Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MHZ RANGE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Post-flare effects in the lower ionosphere of middle latitudes

Beginning in the 1960s, records were made of noise from the region around the Polar Star on 29 MHz (Krivsky and Tlamicha, 1960) at the Ondrejov Observatory near Prague. Since the aerial characteristic was not too narrow, radio bursts were received of solar origin (of flares) at the noise level, SCNA effects (sudden cosmic noise absorption) at the time of intensive flare X-emission and in some rare cases, after large proton flares, small absorption effects of a few hours duration (Krivsky, 1969). These post-flare absorption effects in cosmic noise are evidently analogous with PCA effects (polar cap absorption) and are connected with ionospheric absorption of radio cosmic noise, caused by fast particles of subcosmic radiation. The recording of long term absorption effects after large particle flares at European midlatitudes was reported at the beginning of the 1960s. It was then usual to record radio cosmic noise with riometers at frequencies of about 18 MHz in the polar or subpolar regions in an effort to record PCA effects of subcosmic radiation (Hakura, 1968). An attempt was made to record the complex of emissions mentioned as well as the effects in a new frequency range (30 MHz), which did not agree with the ideas of the contemporaneous representatives of the Ionospheric Department of the Geophysical Institute in Prague. In recent years radio cosmic noise has been recorded at the Upice Observatory. These long term after flare effects of cosmic radio noise absorption (AF-CNA) at middle latitudes are reported to the geophysical and ionospheric community for the first time.

Krivsky, L.↗
DOE OSTI2025

Single-element balanced detector giving 65 dB CMRR at 30 MHz

We present a simple design for a single-element balanced detector (BD) that utilizes optical fibers in the sensing and reference channels with path length differences set to detect the differential signal at a desired frequency. With this approach, we easily achieve a common-mode rejection ratio of 65 dB, corresponding to the shot-noise limit of our setup. The CMRR demonstration is made in the MHz frequency range but could be extended to the kHz or GHz range. Using a single detector, the BD achieves stable CMRR over extended periods and does not require careful matching of detectors and amplification electronics. We demonstrate the single-element balanced detector design using the optical Kerr effect induced by a 30 MHz pulsed laser, showing a significant improvement over similar experiments using a commercial balanced detector.

Badilla-Nunez, Kelly [Georgia Institute of Technol↗
NASA NTRS1993

Liquid metal drop ejection

The aim of this project was to demonstrate the possibility of ejecting liquid metals using drop on demand printing technology. The plan was to make transducers for operation in the 100 MHz frequency range and to use these transducers to demonstrate the ability to eject drops of liquid metals such as gallium. Two transducers were made by indium bonding piezoelectric lithium niobate to quartz buffer rods. The lithium niobate plates were thinned by mechanical polishing to a thickness of 37 microns for operation at 100 MHz. Hemispherical lenses were polished in the opposite ends of the buffer rods. The lenses, which focus the sound waves in the liquid metal, had an F-number equals 1. A mechanical housing was made to hold the transducers and to allow precise control over the liquid level above the lens. We started by demonstrating the ability to eject drops of water on demand. The drops of water had a diameter of 15 microns which corresponds to the wavelength of the sound wave in the water. A videotape of this ejection was made. We then used a mixture of Gallium and Indium (used to lower the melting temperature of the Gallium) to demonstrate the ejection of liquid metal drops. This proved to be difficult because of the oxide skin which forms on the surface of the liquid. In some instances, we were able to eject metal drops, however, this was not consistent and reproducible. An experiment was set up at NASA-Lewis to stabilize the process of drop on demand liquid metal ejection. The object was to place the transducer and liquid metal in a vacuum station so that no oxide would form on the surface. We were successful in demonstrating that liquid metals could be ejected on demand and that this technology could be used for making sheet metal in space.

Khuri-Yakub, B. T.↗
NASA NTRS1984

Radar echoes at 2.66 and 40.92 MHz from the mesosphere, part 2.6A

During recent decades, the ionospheric D region has been scanned extensively by radar in the frequency range from 1 to 60 MHz. Progress has been made in understanding the reflection/scattering of radio waves in that area. Rocket measurement of ion density irregularities were compared to radar echo observations at 2.75 MHz with the conclusion that the received radar signal was due to scattering from isotropic and homogeneous turbulence in the altitude region between 70 and 95 km. However, scattering cross sections at 2 and 6 mHz suggest that the radar echo from the region below 80 km is in part due to partial reflection from stratified layers. The VHF scattering cross section is aspect sensitive in the D region below about 75 km and tends to be isotropic at higher altitudes. Positive correlations between scattered signal power and signal correlation time (P/C) have been observed by VHF radars in the lower mesosphere, with the conclusion that it might be an additional indication of partial reflection from stratified layers. In the upper mesosphere where the P/C correlation is negative, it is generally believed that the scattering is caused by isotropic turbulence. Radar echoes at the 2.16 and 40.92 MHz ranges are compared, assuming that both result from turbulent scatter. Adjusting the radar Bragg wavelength, it was found that both sets are due to scattering from the same layer of turbulence-generated irregularities.

Royrvik, O.↗
NASA NTRS2010

ARCADE 2 Observations of Galactic Radio Emission

We use absolutely calibrated data from the Absolute Radiometer for Cosmology, Astrophysics, and Diffuse Emission (ARCADE 2) flight in July 2006 to model Galactic emission at frequencies 3, 8, and 10 GHz. The spatial structure in the data is consistent with a superposition of free-free and synchrotron emission. Emission with spatial morphology traced by the Haslam 408 MHz survey has spectral index beta_synch = -2.5 +/- 0.1, with free-free emission contributing 0.10 +/- 0.01 of the total Galactic plane emission in the lowest ARCADE 2 band at 3.15 GHz. We estimate the total Galactic emission toward the polar caps using either a simple plane-parallel model with csc|b| dependence or a model of high-latitude radio emission traced by the COBE/FIRAS map of CII emission. Both methods are consistent with a single power-law over the frequency range 22 MHz to 10 GHz, with total Galactic emission towards the north polar cap T_Gal = 0.498 +/- 0.028 K and spectral index beta = -2.55 +/- 0.03 at reference frequency 0.31 GHz. The well calibrated ARCADE 2 maps provide a new test for spinning dust emission, based on the integrated intensity of emission from the Galactic plane instead of cross-correlations with the thermal dust spatial morphology. The Galactic plane intensity measured by ARCADE 2 is fainter than predicted by models without spinning dust, and is consistent with spinning dust contributing 0.4 +/- 0.1 of the Galactic plane emission at 23 GHz.

Kogut, A.↗
DOE OSTI2022

The Tianlai dish array low-z surveys forecasts

Here, we present the science case for surveys with the Tianlai dish array interferometer tuned to the [1300, 1400] MHz frequency range. Starting from a realistic generation of mock visibility data according to the survey strategy, we reconstruct maps of the sky and perform foreground subtraction. We estimate the level of residuals from imperfect subtraction, mostly due to mode mixing, i.e. distortions in the reconstructed 3D maps due to frequency-dependent instrument response. We show that a survey of the North Celestial Polar cap during a year of observations, covering an area of 150 deg 2 , would reach a sensitivity of $1.5-2 mK per 1 MHz x 0.25 2 deg 2 voxel and be marginally impacted by mode mixing. Tianlai would be able to detect ~10 nearby massive H i clumps as well as a very strong cross-correlation signal of 21 cm intensity maps with the North Celestial Cap Survey optical galaxies. We also studied the performance of a mid-latitude survey, covering ~ 1500 deg 2 overlapping the SDSS footprint. Despite a higher noise level for the mid-latitude survey, as well as significant distortions due to mode mixing, Tianlai would be able to detect a highly significant cross-correlation between the 21 cm signal and the Sloan spectroscopic galaxy sample. Using the extragalactic signals measured from either or both of these surveys, and comparing them with simulations such as those presented here will make it possible to assess the impact of various instrumental imperfections on the Tianlai dish array performance. This would pave the way for future intensity mapping surveys with higher sensitivity.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Scalable phononic metamaterials: Tunable bandgap design and multi-scale experimental validation

Phononic metamaterials offer unprecedented control over wave propagation, making them essential for applications such as vibration isolation, waveguiding, and acoustic filtering. However, achieving scalable and precisely tunable bandgap properties across different length scales remains challenging. This study presents a user-friendly design framework for phononic metamaterials, enabling ultra-wide bandgap tunability (B/ω c ratios up to 172 %) across multiple frequency ranges and scales. Using finite element simulations of a Yablonovite-inspired unit cell, we establish a comprehensive parametric design space that illustrates how geometric parameters, such as sphere size and beam diameter, controls bandgap width and frequency. The scalability and robustness of the framework are validated through experimental testing on additively manufactured structures at both macro (10 mm) and micro (80 µm) scales, fabricated using Stereolithography and Two-Photon Polymerization. Transmission loss measurements, conducted with piezoelectric transducers and laser vibrometry, closely match simulations in the kHz and MHz frequency ranges, confirming the reliability and consistency of the bandgap behavior across scales. This work bridges theory and experiments at multiple scales, offering a practical methodology for the rapid design of phononic metamaterials and expanding their potential for diverse applications across a broad range of frequencies.

36 MATERIALS SCIENCE↗
NASA NTRS1990

Numerical simulation of solar wind density fluctuations and their effects on VLF radio interferometry

A mission consisting of an array of small satellites has been proposed to investigate radio sources at frequencies from approximately 2 to 20 MHz, a range unobservable from the ground because of ionospheric absorption and aberrations. Such a mission seems feasible and relatively inexpensive, but further investigation is still necessary. The solar wind is a major concern because it contains turbulence-induced random density variations that cause a fluctuating phase shift in any electromagnetic signal passing through, sometimes making radio source imaging by interferometry impossible. A numerical simulation has been developed which attempts to accurately characterize solar wind density fluctuations. Results have allowed more concrete conclusions to be drawn about observing constraints and have shown that interferometric imaging at radio frequencies below 10 MHz with baselines up to 100 km is possible at solar elongation angles of about 90 deg or more.

Williamson, Robert S., III↗
NASA NTRS1973

A new ion and electron detector for ion cyclotron resonance spectroscopy.

A new detector using an extremelly driven tuned circuit has been developed for use in ion cyclotron resonance spectroscopy experiments. Based on the Q-meter circuit, this detector will operate at frequencies greater than 1 MHz at rf levels less than 1 mV. Operation in the frequency range 1-15 MHz allows the use of higher magnetic fields for more efficient storage of low mass ions in the trapping mode of operation. In the frequency range 2-6 MHz electrons can be detected in the ion cyclotron resonance cell by their resonant motion in the trapping plane.

Huntress, W. T., Jr.↗
DOE OSTI2021

Development of NDE/NDT Tools for High-Volume & High-Speed Inspection of CFRP Structures in Automotive Manufacturing

Main advantages of the air-coupled ultrasound testing (ACUT) and electromagnetic testing (EMT) techniques for NDE of CFRP composites were non-contact sensing, scalability for high-speed inspection, cost-effectiveness, and non-hazardous operation. Despite these advantages, no systems that would satisfy the project requirements were commercially available. Hence, one of the major efforts of the Michigan State University (MSU) team at the initial stage of the project was to close this technological gap by developing, optimizing, and validating array sensors that would provide sufficient sensitivity, spatial coverage, and resolution for robust defect detection. Optimization of the ACUT and EMT sensor designs was performed using experimentally validated finite element models. Initial experiments using array probes were conducted on relatively flat CFRP samples. In parallel, the MSU team designed and assembled a portable platform with two robotic arms. The robots were equipped with newly designed sensors that enabled high-speed NDE of curved CFRP parts. Presently, the developed robotic platform can be used as a demo/template NDE system, which is easily adaptable to manufacturing environments and in-line NDE. The ACUT NDE system developed by the MSU team used a high-power 4-channel pulser receiver for parallel data acquisition. The array probes were designed by stacking commercially available ACUT transducers, which operated in the frequency range between 100 kHz and 500 kHz. MSU optimized the excitation procedure and developed wave focusing cones so as to reduce the crosstalk between the transducers and to provide higher pulse repletion frequency (PRF). The through-transmission (TT) and single-side access (SSA) inspection modes were successfully implemented. In the TT-ACUT, structural defects in CFRP were detected by passing ultrasonic waves through the test part. Hence, the ACUT transmitters and receivers needed to be placed on the opposite sides of the test part. In the SSA-ACUT, guided waves (GW) were excited in the test part using the transmitters and were sensed by the receivers from the same side. Multi-channel TT-ACUT and SSA-ACUT provided high-speed NDE, and were successfully validated on CFRP test samples with interlaminar delaminations and other embedded defects The EM techniques developed by the MSU team included: 1) eddy current testing (ECT), 2) capacitive imaging (CI) and hybrid dual-mode imaging. In ECT, structural damage was detected in CFRP using coils sensor arrays. In ECT, the excitation magnetic field is generated by passing an alternating current through a coil, which is placed above the test sample. The excitation field penetrates the conductive sample and induces the eddy currents in its transect. In turn, the eddy currents generate the reaction field, which affects the total field sensed by a coil. Hence, the presence of structural flaws will alter the eddy current flow and the picked-up signal. ECT is mostly sensitive to local changes of the electric conductivity of the test sample, and CFRPs are mostly conductive in the direction of carbon fibers. Hence, ECT was well suited for the detection of fiber damage/fiber irregularities. The MSU team developed printed circuit boards (PCB) with coil sensor arrays optimized for NDE of CFRP. Unlike most commercial probes designed for ECT of metallic structures, the MSU array probes were designed for operation in [1-10] MHz frequency range, which was optimal for low-conductive CFRP. Multiple sensing topologies (coil groups excitation/sensing arrangements) were implemented and successfully validated. Capacitive Imaging (CI) technique developed by MSU was complementary to ECT. In contrast to ECT, which was sensitive to local changes of the electrical conductivity, the CI was sensitive to local changes of the dielectric constant. Therefore, CI could provide information about matrix damage/matrix irregularities in CFRP. The MSU CI sensor arrays were made of multiple circular or rectangular open-plate capacitors printed on PCB. Sensors of this type are not commercially available. In addition to ECT and CI, the MSU team developed a hybrid (dual-mode) inductive/capacitive measurement technique that synergistically combined the benefits of inductive and capacitive sensing for rapid NDE of fiber reinforced polymer (FRP) composite structures. Fiber damage and fiber irregularities in FRPs were detected by configuring hybrid sensors as coil sensors. Similarly, matrix damage, matrix irregularities and interlaminar delaminations were detected by configuring hybrid sensors as capacitive sensors. ECT and CI were performed sequentially by means of electronic switching. Hence, eliminating the need for mounting two separate sensor arrays on the probe. Portable robotic platform was developed by MSU for multi-technique high-speed NDE of CFRP test parts. The platform had two 6-axis robots, which enabled inspection of curved parts in approximately a 6×6×6 ft 3 active scan area. On the software side, the MSU team integrated scripts for NDE hardware control with scripts for robot motion control. MSU also implemented automated path planning for the robots, reconstruction of part’s surfaces via stereovision, 3D rendering of inspection data, and image processing algorithms for enhanced defect detection. Automotive composite parts manufactured by Plasan Composites from Phase I were used to validate the ACUT and EMT techniques on representative testbeds. Among those parts were three X-braces for a Dodge Viper, one composite calibration plaque with known defects at known locations, and four other test sections, including sections from a front splitter, a corner section from a composite hood, and a high-pressure RTM panel made using non crimp fabric. Other test samples included CFRP and GFRP calibration plates with fiber/matrix defects fabricated at MSU/CVRC.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Radio Frequency Transients Correlated with Electron Flux Measured On-Board the STP-Sat6

We analyzed transient electromagnetic signatures, referred to as spacecraft environment discharges (SEDs) or on-board discharges (OBDs), and the in-situ particle environment simultaneously measured by the Radio Frequency Sensor (RFS) and the Space and Atmospheric Burst Reporting System Z-plasma spectrometer (SABRS-ZPS), respectively. These sensors are on-board the U.S. Department of Defense Space Test Program Satellite 6 (STP-Sat6) in geostationary orbit. Radio frequency signatures of SEDs on STP-Sat6 have relatively high peak amplitudes; they often caused amplitude-saturation in the so-called high band (120–140 MHz frequency range) of the RFS likely due to the proximity of their source to the RFS’s dipole antennas. We examined the occurrence rate of SEDs reported by the RFS and its temporal relationship to electron flux in the 7.9–12.2 keV range. Peaks in SED count rates were time-correlated with peaks in electron flux. The electron-flux peaks appeared to lead the SED count rate peaks by 24–45 min for the 7.9–12.2 keV energies. This indicates that incidence of electrons at this relatively low-energy range likely resulted in ramping up of the charging of the spacecraft leading to periods of high occurrence rates of discharges in and around the spacecraft.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Field-scale estimation of soil properties from spectral induced polarization tomography

Estimates of soil properties such as Cation Exchange Capacity (CEC), water content, grain size characteristics, and permeability are important in geotechnical engineering, water resources, and agriculture. We develop a non-intrusive approach to estimate these properties in the field using spectral induced polarization (SIP) tomography. This geophysical method provides information about the frequency dependence of the complex electrical conductivity of porous media. Using 18 soil samples collected from a Bordeaux vineyard, we first conducted a laboratory study using SIP over the frequency range 10 mHz-45 kHz. The laboratory data were used to confirm the accuracy of a recently developed dynamic Stern layer petrophysical model. The results are consistent with published values from previous works using soils. A comparison was made by comparing the field complex conductivity spectra and the experimental data at two locations where core samples were obtained. The model was then used in concert with field data to image the spatial distribution of CEC, water content, permeability, and mean grain size along a vineyard transect. For clay and sandy textures found in the field, measured and estimated CEC agree rather well (from 6 to 40% discrepancy). Furthermore, our approach provides an efficient way to estimate important soil properties in a non-invasive manner, in high resolution, and over field-relevant scales of the critical zone of the Earth.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Two-dimensional image edge enhancement using two orders of Bragg diffraction

The process of two-dimensional image edge enhancement with an acousto-optical spatial filter using two orders of light diffraction is studied. It is theoretically shown that the diffraction that occurs in a paratellurite crystal on a ‘slow’ acoustic wave propagating orthogonally to the optical axis of the crystal allows enhancing a two-dimensional edge of an image, transferred by optical radiation with a wavelength of 0.63 μm in a wide band of acoustic frequencies 25 – 50 MHz. Enhancement of a two-dimensional image edge at an acoustic frequency of 29 MHz is experimentally demonstrated. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Detection of the clock transition in thulium atoms by using repump laser radiation

A population transfer from the upper level of the clock transition in thulium atoms to the ground level is demonstrated by using radiation with a wavelength of 402 nm. The method for detecting the clock transition excitation that is not affected by technical fluctuations of the number of atoms in an optical lattice is investigated. The hyperfine splitting of the |4f{sup 12}({sup 3}F{sub 2})5d{sub 5/2} 6s{sup 2}; J = 7/2〉 level in the thulium atom is measured to be 1480(9) MHz. The suggested method for population transfer can be applied to both the hyperfine components of the clock transition intended for compensating Zeeman effect in a thulium optical clock. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Study of saturated-absorption resonances on the {sup 3}P{sub 0, 1, 2} – {sup 3}D{sub 1, 2, 3} transitions of magnesium atoms in a hollow-cathode discharge cell

The saturated-absorption resonances on the {sup 3}P{sub 0, 1, 2} – {sup 3}D{sub 1, 2, 3} transitions of magnesium atoms in a hollow-cathode discharge cell are studied. The line width (FWHM) for the observed saturated-absorption resonance on the 3{sup 3}P{sub 0} → 3{sup 3}D{sub 1} transition turns out to be ∼220 MHz. Experiments are performed using a system based on a 766-nm diode laser with amplification and frequency doubling in a nonlinear BiBO crystal. The results obtained are of interest for sub-Doppler cooling on the 3{sup 3}P{sub 2} → 3{sup 3}D{sub 3} transition. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Production of two-colour radiation with polarisations of components rotating in opposite directions

A method is proposed for the production of two-colour radiation with monochromatic components, the polarisation vectors of which rotate in opposite directions, and the rotation speed is controlled by the sound frequency. The method is based on acousto-optic (AO) interaction upon double passage of two-colour radiation through an AO cell made of a gyrotropic crystal; the method efficiency is demonstrated by the example of radiation from an Ar laser generating at wavelengths of 0.488 and 0.514 μm and an AO cell made of TeO{sub 2}, operating at a sound frequency of 60 MHz. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

The primordial black holes that disappeared: connections to dark matter and MHz-GHz gravitational Waves

In the post-LIGO era, there has been a lot of focus on primordial black holes (PBHs) heavier than ~10 15 g as potential dark matter (DM) candidates. We point out that the branch of the PBH family that disappeared — PBHs lighter than ~10 9 g that ostensibly Hawking evaporated away in the early Universe — also constitute an interesting frontier for DM physics. Hawking evaporation itself serves as a portal through which such PBHs can illuminate new physics, for example by emitting dark sector particles. Here, taking a simple DM scalar singlet model as a template, we compute the abundance and mass of PBHs that could have provided, by Hawking evaporation, the correct DM relic density. We consider two classes of such PBHs: those originating from curvature perturbations generated by inflation, and those originating from false vacuum collapse during a first-order phase transition. For PBHs of both origins we compute the gravitational wave (GW) signals emanating from their formation stage: from second-order effects in the case of curvature perturbations, and from sound waves in the case of phase transitions. The GW signals have peak frequencies in the MHz-GHz range typical of such light PBHs. We compute the strength of such GWs compatible with the observed DM relic density, and find that the GW signal morphology can in principle allow one to distinguish between the two PBH formation histories.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Measurements of DC SQUID Damping Effects on Superconducting Resonant Circuits

Here, we present experimental measurements of SQUID-induced damping effects on strongly coupled, lumped-element resonators in the 500kHz–1 MHz frequency range. While dc SQUIDs are commonly used for sensitive readout of electromagnetic signals such as in lumped-element axion dark matter searches, coupling a dc SQUID to a resonant circuit modifies the circuit's resonance frequency, quality factor, noise, and impedance. These parameters have a direct impact on the science reach of axion dark matter detectors, making it important to understand SQUID damping contributions. We describe a helium dip probe and two-stage SQUID readout scheme used to probe SQUID damping effects. Measurements from this setup inform the design and operation of both future test platforms as well as next-generation dark-matter experiments.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗