Reticular chemistry↗

Modulating Cu electrode microenvironments with MOF coatings: insights from molecular dynamics and electrochemical experiments of CO reduction

Metal-organic frameworks (MOFs) present a compelling strategy for tuning electrochemical interfaces by reshaping interfacial solvent structure. In this study, we examine how MOF coatings influence the microenvironment at copper electrodes during the CO electroreduction reaction (CORR) using a combined approach of molecular dynamics (MD) simulations and electrochemical experiments. Two MOFs, NU-901 and ZIF-8, are selected to explore the impact of pore size and channel hydrophobicity on electrochemical activity and interfacial concentration in acetonitrile (ACN) and dimethyl sulfoxide (DMSO) electrolytes. Electrochemical measurements reveal that MOF@Cu electrodes exhibit lower Faradaic efficiencies for CO hydrogenation products (ethylene and methane) compared to bare copper but have dramatic impacts on the interfacial microenvironment. NU-901, with its larger pores and strong interactions with DMSO, traps DMSO molecules and enhances CO coordination in DMSO but suppresses CORR selectivity in favor of the hydrogen evolution reaction (HER). ZIF-8, with smaller pores and hydrophobic channels, limits the interfacial water concentration, and, in ACN, promotes CO coordination. The simulations provide insights into how MOFs can act as physical modulators of reactant delivery and interfacial structure to control electrochemical microenvironments. This work highlights the value of molecular dynamics in uncovering how structural features of MOFs influence interfacial phenomena, even when catalytic performance is not directly improved.

Copper electrode microenvironments↗