Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MASER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

The Zeeman effect in astrophysical water masers and the observation of strong magnetic fields in regions of star formation

The present study solves the transfer equations for the polarized radiation of astrophysical 22-GHz water masers in the presence of a magnetic field which causes a Zeeman splitting that is much smaller than the spectral line breadth. The emphasis is placed on the relationship between the recently detected circular polarization in this maser radiation and the strength of the magnetic field. When the observed spectral line breadth is smaller than about 0.8 km/s (FWHM), it is calculated that the uncertainty is less than a factor of about 2. The accuracy is improved significantly when the angle between the line of sight and the direction of the magnetic field does not exceed about 45 deg. Uncertainty in the strength of the magnetic field due to lack of knowledge about which hyperfine transition is the source of the 22-GHz masers is removed. The 22-GHz maser feature is found to be the result of a merger of the three strongest hyperfine components.

Nedoluha, Gerald E.↗
NASA NTRS1991

Ultra-stable performance of the superconducting cavity maser

Recent measurements on the superconducting cavity maser (SCM) oscillator show frequency stability of parts in 10 exp 15 for times from 1 to 1000 sec. Phase noise of approximately -80 dB/f-cubed was also measured. This short- and mid-term performance is believed to be better than that of any known microwave oscillator. In particular, stability at a measuring time of 1 sec is 10 times better than that of a hydrogen maser, and phase noise at 8 GHz is more than 20 dB below that of the best multiplied quartz crystal oscillators. Substantial technical improvements have been made to eliminate frequency instability due to operational parameters. They are temperature, pump frequency, pump power, pump frequency polarization, temperature gradient, coupling strength, and output VSWR. Either the parameter was stabilized or the coefficient which couples the parameter to the operating frequency was minimized. A frequency pulling coil has been implemented and tested to enable the SCM to be slaved to a hydrogen maser with a time constant of approximately 50 sec. This combination would allow the excellent long term performance of the hydrogen maser to be improved by the newly available short term performance of the SCM.

Dick, G. J.↗
NASA NTRS1992

Planar H2O masers in star-forming regions

The paper examines the planar geometry of shocked material, which is the key property in enabling the high brightness temperatures of H2O masers in star-forming regions. The brightness temperature, beaming angle, and the maser spot size are determined for thin, saturated planar masers under the assumption that the velocity change across the maser due to ordered motions is small compared with the thermal or microturbulent line width. For a given set of physical parameters, the brightness temperature is essentially fully determined by the length of the velocity-coherent region in the shocked plane along the line of sight. Effective aspect ratios (about 5-50) are found that are in agreement with values previously inferred from observed brightness temperatures.

Elitzur, Moshe↗
NASA NTRS1992

Astronomical masers

Recent research related to astronomical masers is reviewed. First, attention is given to phenomenology, including observations and modeling of galactic and extragalactic maser sources. The discussion then focuses on the developments concerning the physical properties of maser radiation. Finally, the use of masers as general tools for the study of astronomical environments where the radiation is produced and where it propagates, is discussed.

Elitzur, Moshe↗
NASA NTRS1993

A shock origin for interstellar H2O masers

We present a comprehensive model for the powerful H2O masers observed in starforming regions. In this model the masers occur behind dissociative shocks propagating in dense regions. This paper focuses on high-velocity dissociative shocks in which the heat of H2 reformation on dust grains maintains a large column of 300 - 400 K gas, where the chemistry drives a considerable fraction of the oxygen not in CO to form H2O. The H2O column densities, the hydrogen densities, and the warm temperatures produced by these shocks are sufficiently high to enable powerful maser action, where the maser is excited by thermal collisions with H atoms and H2 molecules. A critical ingredient in determining the shock structure is the magnetic pressure, and the fields required by our models are in agreement with recent observations. The observed brightness temperatures are the result of coherent velocity regions which have dimensions in the shock plane that are five to 50 times the postshock thickness.

Hollenbach, David↗
NASA NTRS1994

Water maser emission from X-ray-heated circumnuclear gas in active galaxies

We have modeled the physical and chemical conditions present within dense circumnuclear gas that is irradiated by X-rays from an active galactic nucleus. Over a wide range of X-ray fluxes and gas pressures, the effects of X-ray heating give rise to a molecular layer at temperatures of 400-1000 K within which the water abundance is large. The physical conditions within this molecular layer naturally give rise to collisionally pumped maser emission in the 6(sub 16) - 5(sub 23) 22 GHz transition of ortho-water, with predicted maser luminosities of 10(exp 2 +/- 0.5) solar luminosity per sq. pc of illuminated area. Given plausible assumptions about the geometry of the source and about the degree to which the maser emission is anisotropic, such surface luminosities are sufficient to explain the large apparent luminosities observed in water maser sources that are associated with active galactic nuclei.

Neufeld, David A.↗
NASA NTRS1994

Modeling of the hydrogen maser disk in MWC 349

Maser amplification in a Keplerian circumstellar disk seen edge on-the idea put forward by Gordon (1992), Martin-Pintado, & Serabyn (1992), and Thum, Martin-Pintado, & Bachiller (1992) to explain the millimeter hydrogen recombination lines in MWC 349-is further justified and developed here. The double-peaked (vs. possible triple-peaked) form of the observed spectra is explained by the reduced emission from the inner portion of the disk, the portion responsible for the central ('zero velocity') component of a triple-peaked spectrum. Radial gradient of electron density and/or free-free absorption within the disk are identified as the probable causes of this central 'hole' in the disk and of its opacity. We calculate a set of synthetic maser spectra radiated by a homogeneous Keplerian ring seen edge-on and compare them to the H30-alpha observations of Thum et al., averaged over about 1000 days. We used a simple graphical procedure to solve an inverse problem and deduced the probable values of some basic disk and maser parameters. We find that the maser is essentially unsaturated, and that the most probable values of electron temperature. Doppler width of the microturbulence, and electron density, all averaged along the amplification path are, correspondingly, T(sub e) less than or equal to 11,000 K, V(sub micro) less than or equal to 14 km/s, n(sub e) approx. = (3 +/- 2) x 10(exp 7)/cu cm. The model shows that radiation at every frequency within the spectrum arises in a monochromatic 'hot spot.' The maximum optical depth within the 'hot spot' producing radiation at the spectral peak maximum is tau(sub max) approx. = 6 +/- 1; the effective width of the masing ring is approx. = 0.4-0.7 times its outer diameter; the size of the 'hot spot' responsible for the radiation at the spectral peak frequency is approx. = 0.2-0.3 times the distance between the two 'hot spots' corresponding to two peaks. An important derivation of our model is the dynamical mass of the central star, M(sub *) approx. = 26 solar masses (D/1.2 kpc), D being the distance to the star. Prospects for improving the model are discussed.

Ponomarev, Victor O.↗
NASA NTRS1995

Radiative Instabilities in Three-Dimensional Astrophysical Masers

Inherent instabilities in the radiative transfer for astrophysical masers have been recognized and calculated in the linear maser idealization in our previous investigations. The same instabilities are now shown to occur in the more realistic, three-dimensional geometries. Fluctuations in the emergent flux result and may be related to the observed fluctuations in the radiative flux from the 1665 MHz OH masers that have been reported to occur on timescales as short as 1000 s. The time-dependent differential equations of radiative transfer are solved numerically for three-dimensional astrophysical masers. Computations are performed for spherical and elongated (rectangular parallelepiped) geometries.

Scappaticci, Gerardo A.↗
NASA NTRS2009

Traveling-Wave Maser for 32 GHz

The figure depicts a traveling-wave ruby maser that has been designed (though not yet implemented in hardware) to serve as a low-noise amplifier for reception of weak radio signals in the frequency band of 31.8 to 32.3 GHz. The design offers significant improvements over previous designs of 32-GHz traveling-wave masers. In addition, relative to prior designs of 32-GHz amplifiers based on high-electron-mobility transistors, this design affords higher immunity to radio-frequency interference and lower equivalent input noise temperature. In addition to the basic frequency-band and low-noise requirements, the initial design problem included a requirement for capability of operation in a closed-cycle helium refrigerator at a temperature .4 K and a requirement that the design be mechanically simplified, relative to prior designs, in order to minimize the cost of fabrication and assembly. Previous attempts to build 32- GHz traveling-wave masers involved the use of metallic slow-wave structures comprising coupled transverse electromagnetic (TEM)-mode resonators that were subject to very tight tolerances and, hence, were expensive to fabricate and assemble. Impedance matching for coupling signals into and out of these earlier masers was very difficult. A key feature of the design is a slow-wave structure, the metallic portions of which would be mechanically relatively simple in that, unlike in prior slow-wave structures, there would be no internal metal steps, irises, or posts. The metallic portions of the slow-wave structure would consist only of two rectangular metal waveguide arms. The arms would contain sections filled with the active material (ruby) alternating with evanescent-wave sections. This structure would be transparent in both the signal-frequency band (the aforementioned range of 31.8 to 32.3 GHz) and the pump-frequency band (65.75 to 66.75 GHz), and would impose large slowing factors in both frequency bands. Resonant ferrite isolators would be placed in the evanescent-wave sections to provide reverse loss needed to suppress reverse propagation of power at the signal frequency. This design is expected to afford a large gain-bandwidth product at the signal frequency and efficient coupling of the pump power into the paramagnetic spin resonances of the ruby sections. The more efficiently the pump power could be thus coupled, the more efficiently it could be utilized and the heat load on the refrigerator correspondingly reduced.

Shell, James↗
NASA NTRS1965

The helium system of the maser installation at the Goonhilly satellite-communication earth station

A travelling-wave solid-state maser anlplifier is used to provide the first stage of amplification in the receiving system at the communication-satellite earth-station at Goonhilly Downs. While the maser itself was built by an industrial research laboratory, the auxiliary supplies and equipment essential for the operation of the maser were designed and built by staff of the Post Office Research Station. A major part of this auxiliary equipment consists of apparatus for handling the helium refrigerant.

GROUND STATION↗
NASA NTRS1995

A Circumstellar H2O Maser Associated With the Galactic Circumnuclear Molecular Disk?

In the course of conducting a survey of 22-GHzH2O masers in the inner galaxy, we discovered a maser source in Sgr A West. It is located ~30'N and 35'E of Sgr A*, near the edge of the Eastern arm of the radio mini-spiral, which presumably coincides with the inside edge of the circumnuclear disk. Furthermore, the radial velocity of the maser is remarkably similar to that expected for gas in the circumnuclear disk at this location. We have also found a luminous, reddened star having a bolometric magnitude and IR spectrum characteristic of an M supergiant at this location. The extinction is consistent with a location in the inner galaxy, near or possibly within the circumnuclear disk. If this star is associated with the circumnuclear disk, it will have implications for star formation in the unusual galactic center environment.

Circumstellar Maser↗
DOE OSTI2024

Modelling of the electron cyclotron emission burst from a laboratory tokamak plasma with loss-cone maser instability

The maser instability associated with the loss-cone distribution has been widely invoked to explain the radio bursts observed in the astrophysical plasma environment, such as aurora and corona. In the laboratory plasma of a tokamak, events reminiscent of these radio bursts have also been frequently observed as an electron cyclotron emission (ECE) burst in the microwave range (~2f ce near the last closed flux surface) during transient magnetohydrodynamic events. These bursts have a short duration of ~10 μs and display a radiation spectrum corresponding to a radiation temperature T e,rad of over 30 keV while the edge thermal electron temperature T e is only in the range of 1 keV. Suprathermal electrons can be generated through magnetic reconnection, and a loss-cone distribution can be generated through open stochastic field lines in the magnetic mirror of the near-edge region of a tokamak plasma. Radiation modelling shows that a sharp distribution gradient ∂f/∂v ⊥ > 0 at the loss-cone boundary can cause a negative absorption of ECE radiation through the maser instability. The negative absorption then amplifies the radiation so that the microwave intensity is significantly stronger than the thermal value. The significant T e,rad from the simulations suggests the potential role of the loss-cone maser instability in generating the ECE burst in a tokamak.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1978

Analysis of hydrogen maser frequency drift due to possible drifts in load VSWR and phase angle of reflection coefficient

Theoretical equations are derived for calculating the effects of local VSWR and reflection coefficient phase angle drifts on hydrogen maser frequency stability. Sample calculations made for a typical JPL maser show that under special load conditions, a VSWR drift of 0.000075/h or phase angle drive of 0.01 deg/h can produce a frequency drift of (10 to the -14th power f sub 0) Hz/h where f sub 0 is the maser frequency of approximately 1.42 x 10 to the 9th power Hz.

Beatty, R. W.↗
NASA NTRS1977

New infrared objects associated with OH masers

Results of a search for IR radiation at 10 microns from a sample of OH maser sources are reported. An IR source is discovered near each of six OH masers which emit mainly at 1612 MHz in two distinct velocity ranges. It is shown that all the sources have varied with time, that two sources have exhibited significant variations in color temperature, and that the energy distributions of the six objects over the spectral range from 2 to 20 microns fall into two categories. Absorption in the 2.3-micron band of CO is detected in two sources, and four are found to display substantial silicate absorption features. The energy distributions of the sources indicate that pumping by 35-micron photons is feasible, but 2.8-micron pumping is very unlikely; the distributions are best explained as emission from very thick dust shells at temperatures of about 500 K. The data are taken as supporting the hypothesis that every double-peaked OH maser emitting principally at 1612 MHz is associated with an IR object. The nature of the objects inside the dust shells and their evolutionary state are briefly discussed.

Evans, N. J., II↗
NASA NTRS1978

New silicon monoxide masers

Seven Mira variable stars with silicon monoxide maser emission have been found. All are later than M4 and heavily reddened. Two were observed near maximum light. One, Y Cas, seems to bear out the correlation of 43-GHz SiO maser luminosity and mean spectral type at maximum light. RT Aql, however, falls about 1 mag below the expected brightness. A catalog of SiO maser stars is given.

Dickinson, D. F.↗
NASA NTRS1980

improving maser frequency stability

Hydrogen maser frequency standard is more stable by addition of parallel pyrex capillary tube array collimator. With collimator, maser line width has been made as narrow as 0.24 hertz representing fivefold improvement over maser without collimator. Fluorocarbon coating in tubes virtually eliminates energy loss in collimator.

Crampton, S. B.↗
NASA NTRS1978

Hydrogen maser frequency standard computer model for automatic cavity tuning servo simulations

A computer model of the JPL hydrogen maser frequency standard was developed. This model allows frequency stability data to be generated, as a function of various maser parameters, many orders of magnitude faster than these data can be obtained by experimental test. In particular, the maser performance as a function of the various automatic tuning servo parameters may be readily determined. Areas of discussion include noise sources, first-order autotuner loop, second-order autotuner loop, and a comparison of the loops.

Potter, P. D.↗
NASA NTRS1979

A small, passively operated hydrogen maser

The paper describes a compact passive hydrogen maser with unique features including a reduction in size. It uses a passive operation mode, permitting the use of a small microwave TE(011) cavity dielectrically loaded by a low loss alumina. The Teflon coated quartz bulb common in other masers has been replaced by a Teflon coating on the inside wall of the cavity producing a simpler designed and a more rugged H-maser package. The cavity and the attached endcaps comprise the vacuum envelope, allowing the use of a single vacuum system. The dimensional stability of the ceramic cavity under barometric changes is sufficiently within the range of the electronic cavity servo so that a second vacuum system is not required. For temperature control, a single oven is located in the magnetic shield nest.

Howe, D. A.↗